AD AD7328BRUZ 8-channel, software-selectable, true bipolar input, 12-bit plus sign adc Datasheet

FEATURES
FUNCTIONAL BLOCK DIAGRAM
12-bit plus sign SAR ADC
True bipolar input ranges
Software-selectable input ranges
±10 V, ±5 V, ±2.5 V, 0 V to +10 V
1 MSPS throughput rate
8 analog input channels with channel sequencer
Single-ended, true differential, and pseudo differential
analog input capability
High analog input impedance
Low power: 21 mW
Temperature indicator
Full power signal bandwidth: 22 MHz
Internal 2.5 V reference
High speed serial interface
Power-down modes
20-lead TSSOP package
iCMOS process technology
REFIN/OUT
VDD
AD7328
VIN0
2.5V
VREF
VIN1
VIN2
VIN3
VIN4
VIN5
VIN6
VIN7
I/P
MUX
T/H
DOUT
CONTROL LOGIC
AND REGISTERS
CHANNEL
SEQUENCER
AGND
DGND
VSS
Figure 1.
1.
Rev. C
CS
VDRIVE
The AD7328 is an 8-channel, 12-bit plus sign successive
approximation ADC designed on the iCMOS™ (industrial
CMOS) process. iCMOS is a process combining high voltage
silicon with submicron CMOS and complementary bipolar
technologies. It enables the development of a wide range of high
performance analog ICs capable of 33 V operation in a footprint
that no previous generation of high voltage parts could achieve.
Unlike analog ICs using conventional CMOS processes, iCMOS
components can accept bipolar input signals while providing
increased performance, dramatically reduced power consumption,
and reduced package size.
The ADC contains a 2.5 V internal reference. The AD7328 also
allows for external reference operation. If a 3 V reference is applied
to the REFIN/OUT pin, the AD7328 can accept a true bipolar
±12 V analog input. Minimum ±12 V VDD and VSS supplies are
required for the ±12 V input range. The ADC has a high speed
serial interface that can operate at throughput rates up to 1 MSPS.
SCLK
DIN
PRODUCT HIGHLIGHTS
The AD7328 can accept true bipolar analog input signals. The
AD7328 has four software-selectable input ranges: ±10 V, ±5 V,
±2.5 V, and 0 V to +10 V. Each analog input channel can be
independently programmed to one of the four input ranges. The
analog input channels on the AD7328 can be programmed to be
single-ended, true differential, or pseudo differential.
13-BIT
SUCCESSIVE
APPROXIMATION
ADC
TEMPERATURE
INDICATOR
GENERAL DESCRIPTION
1
VCC
04852-001
Data Sheet
8-Channel, Software-Selectable,
True Bipolar Input, 12-Bit Plus Sign ADC
AD7328
2.
3.
4.
5.
The AD7328 can accept true bipolar analog input signals,
±10 V, ±5 V, ±2.5 V, and 0 V to +10 V unipolar signals.
The eight analog inputs can be configured as eight singleended inputs, four true differential input pairs, four pseudo
differential inputs, or seven pseudo differential inputs.
1 MSPS serial interface. SPI®-/QSPI™-/DSP-/MICROWIRE™compatible interface.
Low power, 31 mW, at a maximum throughput rate of
1 MSPS.
Channel sequencer.
Table 1. Similar Product Selection
Device
Number
AD7329
AD7327
AD7324
AD7323
AD7322
AD7321
1
Throughput
Rate
1000 kSPS
500 kSPS
1000 kSPS
500 kSPS
1000 kSPS
500 kSPS
Number of Bits
12-bit plus sign
12-bit plus sign
12-bit plus sign
12-bit plus sign
12-bit plus sign
12-bit plus sign
Number of
Channels
8
8
4
4
2
2
Protected by U.S. Patent No. 6,731,232.
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2005–2014 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
AD7328* PRODUCT PAGE QUICK LINKS
Last Content Update: 02/23/2017
COMPARABLE PARTS
REFERENCE MATERIALS
View a parametric search of comparable parts.
Technical Articles
• MS-2210: Designing Power Supplies for High Speed ADC
EVALUATION KITS
• AD7328 Evaluation Board
DESIGN RESOURCES
• AD7328 Material Declaration
DOCUMENTATION
• PCN-PDN Information
Data Sheet
• Quality And Reliability
• AD7328: 8-Channel, Software-Selectable,True Bipolar
Input, 12-Bit Plus Sign ADC Data Sheet
• Symbols and Footprints
User Guides
DISCUSSIONS
• UG-419: Evaluating the AD7327/AD7328
View all AD7328 EngineerZone Discussions.
SOFTWARE AND SYSTEMS REQUIREMENTS
SAMPLE AND BUY
• AD7328 - Microcontroller No-OS Driver
Visit the product page to see pricing options.
• AD7328 Evaluation Software
• AD7328 FMC-SDP Interposer & Evaluation Board / Xilinx
KC705 Reference Design
TECHNICAL SUPPORT
• BeMicro FPGA Project for AD7328 with Nios driver
Submit a technical question or find your regional support
number.
REFERENCE DESIGNS
DOCUMENT FEEDBACK
• CN0047
Submit feedback for this data sheet.
This page is dynamically generated by Analog Devices, Inc., and inserted into this data sheet. A dynamic change to the content on this page will not
trigger a change to either the revision number or the content of the product data sheet. This dynamic page may be frequently modified.
AD7328
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Sequence Register ....................................................................... 24
General Description ......................................................................... 1
Range Registers ........................................................................... 24
Functional Block Diagram .............................................................. 1
Sequencer Operation ..................................................................... 25
Product Highlights ........................................................................... 1
Reference ..................................................................................... 27
Revision History ............................................................................... 2
VDRIVE ............................................................................................ 27
Specifications..................................................................................... 3
Temperature Indicator ............................................................... 27
Timing Specifications .................................................................. 6
Modes of Operation ....................................................................... 28
Absolute Maximum Ratings............................................................ 7
Normal Mode (PM1 = PM0 = 0) ............................................. 28
ESD Caution .................................................................................. 7
Full Shutdown Mode (PM1 = PM0 = 1) ................................. 28
Pin Configuration and Function Descriptions ............................. 8
Autoshutdown Mode (PM1 = 1, PM0 = 0) ............................. 29
Typical Performance Characteristics ............................................. 9
Autostandby Mode (PM1 = 0, PM0 = 1) ................................ 29
Terminology .................................................................................... 13
Power vs. Throughput Rate ....................................................... 30
Theory of Operation ...................................................................... 15
Serial Interface ................................................................................ 31
Circuit Information .................................................................... 15
Microprocessor Interfacing ........................................................... 32
Converter Operation .................................................................. 15
AD7328 to ADSP-21xx .............................................................. 32
Analog Input Structure .............................................................. 16
AD7328 to ADSP-BF53x ........................................................... 32
Typical Connection Diagram ................................................... 18
Applications Information .............................................................. 33
Analog Input ............................................................................... 18
Layout and Grounding .............................................................. 33
Driver Amplifier Choice ............................................................ 20
Power Supply Configuration .................................................... 33
Registers ........................................................................................... 21
Outline Dimensions ....................................................................... 34
Addressing Registers .................................................................. 21
Ordering Guide .......................................................................... 34
Control Register .......................................................................... 22
REVISION HISTORY
1/14—Rev. B to Rev. C
Changes to Circuit Information Section and Table 6 ................ 15
Changes to Addressing Registers Section.................................... 21
Changes to Power Supply Configuration Section ...................... 33
Changes to Ordering Guide .......................................................... 34
2/10—Rev. A to Rev. B
Change to Product Highlights Section .......................................... 1
Changes to DC Accuracy Parameter, Test Conditions/
Comments, Table 2 ....................................................................... 3
Changes to Normal Mode (Operational) ICC and IDRIVE
Parameter and to Power Dissipation Normal Mode
Parameter, Table 2 ........................................................................ 5
Changes to Table 14 and Table 15 ................................................ 32
Added Power Supply Configuration Section and Figure 56 ..... 33
Changes to Ordering Guide .......................................................... 34
6/06—Rev. 0 to Rev. A
Changes to Table 1.............................................................................1
Changes to Specifications .................................................................3
Added Thermal Hysteresis to Terminology Section.................. 14
Change to Figure 42 ....................................................................... 20
Change to Control Register Section............................................. 23
10/05—Revision 0: Initial Version
Rev. C | Page 2 of 36
Data Sheet
AD7328
SPECIFICATIONS
Unless otherwise noted, VDD = 12 V to 16.5 V, VSS = −12 V to −16.5 V, VCC = 4.75 V to 5.25 V, VDRIVE = 2.7 V to 5.25 V, VREF = 2.5 V to 3.0 V
internal/external, fSCLK = 20 MHz, fS = 1 MSPS, TA = TMAX to TMIN. With VCC < 4.75 V, all specifications are typical.
Table 2.
