TI1 DAC7613 12-bit, voltage output digital-to-analog converter Datasheet

®
DAC7613
DAC
761
3
For most current data sheet and other product
information, visit www.burr-brown.com
12-Bit, Voltage Output
DIGITAL-TO-ANALOG CONVERTER
FEATURES
DESCRIPTION
● LOW POWER: 1.8mW
The DAC7613 is a 12-bit, voltage output digital-toanalog converter with guaranteed 12-bit monotonic
performance over the specified temperature range.
The DAC7613 accepts a 12-bit parallel input data, has
double-buffered DAC input logic and provides a
readback mode of the internal input register. An asynchronous reset clears all registers to a mid-scale code
of 800H or to a zero-scale of 000H. The DAC7613 can
operate from a single +5V supply or from +5V and
–5V supplies.
● UNIPOLAR OR BIPOLAR OPERATION
● SETTLING TIME: 10µs to 0.012%
● 12-BIT LINEARITY AND MONOTONICITY:
–40°C to +85°C
● DATA READBACK
● DOUBLE-BUFFERED DATA INPUTS
● 24-LEAD SSOP PACKAGE
Low power and small size makes the DAC7613 ideal
for data acquisition systems and closed-loop servocontrol. The DAC7613 is available in a plastic
SSOP-24 package, and offers guaranteed specifications over the –40°C to +85°C temperature range.
APPLICATIONS
● PROCESS CONTROL
● CLOSED-LOOP SERVO-CONTROL
● MOTOR CONTROL
● DATA ACQUISITION SYSTEMS
VREFL VREFH
Data I/O
VDD
VSS
12
CS
Input
Register
I/O
Buffer
DAC
Register
VOUT
DAC
TS
R/W
DAC7613
RESET
RESETSEL LOADDAC
GND
International Airport Industrial Park • Mailing Address: PO Box 11400, Tucson, AZ 85734 • Street Address: 6730 S. Tucson Blvd., Tucson, AZ 85706 • Tel: (520) 746-1111
Twx: 910-952-1111 • Internet: http://www.burr-brown.com/ • Cable: BBRCORP • Telex: 066-6491 • FAX: (520) 889-1510 • Immediate Product Info: (800) 548-6132
®
© 1998 Burr-Brown Corporation
SBAS105
PDS-1500B
1
Printed in U.S.A. January, 2000
DAC7613
SPECIFICATION
At TA = –40°C to +85°C, VDD = +5V, VSS = –5V, VREFH = +2.5V, and VREFL = –2.5V, unless otherwise noted.
DAC7613E
PARAMETER
CONDITIONS
ACCURACY
Linearity Error(1)
Differential Linearity Error
Monotonicity
Zero-Scale Error
Zero-Scale Drift
Full-Scale Error
Zero-Scale Error
Zero-Scale Drift
Full-Scale Error
Power Supply Rejection
ANALOG OUTPUT
Voltage Output(3)
Output Current
Load Capacitance
Short-Circuit Current
Short-Circuit Duration
REFERENCE INPUT
VREFH Input Range
VREFL Input Range
VREFL Input Range
DYNAMIC PERFORMANCE
Settling Time(4)
Output Noise Voltage
DIGITAL INPUT/OUTPUT
Logic Family
Logic Levels
VIH
VIL
VOH
VOL
Data Format
POWER SUPPLY REQUIREMENTS
VDD
VSS
IDD
ISS
Power Dissipation
TEMPERATURE RANGE
Specified Performance
VSS = 0V or –5V
VSS = 0V or –5V
TMIN to TMAX
Code = 000H
MIN
TYP
DAC7613EB
MAX
MIN
±2
±1
Code = FFFH
Code = 00AH, VSS = 0V
VSS = 0V
Code = FFFH, VSS = 0V
5
±4
5
±4
±8
10
±8
✻
✻
0
VREFL
–1.25
VREFH
VREFH
+1.25
No Oscillation
VREFL + 1.25
0
–2.5
+2.5
VREFH – 1.25
VREFH – 1.25
5
40
If VSS ≠ 0V
0.7 VDD
–0.3
3.6
0.0
VSS = –5V
VSS = 0V
–40
0.35
–0.45
4
1.8
✻
✻
✻
✻
✻
10
LSB(2)
LSB
Bits
LSB
ppm/°C
LS
LSB
ppm/°C
LSB
ppm/V
✻
✻
✻
✻
✻
✻
✻
✻
✻
V
V
mA
pF
mA
✻
✻
✻
V
V
V
✻
µs
nV/√Hz
✻
✻
✻
✻
V
V
V
V
✻
✻
✻
✻
✻
V
V
mA
mA
mW
mW
✻
°C
✻
VDD + 0.3
0.3 VDD
VDD
0.4
Straight Binary
4.75
–5.25
–0.65
±1
±1
✻
✻
✻
CMOS
IIH ≤ ±10µA
IIL ≤ ±10µA
IOH = –0.8mA
I OL = 1.6mA
✻
✻
✻
100
+5, –15
Indefinite
To ±0.012%
0Hz to 1MHz
UNITS
✻
30
VSS = 0V or –5V
VSS = 0V
VSS = –5V
MAX
✻
12
2
VREFL = 0V, VSS = 0V
VSS = –5V
TYP
5.25
–4.75
0.5
✻
✻
✻
✻
✻
✻
✻
✻
5.75
2.5
+85
✻
✻
✻
✻
✻
