AD ADG1312YRZ -15 v/12 v quad spst switch Datasheet

±15 V/12 V Quad SPST Switches
ADG1311/ADG1312/ADG1313
33 V supply range
Fully specified at +12 V, ±15 V
130 Ω on resistance
No VL supply required
3 V logic-compatible inputs
Rail-to-rail operation
16-lead TSSOP and 16-lead SOIC
Typical power consumption: <0.03 μW
FUNCTIONAL BLOCK DIAGRAM
S1
IN1
IN1
D1
D1
S2
S2
IN2
D2
ADG1312
APPLICATIONS
ADG1313
S3
IN3
D3
D3
S4
S4
D3
S4
IN4
IN4
D4
Signal switching
Battery-powered systems
Communication systems
Audio/video signal routing
D2
D2
IN3
IN4
S2
S3
S3
IN3
D1
IN2
IN2
ADG1311
S1
S1
IN1
D4
SWITCHES SHOWN FOR A LOGIC 1 INPUT
D4
05676-001
FEATURES
Figure 1.
GENERAL DESCRIPTION
PRODUCT HIGHLIGHTS
The ADG1311/ADG1312/ADG1313 are monolithic CMOS
devices containing four independently selectable switches
designed on a CMOS process.
1.
2.
3.
3 V logic-compatible digital inputs: VIH = 2.0 V, VIL = 0.8 V.
No VL logic power supply required.
16-lead TSSOP and SOIC packages.
The ADG1311/ADG1312/ADG1313 contain four independent
single-pole/single-throw (SPST) switches. The ADG1311 and
ADG1312 differ only in that the digital control logic is inverted.
The ADG1311 switches are turned on with Logic 0 on the appropriate control input, while Logic 1 is required for the ADG1312.
The ADG1313 has two switches with digital control logic similar
to the ADG1311; the logic is inverted on the other two switches.
The ADG1313 exhibits break-before-make switching action for
use in multiplexer applications.
Each switch conducts equally well in both directions when on
and has an input signal range that extends to the supplies. In the
off condition, signal levels up to the supplies are blocked.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
© 2005 Analog Devices, Inc. All rights reserved.
ADG1311/ADG1312/ADG1313
TABLE OF CONTENTS
Features .............................................................................................. 1
Absolute Maximum Ratings ............................................................5
Applications....................................................................................... 1
ESD Caution...................................................................................5
Functional Block Diagram .............................................................. 1
Pin Configuration and Function Descriptions..............................6
General Description ......................................................................... 1
Terminology .......................................................................................7
Product Highlights ........................................................................... 1
Typical Performance Characteristics ..............................................8
Specifications..................................................................................... 3
Test Circuits..................................................................................... 10
Dual Supply ................................................................................... 3
Outline Dimensions ....................................................................... 12
Single Supply ................................................................................. 4
Ordering Guide .......................................................................... 12
REVISION HISTORY
10/05—Revision 0: Initial Version
Rev. 0 | Page 2 of 12
ADG1311/ADG1312/ADG1313
SPECIFICATIONS
DUAL SUPPLY
VDD = 15 V ± 10%, VSS = −15 V± 10%, GND = 0 V, unless otherwise noted.
Table 1.
Parameter
ANALOG SWITCH
Analog Signal Range
On Resistance (RON)
On Resistance Match Between
Channels (∆RON)
25°C
130
200
5
Y Version 1
−40°C to +105°C
VDD to VSS
230
Unit
Test Conditions/Comments
V
Ω typ
Ω max
Ω typ
VS = ±10 V, IS = −1 mA; Figure 10
VDD = +13.5 V, VSS = −13.5 V
VS = ±10 V, IS = −1 mA
10
25
65
Ω max
Ω typ
Ω max
LEAKAGE CURRENTS
Source Off Leakage, IS (Off )
±10
nA typ
VS = ±10 V, VD = ∓10 V; Figure 11
Drain Off Leakage, ID (Off )
±10
nA typ
±10
nA typ
VS = ±10V, VD = ∓10 V; Figure 11
VS = VD = ±10 V; Figure 12
On Resistance Flatness (RFLAT(ON))
Channel On Leakage, ID, IS (On)
DIGITAL INPUTS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current, IINL or IINH
VDD = +16.5 V, VSS = −16.5 V
2.0
0.8
0.005
±0.1
Digital Input Capacitance, CIN
DYNAMIC CHARACTERISTICS 2
tON
tOFF
Break-Before-Make Time Delay, tD
(ADG1313 Only)
Charge Injection
Off Isolation
Channel-to-Channel Crosstalk
−3 dB Bandwidth
CS (Off )
CD (Off )
CD, CS (On)
POWER REQUIREMENTS
IDD
2.5
105
125
40
50
25
180
60
10
2
80
90
600
5
5
10
0.001
1.0
IDD
220
320
ISS
0.001
1.0
ISS
0.001
1.0
1
2
VS = −5 V/0 V/+5 V; IS = −1 mA
Temperature range for Y Version is −40°C to +105°C.
