NSC DS55451 Dual peripheral driver Datasheet

DS55451/2/3/4, DS75451/2/3/4 Series
Dual Peripheral Drivers
General Description
Features
The DS7545X series of dual peripheral drivers is a family of
versatile devices designed for use in systems that use TTL
logic. Typical applications include high speed logic buffers,
power drivers, relay drivers, lamp drivers, MOS drivers, bus
drivers and memory drivers.
The DS55451/DS75451, DS55452/DS75452, DS55453/
DS75453 and DS55454/DS75454 are dual peripheral AND,
NAND, OR and NOR drivers, respectively, (positive logic)
with the output of the logic gates internally connected to the
bases of the NPN output transistors.
Y
Y
Y
Y
Y
Y
Y
Y
300 mA output current capability
High voltage outputs
No output latch-up at 20V
High speed switching
Choice of logic function
TTL compatible diode-clamped inputs
Standard supply voltages
Replaces TI ‘‘A’’ and ‘‘B’’ series
Connection Diagrams (Dual-In-Line and Metal Can Packages)
TL/F/5824–2
TL/F/5824 – 3
TL/F/5824 – 4
TL/F/5824 – 5
Top View
Order Number DS55451J-8,
DS75451M or DS75451N
Top View
Order Number DS55452J-8,
DS75452M or DS75452N
Top View
Order Number DS55453J-8,
DS75453M or DS75453N
Top View
Order Number DS55454J-8,
DS75454M or DS75454N
See NS Package Numbers J08A, M08A* or N08E
*See Note 5 and Appendix E regarding S.O. package power dissipation constraints.
TL/F/5824 – 7
TL/F/5824–6
Top View
Top View
Order Number DS55451H
Order Number DS55452H
TL/F/5824 – 8
Top View
(Pin 4 is in Electrical Contact with the Case)
Order Number DS55453H
See NS Package Number H08C
C1995 National Semiconductor Corporation
TL/F/5824
RRD-B30M105/Printed in U. S. A.
DS55451/2/3/4, DS75451/2/3/4 Series Dual Peripheral Drivers
February 1995
Storage Temperature Range
Absolute Maximum Ratings (Note 1)
Supply Voltage, (VCC) (Note 2)
Input Voltage
Inter-Emitter Voltage (Note 3)
Output Voltage (Note 4)
DS55451/DS75451, DS55452/DS75452,
DS55453/DS75453, DS55454/DS75454
Output Current (Note 5)
DS55451/DS75451, DS55452/DS75452,
DS55453/DS75453, DS55454/DS75454
DS75451/2/3/4 Maximum Power (Note 5)
Dissipation ² at 25§ C
Cavity Package
Molded DIP Package
TO-5 Package
SO Package
b 65§ C to a 150§ C
260§ C
Lead Temperature (Soldering, 4 sec.)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales
Office/Distributors for availability and specifications.
Operating Conditions
7.0V
5.5V
5.5V
Supply Voltage, (VCC)
DS5545X
DS7545X
Temperature, (TA)
DS5545X
DS7545X
30V
²
300 mA
Min
Max
Units
4.5
4.75
5.5
5.25
V
V
b 55
a 125
a 70
§C
§C
0
Derate cavity package 7.3 mW/§ C above 25§ C; derate molded package
7.7 mW/§ C above 25§ C; derate TO-5 package 5.1 mW/§ C above 25§ C;
derate SO package 7.56 mW/§ C above 25§ C.