Parameter 1
DYNAMIC PERFORMANCE
Signal-to-Noise Ratio (SNR)
Signal-to-Noise and Distortion
(SINAD) 2
Min
B Version
Typ
Max
76
72.5
75
dB
dB
dB
76
dB
dB
72.5
dB
72
Total Harmonic Distortion (THD)2
−80
−82
−77
−80
Peak Harmonic or Spurious Noise
(SFDR)2
dB
dB
dB
dB
−80
dB
−78
dB
dB
−82
Intermodulation Distortion (IMD)2
Second-Order Terms
Third-Order Terms
Aperture Delay 3
Aperture Jitter3
Common-Mode Rejection Ratio
(CMRR)2
Channel-to-Channel Isolation2
Full Power Bandwidth
Unit
−79
dB
−88
−90
7
50
−79
dB
dB
ns
ps
dB
−72
22
5
dB
MHz
MHz
DC ACCURACY 4
Test Conditions/Comments
fIN = 50 kHz sine wave
Differential mode
Single-ended/pseudo differential mode
Differential mode; ±2.5 V and ±5 V ranges
Differential mode; 0 V to +10 V and ±10 V ranges
Single-ended/pseudo differential mode; ±2.5 V and ±5 V
ranges
Single-ended/pseudo differential mode; 0 V to +10 V
and ±10 V ranges
Differential mode; ±2.5 V and ±5 V ranges
Differential mode; 0 V to +10 V and ±10 V ranges
Single-ended/pseudo differential mode; ±2.5 V and ±5 V
ranges
Single-ended/pseudo differential mode; 0 V to +10 V
and ±10 V ranges
Differential mode; ±2.5 V and ±5 V ranges
Differential mode; 0 V to +10 V and ±10 V ranges
Single-ended/pseudo differential mode; ±2.5 V and ±5 V
ranges
Single-ended/pseudo differential mode; 0 V to +10 V
and ±10 V ranges
fa = 50 kHz, fb = 30 kHz
Up to 100 kHz ripple frequency; see Figure 17
fIN on unselected channels up to 100 kHz; see Figure 14
At 3 dB
At 0.1 dB
All specifications are typical for 0 V to 10 V mode
Single-ended/pseudo differential mode 1 LSB =
FSR/4096, unless otherwise noted
Differential mode 1 LSB = FSR/8192, unless otherwise
noted
Resolution
No Missing Codes
13
12-bit
plus sign
(13 bits)
11-bit
plus sign
(12 bits)
Integral Nonlinearity2
±1.1
±1
−0.7/+1.2
Bits
Bits
Differential mode
Bits
Single-ended/pseudo differential mode
LSB
LSB
LSB
Differential mode
Single-ended/pseudo differential mode
Single-ended/pseudo differential mode (LSB = FSR/8192)
Rev. C | Page 3 of 36
AD7328
Parameter 1
Differential Nonlinearity2
Data Sheet
Min
B Version
Typ
Max
−0.9/+1.5
Unit
LSB
±0.9
LSB
−4/+9
−7/+10
±0.6
±0.5
±8
±14
±0.5
±0.5
±4
±7
±0.5
±0.5
±8.5
±7.5
±0.5
±0.5
±4
±6
±0.5
±0.5
LSB
LSB
LSB
LSB
LSB
LSB
LSB
LSB
LSB
LSB
LSB
LSB
LSB
LSB
LSB
LSB
LSB
LSB
LSB
LSB
LSB
−0.7/+1
Offset Error2, 5
Offset Error Match2, 5
Gain Error2, 5
Gain Error Match2, 5
Positive Full-Scale Error2, 6
Positive Full-Scale Error Match2, 6
Bipolar Zero Code Error2, 6
Bipolar Zero Code Error Match2, 6
Negative Full-Scale Error2, 6
Negative Full-Scale Error Match2, 6
ANALOG INPUT
Input Voltage Ranges
(Programmed via Range Register)
±10
±5
±2.5
0 to 10
V
V
V
V
±3.5
±6
±5
+3/−5
V
V
V
V
nA
pF
pF
pF
pF
Pseudo Differential VIN(−)
Input Range
DC Leakage Current
Input Capacitance3
REFERENCE INPUT/OUTPUT
Input Voltage Range
Input DC Leakage Current
Input Capacitance
Reference Output Voltage
Long Term Stability
Output Voltage Hysteresis
Reference Output Voltage Error
at 25°C
Reference Output Voltage
TMIN to TMAX
Reference Temperature Coefficient
Reference Output Impedance
±200
13.5
16.5
21.5
3
2.5
3
±1
±5
V
µA
pF
V
ppm
ppm
mV
±10
mV
25
ppm/°C
ppm/°C
Ω
10
2.5
150
50
6
7
Rev. C | Page 4 of 36
Test Conditions/Comments
Differential mode; guaranteed no missing codes to
13 bits
Single-ended mode; guaranteed no missing codes to
12 bits
Single-ended/pseudo differential mode (LSB = FSR/8192)
Single-ended/pseudo differential mode
Differential mode
Single-ended/pseudo differential mode
Differential mode
Single-ended/pseudo differential mode
Differential mode
Single-ended/pseudo differential mode
Differential mode
Single-ended/pseudo differential mode
Differential mode
Single-ended/pseudo differential mode
Differential mode
Single-ended/pseudo differential mode
Differential mode
Single-ended/pseudo differential mode
Differential mode
Single-ended/pseudo differential mode
Differential mode
Single-ended/pseudo differential mode
Differential mode
Reference = 2.5 V; see Table 6
VDD = 10 V min, VSS = −10 V min, VCC = 2.7 V to 5.25 V
VDD = 5 V min, VSS = −5 V min, VCC = 2.7 V to 5.25 V
VDD = 5 V min, VSS = − 5 V min, VCC = 2.7 V to 5.25 V
VDD = 10 V min, VSS = AGND min, VCC = 2.7 V to 5.25 V
VDD = 16.5 V, VSS = −16.5 V, VCC = 5 V; see Figure 40 and
Figure 41
Reference = 2.5 V; range = ±10 V
Reference = 2.5 V; range = ±5 V
Reference = 2.5 V; range = ±2.5 V
Reference = 2.5 V; range = 0 V to +10 V
VIN = VDD or VSS
When in track, ±10 V range
When in track, ±5 V and 0 V to +10 V ranges
When in track, ±2.5 V range
When in hold, all ranges
For 1000 hours
Data Sheet
Parameter 1
LOGIC INPUTS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current, IIN
Input Capacitance, CIN3
LOGIC OUTPUTS
Output High Voltage, VOH
Output Low Voltage, VOL
Floating-State Leakage Current
Floating-State Output Capacitance3
Output Coding
AD7328
B Version
Typ
Min
Unit
Test Conditions/Comments
0.8
0.4
±1
V
V
V
µA
pF
VCC = 4.75 V to 5.25 V
VCC = 2.7 to 3.6 V
VIN = 0 V or VDRIVE
0.4
±1
V
V
µA
pF
2.4
10
VDRIVE − 0.2
5
Straight natural binary
Twos complement
CONVERSION RATE
Conversion Time
Track-and-Hold Acquisition Time2, 3
Throughput Rate
POWER REQUIREMENTS
VDD
VSS
VCC
VDRIVE
Normal Mode (Static)
Normal Mode (Operational)
IDD
ISS
ICC and IDRIVE
Autostandby Mode (Dynamic)
IDD
ISS
ICC and IDRIVE
Autoshutdown Mode (Static)
IDD
ISS
ICC and IDRIVE
Full Shutdown Mode
IDD
ISS
ICC and IDRIVE
POWER DISSIPATION
Normal Mode
Max
12
−12
2.7
2.7
ns
ns
MSPS
kSPS
16.5
−16.5
5.25
5.25
V
V
V
V
mA
16 SCLK cycles with SCLK = 20 MHz
Full-scale step input; see the Terminology section
VCC = 4.75 V to 5.25 V; see the Serial Interface section
VCC < 4.75 V
Digital inputs = 0 V or VDRIVE
See Table 6
See Table 6
See Table 6; typical specifications for VCC < 4.75 V
360
410
3.4
µA
µA
mA
200
210
1.3
µA
µA
mA
1
1
1
µA
µA
µA
1
1
1
µA
µA
µA
VDD/VSS = ±16.5 V, VCC/VDRIVE = 5.25 V
fS = 1 MSPS
VDD = 16.5 V
VSS = −16.5 V
VCC/VDRIVE = 5.25 V
fS = 250 kSPS
VDD = 16.5 V
VSS = −16.5 V
VCC/VDRIVE = 5.25 V
SCLK on or off
VDD = 16.5 V
VSS = −16.5 V
VCC/VDRIVE = 5.25 V
SCLK on or off
VDD = 16.5 V
VSS = −16.5 V
VCC/VDRIVE = 5.25 V
31
mW
mW
µW
VDD = 16.5 V, VSS = −16.5 V, VCC = 5.25 V
VDD = 12 V, VSS = −12 V, VCC = 5 V
VDD = 16.5 V, VSS = −16.5 V, VCC = 5.25 V
21
Full Shutdown Mode
Coding bit set to 1 in control register
Coding bit set to 0 in control register
800
305
1
770
0.9
ISOURCE = 200 µA
ISINK = 200 µA
38.25
Temperature range is −40°C to +85°C.
See the Terminology section.
Sample tested during initial release to ensure compliance.
4
For dc accuracy specifications, the LSB size for differential mode is FSR/8192. For single-ended mode/pseudo differential mode, the LSB size is FSR/4096, unless otherwise noted.
5
Unipolar 0 V to 10 V range with straight binary output coding.
6
Bipolar range with twos complement output coding.
1
2
3
Rev. C | Page 5 of 36
AD7328
Data Sheet
TIMING SPECIFICATIONS
VDD = 12 V to 16.5 V, VSS = −12 V to −16.5 V, VCC = 2.7 V to 5.25 V, VDRIVE = 2.7 V to 5.25 V, VREF = 2.5 V to 3.0 V internal/external,
TA = TMAX to TMIN. Timing specifications apply with a 32 pF load, unless otherwise noted. 1
Table 3.