NOTES: (1) If VSS = 0V, specification applies at code 00AH and above. (2) LSB means Least Significant Bit, when V REFH equals +2.5V and VREFL equals –2.5V,
then one LSB equals 1.22mV. (3) Ideal output voltage, does not take into account zero or full-scale error. (4) If VSS = –5V, full-scale 5V step. If VSS = 0V, full-scale
positive 2.5V step and negative step from code FFFH to 00AH.
The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes
no responsibility for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject to change
without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant
any BURR-BROWN product for use in life support devices and/or systems.
®
DAC7613
2
ELECTROSTATIC
DISCHARGE SENSITIVITY
ABSOLUTE MAXIMUM RATINGS(1)
VDD to VSS ............................................................................. –0.3V to 11V
VDD to GND .......................................................................... –0.3V to 5.5V
VREFL to VSS .............................................................. –0.3V to (VDD – VSS)
VDD to VREFH ............................................................. –0.3V to (VDD – VSS)
VREFH to VREFL .......................................................... –0.3V to (VDD – VSS)
Digital Input Voltage to GND ................................... –0.3V to VDD + 0.3V
Digital Output Voltage to GND ................................. –0.3V to VDD + 0.3V
Maximum Junction Temperature ................................................... +150°C
Operating Temperature Range ........................................ –40°C to +85°C
Storage Temperature Range ......................................... –65°C to +150°C
Lead Temperature (soldering, 10s) ............................................... +300°C
This integrated circuit can be damaged by ESD. Burr-Brown
recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling
and installation procedures can cause damage.
ESD damage can range from subtle performance degradation
to complete device failure. Precision integrated circuits may
be more susceptible to damage because very small parametric
changes could cause the device not to meet its published
specifications.
NOTE: (1) Stresses above those listed under “Absolute Maximum Ratings”
may cause permanent damage to the device. Exposure to absolute maximum
conditions for extended periods may affect device reliability.
PACKAGE/ORDERING INFORMATION
PRODUCT
MAXIMUM
LINEARITY
ERROR
(LSB)
MAXIMUM
DIFFERENTIAL
LINEARITY ERROR
(LSB)
DAC7613E
PACKAGE
PACKAGE
DRAWING
NUMBER
SPECIFICATION
TEMPERATURE
RANGE
±2
±1
SSOP-24
338
–40°C to +85°C
"
"
"
"
"
"
DAC7613EB
±1
±1
SSOP-24
338
–40°C to +85°C
"
"
"
"
"
"
ORDERING
NUMBER(1)
TRANSPORT
MEDIA
DAC7613E
DAC7613E/1K
Rails
Tape and Reel
DAC7613EB
DAC7613EB/1K
Rails
Tape and Reel
NOTE: (1) Models with a slash (/) are available only in Tape and Reel in the quantities indicated (e.g., /1K indicates 1000 devices per reel). Ordering 1000 pieces
of “DAC7613E/1K” will get a single 1000-piece Tape and Reel.
®
3
DAC7613
PIN CONFIGURATION
PIN DESCRIPTIONS
Top View
PIN
SSOP
DB11 (MSB)
24
1
R/W
LABEL
DESCRIPTION
1
DB11
Data Bit 11, MSB
2
DB10
Data Bit 10
3
DB9
Data Bit 9
4
DB8
Data Bit 8
DB10
2
23
CS
DB9
3
22
RESETSEL
5
DB7
Data Bit 7
DB8
4
21
RESET
6
DB6
Data Bit 6
7
DB5
Data Bit 5
8
DB4
Data Bit 4
DB7
20
5
19
VOUT
9
DB3
Data Bit 3
7
18
VDD
10
DB2
Data Bit 2
8
17
GND
11
DB1
Data Bit 1
12
DB0
Data Bit 0, LSB
13
VREFL
Reference Input Voltage Low. Sets minimum output voltage for the DAC.