Guaranteed by design, not subject to production test.
Rev. 0 | Page 3 of 12
V min
V max
μA typ
μA max
pF typ
ns typ
ns max
ns typ
ns max
ns typ
ns min
pC typ
dB typ
dB typ
MHz typ
pF typ
pF typ
pF typ
μA typ
μA max
μA typ
μA max
μA typ
μA max
μA typ
μA max
VIN = VINL or VINH
RL = 300 Ω, CL = 35 pF
VS = +10 V; Figure 13
RL = 300 Ω, CL = 35 pF
VS = +10 V; Figure 13
RL = 300 Ω, CL = 35 pF
VS1 = VS2 = 10 V; Figure 14
VS = 0 V, RS = 0 Ω, CL = 1 nF; Figure 15
RL = 50 Ω, CL = 5 pF, f = 1 MHz; Figure 16
RL = 50 Ω, CL = 5 pF, f = 1 MHz; Figure 17
RL = 50 Ω, CL = 5 pF; Figure 18
VDD = +16.5 V, VSS = −16.5 V
Digital inputs = 0 V or VDD
Digital inputs = 5 V
Digital inputs = 0 V or VDD
Digital inputs = 5 V
ADG1311/ADG1312/ADG1313
SINGLE SUPPLY
VDD = 12 V ± 10%, VSS = 0 V, GND = 0 V, unless otherwise noted.
Table 2.
Parameter
ANALOG SWITCH
Analog Signal Range
On Resistance (RON)
On Resistance Match Between
Channels (∆RON)
On Resistance Flatness (RFLAT(ON))
LEAKAGE CURRENTS
Source Off Leakage, IS (Off )
Drain Off Leakage, ID (Off )
Channel On Leakage, ID, IS (On)
DIGITAL INPUTS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current, IINL or IINH
25°C
325
500
10
Y Version 1
−40°C to +105°C
0 V to VDD
520
tOFF
Break-Before-Make Time Delay, tD
(ADG1313 Only)
Charge Injection
Off Isolation
Channel-to-Channel Crosstalk
−3 dB Bandwidth
CS (Off )
CD (Off )
CD, CS (On)
POWER REQUIREMENTS
IDD
2
VS = 0 V − 10 V, IS = −1 mA; Figure 10
VDD = 10.8 V, VSS = 0 V
VS = 0 V − 10 V, IS = −1 mA
±10
±10
±10
nA typ
nA typ
nA typ
2.0
0.8
0.001
3
120
155
45
65
50
210
80
10
2
80
90
500
5
5
10
0.001
220
320
1
V
Ω typ
Ω max
Ω typ
Ω max
Ω typ
1.0
IDD
Test Conditions/Comments
15
65
±0.1
Digital Input Capacitance, CIN
DYNAMIC CHARACTERISTICS 2
tON
Unit
Temperature range for Y Version is −40°C to +105°C.
Guaranteed by design, not subject to production test.
Rev. 0 | Page 4 of 12
V min
V max
μA typ
μA max
pF typ
ns typ
ns max
ns typ
ns max
ns typ
ns min
pC typ
dB typ
dB typ
MHz typ
pF typ
pF typ
pF typ
μA typ
μA max
μA typ
μA max
VS = +3 V/+6 V/+9 V, IS = −1 mA
VDD = 13.2 V, VSS = 0 V
VS = +1 V/+10 V, VD = +10 V/+1 V; Figure 11
VS = +1 V/+10 V, VD = +10 V/+1 V Figure 11
VS = VD = +1 V or +10 V; Figure 12
VIN = VINL or VINH
RL = 300 Ω, CL = 35 pF
VS = 8 V; Figure 13
RL = 300 Ω, CL = 35 pF
VS = 8 V; Figure 13
RL = 300 Ω, CL = 35 pF
VS1 = VS2 = 8 V; Figure 14
VS = 6 V, RS = 0 Ω, CL = 1 nF; Figure 15
RL = 50 Ω, CL = 5 pF, f = 1 MHz; Figure 16
RL = 50 Ω, CL = 5 pF, f = 1 MHz; Figure 17
RL = 50 Ω, CL = 5 pF; Figure 18
VDD = 13.2 V
Digital inputs = 0 V or VDD
Digital inputs = 5 V
ADG1311/ADG1312/ADG1313
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted.
