Optoway GBB-7500G 1 *********************************************************************************************************************************************************************** GBB-7500G (RoHS Compliant) 1550 nm TX / 1310 nm RX , 5V / 1.25 Gbps Multi-Mode WDM Gigabit Interface Converter (GBIC) ********************************************************************************************************************************************************************** FEATURES DESCRIPTION l l l l The GBB-7500G series 1-fiber multi-mode optical transceivers meet the Gigabit Interface Converter (GBIC) specification Rev. 5.5. It satisfies the optical interface specifications defined in IEEE 802.3ah 1000BASE BX by using 1550 nm transmitter and 1310 nm receiver. The transmitter section uses a multiple quantum well laser and is a class 1 laser compliant according to International Safety Standard IEC 60825. The receiver section uses an integrated 1310 nm detector preamplifier (IDP) mounted in an optical header and a limiting post-amplifier IC. A PECL input / output logic interface is used. TTL RX-LOS output simplifies interface to external circuitry. A 20-pin SCA-2 host connector is used to connect the converter to the host system. l l l l l l l l l l l 1-Fiber MM Gigabit Interface Converter (GBIC) Compliant with GBIC Specification Rev. 5.5 Compliant with IEEE-802.3ah 1000BASE Compliant with Fibre Channel FC-PH-2 for 100-M5-SN-1 and 100-M6-SN-1 Hot Pluggable Module with SC Connector 1550 nm LD Transmitter 1310 nm Receiver 500 m links with 62.5/125 µm MMF Cables 500 m links with 50/125 µm MMF Cables SCA-2 Host Connector Single +5 V Power Supply RoHS Compliant Differential PECL Inputs and Outputs TTL RX-LOS Output Class 1 Laser International Safety Standard IEC 60825 Compliant APPLICATIONS l WDM Gigabit Ethernet Links l SONET/SDH Equipment Interconnect l Fibre Channel Links LASER SAFETY This multi-mode transceiver is a Class 1 laser product. It complies with IEC 60825 and FDA 21 CFR 1040.10 and 1040.11. The transceiver must be operated within the specified temperature and voltage limits. The optical ports of the module shall be terminated with an optical connector or with a dust plug. ORDER INFORMATION P/No. GBB-7500G Bit Rate (Gb/s) 1.25 Distance (m) 0 to 500 TX (nm) 1550 RX (nm) 1310 Package SC GBIC Temp (oC) 0 to 70 TX Power (dBm) -4 to -10 RX Sens. (dBm) -17 RoHS Compliant Yes Absolute Maximum Ratings Parameter Storage Temperature Operating Case Temperature Power Supply Voltage Input Voltage Relative Humidity Symbol Tstg Topr Vcc --- Min -40 -5 -0.5 -0.5 Max 85 70 6 Vcc Units o C o C V V RH 5 95 % Min 4.75 Typ 5 200 Max 5.25 250 70 Notes Recommended Operating Conditions Parameter Power Supply Voltage Power Supply Current Operating Case Temperature Data Rate Symbol Vcc ITX + IRX Topr 0 1000 1250 Units V mA o C Mb/s ********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: [email protected] http: // www.optoway.com.tw 12/1/2005 V2.0 Optoway GBB-7500G 2 ********************************************************************************************************************************************************************** Transmitter Specifications (0 oC < Topr < 70 oC, 4.75V < Vcc < 5.25V) Parameter Optical Optical Transmit Power Output Center Wavelength Output Spectrum Width Extinction Ratio Optical Rise Time Optical Fall Time Relative Intensity Noise Total Jitter Max. Po at TX-Disable Asserted Electrical Differential Input Voltage Transmit Fault Load Transmit Fault Output-Low Transmit Fault Output-High TX-Disable Input - Low TX-Disable Input - High TX-Disable Assert Time TX-Disable Negate Time Time to initialize, includes reset of TX-FAULT TX FAULT from fault to assertion TX-Disable time to start reset Symbol Min Typ Max Units Notes Po λ ∆λ ER tr tf RIN TJ -10 1480 --- -4 1580 5 1 0.26 0.26 -120 227 -35 dBm nm nm dB ns ns dB/Hz ps dBm VIH - VIL TX-FAULTLOAD VTX-FAULT-L VTX-FAULT-H V TX-DISABLE-L V TX-DISABLE-H t_off t-on t-int 0.65 4.7 0.0 Vcc – 0.5 0 2.0 2.0 10 0.5 Vcc + 0.3 0.8 Vcc + 0.3 10 1 300 Vp-p kΩ V V V V µs ms ms 100 µs 9 t-fault t-reset RMS (σ) 20% to 80% value 20% to 80% value 2 3 µs 10 Notes: 1. Output power is power coupled into a 9/125 µm single mode fiber. 