Parameter
fSCLK
tCONVERT
tQUIET
t1
t2 2
t3
t4
t5
t6
t7
t8
t9
t10
tPOWER-UP
2
Unit
kHz min
MHz max
ns max
ns min
ns min
ns min
ns min
ns max
ns max
ns min
ns min
ns min
ns max
ns min
ns min
ns min
ns max
µs max
µs typ
Description
VDRIVE ≤ VCC
tSCLK = 1/fSCLK
Minimum time between end of serial read and next falling edge of CS
Minimum CS pulse width
CS to SCLK setup time; bipolar input ranges (±10 V, ±5 V, ±2.5 V)
Unipolar input range (0 V to 10 V)
Delay from CS until DOUT three-state disabled
Data access time after SCLK falling edge
SCLK low pulse width
SCLK high pulse width
SCLK to data valid hold time
SCLK falling edge to DOUT high impedance
SCLK falling edge to DOUT high impedance
DIN setup time prior to SCLK falling edge
DIN hold time after SCLK falling edge
Power up from autostandby
Power up from full shutdown/autoshutdown mode, internal reference
Power up from full shutdown/autoshutdown mode, external reference
Sample tested during initial release to ensure compliance. All input signals are specified with tr = tf = 5 ns (10% to 90% of VDRIVE) and timed from a voltage level of 1.6 V.
When using the 0 V to 10 V unipolar range, running at 1 MSPS throughput rate with t2 at 20 ns, the mark-space ratio must be limited to 50:50.
t1
CS
tCONVERT
t2
SCLK
t6
1
2
3
4
3 IDENTIFICATION BITS
t3
ADD1
DOUT
THREE- ADD2
t9
STATE
DIN
WRITE
REG
SEL1
ADD0
SIGN
5
t4
13
14
DB11
15
16
t5
t7
DB10
DB2
t8
DB1
t10
REG
SEL2
tQUIET
DB0
THREE-STATE
MSB
LSB
Figure 2. Serial Interface Timing Diagram
Rev. C | Page 6 of 36
DON’T
CARE
04852-002
1
Limit at TMIN, TMAX
VCC < 4.75 V
VCC = 4.75 V to 5.25 V
50
50
14
20
16 × tSCLK
16 × tSCLK
75
60
12
5
25
20
45
35
26
14
57
43
0.4 × tSCLK
0.4 × tSCLK
0.4 × tSCLK
0.4 × tSCLK
13
8
40
22
10
9
4
4
2
2
750
750
500
500
25
25
Data Sheet
AD7328
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted
Table 4.
Parameter
VDD to AGND, DGND
VSS to AGND, DGND
VDD to VCC
VCC to AGND, DGND
VDRIVE to AGND, DGND
AGND to DGND
Analog Input Voltage to AGND1
Digital Input Voltage to DGND
Digital Output Voltage to GND
REFIN to AGND
Input Current to Any Pin
Except Supplies2
Operating Temperature Range
Storage Temperature Range
Junction Temperature
TSSOP Package
θJA Thermal Impedance
θJC Thermal Impedance
Pb-Free Temperature, Soldering
Reflow
ESD
Rating
−0.3 V to +16.5 V
+0.3 V to −16.5 V
VCC − 0.3 V to +16.5 V
−0.3 V to +7 V
−0.3 V to +7 V
−0.3 V to +0.3 V
VSS − 0.3 V to VDD + 0.3 V
−0.3 V to +7 V
−0.3 V to VDRIVE + 0.3 V
−0.3 V to VCC + 0.3 V
±10 mA
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
ESD CAUTION
−40°C to +85°C
−65°C to +150°C
150°C
143°C/W
45°C/W
260(0)°C
2.5 kV
If the analog inputs are driven from alternative VDD and VSS supply circuitry,
Schottky diodes should be placed in series with the VDD and VSS supplies of
the AD7328 (see the Power Supply Configuration section).
2
Transient currents of up to 100 mA do not cause SCR latch-up.
1
Rev. C | Page 7 of 36
AD7328
Data Sheet
CS 1
20
SCLK
DIN 2
19
DGND
DGND 3
18
DOUT
17
VDRIVE
AGND 4
REFIN/OUT 5
AD7328
TOP VIEW
(Not to Scale)
16
VCC
VSS 6
15
VDD
VIN0 7
14
VIN2
8
13
VIN3
VIN4 9
12
VIN6
VIN5 10
11
VIN7
VIN1
04852-003
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
Figure 3. TSSOP Pin Configuration
Table 5. Pin Function Descriptions
Pin No.
1
Mnemonic
CS
2
DIN
3, 19
DGND
4
AGND
5
REFIN/OUT
6
7, 8, 14, 13, 9, 10,
12, 11
VSS
VIN0 to VIN7
15
16
VDD
VCC
17
VDRIVE
18
DOUT
20
SCLK
Description
Chip Select. Active low logic input. This input provides the dual function of initiating conversions on
the AD7328 and frames the serial data transfer.
Data In. Data to be written to the on-chip registers is provided on this input and is clocked into the
register on the falling edge of SCLK (see the Registers section).
Digital Ground. Ground reference point for all digital circuitry on the AD7328. The DGND and AGND
voltages should ideally be at the same potential and must not be more than 0.3 V apart, even on a
transient basis.
Analog Ground. Ground reference point for all analog circuitry on the AD7328. All analog input signals
and any external reference signal should be referred to this AGND voltage. The AGND and DGND voltages
should ideally be at the same potential and must not be more than 0.3 V apart, even on a transient basis.
Reference Input/Reference Output. The on-chip reference is available on this pin for use external to the
AD7328. The nominal internal reference voltage is 2.5 V, which appears at the pin. A 680 nF capacitor
should be placed on the reference pin. Alternatively, the internal reference can be disabled and an
external reference can be applied to this input. On power-up, the external reference mode is the default
condition (see the Reference section).
Negative Power Supply Voltage. This is the negative supply voltage for the analog input section.
Analog Input 0 to Analog Input 7. The analog inputs are multiplexed into the on-chip track-and-hold.
The analog input channel for conversion is selected by programming the channel address bits, ADD2
through ADD0, in the control register. The inputs can be configured as eight single-ended inputs, four
true differential input pairs, four pseudo differential inputs, or seven pseudo differential inputs. The
configuration of the analog inputs is selected by programming the mode bits, Bit Mode 1 and Bit Mode 0,
in the control register. The input range on each input channel is controlled by programming the range
registers. Input ranges of ±10 V, ±5 V, ±2.5 V, and 0 V to +10 V can be selected on each analog input
channel when a +2.5 V reference voltage is used (see the Reference section).
Positive Power Supply Voltage. This is the positive supply voltage for the analog input section.
Analog Supply Voltage, 2.7 V to 5.25 V. This is the supply voltage for the ADC core on the AD7328.
This supply should be decoupled to AGND. Specifications apply from VCC = 4.75 V to 5.25 V.
Logic Power Supply Input. The voltage supplied at this pin determines at what voltage the interface
operates. This pin should be decoupled to DGND. The voltage at this pin may be different to that at VCC,
but it should not exceed VCC by more than 0.3 V.
Serial Data Output. The conversion output data is supplied to this pin as a serial data stream. The bits
are clocked out on the falling edge of the SCLK input, and 16 SCLKs are required to access the data. The
data stream consists of three channel identification bits, the sign bit, and 12 bits of conversion data.
The data is provided MSB first (see the Serial Interface section).
Serial Clock, Logic Input. A serial clock input provides the SCLK used for accessing the data from the
AD7328. This clock is also used as the clock source for the conversion process.