1090 mW
957 mW
760 mW
632 mW
Electrical Characteristics
DS55451/DS75451, DS55452/DS75452, DS55453/DS75453, DS55454/DS75454 (Notes 6 and 7)
Symbol
Parameter
Conditions
High-Level Input Voltage
VIL
Low-Level Input Voltage
VI
Input Clamp Voltage
VCC e Min, II e b12 mA
VOL
Low-Level Output Voltage
VCC e Min,
(Figure 7)
VIL e 0.8V
VIH e 2V
IOL e 100 mA
IOL e 100 mA
IOL e 300 mA
High-Level Output Current
VCC e Min,
(Figure 7)
VOH e 30V VIH e 2V
VIL e 0.8V
II
Input Current at Maximum
Input Voltage
VCC e Max, VI e 5.5V, (Figure 9)
IIH
High-Level Input Current
VCC e Max, VI e 2.4V, (Figure 9)
IIL
Low-Level Input Current
VCC e Max, VI e 0.4V, (Figure 8)
ICCH
Supply Current, Outputs High VCC e Max, VI e 5V
(Figure 10)
VI e 0V
ICCL
Max
2
IOL e 300 mA
IOH
Min Typ
(Figure 7)
VIH
Units
V
0.8
V
b 1.5
V
DS55451, DS55453
0.25
0.5
V
DS75451, DS75453
0.25
0.4
V
DS55451, DS55453
0.5
0.8
V
DS75451, DS75453
0.5
0.7
V
DS55452, DS55454
0.25
0.5
V
DS75452, DS75454
0.25
0.4
V
DS55452, DS55454
0.5
0.8
V
DS75452, DS75454
0.5
0.7
V
DS55451, DS55453
300
mA
DS75451, DS75453
100
mA
DS55452, DS55454
300
mA
DS75452, DS75454
100
mA
1
mA
40
mA
b1
b 1.6
mA
DS55451/DS75451
7
11
mA
DS55452/DS75452
11
14
mA
VI e 5V
DS55453/DS75453
8
11
mA
VI e 0V
DS55454/DS75454
13
17
mA
Supply Current, Outputs Low VCC e Max, VI e 0V
(Figure 10)
VI e 5V
DS55451/DS75451
52
65
mA
DS55452/DS75452
56
71
mA
VI e 0V
DS55453/DS75453
54
68
mA
VI e 5V
DS55454/DS75454
61
79
mA
2
Switching Characteristics
DS55451/DS75451, DS55452/DS75452, DS55453/DS75453, DS55454/DS75454 (VCC e 5V, TA e 25§ C)
Symbol
tPLH
tPHL
Parameter
Propagation Delay Time, Low-to-High
Level Output
Propagation Delay Time, High-to-Low
Level Output
Conditions
CL e 15 pF, RL e 50X,
IO & 200 mA, (Figure 14)
CL e 15 pF, RL e 50X,
IO & 200 mA, (Figure 14)
Typ
Max
Units
DS55451/DS75451
Min
18
25
ns
DS55452/DS75452
26
35
ns
DS55453/DS75453
18
25
ns
DS55454/DS75454
27
35
ns
DS55451/DS75451
18
25
ns
DS55452/DS75452
24
35
ns
DS55453/DS75453
16
25
ns
DS55454/DS75454
24
35
ns
tTLH
Transition Time, Low-to-High Level
Output
CL e 15 pF, RL e 50X, IO & 200mA,
(Figure 14)
5
8
ns
tTHL
Transition Time, High-to-Low Level
Output
CL e 15 pF, RL e 50X, IO & 200 mA,
(Figure 14)
7
12
ns
VOH
High-Level Output Voltage after
Switching
VS e 20V, IO & 300 mA, (Figure 15)
VS b 6.5
mV
Note 1: ‘‘Absolute Maximum Ratings’’ are those values beyond which the safety of the device cannot be guaranteed. Except for ‘‘Operating Temperature Range’’
they are not meant to imply that the devices should be operated at these limits. The table of ‘‘Electrical Characteristics’’ provides conditions for actual device
operation.
Note 2: Voltage values are with respect to network ground terminal unless otherwise specified.
Note 3: The voltage between two emitters of a multiple-emitter transistor.
Note 4: The maximum voltage which should be applied to any output when it is in the ‘‘OFF’’ state.
