AD AD574AL 12-bit a/d converter Datasheet

AD574A* PRODUCT PAGE QUICK LINKS
Last Content Update: 02/23/2017
COMPARABLE PARTS
DESIGN RESOURCES
View a parametric search of comparable parts.
• AD574A Material Declaration
• PCN-PDN Information
DOCUMENTATION
• Quality And Reliability
Data Sheet
• Symbols and Footprints
• AD574A: Complete 12-Bit A/D Converter Data Sheet
• AD574A: Military Data Sheet
DISCUSSIONS
View all AD574A EngineerZone Discussions.
SOFTWARE AND SYSTEMS REQUIREMENTS
• JAN to Generic Cross Reference
SAMPLE AND BUY
Visit the product page to see pricing options.
REFERENCE MATERIALS
Technical Articles
TECHNICAL SUPPORT
• MS-2210: Designing Power Supplies for High Speed ADC
Submit a technical question or find your regional support
number.
DOCUMENT FEEDBACK
Submit feedback for this data sheet.
This page is dynamically generated by Analog Devices, Inc., and inserted into this data sheet. A dynamic change to the content on this page will not
trigger a change to either the revision number or the content of the product data sheet. This dynamic page may be frequently modified.
with V = +15 V or +12 V, V
AD574A–SPECIFICATIONS (@unless+258Cotherwise
noted)
CC
Model
AD574AJ
Typ
Max
AD574AK
Typ
Max
Max
Units
12
12
Bits
LINEARITY ERROR @ +25°C
TMIN to TMAX
±1
±1
± 1/2
± 1/2
± 1/2
± 1/2
LSB
LSB
12
Min
AD574AL
Typ
12
11
Min
= +5 V, VEE = –15 V or –12 V
RESOLUTION
DIFFERENTIAL LINEARITY ERROR
(Minimum Resolution for Which No
Missing Codes are Guaranteed)
TMIN to TMAX
Min
LOGIC
12
Bits
UNIPOLAR OFFSET (Adjustable to Zero)
±2
±1
±1
LSB
BIPOLAR OFFSET (Adjustable to Zero)
±4
±4
±2
LSB
0.125
% of FS
+70
°C
FULL-SCALE CALIBRATION ERROR
(With Fixed 50 Ω Resistor from REF OUT to REF IN)
(Adjustable to Zero)
TEMPERATURE RANGE
0.25
0
+70
0.25
0
+70
0
TEMPERATURE COEFFICIENTS
(Using Internal Reference)
TMIN to TMAX
Unipolar Offset
Bipolar Offset
Full-Scale Calibration
± 2 (10)
± 2 (10)
± 9 (50)
± 1 (5)
± 1 (5)
± 5 (27)
± 1 (5) LSB (ppm/°C)
± 1 (5) LSB (ppm/°C)
± 2 (10) LSB (ppm/°C)
POWER SUPPLY REJECTION
Max Change in Full-Scale Calibration
VCC = 15 V ± 1.5 V or 12 V ± 0.6 V
VLOGIC = 5 V ± 0.5 V
VEE = –15 V ± 1.5 V or –12 V ± 0.6 V
±2
± 1/2
±2
±1
± 1/2
±1
±1
± 1/2
±1
LSB
LSB
LSB
+5
+10
+10
+20
Volts
Volts
Volts
Volts
7
14
kΩ
kΩ
+5.5
+0.8
+20
Volts
Volts
µA
pF
ANALOG INPUT
Input Ranges
Bipolar
Unipolar
Input Impedance
10 Volt Span
20 Volt Span
DIGITAL CHARACTERISTICS 1 (TMIN–TMAX)
Inputs2 (CE, CS, R/C, A0)
Logic “1” Voltage
Logic “0” Voltage
Current
Capacitance
Output (DB11–DB0, STS)
Logic “1” Voltage (I SOURCE ≤ 500 µA)
Logic “0” Voltage (I SINK ≤ 1.6 mA)
Leakage (DB11–DB0, High-Z State)
Capacitance
POWER SUPPLIES
Operating Range
VLOGIC
VCC
VEE
Operating Current
ILOGIC
ICC
IEE
–5
–10
0
0
3
6
+2.0
–0.5
–20
PACKAGE OPTIONS 4
Ceramic (D-28)
Plastic (N-28)
PLCC (P-28A)
LCC (E-28A)
–5
–10
0
0
7
14
3
6
+5.5
+0.8
+20
+2.0
–0.5
–20
5
–5
–10
0
0
7
14
3
6
+5.5
+0.8
+20
+2.0
–0.5
–20
+4.5
+11.4
–11.4
+2.4
+0.4
+20
–20
5
30
2
18
40
5
30
390
725
10.0
10.02
1.5
AD574ASD
AD574AJN
AD574AJP
AD574AJE
+4.5
+11.4
–11.4
9.98
+0.4
+20
Volts
Volts
µA
pF
+5.5
+16.5
–16.5
Volts
Volts
Volts
30
2
18
40
5
30
mA
mA
mA
390
725
mW
10.0
10.01
1.5
Volts
mA
–20
5
+5.5
+16.5
–16.5
5
10
5
+2.4
+0.4
+20
–20
9.98
5
10
+5
+10
+10
+20
5
+2.4
POWER DISSIPATION
INTERNAL REFERENCE VOLTAGE
Output Current (Available for External Loads) 3
(External Load Should not Change During Conversion)
5
10
+5
+10
+10
+20
5
+5.5
+16.5
–16.5
30
2
18
40
5
30
390
725
10.0
10.02
1.5
AD574AKD
AD574AKN
AD574AKP
AD574AKE
+4.5
+11.4
–11.4
9.99
AD574ALD
AD574ALN
NOTES
Detailed Timing Specifications appear in the Timing Section.
12/8 Input is not TTL-compatible and must be hard wired to V LOGIC or Digital Common.
3
The reference should be buffered for operation on ± 12 V supplies.