Rev. C | Page 8 of 36
Data Sheet
AD7328
TYPICAL PERFORMANCE CHARACTERISTICS
0
1.0
4096 POINT FFT
VCC = VDRIVE = 5V
VDD, VSS = ±15V
TA = 25°C
INT/EXT 2.5V REFERENCE
±10V RANGE
FIN = 50kHz
SNR = 77.30dB
SINAD = 76.85dB
THD = –86.96dB
SFDR = –88.22dB
SNR (dB)
–40
–60
–80
VCC = VDRIVE = 5V
0.8 TA = 25°C
VDD, VSS = ±15V
0.6
INT/EXT 2.5V REFERENCE
±10V RANGE
+INL = +0.55LSB
–INL = –0.68LSB
0.4
INL ERROR (LSB)
–20
0.2
0
–0.2
–0.4
–100
04852-004
–140
0
50
100
150
200
250
300
350
400
450
04852-007
–0.6
–120
–0.8
–1.0
500
0
FREQUENCY (kHz)
Figure 7. Typical INL for True Differential Mode
Figure 4. FFT for True Differential Mode
1.0
0
4096 POINT FFT
VCC = VDRIVE = 5V
VDD, VSS = ±15V
TA = 25°C
INT/EXT 2.5V REFERENCE
±10V RANGE
FIN = 50kHz
SNR = 74.67dB
SINAD = 74.03dB
THD = –82.68dB
SFDR = –85.40dB
–60
–80
0.6
0.4
0.2
0
–0.2
–0.4
–100
VCC = VDRIVE = 5V
±10V RANGE
TA = 25°C
+DNL = +0.79LSB
VDD, VSS = ±15V
–DNL = –0.38LSB
INT/EXT 2.5V REFERENCE
–0.6
04852-005
–120
–140
0
50
100
150
200
250
300
350
400
450
–0.8
–1.0
500
FREQUENCY (kHz)
0.8
0.8
0.6
0.6
0.4
0.4
INL ERROR (LSB)
1.0
0.2
0
–0.2
0
0
–0.2
VCC = VDRIVE = 5V
TA = 25°C
VDD, VSS = ±15V
–0.6
INT/EXT 2.5V REFERENCE
±10V RANGE
–0.8
+INL = +0.87LSB
–INL = –0.49LSB
–1.0
0
1024
2048
3072
4096
5120
6144
7168
8192
512
1536
2560
3584
4608
5632
6656
7680
CODE
04852-044
–0.6
–0.8
0.2
–0.4
04852-006
DNL ERROR (LSB)
1.0
VCC = VDRIVE = 5V
TA = 25°C
VDD, VSS = ±15V
INT/EXT 2.5V REFERENCE
±10V RANGE
+DNL = +0.72LSB
–DNL = –0.22LSB
1024
2048
3072
4096
5120
6144
7168
8192
512
1536
2560
3584
4608
5632
6656
7680
CODE
Figure 8. Typical DNL for Single-Ended Mode
Figure 5. FFT for Single-Ended Mode
–0.4
0
04852-043
SNR (dB)
–40
0.8
DNL ERROR (LSB)
–20
–1.0
1024
2048
3072
4096
5120
6144
7168
8192
512
1536
2560
3584
4608
5632
6656
7680
CODE
1024
2048
3072
4096
5120
6144
7168
8192
512
1536
2560
3584
4608
5632
6656
7680
CODE
Figure 9. Typical INL for Single-Ended Mode
Figure 6. Typical DNL for True Differential Mode
Rev. C | Page 9 of 36
AD7328
Data Sheet
–50
–60
THD (dB)
–65
±10V DIFF ±5V DIFF
75
0V TO +10V DIFF
0V TO +10V SE
70
±5V SE
–70
–75
±2.5V DIFF
±10V SE
±10V DIFF
SINAD (dB)
–55
80
VCC = 5V
VDD/VSS = ±12V
TA = 25°C
fS = 1MSPS
±5V DIFF
±2.5V DIFF
–80
0V TO +10V SE
±2.5V SE
65
±10V SE
±5V SE
0V TO +10V DIFF
60
–85
±2.5V SE
VCC = 3V
VDD/VSS = ±12V
TA = 25°C
fS = 1MSPS
04852-008
55
–95
–100
10
100
50
10
1000
100
ANALOG INPUT FREQUENCY (kHz)
Figure 13. SINAD vs. Analog Input Frequency for Single-Ended (SE) and
Differential Mode (Diff) at 3 V VCC
–50
CHANNEL-TO-CHANNEL ISOLATION (dB)
VCC = 3V
VDD/VSS = ±12V
TA = 25°C
fS = 1MSPS
±10V SE
–65
0V TO +10V SE
–70
±5V SE
–75
–80
±10V DIFF
±2.5V SE
–85
04852-009
±5V DIFF
–90
–95
±2.5V DIFF
–100
10
100
VCC = 3V
–60
VCC = 5V
–65
–70
–75
–80
VDD/VSS = ±12V
SINGLE-ENDED MODE
fS = 1MSPS
TA = 25°C
50kHz ON SELECTED CHANNEL
–85
–90
–95
0
1000
100
Figure 11. THD vs. Analog Input Frequency for Single-Ended (SE) and True
Differential Mode (Diff) at 3 V VCC
10k
±10V DIFF
±5V DIFF
75
NUMBER OF OCCURRENCES
SINAD (dB)
70
±2.5V SE
0V TO +10V SE
±5V SE
±10V SE
0V TO +10V DIFF
VCC = 5V
VDD/VSS = ±12V
TA = 25°C
fS = 1MSPS
100
04852-010
60
55
9469
9k
±2.5V DIFF
65
300
400
500
600
Figure 14. Channel-to-Channel Isolation
80
50
10
200
FREQUENCY OF INPUT NOISE (kHz)
ANALOG INPUT FREQUENCY (kHz)
8k
VCC = 5V
VDD/VSS = ±12V
RANGE = ±10V
10k SAMPLES
TA = 25°C
7k
6k
5k
4k
3k
2k
1k
0
228
303
0
0
–2
1000
ANALOG INPUT FREQUENCY (kHz)
–1
0
1
2
CODE
Figure 12. SINAD vs. Analog Input Frequency for Single-Ended (SE) and
Differential Mode (Diff) at 5 V VCC
Rev. C | Page 10 of 36
Figure 15. Histogram of Codes, True Differential Mode
04852-013
THD (dB)
0V TO +10V DIFF
–55
04852-012
–50
–60
1000
ANALOG INPUT FREQUENCY (kHz)
Figure 10. THD vs. Analog Input Frequency for Single-Ended (SE) and True
Differential Mode (Diff) at 5 V VCC
–55
04852-011
–90
Data Sheet
AD7328
8k
2.0
7600
VCC = 5V
VDD/VSS = ±12V
RANGE = ±10V
10k SAMPLES
TA = 25°C
6k
1.5
INL = 500kSPS
5k
4k
3k
0.5
INL = 1MSPS
0
INL = 500kSPS
1165
0
23
–3
–2
–1
0
1
11
0
2
3
–2.0
5
7
–50
–55
–55
–60
–60
–65
–65
PSRR (dB)
VCC = 5V
–75
VCC = 3V
–95
0
200
400
600
800
1000
VCC = 3V
–70
–75
VDD = 12V
–80
VSS = –12V
–95
–100
1200
0
–50
–55
DNL = 500kSPS
–60
–65
0.5
THD (dB)
DNL = 1MSPS
DNL = 1MSPS
–0.5
DNL = 500kSPS
±5V RANGE
VCC = VDRIVE = 5V
INTERNAL REFERENCE
SINGLE-ENDED MODE
5
7
9
04852-049
DNL ERROR (LSB)
1.0
DNL = 750kSPS
11
13
400
600
800
1000
1200
Figure 20. PSRR vs. Supply Ripple Frequency Without Supply Decoupling
DNL = 750kSPS
1.5
200
SUPPLY RIPPLE FREQUENCY (kHz)
2.0
–1.5
19
–90
Figure 17. CMRR vs. Common-Mode Ripple Frequency
–1.0
17
VCC = 5V
RIPPLE FREQUENCY (kHz)
0
15
100mV p-p SINE WAVE ON EACH SUPPLY
NO DECOUPLING
SINGLE-ENDED MODE
fS = 1MSPS
–85
DIFFERENTIAL MODE
FIN = 50kHz
VDD/VSS = ±12V
fS = 1MSPS
TA = 25°C
–90
13
04852-054
–85
04852-055
CMRR (dB)
–50
–80
11
Figure 19. INL Error vs. Supply Voltage at 500 kSPS, 750 kSPS, and 1 MSPS
Figure 16. Histogram of Codes, Single-Ended Mode
–70
9
±VDD/VSS SUPPLY VOLTAGE (V)
CODE
15
17
19
RIN = 100Ω, ±10V RANGE
RIN = 2000Ω, ±10V RANGE
RIN = 50Ω,
±10V RANGE
–70 RIN = 1000Ω, ±10V RANGE
RIN = 4700Ω,
±2.5V RANGE
–75
RIN = 2000Ω,
±2.5V RANGE
–80
RIN = 1000Ω,
±2.5V RANGE
–85
RIN = 100Ω,
±2.5V RANGE
–90
RIN = 50Ω,
±2.5V RANGE
–95
10
±VDD/VSS SUPPLY VOLTAGE (V)
VCC = VDRIVE = 5V
VDD/VSS = ±12V
TA = 25°C
INTERNAL REFERENCE
RANGE = ±10V AND ±2.5V
100
04852-015
0
±5V RANGE
VCC = VDRIVE = 5V
INTERNAL REFERENCE
SINGLE-ENDED MODE
INL = 1MSPS
–1.5
04852-014
1k
04852-050
1201
–2.0
INL = 750kSPS
–0.5
–1.0
2k
–100
INL = 750kSPS
1.0
INL ERROR (LSB)
NUMBER OF OCCURRENCES
7k
1000
ANALOG INPUT FREQUENCY (kHz)
Figure 18. DNL Error vs. Supply Voltage at 500 kSPS, 750 kSPS, and 1 MSPS
Figure 21. THD vs. Analog Input Frequency for Various Source Impedances,
True Differential Mode
Rev. C | Page 11 of 36
AD7328
–55
–60
THD (dB)
–65
VCC = VDRIVE = 5V
VDD/VSS = ±12V
TA = 25°C
INTERNAL REFERENCE
RANGE = ±10V AND ±2.5V
RIN = 2000Ω, ±10V RANGE
RIN = 100Ω,
±10V RANGE
–70 RIN = 1000Ω, ±10V RANGE
RIN = 50Ω,
±10V RANGE
–75
RIN = 2000Ω,
±2.5V RANGE
–80
RIN = 1000Ω,
±2.5V RANGE
–85
RIN = 100Ω,
±2.5V RANGE
–90
RIN = 50Ω,
±2.5V RANGE
–95
10
100
04852-016
–50
Data Sheet
1000
INPUT FREQUENCY (kHz)
Figure 22. THD vs. Analog Input Frequency for Various Source Impedances,
Single-Ended Mode
Rev. C | Page 12 of 36
Data Sheet
AD7328
TERMINOLOGY
Differential Nonlinearity
This is the difference between the measured and the ideal 1 LSB
change between any two adjacent codes in the ADC.
Integral Nonlinearity
This is the maximum deviation from a straight line passing
through the endpoints of the ADC transfer function. The
endpoints of the transfer function are zero scale (a point 1 LSB
below the first code transition) and full scale (a point 1 LSB above
the last code transition).
Offset Error
This applies to straight binary output coding. It is the deviation
of the first code transition (00 ... 000) to (00 ... 001) from the
ideal, that is, AGND + 1 LSB.
Offset Error Match
This is the difference in offset error between any two input
channels.
Gain Error
This applies to straight binary output coding. It is the deviation
of the last code transition (111 ... 110) to (111 ... 111) from the
ideal (that is, 4 × VREF − 1 LSB, 2 × VREF − 1 LSB, VREF − 1 LSB)
after adjusting for the offset error.
Gain Error Match
This is the difference in gain error between any two input channels.
Bipolar Zero Code Error
This applies when using twos complement output coding and a
bipolar analog input. It is the deviation of the midscale transition
(all 1s to all 0s) from the ideal input voltage, that is, AGND − 1 LSB.
Bipolar Zero Code Error Match
This refers to the difference in bipolar zero code error between
any two input channels.