Note 5: Both halves of these dual circuits may conduct rated current simultaneously; however, power dissipation averaged over a short time interval must fall within
the continuous dissipation rating.
Note 6: Unless otherwise specified min/max limits apply across the b 55§ C to a 125§ C temperature range for the DS55450 series and across the 0§ C to a 70§ C
range for the DS7545X series. All typicals are given for VCC e a 5V and TA e 25§ C.
Note 7: All currents into device pins shown as positive, out of device pins as negative, all voltages referenced to ground unless otherwise noted. All values shown
as max or min on absolute value basis.
3
Truth Tables (H e high level, L e low level)
DS55453/DS75453
DS55451/DS75451
A
B
Y
A
B
Y
L
L
H
H
L
H
L
H
L (ON State)
L (ON State)
L (ON State)
H (OFF State)
L
L
H
H
L
H
L
H
L (ON State)
H (OFF State)
H (OFF State)
H (OFF State)
DS55452/DS75452
DS55454/DS75454
A
B
Y
A
B
Y
L
L
H
H
L
H
L
H
H (OFF State)
H (OFF State)
H (OFF State)
L (ON State)
L
L
H
H
L
H
L
H
H (OFF State)
L (ON State)
L (ON State)
L (ON State)
Schematic Diagrams
DS55451/DS75451
DS55453/DS75453
TL/F/5824 – 13
TL/F/5824–11
Resistor values shown are nominal.
Resistor values shown are nominal.
DS55452/DS75452
DS55454/DS75454
TL/F/5824–12
TL/F/5824 – 14
Resistor values shown are nominal.
Resistor values shown are nominal.
4
DC Test Circuits
TL/F/5824–15
TL/F/5824 – 17
TL/F/5824 – 16
Both inputs are tested simultaneously.
FIGURE 1. VIH, VOL
Each input is tested separately.
Each input is tested separately.
FIGURE 2. VIL, VOH
FIGURE 3. VI, IIL
TL/F/5824–18
TL/F/5824 – 19
Each input is tested separately.
Each input is tested separately.
FIGURE 4. II, IIH
FIGURE 5. IOS
FIGURE 6. ICCH, ICCL
Circuit
Input
Under
Test
DS55451
DS55452
DS55453
DS55454
TL/F/5824 – 21
TL/F/5824 – 20
Both gates are tested simultaneously.
Output
Other
Input
Apply
VIH
VIH
VOH
IOH
VIL
VCC
IOL
VOL
Measure
VIH
VIH
IOL
VOL
VIL
VCC
VOH
IOH
VIH
Gnd
VOH
IOH
VIL
VIL
IOL
VOH
VIH
Gnd
IOL
VOL
VIL
VIL
VOH
IOH
FIGURE 7. VIH, VIL, IOH, VOL
Note A: Each input is tested separately.
Note B: When testing DS55453/DS75453,
DS55454/DS75454, input not
under test is grounded.
For all other circuits it is at 4.5V.
TL/F/5824 – 22
Each input is tested separately.
Both gates are tested simultaneously.
TL/F/5824 – 23
FIGURE 9. II, IIH
FIGURE 8. VI, VIL
Both gates are tested simultaneously.
TL/F/5824 – 24
FIGURE 10. ICCH, ICCL for AND, NAND Circuits
TL/F/5824 – 25
FIGURE 11. ICCH, ICCL for OR, NOR Circuits
5
AC Test Circuits and Switching Time Waveforms
TL/F/5824 – 26
TL/F/5824 – 27
Note 1: The pulse generator has the following characteristics: PRR e 1 MHz, ZOUT & 50X.
Note 2: CL includes probe and jig capacitance.
FIGURE 12. Propagation Delay Times, Each Gate
TL/F/5824 – 28
TL/F/5824 – 29
Note 1: The pulse generator has the following characteristics: duty cycle s 1%, ZOUT & 50X.
Note 2: CL includes probe and jig capacitance.