4
D = Ceramic DIP; N = Plastic DIP; P = Plastic Leaded Chip Carrier.
Specifications subject to change without notice.
1
2
–2–
REV. B
AD574A
Model
Min
AD574AS
Typ
Max
Min
AD574AT
Typ
Max
Min
AD574AU
Typ Max
Units
RESOLUTION
12
12
12
Bits
LINEARITY ERROR @ +25°C
TMIN to TMAX
±1
±1
± 1/2
±1
± 1/2
±1
LSB
LSB
DIFFERENTIAL LINEARITY ERROR
(Minimum Resolution for Which No
Missing Codes are Guaranteed)
TMIN to TMAX
11
12
12
Bits
UNIPOLAR OFFSET (Adjustable to Zero)
±2
±1
±1
LSB
BIPOLAR OFFSET (Adjustable to Zero)
±4
±4
±2
LSB
0.125
% of FS
+125
°C
FULL-SCALE CALIBRATION ERROR
(With Fixed 50 Ω Resistor from REF OUT to REF IN)
(Adjustable to Zero)
TEMPERATURE RANGE
0.25
–55
0.25
+125
–55
+125
–55
TEMPERATURE COEFFICIENTS
(Using Internal Reference)
(TMIN to TMAX)
Unipolar Offset
Bipolar Offset
Full-Scale Calibration
± 2 (5)
± 4 (10)
± 20 (50)
± 1 (2.5)
± 2 (5)
± 10 (25)
± 1 (2.5) LSB (ppm/°C)
± 1 (2.5) LSB (ppm/°C)
± 5 (12.5) LSB (ppm/°C)
POWER SUPPLY REJECTION
Max Change in Full-Scale Calibration
VCC = 15 V ± 1.5 V or 12 V ± 0.6 V
VLOGIC = 5 V ± 0.5 V
VEE = –15 V ± 1.5 V or –12 V ± 0.6 V
±2
± 1/2
±2
±1
± 1/2
±1
±1
± 1/2
±1
LSB
LSB
LSB
+5
+10
+10
+20
Volts
Volts
Volts
Volts
7
14
kΩ
kΩ
+5.5
+0.8
+20
Volts
Volts
µA
pF
ANALOG INPUT
Input Ranges
Bipolar
Unipolar
Input Impedance
10 Volt Span
20 Volt Span
DIGITAL CHARACTERISTICS 1 (TMIN–TMAX)
Inputs2 (CE, CS, R/C, A0)
Logic “1” Voltage
Logic “0” Voltage
Current
Capacitance
Output (DB11–DB0, STS)
Logic “1” Voltage (I SOURCE ≤ 500 µA)
Logic “0” Voltage (I SINK ≤ 1.6 mA)
Leakage (DB11–DB0, High-Z State)
Capacitance
POWER SUPPLIES
Operating Range
VLOGIC
VCC
VEE
Operating Current
ILOGIC
ICC
IEE
–5
–10
0
0
3
6
+2.0
–0.5
–20
PACKAGE OPTION4
Ceramic (D-28)
–5
–10
0
0
7
14
3
6
+5.5
+0.8
+20
+2.0
–0.5
–20
5
7
14
3
6
+5.5
+0.8
+20
+2.0
–0.5
–20
+4.5
+11.4
–11.4
+2.4
30
2
18
40
5
30
390
725
10.0
10.02
1.5
AD574ASD
+4.5
+11.4
–11.4
9.98
Volts
Volts
µA
pF
+5.5
+16.5
–16.5
Volts
Volts
Volts
30
2
18
40
5
30
mA
mA
mA
390
725
mW
5
+5.5
+16.5
–16.5
30
2
18
40
5
30
390
725
10.0
10.02
1.5
AD574ATD
–3–
+0.4
+20
–20
5
+5.5
+16.5
–16.5
5
10
5
+0.4
+20
–20
5
NOTES
1
Detailed Timing Specifications appear in the Timing Section.
2
12/8 Input is not TTL-compatible and must be hard wired to V LOGIC or Digital Common.
3
The reference should be buffered for operation on ± 12 V supplies.
4
D = Ceramic DIP.
Specifications subject to change without notice.