2. Measured with a 27-1 PRBS. 3. Pull-up resistor on host Vcc. Receiver Specifications (0oC < Topr < 70oC, 4.75 V < Vcc < 5.25V) Parameter Optical Sensitivity Maximum Input Power Signal detect – Hysteresis Wavelength of Operation Optical Return Loss RX-LOS – Asserted RX-LOS – Deasserted Electrical Differential Output Voltage Data Output Rise Time Data Output Fall Time RX-LOS of Light Load RX-LOS Output Voltage --- Low RX-LOS Outpu Voltage --- High RX-LOS Assert Time (off to on) RX-LOS Deassert Time (on to off) Symbol Min Typ Max Units Notes --Pin ---3 1.0 1260 12 ---31 --- -17 --- 4 4 -17 --- dBm dBm dB nm dB dBm dBm 2.0 0.35 0.35 10 0.5 Vcc 100 100 Vp-p ns ns kΩ V V µs µs ORL Pa Pd VOH - VOL TrRX-DAT TfRX-DAT RX-LOSLOAD VRX-LOS-L VRX-LOS-H TA,RX-LOS TD,RX-LOS --1360 ----- 0.37 4.7 0 2.4 5 Transition: low to high Transition: high to low 6 Notes: 4. Minimum sensitivity and saturation levels at BER=1E-12 for a 2 7-1 PRBS. 5. At least 30 dB optical isolation for the wavelength 1480 to 1580 nm. 6. Pull-up resistor on host Vcc. *********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: [email protected] http: // www.optoway.com.tw 12/1/2005 V2.0 Optoway GBB-7500G 3 ********************************************************************************************************************************************************************** PIN ASSIGNMENT PIN Signal Name Sequence Description Receiver Loss of Signal, logic high, open collector compatible, 4.7K to 10K ohm pull-up to VCCT on host Receiver Ground Receiver Ground TTL Low SCL Serial Clock Signal SDA Serial Data Signal Transmitter Disable, logic high, open collector compatible Transmitter Ground Transmitter Ground Transmitter Fault, logic high, open collector compatible, 4.7K to 10K ohm pull-up to V CCT on GBIC Receiver Ground Receiver Data Bar, Differential PECL, AC coupled Receiver Data, Differential PECL, AC coupled Receiver Ground Receiver +5V Supply Transmitter +5V Supply Transmitter Ground Transmitter Data, Differential PECL, AC coupled Transmitter Data Bar, Differential PECL, AC coupled Transmitter Ground 1 RX-LOS 2 2 3 4 5 6 7 8 9 10 RGND RGND MOD-DEF(0) MOD-DEF(1) MOD-DEF(2) TX-DIABLE TGND TGND TX-FAULT 2 2 2 2 2 2 2 2 2 11 12 13 14 15 16 17 18 19 20 RGND -RX-DAT +RX-DAT RGND VCCR VCCT TGND +TX-DAT -TX-DAT TGND 1 1 1 1 2 2 1 1 1 1 A sequence value of 1 indicates that the signal is in the first group to engage during plugging of a module. A sequence value of 2 indicates that the signal is the second and last group. The two guide pins on the connector are electrically connected to the transceiver circuit ground. These two guide pins make contact with circuit prior to sequence 1 signals. Module Definition Module Definition 4 MOD-DEF(0) PIN 4 MOD-DEF (1) PIN 5 MOD-DEF (2) PIN 6 Interpretation by Host TTL Low SCL SDA Serial module definition protocol Module Definition 4 specifies a serial definition protocol. For this definition, upon power up, MOD-DEF(1:2) appear as no connector (NC) and MOD-DEF(0) is TTL LOW. When the host system detects this condition, it activates the serial protocol. The protocol uses the 2-wire serial CMOS E 2PROM protocol of the ATMEL AT24C01A/02/04 family of components. *********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: [email protected] http: // www.optoway.com.tw 12/1/2005 V2.0 Optoway GBB-7500G 4 ********************************************************************************************************************************************************************** PACKAGE DIAGRAM Units in mm Note: Specifications subject to change without notice. *********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: [email protected] http: // www.optoway.com.tw 12/1/2005 V2.0