FIGURE 13. Switching Times, Each Transistor
6
AC Test Circuits and Switching Time Waveforms (Continued)
TL/F/5824 – 30
Note 1: The pulse generator has the following characteristics: PRR e 1.0 MHz, ZOUT & 50X.
Note 2: CL includes probe and jig capacitance.
FIGURE 14. Switching Times of Complete Drivers
7
TL/F/5824 – 31
AC Test Circuits and Switching Time Waveforms (Continued)
TL/F/5824 – 32
TL/F/5824 – 33
Note 1: The pulse generator has the following characteristics: PRR e 12.5 kHz, ZOUT & 50X.
Note 2: CL includes probe and jig capacitance.
FIGURE 15. Latch-UP Test of Complete Drivers
Typical Performance Characteristics
TL/F/5824 – 37
FIGURE 16. Transistor Collector-Emitter Saturation Voltage vs Collector Current
8
Typical Applications
TL/F/5824 – 46
*Optional keep-alive resistors maintain off-state lamp current at & 10% to reduce surge current.
FIGURE 17. Dual Lamp or Relay Driver
TL/F/5824 – 47
FIGURE 18. Complementary Driver
9
Typical Applications (Continued)
TL/F/5824 – 48
FIGURE 19. TTL or DTL Positive Logic-Level Detector
TL/F/5824 – 49
*The two input resistors must be adjusted for the level of MOS input.
FIGURE 20. MOS Negative Logic-Level Detector
TL/F/5824 – 50
FIGURE 21. Logic Signal Comparator
10
Typical Applications (Continued)
TL/F/5824 – 51
*If inputs are unused, they should be connected to a 5V through a 1k resistor.
TL/F/5824 – 52
Low output occurs only when inputs are low simultaneously.
FIGURE 22. In-Phase Detector
TL/F/5824 – 53
FIGURE 23. Multifunction Logic-Signal Comparator
11
Typical Applications (Continued)
TL/F/5824 – 54
FIGURE 24. Alarm Detector
12
13
Physical Dimensions inches (millimeters)
Metal Can Package (H)
Order Number DS55451H, DS55452H or DS55453H,
NS Package Number H08C
Ceramic Dual-In-Line Package (J)
Order Number DS55451J-8, DS55452J-8,
DS55453J-8 or DS55454J-8
NS Package Number J08A
14
Physical Dimensions inches (millimeters) (Continued)
SO Package (M)
Order Number DS75451M, DS75452M, DS75453M or DS75454M
NS Package Number M08A
Molded Dual-In-Line Package (N)
Order Number DS75451N, DS75452N, DS75453N, DS75454N
NS Package Number N08E
15
DS55451/2/3/4, DS75451/2/3/4 Series Dual Peripheral Drivers
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL
SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and whose
failure to perform, when properly used in accordance
with instructions for use provided in the labeling, can
be reasonably expected to result in a significant injury
to the user.
National Semiconductor
Corporation
1111 West Bardin Road
Arlington, TX 76017
Tel: 1(800) 272-9959
Fax: 1(800) 737-7018
2. A critical component is any component of a life
support device or system whose failure to perform can
be reasonably expected to cause the failure of the life
support device or system, or to affect its safety or
effectiveness.
National Semiconductor
Europe
Fax: (a49) 0-180-530 85 86
Email: cnjwge @ tevm2.nsc.com
Deutsch Tel: (a49) 0-180-530 85 85
English Tel: (a49) 0-180-532 78 32
Fran3ais Tel: (a49) 0-180-532 93 58
Italiano Tel: (a49) 0-180-534 16 80
National Semiconductor
Hong Kong Ltd.
13th Floor, Straight Block,
Ocean Centre, 5 Canton Rd.
Tsimshatsui, Kowloon
Hong Kong
Tel: (852) 2737-1600
Fax: (852) 2736-9960
National Semiconductor
Japan Ltd.
Tel: 81-043-299-2309
Fax: 81-043-299-2408
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.