REV. B
–5
–10
0
0
+2.4
+0.4
+20
–20
9.98
5
10
+5
+10
+10
+20
5
+2.4
POWER DISSIPATION
INTERNAL REFERENCE VOLTAGE
Output Current (Available for External Loads) 3
(External Load Should not Change During Conversion)
5
10
+5
+10
+10
+20
+4.5
+11.4
–11.4
9.99
10.0 10.01
1.5
AD574AUD
Volts
mA
AD574A
+5V SUPPLY
VLOGIC
DATA MODE SELECT
12/8
CHIP SELECT
CS
BYTE ADDRESS/
SHORT CYCLE
AO
READ/CONVERT
R/C
CHIP ENABLE
CE
+12/+15V SUPPLY
VCC
+10V REFERENCE
REF OUT
ANALOG COMMON
AC
REFERENCE INPUT
REF IN
-12/-15V SUPPLY
VEE
BIPOLAR OFFSET
BIP OFF
10V SPAN INPUT
10VIN
1
STATUS
STS
DB11
27
MSB
28
MSB
2
CONTROL
3
3
4
5
SAR
CLOCK
6
12
3k
7
COMP 12
10V
REF
8
9
10
19.95k
IDAC
IDAC =
4 x N x IREF
8k
IREF
11
12
9.95k
5k
13
20V SPAN INPUT 14
20VIN
DAC N
VEE
S
T
A
T
E
O
U
T
P
U
T
B
U
F
F
E
R
S
N
I
B
B
L
E
A
24 DB8
23 DB7
N
I
B
B
L
E
19 DB3
C
22 DB6
21 DB5
DIGITAL
DATA
OUTPUTS
20 DB4
18 DB2
17 DB1
DB0
16 LSB
15 DIGITAL COMMON
DC
12
AD574A
25 DB9
N
I
B
B
L
E
B
LSB
5k
26 DB10
AD574A Block Diagram and Pin Configuration
ABSOLUTE MAXIMUM RATINGS*
(Specifications apply to all grades, except where noted)
VCC to Digital Common . . . . . . . . . . . . . . . . . . 0 V to +16.5 V
VEE to Digital Common . . . . . . . . . . . . . . . . . . . 0 V to –16.5 V
VLOGIC to Digital Common . . . . . . . . . . . . . . . . . . 0 V to +7 V
Analog Common to Digital Common . . . . . . . . . . . . . . . ± 1 V
Control Inputs (CE, CS, AO 12/8, R/C) to
Digital Common . . . . . . . . . . . . . . –0.5 V to VLOGIC + 0.5 V
Analog Inputs (REF IN, BIP OFF, 10 VIN) to
Analog Common . . . . . . . . . . . . . . . . . . . . . . . . . VEE to VCC
20 VIN to Analog Common . . . . . . . . . . . . . . . . . . . . . . ± 24 V
REF OUT . . . . . . . . . . . . . . . . . . Indefinite Short to Common
Momentary Short to VCC
Chip Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175°C
Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 825 mW
Lead Temperature (Soldering, 10 sec). . . . . . . . . . . . . +300°C
Storage Temperature (Ceramic) . . . . . . . . . . –65°C to +150°C
(Plastic) . . . . . . . . . . . . . . . . . . . . . . . . . . . –25°C to +100°C
*Stresses above those listed under “Absolute Maximum Ratings” may cause
permanent damage to the device. This is a stress rating only and functional
operation of the device at these or any other conditions above those indicated in the
operational sections of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
ORDERING GUIDE
Model1
Temperature
Range
Linearity Error
Max (TMIN to TMAX)
Resolution
No Missing Codes
(TMIN to TMAX)
Max
Full Scale
T.C. (ppm/°C)
AD574AJ(X)
AD574AK(X)
AD574AL(X)
AD574AS(X)2
AD574AT(X)2
AD574AU(X)2
0°C to +70°C
0°C to +70°C
0°C to +70°C
–55°C to +125°C
–55°C to +125°C
–55°C to +125°C
± 1 LSB
± 1/2 LSB
± 1/2 LSB
± 1 LSB
± 1 LSB
± 1 LSB
11 Bits
12 Bits
12 Bits
11 Bits
12 Bits
12 Bits
50.0
27.0
10.0
50.0
25.0
12.5
NOTES
1
X = Package designator. Available packages are: D (D-28) for all grades. E (E-28A) for J and K grades and /883B processed S, T
and U grades. N (N-28) for J, K, and L grades. P (P-28A) for PLCC in J, K grades. Example: AD574AKN is K grade in plastic DIP.
2
For details on grade and package offerings screened in accordance with MIL-STD-883, refer to Analog Devices Military Products
Databook.
–4–
REV. B
AD574A
THE AD574A OFFERS GUARANTEED MAXIMUM LINEARITY ERROR OVER THE FULL OPERATING
TEMPERATURE RANGE
DEFINITIONS OF SPECIFICATIONS
QUANTIZATION UNCERTAINTY
LINEARITY ERROR
Linearity error refers to the deviation of each individual code
from a line drawn from “zero” through “full scale”. The point
used as “zero” occurs 1/2 LSB (1.22 mV for 10 volt span) before the first code transition (all zeros to only the LSB “on”).
“Full scale” is defined as a level 1 1/2 LSB beyond the last code
transition (to all ones). The deviation of a code from the true
straight line is measured from the middle of each particular
code.
Analog-to-digital converters exhibit an inherent quantization
uncertainty of ± 1/2 LSB. This uncertainty is a fundamental
characteristic of the quantization process and cannot be reduced
for a converter of given resolution.
LEFT-JUSTIFIED DATA
The data format used in the AD574A is left-justified. This
means that the data represents the analog input as a fraction of
4095
full-scale, ranging from 0 to 4096 . This implies a binary point
to the left of the MSB.
The AD574AK, L, T, and U grades are guaranteed for maximum nonlinearity of ± 1/2 LSB. For these grades, this means
that an analog value which falls exactly in the center of a given
code width will result in the correct digital output code. Values
nearer the upper or lower transition of the code width may produce the next upper or lower digital output code. The AD574AJ
and S grades are guaranteed to ± 1 LSB max error. For these
grades, an analog value which falls within a given code width
will result in either the correct code for that region or either
adjacent one.
FULL-SCALE CALIBRATION ERROR
The last transition (from 1111 1111 1110 to 1111 1111 1111)
should occur for an analog value 1 1/2 LSB below the nominal
full scale (9.9963 volts for 10.000 volts full scale). The full-scale
calibration error is the deviation of the actual level at the last
transition from the ideal level. This error, which is typically
0.05% to 0.1% of full scale, can be trimmed out as shown in
Figures 3 and 4.
Note that the linearity error is not user-adjustable.
TEMPERATURE COEFFICIENTS
DIFFERENTIAL LINEARITY ERROR (NO MISSING
CODES)
The temperature coefficients for full-scale calibration, unipolar
offset, and bipolar offset specify the maximum change from the
initial (25°C) value to the value at TMIN or TMAX.
A specification which guarantees no missing codes requires that
every code combination appear in a monotonic increasing sequence as the analog input level is increased. Thus every code
must have a finite width. For the AD574AK, L, T, and U
grades, which guarantee no missing codes to 12-bit resolution,
all 4096 codes must be present over the entire operating temperature ranges. The AD574AJ and S grades guarantee no missing codes to 11-bit resolution over temperature; this means that
all code combinations of the upper 11 bits must be present; in
practice very few of the 12-bit codes are missing.