DB6
6
DB5
DB4
DAC7613E
DB3
LOADDAC
9
16
VSS
DB2 10
15
VREFH
DB1 11
14
NIC
DB0 (LSB) 12
13
VREFL
®
DAC7613
4
14
NIC
15
VREFH
Not Internally Connected
16
VSS
17
GND
Ground
18
VDD
Positive Power Supply
19
VOUT
20
LOADDAC
The selected DAC register becomes transparent
when LOADDAC is LOW. It is in the latched state
when LOADDAC is HIGH.
21
RESET
Asynchronous Reset Input. Sets the DAC register
to either zero-scale (000H) or mid-scale (800H)
when LOW. RESETSEL determines which code is
active.
22
RESETSEL
When LOW, a LOW on RESET will cause the DAC
register to be set to code 000H. When RESETSEL
is HIGH, a LOW on RESET will set the registers to
code 800H.
Reference Input Voltage High. Sets maximum
output voltage for the DAC.
Negative Analog Supply Voltage, 0V or –5V
nominal.
DAC Voltage Output
23
CS
Chip Select. Active LOW.
24
R/W
Enabled by CS. Controls data read and write from
the input register.
TYPICAL PERFORMANCE CURVES: VSS = 0V
At TA = +25°C, VDD = +5V, VREFH = +2.5V, and VREFL = 0V, representative unit, unless otherwise specified.
LINEARITY ERROR vs CODE
(–40°C and +85°C)
0.50
0.50
0.25
0.25
LE (LSB)
LE (LSB)
LINEARITY ERROR and
DIFFERENTIAL LINEARITY ERROR vs CODE
0.00
–0.25
0.00
–0.25
0.50
0.50
0.25
0.25
LE (LSB)
–0.50
0.00
–0.25
DLE (LSB)
–0.50
000H
200H
400H
600H
800H
–0.25
–40°C
–0.50
000H 200H
A00H C00H E00H FFFH
400H
600H
800H
A00H C00H E00H FFFH
Digital Input Code
Digital Input Code
DIFFERENTIAL LINEARITY ERROR vs CODE
(–40°C and +85°C)
ZERO-SCALE ERROR vs TEMPERATURE
(Code 010H)
0.50
6
0.25
5
0.00
–0.25
+85°C
–0.50
0.50
0.25
0.00
4
3
2
1
0
–1
–0.25
–40°C
–0.50
000H
200H
–2
400H
600H
800H
–40
A00H C00H E00H FFFH
–20
0
20
40
60
80
100
Temperature (°C)
Digital Input Code
FULL-SCALE ERROR vs TEMPERATURE
(Code FFFH)
6
5
Full-Scale Error (LSB)
DLE (LSB)
0.00
Zero-Scale Error (LSB)
DLE (LSB)
+85°C
–0.50
4
3
2
1
0
–1
–2
–40
–20
0
20
40
60
80
100
Temperature (°C)
®
5
DAC7613
TYPICAL PERFORMANCE CURVES: VSS = – 5V
At TA = +25°C, VDD = +5V, VREFH = +2.5V, and VREFL = 0V, representative unit, unless otherwise specified.
0.25
0.25
LE (LSB)
0.50
0.00
–0.25
0.50
0.25
0.25
LE (LSB)
–0.50
0.50
0.00
–0.25
200H
400H
600H
800H
0.00
–0.25
–0.50
000H
A00H C00H E00H FFFH
400H
600H
800H
A00H C00H E00H FFFH
Digital Input Code
DIFFERENTIAL LINEARITY ERROR vs CODE
ZERO-SCALE ERROR vs TEMPERATURE
(Code 000H)
0.50
3.0
0.25
2.5
0.00
–0.25
0.50
0.25
0.00
2.0
1.5
1.0
0.5
0.0
–0.5
–0.25
–1.0
200H
400H
600H
800H
–40
A00H C00H E00H FFFH
–20
0
FULL-SCALE ERROR vs TEMPERATURE
(Code FFFH)
3.0
2.5
2.0
1.5
1.0
0.5
0.0
–0.5
–1.0
–40
–20
0
20
40
Temperature (°C)
®
DAC7613
20
40
Temperature (°C)
Digital Input Code
Full-Scale Error (LSB)
–0.50
000H
200H
Digital Input Code
–0.50
DLE (LSB)
0.00
–0.25
–0.50
–0.50
000H
DLE (LSB)
LINEARITY ERROR vs CODE
0.50
Zero-Scale Error (LSB)
DLE (LSB)
LE (LSB)
LINEARITY ERROR and
DIFFERENTIAL LINEARITY ERROR vs CODE
6
60
80
100
60
80
100
THEORY OF OPERATION
register offers a readback capability. The converter can be
powered from a single +5V supply or a dual ±5V supply.