Positive Full-Scale Error
This applies when using twos complement output coding and
any of the bipolar analog input ranges. It is the deviation of the
last code transition (011 … 110) to (011 … 111) from the ideal
(that is, 4 × VREF − 1 LSB, 2 × VREF − 1 LSB, VREF − 1 LSB) after
adjusting for the bipolar zero code error.
Positive Full-Scale Error Match
This is the difference in positive full-scale error between any
two input channels.
Negative Full-Scale Error
This applies when using twos complement output coding and
any of the bipolar analog input ranges. This is the deviation of
the first code transition (10 … 000) to (10 … 001) from the ideal
(that is, −4 × VREF + 1 LSB, −2 × VREF + 1 LSB, −VREF + 1 LSB)
after adjusting for the bipolar zero code error.
Negative Full-Scale Error Match
This is the difference in negative full-scale error between any
two input channels.
Track-and-Hold Acquisition Time
The track-and-hold amplifier returns to track mode after the
14th SCLK rising edge. Track-and-hold acquisition time is the
time required for the output of the track-and-hold amplifier to
reach its final value, within ±½ LSB, after the end of a conversion.
For the ±2.5 V range, the specified acquisition time is the time
required for the track-and-hold amplifier to settle to within ±1 LSB.
Signal-to-Noise-and-Distortion Ratio
This is the measured ratio of signal to (noise + distortion) at
the output of the ADC. The signal is the rms amplitude of the
fundamental. Noise is the sum of all nonfundamental signals up
to half the sampling frequency (fS/2), excluding dc. The ratio is
dependent on the number of quantization levels in the digitization
process. The more levels, the smaller the quantization noise.
Theoretically, the signal-to-noise-and-distortion ratio for an
ideal N-bit converter with a sine wave input is given by
Signal to (Noise + Distortion) = (6.02 N + 1.76) dB
For a 13-bit converter, this is 80.02 dB.
Total Harmonic Distortion
Total harmonic distortion (THD) is the ratio of the rms sum of
harmonics to the fundamental. For the AD7328, it is defined as
THD (dB) = 20 log
V 2 2 + V 3 2 + V 4 2 + V 5 2 + V6 2
V1
where V1 is the rms amplitude of the fundamental, and V2, V3,
V4, V5, and V6 are the rms amplitudes of the second through the
sixth harmonics.
Peak Harmonic or Spurious Noise
Peak harmonic or spurious noise is defined as the ratio of the
rms value of the next largest component in the ADC output
spectrum (up to fS/2, excluding dc) to the rms value of the
fundamental. Normally, the value of this specification is
determined by the largest harmonic in the spectrum, but for
ADCs where the harmonics are buried in the noise floor, the
largest harmonic could be a noise peak.
Rev. C | Page 13 of 36
AD7328
Data Sheet
Channel-to-Channel Isolation
Channel-to-channel isolation is a measure of the level of crosstalk
between any two channels. It is measured by applying a full-scale,
100 kHz sine wave signal to all unselected input channels and
determining the degree to which the signal attenuates in the
selected channel with a 50 kHz signal. Figure 14 shows the worst
case across all eight channels for the AD7328. The analog input
range is programmed to be the same on all channels.
Thermal Hysteresis
Thermal hysteresis is defined as the absolute maximum change
of reference output voltage after the device is cycled through
temperature from either
Intermodulation Distortion
With inputs consisting of sine waves at two frequencies, fa and fb,
any active device with nonlinearities creates distortion products
at sum and difference frequencies of mfa ± nfb, where m, n = 0,
1, 2, 3, and so on. Intermodulation distortion terms are those
for which neither m nor n are equal to 0. For example, the
second-order terms include (fa + fb) and (fa − fb), whereas the
third-order terms include (2fa + fb), (2fa − fb), (fa + 2fb), and
(fa − 2fb).
It is expressed in ppm using the following equation:
The AD7328 is tested using the CCIF standard where two input
frequencies near the top end of the input bandwidth are used.
In this case, the second-order terms are usually distanced in
frequency from the original sine waves, whereas the third-order
terms are usually at a frequency close to the input frequencies.
As a result, the second- and third-order terms are specified
separately. The calculation of the intermodulation distortion is
per the THD specification, where it is the ratio of the rms sum
of the individual distortion products to the rms amplitude of
the sum of the fundamentals expressed in decibels.
T_HYS+ = +25°C to TMAX to +25°C
or
T_HYS− = +25°C to TMIN to +25°C
V HYS (ppm) =
V REF (25°C) − V REF (T _ HYS)
× 10 6
V REF (25°C)
where:
VREF(25°C) is VREF at 25°C.
VREF(T_HYS) is the maximum change of VREF at T_HYS+ or
T_HYS−.
Common-Mode Rejection Ratio (CMRR)
CMRR is defined as the ratio of the power in the ADC output
at full-scale frequency, f, to the power of a 100 mV sine wave
applied to the common-mode voltage of the VIN+ and VIN−
frequency, fS, as
CMRR (dB) = 10 log (Pf/PfS)
where Pf is the power at frequency f in the ADC output, and PfS
is the power at frequency fS in the ADC output (see Figure 17).
Power Supply Rejection (PSR)
Variations in power supply affect the full-scale transition but not
the linearity of the converter. Power supply rejection is the
maximum change in the full-scale transition point due to a
change in power supply voltage from the nominal value (see the
Typical Performance Characteristics section).
Rev. C | Page 14 of 36
Data Sheet
AD7328
THEORY OF OPERATION
The AD7328 is a fast, 8-channel, 12-bit plus sign, bipolar input,
serial ADC. The AD7328 can accept bipolar input ranges that
include ±10 V, ±5 V, and ±2.5 V; it can also accept a 0 V to +10 V
unipolar input range. A different analog input range can be
programmed on each analog input channel via the on-chip
registers. The AD7328 has a high speed serial interface that
can operate at throughput rates up to 1 MSPS.
The AD7328 requires VDD and VSS dual supplies for the high
voltage analog input structures. These supplies must be equal
to or greater than the analog input range. See Table 6 for the
requirements of these supplies for each analog input range. The
AD7328 requires a low voltage 2.7 V to 5.25 V VCC supply to
power the ADC core.
Table 6. Reference and Supply Requirements for Each
Analog Input Range
Selected Analog
Input Range (V)
±10
±5
±2.5
0 to +10
1
Reference
Voltage (V)
2.5
3.0
2.5
3.0
2.5
3.0
2.5
3.0
Full-Scale
Input
Range (V)
±10
±12
±5
±6
±2.5
±3
0 to +10
0 to +12
VCC (V)
3/5
3/5
3/5
3/5
3/5
3/5
3/5
3/5
Minimum
VDD/VSS
(V)1
±10
±12
±5
±6
±5
±5
+10/AGND
+12/AGND
Guaranteed performance for VDD = 12 V to 16.5 V and VSS = −12 V to −16.5 V.
The performance specifications are guaranteed for VDD = 12 V
to 16.5 V and VSS = −12 V to −16.5 V. With VDD and VSS supplies
outside this range, the AD7328 is fully functional but performance
is not guaranteed. When the AD7328 is configured with the
minimum VDD and VSS supplies for a chosen analog input range,
the throughput rate should be decreased from the maximum
throughput range (see the Typical Performance Characteristics
section). Figure 18 and Figure 19 show the change in INL and
DNL as the VDD and VSS voltages are varied. When operating at
the maximum throughput rate, as the VDD and VSS supply voltages
are reduced, the INL and DNL error increases. However, as the
throughput rate is reduced with the minimum VDD and VSS
supplies, the INL and DNL error is reduced.
Figure 31 shows the change in THD as the VDD and VSS supplies
are reduced. At the maximum throughput rate, the THD degrades
significantly as VDD and VSS are reduced. It is therefore necessary to
reduce the throughput rate when using minimum VDD and VSS
supplies so that there is less degradation of THD and the specified
performance can be maintained. The degradation is due to an
increase in the on resistance of the input multiplexer when the
VDD and VSS supplies are reduced.
The analog inputs can be configured as eight single-ended inputs,
four true differential input pairs, four pseudo differential inputs,
or seven pseudo differential inputs. Selection can be made by
programming the mode bits, Mode 0 and Mode 1, in the control
register.
The serial clock input accesses data from the part and provides the
clock source for the successive approximation ADC. The AD7328
has an on-chip 2.5 V reference. However, the AD7328 can also
work with an external reference. On power-up, the external
reference operation is the default option. If the internal reference
is preferable, the user must write to the reference bit in the
control register to select the internal reference operation.
The AD7328 also features power-down options to allow power
savings between conversions. The power-down modes are selected
by programming the on-chip control register as described in the
Modes of Operation section.
CONVERTER OPERATION
The AD7328 is a successive approximation analog-to-digital
converter built around two capacitive DACs. Figure 23 and
Figure 24 show simplified schematics of the ADC in singleended mode during the acquisition and conversion phases,
respectively. Figure 25 and Figure 26 show simplified schematics
of the ADC in differential mode during acquisition and conversion
phases, respectively.
The ADC is composed of control logic, a SAR, and capacitive
DACs. In Figure 23 (the acquisition phase), SW2 is closed and
SW1 is in Position A, the comparator is held in a balanced condition, and the sampling capacitor array acquires the signal on
the input.
CAPACITIVE
DAC
B
VIN0
A SW1
AGND
COMPARATOR
CS
SW2
CONTROL
LOGIC
04852-017
CIRCUIT INFORMATION
Figure 23. ADC Configuration During Acquisition Phase, Single-Ended Mode
When the ADC starts a conversion (see Figure 24), SW2 opens and
SW1 moves to Position B, causing the comparator to become
unbalanced. The control logic and the charge redistribution
DAC are used to add and subtract fixed amounts of charge from
the capacitive DAC to bring the comparator back into a balanced
condition. When the comparator is rebalanced, the conversion
is complete. The control logic generates the ADC output code.