The standard specifications for the AD574A assume use of
+5.00 V and ± 15.00 V or ± 12.00 V supplies. The only effect of
power supply error on the performance of the device will be a
small change in the full-scale calibration. This will result in a
linear change in all lower order codes. The specifications show
the maximum full-scale change from the initial value with the
supplies at the various limits.
UNIPOLAR OFFSET
CODE WIDTH
POWER SUPPLY REJECTION
The first transition should occur at a level 1/2 LSB above analog
common. Unipolar offset is defined as the deviation of the actual
transition from that point. This offset can be adjusted as discussed
on the following two pages. The unipolar offset temperature
coefficient specifies the maximum change of the transition point
over temperature, with or without external adjustment.
A fundamental quantity for A/D converter specifications is the
code width. This is defined as the range of analog input values
for which a given digital output code will occur. The nominal
value of a code width is equivalent to 1 least significant bit
(LSB) of the full-scale range or 2.44 mV out of 10 volts for a
12-bit ADC.
BIPOLAR OFFSET
In the bipolar mode the major carry transition (0111 1111 1111
to 1000 0000 0000) should occur for an analog value 1/2 LSB
below analog common. The bipolar offset error and temperature
coefficient specify the initial deviation and maximum change in
the error over temperature.
REV. B
–5–
AD574A
CIRCUIT OPERATION
DRIVING THE AD574 ANALOG INPUT
The AD574A is a complete 12-bit A/D converter which requires
no external components to provide the complete successiveapproximation analog-to-digital conversion function. A block
diagram of the AD574A is shown in Figure 1.
The internal circuitry of the AD574 dictates that its analog
input be driven by a low source impedance. Voltage changes at
the current summing node of the internal comparator result in
abrupt modulations of the current at the analog input. For accurate 12-bit conversions the driving source must be capable of
holding a constant output voltage under these dynamically
changing load conditions.
+5V SUPPLY
VLOGIC
DATA MODE SELECT
12/8
CHIP SELECT
CS
BYTE ADDRESS/
SHORT CYCLE
AO
READ/CONVERT
R/C
CHIP ENABLE
CE
+12/+15V SUPPLY
VCC
+10V REFERENCE
REF OUT
ANALOG COMMON
AC
REFERENCE INPUT
REF IN
-12/-15V SUPPLY
VEE
BIPOLAR OFFSET
BIP OFF
10V SPAN INPUT
10VIN
1
28
MSB
2
CONTROL
3
3
4
5
SAR
CLOCK
6
3k
7
COMP 12
8
10V
REF
9
10
19.95k
IDAC
IDAC =
4 x N x IREF
8k
IREF
11
12
9.95k
5k
13
20V SPAN INPUT 14
20VIN
DAC N
VEE
12
S
T
A
T
E
O
U
T
P
U
T
B
U
F
F
E
R
S
N
I
B
B
L
E
A
N
I
B
B
L
E
B
AD574A
12
STATUS
STS
DB11
MSB
26 DB10
FEEDBACK TO AMPLIFIER
25 DB9
V+
24 DB8
23 DB7
22 DB6
21 DB5
AD574A
DIGITAL
DATA
OUTPUTS
CURRENT
LIMITING
RESISTORS
RIN
20 DB4
IIN IS MODULATED BY
N
I
B
B
L
E
C
LSB
5k
27
19 DB3
18 DB2
V–
17 DB1
iDIFF
CHANGES IN TEST CURRENT.
AMPLIFIER PULSE LOAD
RESPONSE LIMITED BY
OPEN LOOP OUTPUT IMPEDANCE.
ANALOG COMMON
IIN
iTEST
CURRENT
OUTPUT
DAC
COMPARATOR
SAR
DB0
16 LSB
15
Figure 2. Op Amp – AD574A Interface
DIGITAL COMMON
DC
Figure 1. Block Diagram of AD574A 12-Bit A-to-D Converter
When the control section is commanded to initiate a conversion
(as described later), it enables the clock and resets the successiveapproximation register (SAR) to all zeros. Once a conversion
cycle has begun, it cannot be stopped or restarted and data is
not available from the output buffers. The SAR, timed by the
clock, will sequence through the conversion cycle and return an
end-of-convert flag to the control section. The control section
will then disable the clock, bring the output status flag low, and
enable control functions to allow data read functions by external
command.
During the conversion cycle, the internal 12-bit current output
DAC is sequenced by the SAR from the most significant bit
(MSB) to least significant bit (LSB) to provide an output current which accurately balances the input signal current through
the 5 kΩ (or 10 kΩ) input resistor. The comparator determines
whether the addition of each successively-weighted bit current
causes the DAC current sum to be greater or less than the input
current; if the sum is less, the bit is left on; if more, the bit is
turned off. After testing all the bits, the SAR contains a 12-bit
binary code which accurately represents the input signal to
within ± 1/2 LSB.
The temperature-compensated buried Zener reference provides
the primary voltage reference to the DAC and guarantees excellent stability with both time and temperature. The reference is
trimmed to 10.00 volts ± 0.2%; it can supply up to 1.5 mA to an
external load in addition to the requirements of the reference input resistor (0.5 mA) and bipolar offset resistor (1 mA) when
the AD574A is powered from ± 15 V supplies. If the AD574A is
used with ± 12 V supplies, or if external current must be supplied over the full temperature range, an external buffer amplifier is recommended. Any external load on the AD574A
reference must remain constant during conversion. The
thin-film application resistors are trimmed to match the
full-scale output current of the DAC. There are two 5 kΩ input
scaling resistors to allow either a 10 volt or 20 volt span. The
10 kΩ bipolar offset resistor is grounded for unipolar operation
and connected to the 10 volt reference for bipolar operation.
The output impedance of an op amp has an open-loop value
which, in a closed loop, is divided by the loop gain available at
the frequency of interest. The amplifier should have acceptable
loop gain at 500 kHz for use with the AD574A. To check
whether the output properties of a signal source are suitable,
monitor the AD574’s input with an oscilloscope while a conversion is in progress. Each of the 12 disturbances should subside
in 1 µs or less.