Table 3.
Parameter
VDD to VSS
VDD to GND
VSS to GND
Analog Inputs 1
Digital Inputs1
Peak Current, S or D
Continuous Current per
Channel, S or D
Operating Temperature Range
Automotive
Storage Temperature Range
Junction Temperature
16-Lead TSSOP, θJA Thermal
Impedance (4-layer board)
16-Lead SOIC, θJA Thermal
Impedance
Reflow Soldering Peak
Temperature, Pb free
1
Rating
35 V
−0.3 V to +25 V
+0.3 V to −25 V
VSS − 0.3 V to VDD + 0.3 V or
30 mA, whichever occurs first
GND − 0.3 V to VDD + 0.3 V or
30 mA, whichever occurs first
100 mA (pulsed at 1 ms,
10% duty cycle max)
25 mA
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Table 4. ADG1311/ADG1312 Truth Table
ADG1311 INx
0
1
ADG1312 INx
1
0
Switch Condition
On
Off
Table 5. ADG1313 Truth Table
ADG1313 INx
0
1
−40°C to +105°C
−65°C to +150°C
150°C
112°C/W
Switch 1, 4
Off
On
77°C/W
260°C
Overvoltages at IN, S, or D are clamped by internal diodes. Current should be
limited to the maximum ratings given.
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. 0 | Page 5 of 12
Switch 2, 3
On
Off
ADG1311/ADG1312/ADG1313
IN1
1
16
IN2
D1
2
15
D2
S1
3
14
S2
VSS
4
GND
5
S4
ADG1311/
ADG1312/
ADG1313
13
VDD
12
NC
6
11
S3
D4
7
10
D3
IN4
8
9
IN3
TOP VIEW
NC = NO CONNECT
05676-002
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
Figure 2. SOIC/TSSOP Pin Configuration
Table 6. Pin Function Descriptions
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Mnemonic
IN1
D1
S1
VSS
GND
S4
D4
IN4
IN3
D3
S3
NC
VDD
S2
D2
IN2
Description
Logic Control Input.
Drain Terminal. Can be an input or output.
Source Terminal. Can be an input or output.
Most Negative Power Supply Potential.
Ground (0 V) Reference.
Source Terminal. Can be an input or output.
Drain Terminal. Can be an input or output.
Logic Control Input.
Logic Control Input.
Drain Terminal. Can be an input or output.
Source Terminal. Can be an input or output.
No Connection.
Most Positive Power Supply Potential.
Source Terminal. Can be an input or output.
Drain Terminal. Can be an input or output.
Logic Control Input.
Rev. 0 | Page 6 of 12
ADG1311/ADG1312/ADG1313
TERMINOLOGY
IDD
The positive supply current.
CD, CS (On)
The on switch capacitance, measured with reference to ground.
ISS
The negative supply current.
CIN
The digital input capacitance.
VD (VS)
The analog voltage on Terminal D and Terminal S.
tON
The delay between applying the digital control input and the
output switching on. See Figure 13.
RON
The ohmic resistance between D and S.
RFLAT(ON)
Flatness is defined as the difference between the maximum and
minimum value of on resistance, as measured over the specified
analog signal range.
IS (Off)
The source leakage current with the switch off.
tOFF
The delay between applying the digital control input and the
output switching off. See Figure 13.
Charge Injection
A measure of the glitch impulse transferred from the digital
input to the analog output during switching.
Off Isolation
A measure of unwanted signal coupling through an off switch.
ID (Off)
The drain leakage current with the switch off.
Crosstalk
A measure of unwanted signal that is coupled through from one
channel to another as a result of parasitic capacitance.
