Click on Series name for product info on aimtec.com Series AM1LR-NZ 1 Watt | DC-DC Converter FEATURES: • Regulated output • Continuous short circuit protection • Efficiency up to 75% • Operating temperature: -40oC to +85 oC • • • Isolation Voltage of 1500 & 3000VDC Small SMD package Universal industry pinout Models Single output Model AM1LR-0503S-NZ AM1LR-0505S-NZ AM1LR-0512S-NZ AM1LR-0515S-NZ AM1LR-1205S-NZ AM1LR-1212S-NZ AM1LR-1215S-NZ AM1LR-2405S-NZ AM1LR-2412S-NZ AM1LR-2415S-NZ Input Voltage (V) Output Voltage (V) Output Current (mA) Isolation (VDC) Max Capacitive Load (µF) Efficiency (%) 4.75-5.25 4.75-5.25 4.75-5.25 4.75-5.25 11.4-12.6 11.4-12.6 11.6-12.6 22.8-25.2 22.8-25.2 22.8-25.2 3.3 5 12 15 5 12 15 5 12 15 243 200 84 67 200 84 67 200 84 67 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 220 220 220 220 220 220 220 220 220 220 58 72 73 74 73 73 75 73 73 74 AM1LR-0503SH30-NZ 4.75-5.25 3.3 243 3000 220 58 AM1LR-0505SH30-NZ 4.75-5.25 5 200 3000 220 72 AM1LR-0512SH30-NZ 4.75-5.25 12 83 3000 220 73 AM1LR-0515SH30-NZ 4.75-5.25 15 67 3000 220 74 AM1LR-1205SH30-NZ 11.4-12.6 5 200 3000 220 73 AM1LR-1212SH30-NZ 11.4-12.6 12 83 3000 220 73 AM1LR-2405SH30-NZ 22.8-25.2 5 200 3000 220 73 NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. Input Specifications Parameters Voltage Range Absolute Max Input Voltage (1 sec max) Nominal Typical 5 12 24 5 Vin 12 Vin 24 Vin 4.75-5.25 11.4-12.6 22.8-25.2 Filter Quiescent Current 5 12 24 Input Reflected Ripple current Maximum Units VDC 9 18 30 Capacitor 15 10 7 15 VDC mA mA Isolation Specifications Parameters Tested I/O Voltage Resistance Capacitance www.aimtec.com F 051e R12 Conditions 60 sec, <1mA 500VDC Typical >1000 20 Tel: +1 514 620 2722 1 of 3 Rated Units 1500 & 3000 VDC MOhm pF Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM1LR-NZ 1 Watt | DC-DC Converter Output Specifications Parameters Voltage Accuracy Short Circuit Protection Short Circuit Restart Line Voltage Regulation Load Voltage Regulation Temperature Coefficient Ripple & Noise Conditions Typical 100% load (see tolerance chart) Maximum ±3 Continuous Auto-Recovery ±0.25 ±3 ±2 For ±1% of Vin (10% - 100% Load) 3.3V (10% - 100% Load) Other outputs 100% load Units % % of Vin % ±0.03 50 o %/ C mV p-p General Specifications Parameters Switching frequency Operating temperature Storage temperature Maximum Case temperature Cooling Storage Humidity Case material Weight Dimensions (L x W x H) MTBF Maximum soldering temperature Maximum case temperature Conditions Typical Maximum Units 100% load With derating above +71 100 300 KHz o C o C o C -40 to +85 -55 to +125 95 Free air convection Non Condensing 95 Epoxy resin (UL94-V0) 2 0.60 x 0.44 x 0.28inches 15.24 x 11.20 x 7.25mm o >3,500,000 hrs (MIL-HDBK -217F, Ground Benign, t=+25 C)hours 1.5mm from case for 10 sec 300 130 Pin Out Specifications % RH g o C C o Dimensions Front View Pin Dual Output Models 1 2 3 4 5 6 7 8 9 10 -V Input +V Input No Pin -V Output -V Output No Pin +V Output No Pin No Pin N.C. 7.62 (0.30) Side View 7.00 (0.28) 0.25 (0.01) 0º~5º angle 1.50 (0.06) Top View 15.2 (0.60) 7.62 (0.30) All dimensions are in mm (inch) All Pins are on a 2.54mm (0.10inch) pitch with tolerance of ±0.25mm (0.01inch) 11.20 8.40 (0.44) (0.33) 1 2.54 (0.10) www.aimtec.com F 051e R12 0.50 (0.02) Tel: +1 514 620 2722 2 of 3 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM1LR-NZ 1 Watt | DC-DC Converter Derating Free Air Convection Input Reflected Ripple Current Test Circuit 71º C Output Power (%) 100 80 L1 (4.7 µh) Vin+ Safe Operating Area 60 Test Point Vo+ + 40 C1 (220 µf) 20 Vin- 0 - 40 Aimtec DC-DC Converter - 20 0 20 40 60 80 85 Vo- - 100 RL (Full Load) * Tested at full load, and nominal input Ambient Temperature º C EMI Recommended Circuit (Class B) LDM 6.8µH C1 4.7µF/ 50V Output Capacitor (C2) +V output +V input DC/DC Converter -V input C2 Vout (VDC) Load 3.3 & 5 12 15 C2 (µF) 10 2.2 1 -V output NOTE: 1.Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified.5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com. www.aimtec.com F 051e R12 Tel: +1 514 620 2722 3 of 3 Toll free: + 1 888 9 AIMTEC (924 6832) North America only