For applications involving the use of a sample-and-hold amplifier, the AD585 is recommended. The AD711 or AD544 op
amps are recommended for dc applications.
SAMPLE-AND-HOLD AMPLIFIERS
Although the conversion time of the AD574A is a maximum of
35 µs, to achieve accurate 12-bit conversions of frequencies
greater than a few Hz requires the use of a sample-and-hold
amplifier (SHA). If the voltage of the analog input signal driving
the AD574A changes by more than 1/2 LSB over the time
interval needed to make a conversion, then the input requires a
SHA.
The AD585 is a high linearity SHA capable of directly driving
the analog input of the AD574A. The AD585’s fast acquisition
time, low aperture and low aperture jitter are ideally suited for
high-speed data acquisition systems. Consider the AD574A
converter with a 35 µs conversion time and an input signal of
10 V p-p: the maximum frequency which may be applied to
achieve rated accuracy is 1.5 Hz. However, with the addition of
an AD585, as shown in Figure 3, the maximum frequency
increases to 26 kHz.
The AD585’s low output impedance, fast-loop response, and
low droop maintain 12-bits of accuracy under the changing load
conditions that occur during a conversion, making it suitable for
use in high accuracy conversion systems. Many other SHAs
cannot achieve 12-bits of accuracy and can thus compromise a
system. The AD585 is recommended for AD574A applications
requiring a sample and hold.
An alternate approach is to use the AD1674, which combines
the ADC and SHA on one chip, with a total throughput time of
10 µs.
–6–
REV. B
AD574A
+VS
TO A1
VREF
A
–VS
TO A1
AGND
+
+
C2
2 12/8
+VS
9
R2
100Ω
8
10k 10k
GAIN
+15V
100pF
A1
AD585
1
2
3
4
5
6
R1
100k
OFFSET
7
–VS
ANALOG
INPUT
0V TO +10V
CONVERT
C3
–15V
11 1
14 13 12 11 10
page. Analog input connections and calibration are easily accomplished; the unipolar operating mode is shown in Figure 4.
+15V
+5V
+
C1
10
R4
100k
27
A2
3
4
15
A
HIGH 27
BIT 24
4 AO
+12V/+15V
–12V/–15V
5 R/C
MIDDLE 23
BITS 20
6 CE
AD574A
GAIN
16
12
9
R3
–15V 100Ω
12-BIT
3-STATE
DATA
3 CS
OFFSET
R1
100k
8
13
STS 28
2 6 7
100k
R2
100Ω
AD574A
10 REF IN
8 REF OUT
100Ω
12 BIP OFF
28
5
+5V
0 TO +10V
7404 OR EQ.
LOW 19
BITS 16
1
13 10VIN
STATUS
ANALOG
INPUTS
NOTE
1. C1, C2, C3 ARE 47mF
µ TANTALUM, BYPASSED BY
0.1mF
µ CERAMIC. LOCATE AT ASSOCIATED A2 PINS.
14 20VIN
+15V
7
–15V
11
0 TO +20V
9 ANA COM
DIG COM 15
Figure 3. AD574A with AD585 Sample and Hold
SUPPLY DECOUPLING AND LAYOUT
CONSIDERATIONS
Figure 4. Unipolar Input Connections
It is critically important that the AD574A power supplies be filtered, well regulated, and free from high frequency noise. Use of
noisy supplies will cause unstable output codes. Switching
power supplies are not recommended for circuits attempting to
achieve 12-bit accuracy unless great care is used in filtering any
switching spikes present in the output. Remember that a few
millivolts of noise represents several counts of error in a 12-bit
ADC.
All of the thin-film application resistors of the AD574A are
trimmed for absolute calibration. Therefore, in many applications, no calibration trimming will be required. The absolute
accuracy for each grade is given in the specification tables.
For example, if no trims are used, the AD574AK guarantees
± 1 LSB max zero offset error and ± 0.25% (10 LSB) max
full-scale error. (Typical full-scale error is ± 2 LSB.) If the offset
trim is not required, Pin 12 can be connected directly to Pin 9;
the two resistors and trimmer for Pin 12 are then not needed. If
the full-scale trim is not needed, a 50 Ω ± 1% metal film resistor
should be connected between Pin 8 and Pin 10.
Decoupling capacitors should be used on all power supply pins;
the +5 V supply decoupling capacitor should be connected
directly from Pin 1 to Pin 15 (digital common) and the +VCC
and –VEE pins should be decoupled directly to analog common
(Pin 9). A suitable decoupling capacitor is a 4.7 µF tantalum
type in parallel with a 0.1 µF disc ceramic type.
The analog input is connected between Pin 13 and Pin 9 for a
0 V to +10 V input range, between 14 and Pin 9 for a 0 V to
+20 V input range. The AD574A easily accommodates an input
signal beyond the supplies. For the 10 volt span input, the LSB
has a nominal value of 2.44 mV; for the 20 volt span, 4.88 mV.
If a 10.24 V range is desired (nominal 2.5 mV/bit), the gain
trimmer (R2) should be replaced by a 50 Ω resistor, and a
200 Ω trimmer inserted in series with the analog input to Pin 13
for a full-scale range of 20.48 V (5 mV/bit), use a 500 Ω trimmer into Pin 14. The gain trim described below is now done
with these trimmers. The nominal input impedance into Pin 13
is 5 kΩ, and 10 kΩ into Pin 14.
Circuit layout should attempt to locate the AD574A, associated
analog input circuitry, and interconnections as far as possible
from logic circuitry. For this reason, the use of wire-wrap circuit
construction is not recommended. Careful printed circuit construction is preferred.