ID, IS (On)
The channel leakage current with the switch on.
Bandwidth
The frequency at which the output is attenuated by 3 dB.
VINL
The maximum input voltage for Logic 0.
On Response
The frequency response of the on switch.
VINH
The minimum input voltage for Logic 1.
Insertion Loss
The loss due to the on resistance of the switch.
IINL (IINH)
The input current of the digital input.
CS (Off)
The off switch source capacitance, measured with reference to
ground.
CD (Off)
The off switch drain capacitance, measured with reference to
ground.
Rev. 0 | Page 7 of 12
ADG1311/ADG1312/ADG1313
TYPICAL PERFORMANCE CHARACTERISTICS
200
600
TA = 25°C
180
VDD = 12V
VSS = 0V
500
TA = +85°C
VDD = +15V
VSS = –15V
140
ON RESISTANCE (Ω)
ON RESISTANCE (Ω)
160
120
100
80
60
400
300
200
TA = –40°C
40
TA = +25°C
20
0
–15
–12
–9
–6
–3
0
3
6
9
SOURCE OR DRAIN VOLTAGE (V)
12
0
0
15
Figure 3. On Resistance as a Function of VD (VS) for Dual Supply
4
6
8
SOURCE OR DRAIN VOLTAGE (V)
10
12
200
TA = 25°C
400
180
350
160
12V SS TON
140
300
TIME (ns)
VDD = 12V
VSS = 0V
250
200
150
120
15V DS TON
100
80
12V SS TOFF
60
100
0
0
2
4
6
8
SOURCE OR DRAIN VOLTAGE (V)
10
15V DS TOFF
05676-016
05676-005
40
50
20
0
–40
12
Figure 4. On Resistance as a Function of VD (VS) for Single Supply
–20
0
20
40
60
TEMPERATURE (°C)
80
100
120
Figure 7. TON/TOFF Times vs. Temperature
0
250
VDD = +15V
VSS = –15V
–10
–20
OFF ISOLATION (dB)
200
150
TA = +85°C
100
TA = –40°C
TA = +25°C
VDD = +15V
VSS = –15V
TA = 25°C
–30
–40
–50
–60
–70
–80
50
–10
–5
0
5
SOURCE OR DRAIN VOLTAGE (V)
10
15
05676-017
0
–15
–90
05676-006
ON RESISTANCE (Ω)
2
Figure 6. On Resistance as a Function of VD (VS) for Different
Temperatures, Single Supply
450
ON RESISTANCE (Ω)
05676-007
05676-008
100
–100
–110
10k
100k
1M
10M
FREQUENCY (Hz)
Figure 8. Off Isolation vs. Frequency
Figure 5. On Resistance as a Function of VD (VS) for Different
Temperatures, Dual Supply
Rev. 0 | Page 8 of 12
100M
1G
ADG1311/ADG1312/ADG1313
0
–10
–20
VDD = +15V
VSS = –15V
TA = 25°C
–40
–50
–60
–70
–80
–90
–100
05676-018
CROSSTALK (dB)
–30
–110
–120
10k
100k
1M
FREQUENCY (Hz)
10M
100M
Figure 9. Crosstalk vs. Frequency
Rev. 0 | Page 9 of 12
ADG1311/ADG1312/ADG1313
TEST CIRCUITS
IDS
V1
VD
D
A
VD
NC = NO CONNECT
Figure 11. Test Circuit 2—Off Leakage
VDD
S
NC
A
VS
Figure 10. Test Circuit 1—On Resistance
Figure 12. Test Circuit 3 —On Leakage
VSS
0.1μF
VDD
VSS
S
VIN
ADG1312
50%
50%
VIN
ADG1311
50%
50%
VOUT
D
CL
35pF
RL
300Ω
IN
90%
VOUT
90%
GND
tOFF
tON
05676-023
0.1μF
VS
D
05676-021
RON = V1/IDS
VS
ID (ON)
ID (OFF)
S
A
Figure 13. Test Circuit 4—Switching Times
VDD
VSS
VSS
S1
D1
S2
D2
CL
35pF
RL
300Ω
IN1,
IN2
RL
300Ω
VOUT2
CL
35pF
VOUT1
VOUT1
50%
90%
90%
0V
90%
VOUT2
90%
0V
ADG1313
tD
GND
tD