The device offers a reset function which immediately sets
the DAC output voltage and DAC register to mid-scale
(code 800H) or to zero-scale (code 000H), depending on the
status of the reset selection. See Figures 1 and 2 for the basic
operation of the DAC7613.
The DAC7613 is a 12-bit, voltage output Digital-to-Analog
Converter (DAC). The architecture is a classic R-2R ladder
configuration followed by an operational amplifier that serves
as a buffer. The minimum voltage output (“zero-scale”) and
maximum voltage output (“full-scale”) are set by the external voltage references (VREFL and VREFH, respectively). The
digital input is a 12-bit parallel word and the DAC input
DAC7613E
Data Bus
1
DB11
R/W
24
Read/Write
2
DB10
CS
23
Chip Select
3
DB9
RESETSEL
22
Reset Select
4
DB8
RESET
21
Reset DAC
5
DB7
LOADDAC
20
Load DAC Register
6
DB6
VOUT
19
0V to +2.5V
7
DB5
VDD
18
8
DB4
GND
17
9
DB3
VSS
16
10
DB2
VREFH
15
11
DB1
NIC
14
12
DB0
VREFL
13
0.1µF
1µF
+5V
+
+2.5V
0.1µF
FIGURE 1. Basic Single-Supply Operation of the DAC7613.
DAC7613E
Data Bus
1
DB11
R/W
24
Read/Write
2
DB10
CS
23
Chip Select
3
DB9
RESETSEL
22
Reset Select
4
DB8
RESET
21
Reset DAC
5
DB7
LOADDAC
20
Load DAC Register
6
DB6
VOUT
19
–2.5V to +2.5V
7
DB5
VDD
18
8
DB4
GND
17
9
DB3
VSS
16
10
DB2
VREFH
15
11
DB1
NIC
14
0.1µF
1µF
0.1µF
1µF
+
+
+5V
–5V
+2.5V
0.1µF
12
DB0
VREFL
13
–2.5V
0.1µF
FIGURE 2. Basic Dual-Supply Operation of the DAC7613.
®
7
DAC7613
ANALOG OUTPUTS
The current into the VREFH input depends on the DAC output
voltages and can vary from a few microamps to approximately 0.1 milliamp. The VREFH source will not be required
to sink current, only source it. Bypassing the reference
voltage or voltages with at least a 0.1µF capacitor placed as
close to the DAC7613 package is strongly recommended.
When VSS = –5V (dual supply operation), the output amplifier can swing to within 2.25V of the supply rails, guaranteed over the –40°C to +85°C temperature range. With
VSS = 0V (single-supply operation), the output can swing to
ground. Note that the settling time of the output op amp will
be longer with voltages very near ground. Additionally, care
must be taken when measuring the zero-scale error when
VSS = 0V. Since the output voltage cannot swing below
ground, the output voltage may not change for the first few
digital input codes (000H, 001H, 002H, etc.) if the output
amplifier has a negative offset.
DIGITAL INTERFACE
Table I shows the basic control logic for the DAC7613. Note
that the internal register is level triggered and not edge
triggered. When the appropriate signal is LOW, the register
becomes transparent. When this signal is returned HIGH, the
digital word currently in the register is latched. The first
register (the input register) is triggered via the R/W, and CS
inputs. The second register (the DAC register) is transparent
when LOADDAC input is pulled LOW.
The behavior of the output amplifier can be critical in some
applications. Under short-circuit conditions (DAC output
shorted to ground), the output amplifier can sink a great deal
more current than it can source. See the Specifications table
for more details concerning short-circuit current.
The double-buffered architecture is mainly designed so that
the DAC input register can be written at any time and then
the DAC voltage updated by pulling LOADDAC LOW.