GROUNDING CONSIDERATIONS
The analog common at Pin 9 is the ground reference point for
the internal reference and is thus the “high quality” ground for
the AD574A; it should be connected directly to the analog reference point of the system. In order to achieve all of the high
accuracy performance available from the AD574A in an environment of high digital noise content, the analog and digital
commons should be connected together at the package. In some
situations, the digital common at Pin 15 can be connected to
the most convenient ground reference point; analog power
return is preferred.
UNIPOLAR CALIBRATION
The AD574A is intended to have a nominal 1/2 LSB offset so
that the exact analog input for a given code will be in the middle
of that code (halfway between the transitions to the codes above
and below it). Thus, the first transition (from 0000 0000 0000
to 0000 0000 0001) will occur for an input level of +1/2 LSB
(1.22 mV for 10 V range).
If Pin 12 is connected to Pin 9, the unit will behave in this manner, within specifications. If the offset trim (R1) is used, it
should be trimmed as above, although a different offset can be
set for a particular system requirement. This circuit will give approximately ± 15 mV of offset trim range.
UNIPOLAR RANGE CONNECTIONS FOR THE AD574A
The AD574A contains all the active components required to
perform a complete 12-bit A/D conversion. Thus, for most situations, all that is necessary is connection of the power supplies
(+5 V, +12 V/+15 V and –12 V/–15 V), the analog input, and
the conversion initiation command, as discussed on the next
REV. B
–7–
AD574A
The full-scale trim is done by applying a signal 1 1/2 LSB below
the nominal full scale (9.9963 for a 10 V range). Trim R2 to
give the last transition (1111 1111 1110 to 1111 1111 1111).
START CONVERT
BIPOLAR OPERATION
STATUS
The connections for bipolar ranges are shown in Figure 5.
Again, as for the unipolar ranges, if the offset and gain specifications are sufficient, one or both of the trimmers shown can be
replaced by a 50 Ω ± 1% fixed resistor. Bipolar calibration is
similar to unipolar calibration. First, a signal 1/2 LSB above
negative full scale (–4.9988 V for the ± 5 V range) is applied and
R1 is trimmed to give the first transition (0000 0000 0000 to
0000 0000 0001). Then a signal 1 1/2 LSB below positive full
scale (+4.9963 V the ± 5 V range) is applied and R2 trimmed to
give the last transition (1111 11111110 to 1111 1111 1111).
2 12/8
5 R/C
R2
100Ω
AD574A
10 REF IN
OFFSET
65V
ANALOG
INPUTS
610V
12 BIP OFF
R1
100Ω
+5V
1
+15V
7
13 10VIN
14 20VIN
9 ANA COM
FROM
NOTE 1
NIBBLE A, B,
ENABLE
NIBBLE C
ENABLE
TO OUTPUT
BUFFERS
NIBBLE B = O
ENABLE
NOTE 1: WHEN START CONVERT GOES LOW, THE EOC (END OF CONVERSION) SIGNALS GO LOW.
EOC8 RETURNS HIGH AFTER AN 8-BIT CONVERSION CYCLE IS COMPLETE, AND EOC12
RETURNS HIGH WHEN ALL 12-BITS HAVE BEEN CONVERTED. THE EOC SIGNALS PREVENT
DATA FROM BEING READ DURING CONVERSIONS.
NOTE 2: 12/8 IS NOT A TTL-COMPATABLE INPUT AND SHOULD ALWAYS BE WIRED DIRECTLY TO
VLOGIC OR DIGITAL COMMON.
LOW 19
BITS 16
8 REF OUT
EOC8
EOC12
12/8
(NOTE 2)
MIDDLE 23
BITS 20
6 CE
VALUE OF A0
AT LAST CONVERT
COMMAND
READ
27
HIGH
BIT 24
4 AO
LOW IF CONVERSION
IN PROGRESS
CONVERT
A0
STS 28
3 CS
GAIN
R/C
CE
CS
Figure 6. AD574A Control Logic
An output signal, STS, indicates the status of the converter.
STS goes high at the beginning of a conversion and returns low
when the conversion cycle is complete.
Table I. AD574A Truth Table
–15V 11
DIG COM 15
Figure 5. Bipolar Input Connections
CONTROL LOGIC
The AD574A contains on-chip logic to provide conversion initiation and data read operations from signals commonly available in microprocessor systems. Figure 6 shows the internal
logic circuitry of the AD574A.
The control signals CE, CS, and R/C control the operation of
the converter. The state of R/C when CE and CS are both
asserted determines whether a data read (R/C = 1) or a convert
(R/C = 0) is in progress. The register control inputs AO and
12/8 control conversion length and data format. The AO line is
usually tied to the least significant bit of the address bus. If a
conversion is started with AO low, a full 12-bit conversion cycle
is initiated. If AO is high during a convert start, a shorter 8-bit
conversion cycle results. During data read operations, AO determines whether the three-state buffers containing the 8 MSBs of
the conversion result (AO = 0) or the 4 LSBs (AO = 1) are
enabled. The 12/8 pin determines whether the output data is
to be organized as two 8-bit words (12/8 tied to DIGITAL
COMMON) or a single 12-bit word (12/8 tied to VLOGIC). The
12/8 pin is not TTL-compatible and must be hard-wired to
either VLOGIC or DIGITAL COMMON. In the 8-bit mode, the
byte addressed when AO is high contains the 4 LSBs from the
conversion followed by four trailing zeroes. This organization
allows the data lines to be overlapped for direct interface to
8-bit buses without the need for external three-state buffers.
It is not recommended that AO change state during a data read
operation. Asymmetrical enable and disable times of the
three-state buffers could cause internal bus contention resulting
in potential damage to the AD574A.
CE CS R/C 12/8
AO
Operation
0
X
X
1
X
X
X
X
X
X
None
None
1
1
0
0
0
0
X
X
0
1
Initiate 12-Bit Conversion
Initiate 8-Bit Conversion
1
0
1
Pin 1 X
Enable 12-Bit Parallel Output
1
1
0
0
1
1
Pin 15 0
Pin 15 1
Enable 8 Most Significant Bits
Enable 4 LSBs + 4 Trailing Zeroes
TIMING
The AD574A is easily interfaced to a wide variety of microprocessors and other digital systems. The following discussion of
the timing requirements of the AD574A control signals should
provide the system designer with useful insight into the operation of the device.