Figure 14. Test Circuit 5—Break-Before-Make Time Delay
RS
VS
VDD
VSS
VDD
VSS
S
D
VIN
CL
1nF
IN
GND
ADG1312
ON
VOUT
VIN
OFF
ADG1311
VOUT
QINJ = CL × ΔVOUT
Figure 15. Test Circuit 6—Charge Injection
Rev. 0 | Page 10 of 12
ΔVOUT
05676-025
VS2
50%
0V
05676-024
VDD
VS1
VIN
0.1μF
0.1μF
05676-022
IS (OFF)
D
05676-020
S
ADG1311/ADG1312/ADG1313
VSS
VDD
0.1μF
VDD
NETWORK
ANALYZER
VSS
S
S
D
RL
50Ω
GND
VOUT
50Ω
VS
VIN
RL
50Ω
05676-026
GND
OFF ISOLATION = 20 log
VOUT
VS
Figure 16. Test Circuit 7—Off Isolation
RL
50Ω
NETWORK
ANALYZER
D
VIN
VOUT
VSS
IN
VS
NETWORK
ANALYZER
0.1μF
VDD
50Ω
50Ω
IN
VSS
0.1μF
VDD
0.1μF
VSS
VDD
VSS
VOUT WITH SWITCH
VOUT WITHOUT SWITCH
Figure 18. Test Circuit 9—Bandwidth
0.1μF
S1
D2
S2
R
50Ω
VS
VOUT
VS
05676-027
GND
CHANNEL-TO-CHANNEL CROSSTALK = 20 log
INSERTION LOSS = 20 log
Figure 17. Test Circuit 8—Channel-to-Channel Crosstalk
Rev. 0 | Page 11 of 12
VOUT
05676-028
VDD
0.1μF
ADG1311/ADG1312/ADG1313
OUTLINE DIMENSIONS
5.10
5.00
4.90
10.00 (0.3937)
9.80 (0.3858)
16
9
4.50
4.40
4.30
4.00 (0.1575)
3.80 (0.1496)
6.40
BSC
1
8
0.20
0.09
0.30
0.19
COPLANARITY
0.10
8
6.20 (0.2441)
5.80 (0.2283)
1.75 (0.0689)
1.35 (0.0531)
0.50 (0.0197)
× 45°
0.25 (0.0098)
0.25 (0.0098)
0.10 (0.0039)
1.20
MAX
0.65
BSC
9
1
1.27 (0.0500)
BSC
PIN 1
0.15
0.05
16
SEATING
PLANE
COPLANARITY
0.10
0.75
0.60
0.45
8°
0°
8°
0.51 (0.0201) SEATING
0.25 (0.0098) 0° 1.27 (0.0500)
PLANE
0.31 (0.0122)
0.40 (0.0157)
0.17 (0.0067)
COMPLIANT TO JEDEC STANDARDS MS-012-AC
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN
COMPLIANT TO JEDEC STANDARDS MO-153-AB
Figure 20. 16-Lead Standard Small Outline Package [SOIC_N]
Narrow Body
(R-16)
Dimensions shown in millimeters and (inches)
Figure 19. 16-Lead Thin Shrink Small Outline Package [TSSOP]
(RU-16)
Dimensions shown in millimeters
ORDERING GUIDE
Model
ADG1311YRUZ 1
ADG1311YRUZ-REEL71
ADG1311YRZ1
ADG1311YRZ-REEL71
ADG1312YRUZ1
ADG1312YRUZ-REEL71
ADG1312YRZ1
ADG1312YRZ-REEL71
ADG1313YRUZ1
ADG1313YRUZ-REEL71
ADG1313YRZ1
ADG1313YRZ-REEL71
1
Temperature Range
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
Package Description
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Narrow Body Small Outline Package [SOIC_N]
16-Lead Narrow Body Small Outline Package [SOIC_N]
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Narrow Body Small Outline Package [SOIC_N]
16-Lead Narrow Body Small Outline Package [SOIC_N]
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Narrow Body Small Outline Package [SOIC_N]
16-Lead Narrow Body Small Outline Package [SOIC_N]
Z = Pb-free part.
© 2005 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D05676-0-10/05(0)
Rev. 0 | Page 12 of 12
Package Option
RU-16
RU-16
R-16
R-16
RU-16
RU-16
R-16
R-16
RU-16
RU-16
R-16
R-16
Similar pages