REFERENCE INPUTS
The reference inputs, VREFL and VREFH, can be any voltage
between VSS + 2.25V and VDD – 2.25V provided that VREFH
is at least 1.25V greater than VREFL. The minimum output of
each DAC is equal to VREFL plus a small offset voltage
(essentially, the offset of the output op amp). The maximum
output is equal to VREFH plus a similar offset voltage. Note
that VSS (the negative power supply) must either be
connected to ground or must be in the range of –4.75V to
–5.25V. The voltage on VSS sets several bias points within
the converter. If VSS is not in one of these two configurations, the bias values may be in error and proper operation
of the device is not guaranteed.
DAC
REGISTER
L
Write
Write
Write
H
Write
Hold
Write Input
Read
Hold
Read Input
Hold
Update
Update
H
Hold
Hold
Hold
X
Hold
Reset
Reset
CS
RST
LOADDAC
L
L
H
L
L
H
H
L
H
H
X
H
H
L
X
H
H
X
H
L
MODE
X = Don’t Care.
TABLE I. DAC7613 Control Logic Truth Table.
®
DAC7613
INPUT
REGISTER
R/W
8
DIGITAL TIMING
SYMBOL
Figure 3 and Table II provide detailed timing for the digital
interface of the DAC7613.
DIGITAL INPUT CODING
The DAC7613 input data is in Straight Binary format. The
output voltage is given by the following equation:
V OUT = V REFL +
( V REFH – V REFL ) • N
(1)
4096
where N is the digital input code. This equation does not
include the effects of offset (zero-scale) or gain (full-scale)
errors.
DESCRIPTION
MIN
tRCS
CS LOW for Read
200
ns
tRDS
R/W HIGH to CS LOW
10
ns
0
tRDH
R/W HIGH after CS HIGH
tDZ
CS HIGH to Data Bus in
High Impedance
TYP
MAX
UNITS
ns
100
ns
tCSD
CS LOW to Data Bus Valid
tWCS
CS LOW for Write
50
ns
tWS
R/W LOW to CS LOW
0
ns
100
160
ns
tWH
R/W LOW after CS HIGH
5
ns
tDS
Data Valid to CS LOW
0
ns
tDH
Data Valid after CS HIGH
5
ns
tLWD
LOADDAC LOW
50
ns
RESET LOW
50
ns
tRESET
TABLE II. Timing Specifications (TA = –40°C to +85°C).
tWCS
CS
tWS
tWH
R/W
tRCS
tLWD
CS
tRDH
tRDS
LOADDAC
tDZ
Data Out
tDH
tDS
R/W
Data In
Data Valid
tCSD
tRESET
RESET
Data Output Timing
Digital Input Timing
FIGURE 3. Digital Input and Output Timing.
®
9
DAC7613
PACKAGE OPTION ADDENDUM
www.ti.com
8-Jan-2007
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
DAC7613E
ACTIVE
SSOP
DB
24
DAC7613E/1K
ACTIVE
SSOP
DB
DAC7613E/1KG4
ACTIVE
SSOP
DAC7613EB
ACTIVE
DAC7613EB/1K
60
Lead/Ball Finish
MSL Peak Temp (3)
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
24
1000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
DB
24
1000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
SSOP
DB
24
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
ACTIVE
SSOP
DB
24
1000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
DAC7613EB/1KG4
ACTIVE
SSOP
DB
24
1000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
DAC7613EBG4
ACTIVE
SSOP
DB
24
60
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
DAC7613EG4
ACTIVE
SSOP
DB
24
60
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
60
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Mar-2008
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
Diameter Width
(mm) W1 (mm)
A0 (mm)
B0 (mm)
K0 (mm)
P1
(mm)
W
Pin1
(mm) Quadrant
DAC7613E/1K
SSOP
DB
24
1000
330.0
16.4
8.2
8.8
2.5
12.0
16.0
Q1
DAC7613EB/1K
SSOP
DB
24
1000
330.0
16.4
8.2
8.8
2.5
12.0
16.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Mar-2008
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
DAC7613E/1K
SSOP
DB
24
1000
375.0
340.0
57.0
DAC7613EB/1K
SSOP
DB
24
1000
375.0
340.0
57.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Data Converters
DSP
Clocks and Timers
Interface
Logic
Power Mgmt
Microcontrollers
RFID
RF/IF and ZigBee® Solutions
amplifier.ti.com
dataconverter.ti.com
dsp.ti.com
www.ti.com/clocks
interface.ti.com
logic.ti.com
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/lprf
Applications
Audio
Automotive
Broadband
Digital Control
Medical
Military
Optical Networking
Security
Telephony
Video & Imaging
Wireless
www.ti.com/audio
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/medical
www.ti.com/military
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2008, Texas Instruments Incorporated
Similar pages