Rev. C | Page 15 of 36
AD7328
Data Sheet
The ideal transfer characteristic for the AD7328 when twos
complement coding is selected is shown in Figure 27. The ideal
transfer characteristic for the AD7328 when straight binary
coding is selected is shown in Figure 28.
A SW1
CONTROL
LOGIC
SW2
AGND
04852-018
COMPARATOR
CS
B
VIN0
011...111
011...110
Figure 24. ADC Configuration During Conversion Phase, Single-Ended Mode
CAPACITIVE
DAC
A SW1
A SW2
B
–FSR/2 + 1LSB
AGND + 1LSB
AGND – 1LSB
+FSR/2 – 1LSB BIPOLAR RANGES
+FSR – 1LSB
UNIPOLAR RANGE
ANALOG INPUT
Figure 27. Twos Complement Transfer Characteristic, Bipolar Ranges
111...111
111...110
CONTROL
LOGIC
SW3
CS
VREF
CAPACITIVE
DAC
ADC CODE
VIN–
100...010
100...001
100...000
04852-019
VIN+
000...001
000...000
111...111
COMPARATOR
CS
B
ADC CODE
Figure 25 shows the differential configuration during the acquisition phase. For the conversion phase, SW3 opens and SW1
and SW2 move to Position B (see Figure 26). The output
impedances of the source driving the VIN+ and VIN− pins must
match; otherwise, the two inputs have different settling times,
resulting in errors.
04852-021
CAPACITIVE
DAC
111...000
011...111
Figure 25. ADC Configuration During Acquisition Phase, Differential Mode
A SW1
A SW2
B
SW3
Figure 28. Straight Binary Transfer Characteristic, Bipolar Ranges
CONTROL
LOGIC
ANALOG INPUT STRUCTURE
CS
VREF
CAPACITIVE
DAC
Figure 26. ADC Configuration During Conversion Phase, Differential Mode
Output Coding
The AD7328 default output coding is set to twos complement.
The output coding is controlled by the coding bit in the control
register. To change the output coding to straight binary coding,
the coding bit in the control register must be set. When operating
in sequence mode, the output coding for each channel in the
sequence is the value written to the coding bit during the last
write to the control register.
The analog inputs of the AD7328 can be configured as singleended, true differential, or pseudo differential via the control
register mode bits (see Table 10). The AD7328 can accept true
bipolar input signals. On power-up, the analog inputs operate as
eight single-ended analog input channels. If true differential or
pseudo differential is required, a write to the control register is
necessary after power-up to change this configuration.
Figure 29 shows the equivalent analog input circuit of the
AD7328 in single-ended mode. Figure 30 shows the equivalent
analog input structure in differential mode. The two diodes
provide ESD protection for the analog inputs.
VDD
Transfer Functions
D
The designed code transitions occur at successive integer
LSB values (that is, 1 LSB, 2 LSB, and so on). The LSB size
is dependent on the analog input range selected.
VIN0
C1
D
VSS
Table 7. LSB Sizes for Each Analog Input Range
Input Range
±10 V
±5 V
±2.5 V
0 V to +10 V
Full-Scale Range/8192 Codes
20 V
10 V
5V
10 V
R1
C2
04852-023
VIN–
04852-020
VIN+
–FSR/2 + 1LSB
+FSR/2 – 1LSB BIPOLAR RANGES
AGND + 1LSB
+FSR – 1LSB
UNIPOLAR RANGE
ANALOG INPUT
COMPARATOR
CS
B
04852-022
000...010
000...001
000...000
CAPACITIVE
DAC
Figure 29. Equivalent Analog Input Circuit, Single-Ended Mode
LSB Size
2.441 mV
1.22 mV
0.61 mV
1.22 mV
Rev. C | Page 16 of 36
Data Sheet
AD7328
VDD
C1
R1
C2
D
1.5 SCLK + t8 + tQUIET
VSS
to acquire the analog input signal. The ADC goes back into
hold mode on the CS falling edge.
VDD
C1
D
VSS
R1
C2
04852-024
D
VIN–
Figure 30. Equivalent Analog Input Circuit, Differential Mode
Care should be taken to ensure that the analog input does
not exceed the VDD and VSS supply rails by more than 300 mV.
Exceeding this value causes the diodes to become forward
biased and to start conducting into either the VDD supply rail
or the VSS supply rail. These diodes can conduct up to 10 mA
without causing irreversible damage to the part.
As the VDD/VSS supply voltage is reduced, the on resistance of
the input multiplexer increases. Therefore, based on the equation
for tACQ, it is necessary to increase the acquisition time provided
to the AD7328 and, hence, decrease the overall throughput rate.
Figure 31 shows that if the throughput rate is reduced when
operating with minimum VDD and VSS supplies, the specified
THD performance is maintained.
–50
VCC = VDRIVE = 5V
INTERNAL REFERENCE
TA = 25°C
FIN = 10kHz
±5V RANGE
SE MODE
–55
–60
–65
THD (dB)
In Figure 29 and Figure 30, Capacitor C1 is typically 4 pF and
can primarily be attributed to pin capacitance. Resistor R1 is a
lumped component made up of the on resistance of the input
multiplexer and the track-and-hold switch. Capacitor C2 is the
sampling capacitor; its capacitance varies depending on the
analog input range selected (see the Specifications section).
–70
–75
1MSPS
–80
750kSPS
–85
04852-051
D
VIN+
The AD7328 enters track mode on the 14th SCLK rising edge.
When the AD7328 is run at a throughput rate of 1 MSPS with a
20 MHz SCLK signal, the ADC has approximately
–90
500kSPS
Track-and-Hold Section
–95
The track-and-hold on the analog input of the AD7328 allows
the ADC to accurately convert an input sine wave of full-scale
amplitude to 13-bit accuracy. The input bandwidth of the trackand-hold is greater than the Nyquist rate of the ADC. The AD7328
can handle frequencies up to 22 MHz.
The track-and-hold enters its tracking mode on the 14th SCLK
rising edge after the CS falling edge. The time required to acquire
an input signal depends on how quickly the sampling capacitor
is charged. With zero source impedance, 305 ns is sufficient to
acquire the signal to the 13-bit level. The acquisition time for
the ±10 V, ±5 V, and 0 V to +10 V ranges to settle to within
±½ LSB is typically 200 ns.
The acquisition time required is calculated using the following
formula:
tACQ = 10 × ((RSOURCE + R) C)
where C is the sampling capacitance, and R is the resistance
seen by the track-and-hold amplifier looking at the input.
5
7
9
11
13
15
17
19
±VDD/VSS SUPPLIES (V)
Figure 31. THD vs. ±VDD/VSS Supply Voltage at 500 kSPS, 750 kSPS, and 1 MSPS
Unlike other bipolar ADCs, the AD7328 does not have a
resistive analog input structure. On the AD7328, the bipolar
analog signal is sampled directly onto the sampling capacitor.
This gives the AD7328 high analog input impedance. The
analog input impedance can be calculated from the following
formula:
Z = 1/(fS × CS)
where fS is the sampling frequency, and CS is the sampling
capacitor value.
CS depends on the analog input range chosen (see the
Specifications section). When operating at 1 MSPS, the analog
input impedance is typically 75 kΩ for the ±10 V range. As the
sampling frequency is reduced, the analog input impedance
further increases. As the analog input impedance increases, the
current required to drive the analog input therefore decreases.
For the AD7328, the value of R includes the on resistance of the
input multiplexer and is typically 300 Ω. RSOURCE should include
any extra source impedance on the analog input.
Rev. C | Page 17 of 36
AD7328
Data Sheet
V+
TYPICAL CONNECTION DIAGRAM
Figure 32 shows a typical connection diagram for the AD7328.
In this configuration, the AGND pin is connected to the analog
ground plane of the system, and the DGND pin is connected to
the digital ground plane of the system. The analog inputs on the
AD7328 can be configured to operate in single-ended, true differential, or pseudo differential mode. The AD7328 can operate
with either an internal or external reference. In Figure 32, the
AD7328 is configured to operate with the internal 2.5 V reference.
A 680 nF decoupling capacitor is required when operating with
the internal reference.
The VCC pin can be connected to either a 3 V or 5 V supply voltage.
VDD and VSS are the dual supplies for the high voltage analog
input structures. The voltage on these pins must be equal to or
greater than the highest analog input range selected on the analog
input channels (see Table 6 for more information). The VDRIVE pin
is connected to the supply voltage of the microprocessor. The
voltage applied to the VDRIVE input controls the voltage of the
serial interface. VDRIVE can be set to 3 V or 5 V.
+15V
+
10µF
10µF
VDD1
ANALOG INPUTS:
±10V, ±5V, ±2.5V,
0V TO +10V
PINS OMITTED FOR CLARITY.
04852-026
V–
1ADDITIONAL
Figure 33. Single-Ended Mode Typical Connection Diagram
True Differential Mode
The AD7328 can have four true differential analog input pairs.
Differential signals have some benefits over single-ended
signals, including better noise immunity based on the device’s
common-mode rejection and improvements in distortion
performance. Figure 34 defines the configuration of the true
differential analog inputs of the AD7328.
VIN+
AD73281
VIN–
10µF +
0.1µF
1ADDITIONAL
AD7328
PINS OMITTED FOR CLARITY.
Figure 34. True Differential Inputs
CS
DOUT
The amplitude of the differential signal is the difference
between the signals applied to the VIN+ and VIN− pins in
each differential pair (VIN+ − VIN−). VIN+ and VIN− should
be simultaneously driven by two signals of equal amplitude,
dependent on the input range selected, that are 180° out of
phase. Assuming the ±4 × VREF mode, the amplitude of
the differential signal is −20 V to +20 V p-p (2 × 4 × VREF),
regardless of the common mode.