Table II. Convert Start Timing—Full Control Mode
Symbol
Parameter
tDSC
tHEC
tSSC
tHSC
tSRC
tHRC
tSAC
tHAC
tC
STS Delay from CE
CE Pulse Width
CS to CE Setup
CS Low During CE High
R/C to CE Setup
R/C Low During CE High
AO to CE Setup
AO Valid During CE High
Conversion Time
8-Bit Cycle
12-Bit Cycle
–8–
Min
Typ Max
400
ns
ns
ns
ns
ns
ns
ns
ns
24
35
µs
µs
300
300
200
250
200
0
300
10
15
Units
REV. B
AD574A
Figure 7 shows a complete timing diagram for the AD574A convert start operation. R/C should be low before both CE and CS
are asserted; if R/C is high, a read operation will momentarily
occur, possibly resulting in system bus contention. Either CE or
CS may be used to initiate a conversion; however, use of CE is
recommended since it includes one less propagation delay than
CS and is the faster input. In Figure 7, CE is used to initiate the
conversion.
Table III. Read Timing—Full Control Mode
Symbol
Parameter
tDD1
tHD
tHL2
tSSR
tSRR
tSAR
tHSR
tHRR
tHAR
Access Time (from CE)
Data Valid After CE Low
Output Float Delay
CS to CE Setup
R/C to CE Setup
AO to CE Setup
CS Valid After CE Low
R/C High After CE Low
AO Valid After CE Low
Min Typ
Max Units
200
25
100
150
0
150
50
0
50
ns
ns
ns
ns
ns
ns
ns
ns
ns
NOTES
1
tDD is measured with the load circuit of Figure 9 and defined as the time
required for an output to cross 0.4 V or 2.4 V.
2
tHL is defined as the time required for the data lines to change 0.5 V when
loaded with the circuit of Figure 10.
Figure 7. Convert Start Timing
Once a conversion is started and the STS line goes high, convert
start commands will be ignored until the conversion cycle is
complete. The output data buffers cannot be enabled during
conversion.
a. High-Z to Logic 1
b. High-Z to Logic 0
Figure 9. Load Circuit for Access Time Test
Figure 8 shows the timing for data read operations. During data
read operations, access time is measured from the point where
CE and R/C both are high (assuming CS is already low). If CS
is used to enable the device, access time is extended by 100 ns.
a. Logic 1 to High-Z b. Logic 0 to High-Z
Figure 10. Load Circuit for Output Float Delay Test
“STAND-ALONE” OPERATION
The AD574A can be used in a “stand-alone” mode, which is
useful in systems with dedicated input ports available and thus
not requiring full bus interface capability.
In this mode, CE and 12/8 are wired high, CS and AO are wired
low, and conversion is controlled by R/C. The three-state buffers are enabled when R/C is high and a conversion starts when
R/C goes low. This allows two possible control signals—a high
pulse or a low pulse. Operation with a low pulse is shown in
Figure 11. In this case, the outputs are forced into the high
impedance state in response to the falling edge of R/C and return
Figure 8. Read Cycle Timing
In the 8-bit bus interface mode (12/8 input wired to DIGITAL
COMMON), the address bit, AO, must be stable at least 150 ns
prior to CE going high and must remain stable during the entire
read cycle. If AO is allowed to change, damage to the AD574A
output buffers may result.
Figure 11. Low Pulse for R/C—Outputs Enabled After
Conversion
REV. B
–9–
AD574A
GENERAL A/D CONVERTER INTERFACE
CONSIDERATIONS
to valid logic levels after the conversion cycle is completed. The
STS line goes high 600 ns after R/C goes low and returns low
300 ns after data is valid.
If conversion is initiated by a high pulse as shown in Figure 12,
the data lines are enabled during the time when R/C is high.
The falling edge of R/C starts the next conversion, and the data
lines return to three-state (and remain three-state) until the next
high pulse of R/C.
Figure 12. High Pulse for R/C—Outputs Enabled While R/C
High, Otherwise High-Z
Table IV. Stand-Alone Mode Timing
Symbol
Parameter
Min Typ Max
Units
tHRL
tDS
tHDR
tHL
tHS
tHRH
tDDR
Low R/C Pulse Width
STS Delay from R/C
Data Valid After R/C Low
Output Float Delay
STS Delay After Data Valid
High R/C Pulse Width
Data Access Time
250
ns
ns
ns
ns
ns
ns
ns
600
25
300
300
150
1000
250
Usually the low pulse for R/C stand-alone mode will be used.
Figure 13 illustrates a typical stand-alone configuration for 8086
type processors. The addition of the 74F/S374 latches improves
bus access/release times and helps minimize digital feedthrough
to the analog portion of the converter.
A typical A/D converter interface routine involves several
operations. First, a write to the ADC address initiates a conversion. The processor must then wait for the conversion cycle to
complete, since most ADCs take longer than one instruction
cycle to complete a conversion. Valid data can, of course, only
be read after the conversion is complete. The AD574A provides
an output signal (STS) which indicates when a conversion is in
progress. This signal can be polled by the processor by reading
it through an external three-state buffer (or other input port).
The STS signal can also be used to generate an interrupt upon
completion of conversion, if the system timing requirements are
critical (bear in mind that the maximum conversion time of the
AD574A is only 35 microseconds) and the processor has other
tasks to perform during the ADC conversion cycle. Another
possible time-out method is to assume that the ADC will take
35 microseconds to convert, and insert a sufficient number of
“do-nothing” instructions to ensure that 35 microseconds of
processor time is consumed.