µC/µP
SCLK
DIN
DGND
VSS1
SERIAL
INTERFACE
AGND
+
10µF
1MINIMUM
VDD AND VSS SUPPLY VOLTAGES
DEPEND ON THE HIGHEST ANALOG INPUT
RANGE SELECTED.
04852-025
–15V
0.1µF
VSS
+3V SUPPLY
REFIN/OUT
680nF
VDD VCC
AD73281
0.1µF
VCC
VDRIVE
VIN0
VIN1
VIN2
VIN3
VIN4
VIN5
VIN6
VIN7
VIN+
04852-027
0.1µF
AGND
VCC +2.7V TO +5.25V
+
5V
The common mode is the average of the two signals
Figure 32. Typical Connection Diagram
(VIN+ + VIN−)/2
ANALOG INPUT
Single-Ended Inputs
and is therefore the voltage on which the two input signals are
centered.
The AD7328 has a total of eight analog inputs when operating
in single-ended mode. Each analog input can be independently
programmed to one of the four analog input ranges. In applications
where the signal source is high impedance, it is recommended
to buffer the signal before applying it to the ADC analog inputs.
Figure 33 shows the configuration of the AD7328 in singleended mode.
This voltage is set up externally, and its range varies with reference
voltage. As the reference voltage increases, the common-mode
range decreases. When the differential inputs are driven with an
amplifier, the actual common-mode range is determined by the
amplifier’s output swing. If the differential inputs are not driven
from an amplifier, the common-mode range is determined by
the supply voltage on the VDD supply pin and the VSS supply pin.
When a conversion takes place, the common mode is rejected,
resulting in a noise-free signal of amplitude −2 × (4 × VREF) to
+2 × (4 × VREF), corresponding to Digital Codes −4096 to +4095.
Rev. C | Page 18 of 36
Data Sheet
AD7328
5
8
±5V RANGE
6
±5V RANGE
3
±2.5V
RANGE
4
VCOM RANGE (V)
VCOM RANGE (V)
2
1
0
±10V
RANGE
–1
–2
–3
±2.5V
RANGE
±10V
RANGE
±10V
RANGE
2
0
–2
–4
±5V RANGE
–4
VCC = 3V
VREF = 3V
–6
04852-045
–5
–6
±16.5V VDD/VSS
–8
±16.5V VDD/VSS
±12V VDD/VSS
Figure 38. Common-Mode Range for VCC = 5 V and REFIN/OUT = 2.5 V
8
Pseudo Differential Inputs
±5V RANGE
6
VCOM RANGE (V)
±2.5V
RANGE
VCC = 5V
VREF = 2.5V
±12V VDD/VSS
Figure 35. Common-Mode Range for VCC = 3 V and REFIN/OUT = 3 V
4
±5V RANGE
±2.5V
RANGE
±10V
RANGE
04852-048
4
The AD7328 can have four pseudo differential pairs or seven
pseudo differential inputs referenced to a common VIN− pin. The
VIN+ inputs are coupled to the signal source and must have an
amplitude within the selected range for that channel as programmed in the range register. A dc input is applied to the VIN− pin.
The voltage applied to this input provides an offset for the
VIN+ input from ground or a pseudo ground. Pseudo differential
inputs separate the analog input signal ground from the ADC
ground, allowing cancellation of dc common-mode voltages.
Figure 39 shows the configuration of the AD7328 in pseudo
differential mode.
±5V RANGE
±2.5V
RANGE
±2.5V
RANGE
±10V
RANGE
2
±10V
RANGE
0
–2
04852-046
VCC = 5V
VREF = 3V
–4
±16.5V VDD/VSS
±12V VDD/VSS
When a conversion takes place, the pseudo differential ground
corresponds to Code −4096, and the maximum amplitude
corresponds to Code +4095.
Figure 36. Common-Mode Range for VCC = 5 V and REFIN/OUT = 3 V
6
V+
4
±5V RANGE
5V
±5V RANGE
VIN+
0
–6
±10V
RANGE
±10V
±2.5V
RANGE RANGE
VIN–
VCC = 3V
VREF = 2.5V
–8
±16.5V VDD/VSS
VSS
±2.5V
RANGE
V–
1ADDITIONAL
PINS OMITTED FOR CLARITY.
04852-028
–2
–4
VDD VCC
AD73281
04852-047
VCOM RANGE (V)
2
Figure 39. Pseudo Differential Inputs
±12V VDD/VSS
Figure 37. Common-Mode Range for VCC = 3 V and REFIN/OUT = 2.5 V
Figure 40 and Figure 41 show the typical voltage range on the
VIN− pin for various analog input ranges when configured in
the pseudo differential mode.
For example, when the AD7328 is configured to operate in
pseudo differential mode and the ±5 V range is selected with
±16.5 V VDD/VSS supplies and 5 V VCC, the voltage on the
VIN− pin can vary from −6.5 V to +6.5 V.
Rev. C | Page 19 of 36
AD7328
Data Sheet
8
4
±2.5V
RANGE
2
0
–2
±10V
RANGE
–4
0V TO +10V
RANGE
VCC = 5V
VREF = 2.5V
0V TO +10V
RANGE
–8
Differential operation requires that VIN+ and VIN− be simultaneously driven with two signals of equal amplitude that are 180°
out of phase. The common mode must be set up externally to
the AD7328. The common-mode range is determined by the
REFIN/OUT voltage, the VCC supply voltage, and the particular
amplifier used to drive the analog inputs. Differential mode with
either an ac input or a dc input provides the best THD performance
over a wide frequency range. Because not all applications have a
signal preconditioned for differential operation, there is often a
need to perform a single-ended-to-differential conversion. This
single-ended-to-differential conversion can be performed using
an op amp pair. Typical connection diagrams for an op amp
pair are shown in Figure 42 and Figure 43. In Figure 42, the
common-mode signal is applied to the noninverting input of
the second amplifier.
04852-039
–6
±12V VDD/VSS
±16.5V VDD/VSS
Figure 40. Pseudo Differential Input Range with VCC = 5 V
4
±5V RANGE
±5V RANGE
2
±2.5V
RANGE
0
–2
±10V
RANGE
±10V
RANGE
0V TO +10V
RANGE
–6
0V TO +10V
RANGE
04852-040
–4
±2.5V
RANGE
VCC = 3V
VREF = 2.5V
–8
±16.5V VDD/VSS
1.5kΩ
2kΩ
±12V VDD/VSS
VIN
V+
Figure 41. Pseudo Differential Input Range with VCC = 3 V
DRIVER AMPLIFIER CHOICE
1.5kΩ
In applications where the harmonic distortion and signal-tonoise ratio are critical specifications, the analog input of the
AD7328 should be driven from a low impedance source. Large
source impedances significantly affect the ac performance of the
ADC and can necessitate the use of an input buffer amplifier.
1.5kΩ
V–
04852-029
When no amplifier is used to drive the analog input, the source
impedance should be limited to low values. The maximum source
impedance depends on the amount of THD that can be tolerated
in the application. The THD increases as the source impedance
increases and performance degrades. Figure 21 and Figure 22
show graphs of the THD vs. the analog input frequency for various
source impedances. Depending on the input range and analog
input configuration selected, the AD7328 can handle source
impedances of up to 4.7 kΩ before the THD starts to degrade.
1.5kΩ
1.5kΩ
10kΩ
Figure 42. Single-Ended-to-Differential Configuration with the AD845
442Ω
VIN
442Ω
AD8021
V+
442Ω
Due to the programmable nature of the analog inputs on the
AD7328, the choice of op amp used to drive the inputs is a
function of the particular application and depends on the input
configuration and the analog input voltage ranges selected.
442Ω
442Ω
442Ω
V–
AD8021
100Ω
04852-030
6
The driver amplifier must be able to settle for a full-scale step
to a 13-bit level, 0.0122%, in less than the specified acquisition
time of the AD7328. An op amp such as the AD8021 meets this
requirement when operating in single-ended mode. The AD8021
needs an external compensating NPO type of capacitor. The
AD8022 can also be used in high frequency applications where
a dual version is required. For lower frequency applications, op
amps such as the AD797, AD845, and AD8610 can be used with
the AD7328 in single-ended mode configuration.
±5V RANGE
±5V RANGE
±2.5V
RANGE
±10V
RANGE
Figure 43. Single-Ended-to-Differential Configuration with the AD8021
Rev. C | Page 20 of 36
Data Sheet
AD7328
REGISTERS
The AD7328 has four programmable registers: the control register, sequence register, Range Register 1, and Range Register 2. These
registers are write-only registers.
ADDRESSING REGISTERS
A serial transfer on the AD7328 consists of 16 SCLK cycles. The three MSBs on the DIN line during the 16 SCLK transfer are decoded to
determine which register is addressed. The three MSBs consist of the write bit, the Register Select 1 bit, and the Register Select 2 bit. The
register select bits are used to determine which of the four on-board registers is selected. The write bit determines if the data on the DIN
line following the register select bits loads into the addressed register. If the write bit is 1, the bits load into the register addressed by the
register select bits. If the write bit is 0, the data on the DIN line does not load into any register.
Combinations of the write bit, the Register Select 1 bit, and the Register Select 2 bit other than those specified in Table 8 access registers
for Analog Devices internal use only. Do not access these registers, as doing so may lead to unspecified operation of the device.
Table 8. Decoding Register Select Bits and Write Bit
Write
0
1
Register Select 1
0
0
Register Select 2
0
0
1
0
1
1
1
0
1
1
1
Description
Data on the DIN line during this serial transfer is ignored.
This combination selects the control register. The subsequent 12 bits are loaded into
the control register.
This combination selects Range Register 1. The subsequent 8 bits are loaded into
Range Register 1.
This combination selects Range Register 2. The subsequent 8 bits are loaded into
Range Register 2.