Once it is established that the conversion is finished, the data
can be read. In the case of an ADC of 8-bit resolution (or less),
a single data read operation is sufficient. In the case of converters with more data bits than are available on the bus, a choice of
data formats is required, and multiple read operations are needed.
The AD574A includes internal logic to permit direct interface
to 8-bit or 16-bit data buses, selected by connection of the 12/8
input. In 16-bit bus applications (12/8 high) the data lines
(DB11 through DB0) may be connected to either the 12 most
significant or 12 least significant bits of the data bus. The remaining four bits should be masked in software. The interface
to an 8-bit data bus (12/8 low) is done in a left-justified format.
The even address (A0 low) contains the 8 MSBs (DB11 through
DB4). The odd address (A0 high) contains the 4 LSBs (DB3
through DB0) in the upper half of the byte, followed by four
trailing zeroes, thus eliminating bit masking instructions.
It is not possible to rearrange the AD574A data lines for right
justified 8-bit bus interface.
Figure 14. AD574A Data Format for 8-Bit Bus
SPECIFIC PROCESSOR INTERFACE EXAMPLES
Z-80 System Interface
Figure 13. 8086 Stand-Alone Configuration
INTERFACING THE AD574A TO MICROPROCESSORS
The control logic of the AD574A makes direct connection to
most microprocessor system buses possible. While it is impossible to describe the details of the interface connections for every
microprocessor type, several representative examples will be
described here.
The AD574A may be interfaced to the Z-80 processor in an I/O
or memory mapped configuration. Figure 15 illustrates an I/O
or mapped configuration. The Z-80 uses address lines A0–A7 to
decode the I/O port address.
An interesting feature of the Z-80 is that during I/O operations a
single wait state is automatically inserted, allowing the AD574A
to be used with Z-80 processors having clock speeds up to 4 MHz.
For applications faster than 4 MHz use the wait state generator
in Figure 16. In a memory mapped configuration the AD574A
may be interfaced to Z-80 processors with clock speeds of up to
2.5 MHz.
–10–
REV. B
AD574A
Note: Due to the large number of options that may be installed
in the PC, the I/O bus loading should be limited to one Schottky
TTL load. Therefore, a buffer/driver should be used when interfacing more than two AD574As to the I/O bus.
8086 Interface
The data mode select pin (12/8) of the AD574A should be connected to VLOGIC to provide a 12-bit data output. To prevent
possible bus contention, a demultiplexed and buffered address/
data bus is recommended. In the cases where the 8-bit short
conversion cycle is not used, A0 should be tied to digital common. Figure 18 shows a typical 8086 configuration.
Figure 15. Z80—AD574A Interface
Figure 16. Wait State Generator
IBM PC Interface
The AD574A appears in Figure 17 interfaced to the 4 MHz
8088 processor of an IBM PC. Since the device resides in I/O
space, its address is decoded from only the lower ten address
lines and must be gated with AEN (active low) to mask out internal DMA cycles which use the same I/O address space. This
active low signal is applied to CS. IOR and IOW are used to
initiate the conversion and read, and are gated together to drive
the chip enable, CE. Because the data bus width is limited to
8 bits, the AD574A data resides in two adjacent addresses
selected by A0.
Figure 18. 8086—AD574A with Buffered Bus lnterface
For clock speeds greater than 4 MHz wait state insertion similar
to Figure 16 is recommended to ensure sufficient CE and R/C
pulse duration.
The AD574A can also be interfaced in a stand-alone mode (see
Figure 13). A low going pulse derived from the 8086’s WR signal logically ORed with a low address decode starts the conversion. At the end of the conversion, STS clocks the data into the
three-state latches.
68000 Interface
The AD574, when configured in the stand-alone mode, will easily interface to the 4 MHz version of the 68000 microprocessor.
The 68000 R/W signal combined with a low address decode initiates conversion. The UDS or LDS signal, with the decoded
address, generates the DTACK input to the processor, latching
in the AD574A’s data. Figure 19 illustrates this configuration.
Figure 17. IBM PC—AD574A Interface
REV. B
Figure 19. 68000—AD574A Interface
–11–
AD574A
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
28-Lead Plastic DIP Package (N-28A)
C704d–10–8/88
28-Pin Ceramic DIP Package (D-28)
28-Terminal PLCC Package (P-28A)
0.180 (4.57)
0.165 (4.19)
0.048 (1.21)
0.042 (1.07)
0.048 (1.21)
0.042 (1.07)
0.056 (1.42)
0.042 (1.07)
4
5
PIN 1
IDENTIFIER
26
25
0.020
(0.50)
R
0.021 (0.53)
0.013 (0.33)
0.050
(1.27)
BSC
TOP VIEW
(PINS DOWN)
11
12
0.025 (0.63)
0.015 (0.38)
0.032 (0.81)
0.026 (0.66)
19
18
0.430 (10.92)
0.390 (9.91)
0.040 (1.01)
0.025 (0.64)
0.456 (11.58)
SQ
0.450 (11.43)
0.495 (12.57)
SQ
0.485 (12.32)
0.110 (2.79)
0.085 (2.16)
28–Terminal LCC Package (E-28A)
0.075
(1.91)
REF
0.075 (1.91) REF
TOP VIEW
AA
AA
0.100 (2.54)
0.064 (1.63)
0.458
(11.63)
MAX
SQ
0.300 (7.62) BSC
0.015 (0.38)
MIN
0.150 (3.81) BSC
0.095 (2.41)
0.075 (1.90)
0.028 (0.71)
0.022 (0.56)
28
PRINTED IN U.S.A.
AA
AA
0.458 (11.63)
SQ
0.442 (11.23)
1
BOTTOM
VIEW
0.011 (0.28)
0.007 (0.18)
R TYP
18
0.050
(1.27)
BSC
12
0.055 (1.40)
0.045 (1.14)
0.200
(5.08)
BSC
0.088 (2.24)
0.054 (1.37)
–12–
45°
TYP
REV. B