This combination selects the sequence register. The subsequent 8 bits are loaded into
the sequence register.
Rev. C | Page 21 of 36
AD7328
Data Sheet
CONTROL REGISTER
The control register is used to select the analog input channel, analog input configuration, reference, coding, and power mode. The control
register is a write-only, 12-bit register. Data loaded on the DIN line corresponds to the AD7328 configuration for the next conversion. If the
sequence register is being used, data should be loaded into the control register after the range registers and the sequence register have been
initialized. The bit functions of the control register are described in Table 9 (the power-up status of all bits is 0).
MSB
15
Write
14
Register
Select 1
13
Register
Select 2
12
ADD2
11
ADD1
10
ADD0
9
Mode 1
8
Mode 0
7
PM1
6
PM0
5
Coding
4
REF
3
SEQ1
2
SEQ2
1
Weak/
Three-State
LSB
0
0
Table 9. Control Register Details
Bit
12, 11, 10
Mnemonic
ADD2, ADD1,
ADD0
9, 8
Mode 1, Mode 0
7, 6
5
PM1, PM0
Coding
4
REF
3, 2
1
SEQ1/SEQ2
Weak/Three-State
Description
These three channel address bits are used to select the analog input channel for the next conversion if the
sequencer is not being used. If the sequencer is being used, the three channel address bits are used to
select the final channel in a consecutive sequence.
These two mode bits are used to select the configuration of the eight analog input pins, VIN0 to VIN7. These
pins are used in conjunction with the channel address bits. On the AD7328, the analog inputs can be configured
as eight single-ended inputs, four fully differential input pairs, four pseudo differential inputs, or seven
pseudo differential inputs (see Table 10).
The power management bits are used to select different power mode options on the AD7328 (see Table 11).
This bit is used to select the type of output coding that the AD7328 uses for the next conversion result.
If coding = 0, the output coding is twos complement. If coding = 1, the output coding is straight binary.
When operating in sequence mode, the output coding for each channel is the value written to the coding
bit during the last write to the control register.
The reference bit is used to enable or disable the internal reference. If REF = 0, the external reference is
enabled and used for the next conversion, and the internal reference is disabled. If REF = 1, the internal reference is used for the next conversion. When operating in sequence mode, the reference used for each
channel is the value written to the REF bit during the last write to the control register.
The Sequence 1 and Sequence 2 bits are used to control the operation of the sequencer (see Table 12).
This bit selects the state of the DOUT line at the end of the current serial transfer. If the bit is set to 1, the
DOUT line is weakly driven to Channel Address Bit ADD2 of the following conversion. If this bit is set to 0,
DOUT returns to three-state at the end of the serial transfer (see the Serial Interface section).
The eight analog input channels can be configured as seven pseudo differential analog inputs, four pseudo differential inputs, four true
differential input pairs, or eight single-ended analog inputs.
Table 10. Analog Input Configuration Selection
Channel Address Bits
ADD2 ADD1 ADD0
0
0
0
0
0
1
0
1
0
0
1
1
1
0
0
1
0
1
1
1
0
1
1
1
7 Pseudo Differential I/Ps
(Mode 1 = 1, Mode 0 = 1)
VIN+
VIN−
VIN0
VIN7
VIN1
VIN7
VIN2
VIN7
VIN3
VIN7
VIN4
VIN7
VIN5
VIN7
VIN6
VIN7
Temperature indicator
4 Fully Differential I/Ps
(Mode 1 = 1, Mode 0 = 0)
VIN+
VIN−
VIN0
VIN1
VIN0
VIN1
VIN2
VIN3
VIN2
VIN3
VIN4
VIN5
VIN4
VIN5
VIN6
VIN7
VIN6
VIN7
Rev. C | Page 22 of 36
4 Pseudo Differential I/Ps
(Mode 1 = 0, Mode 0 = 1)
VIN+
VIN−
VIN0
VIN1
VIN0
VIN1
VIN2
VIN3
VIN2
VIN3
VIN4
VIN5
VIN4
VIN5
VIN6
VIN7
VIN6
VIN7
8 Single-Ended I/Ps
(Mode 1 = 0, Mode 0 = 0)
VIN+
VIN−
VIN0
AGND
VIN1
AGND
VIN2
AGND
VIN3
AGND
VIN4
AGND
VIN5
AGND
VIN6
AGND
VIN7
AGND
Data Sheet
AD7328
Table 11. Power Mode Selection
PM1
1
PM0
1
1
0
0
1
0
0
Description
Full shutdown mode. In this mode, all internal circuitry on the AD7328 is powered down. Information in the control
register is retained when the AD7328 is in full shutdown mode.
Autoshutdown mode. The AD7328 enters autoshutdown on the 15th SCLK rising edge when the control register is
updated. All internal circuitry is powered down in autoshutdown.
Autostandby mode. In this mode, all internal circuitry is powered down, excluding the internal reference. The AD7328
enters autostandby mode on the 15th SCLK rising edge after the control register is updated.
Normal mode. All internal circuitry is powered up at all times.
Table 12. Sequencer Selection
SEQ1
0
SEQ2
0
0
1
1
0
1
1
Description
The channel sequencer is not used. The analog channel, selected by programming the ADD2 to ADD0 bits in the control
register, selects the next channel for conversion.
Uses the sequence of channels that were previously programmed in the sequence register for conversion. The AD7328
starts converting on the lowest channel in the sequence. The channels are converted in ascending order. If uninterrupted,
the AD7328 keeps converting the sequence. The range for each channel defaults to the range previously written into the
corresponding range register.
This configuration is used in conjunction with the channel address bits in the control register. This allows continuous conversions
on a consecutive sequence of channels, from Channel 0 through a final channel selected by the channel address bits in the
control register. The range for each channel defaults to the range previously written into the corresponding range register.
The channel sequencer is not used. The analog channel, selected by programming the ADD2 bit to ADD0 bit in the control
register, selects the next channel for conversion.
Rev. C | Page 23 of 36
AD7328
Data Sheet
SEQUENCE REGISTER
The sequence register on the AD7328 is an 8-bit, write-only register. Each of the eight analog input channels has one corresponding bit in
the sequence register. To select a channel for inclusion in the sequence, set the corresponding channel bit to 1 in the sequence register.
MSB
16
Write
15
Register Select 1
14
Register Select 2
13
VIN0
12
VIN1
11
VIN2
10
VIN3
9
VIN4
8
VIN5
7
VIN6
6
VIN7
5
0
4
0
3
0
2
0
LSB
1
0
RANGE REGISTERS
The range registers are used to select one analog input range per analog input channel. Range Register 1 is used to set the ranges for
Channel 0 to Channel 3. It is an 8-bit, write-only register with two dedicated range bits for each of the analog input channels from Channel 0 to
Channel 3. There are four analog input ranges, ±10 V, ±5 V, ±2.5 V, and 0 V to +10 V. A write to Range Register 1 is selected by setting the
write bit to 1 and the range select bits to 0 and 1, respectively. After the initial write to Range Register 1 occurs, each time an analog input
is selected, the AD7328 automatically configures the analog input to the appropriate range, as indicated by Range Register 1. The ±10 V
input range is selected by default on each analog input channel (see Table 13).
MSB
16
Write
15
Register Select 1
14
Register Select 2
13
VIN0A
12
VIN0B
11
VIN1A
10
VIN1B
9
VIN2A
8
VIN2B
7
VIN3A
6
VIN3B
5
0
4
0
3
0
2
0
LSB
1
0
Range Register 2 is used to set the ranges for Channel 4 to Channel 7. It is an 8-bit, write-only register with two dedicated range bits for
each of the analog input channels from Channel 4 to Channel 7. There are four analog input ranges, ±10 V, ±5 V, ±2.5 V, and 0 V to +10 V.
After the initial write to Range Register 2 occurs, each time an analog input is selected, the AD7328 automatically configures the analog
input to the appropriate range, as indicated by Range Register 2. The ±10 V input range is selected by default on each analog input channel
(see Table 13).
MSB
16
Write
15
Register Select 1
14
Register Select 2
13
VIN4A
12
VIN4B
11
VIN5A
10
VIN5B
9
VIN6A
Table 13. Range Selection
VINxA
0
0
1
1
VINxB
0
1
0
1
Description
This combination selects the ±10 V input range on VINx.
This combination selects the ±5 V input range on VINx.
This combination selects the ±2.5 V input range on VINx.
This combination selects the 0 V to +10 V input range on VINx.
Rev. C | Page 24 of 36
8
VIN6B
7
VIN7A
6
VIN7B
5
0
4
0
3
0
2
0
LSB
1
0
Data Sheet
AD7328
SEQUENCER OPERATION
POWER ON.
CS
DIN: WRITE TO RANGE REGISTER 1 TO SELECT THE RANGE
FOR EACH ANALOG INPUT CHANNEL.
DOUT: CONVERSION RESULT FROM CHANNEL 0, ± 10V
RANGE, SINGLE-ENDED MODE.
CS
DIN: WRITE TO RANGE REGISTER 2 TO SELECT THE RANGE
FOR EACH ANALOG INPUT CHANNEL.
DOUT: CONVERSION RESULT FROM CHANNEL 0,
SINGLE-ENDED MODE, RANGE SELECTED IN
RANGE REGISTER 1.
CS
DIN: WRITE TO SEQUENCE REGISTER TO SELECT THE
ANALOG INPUT CHANNELS TO BE INCLUDED IN
THE SEQUENCE.
DOUT: CONVERSION RESULT FROM CHANNEL 0,
SINGLE-ENDED MODE, RANGE SELECTED IN
RANGE REGISTER 1.
CS
DIN: WRITE TO CONTROL REGISTER TO START THE
SEQUENCE, SEQ1 = 0, SEQ2 = 1.
DOUT: CONVERSION RESULT FROM CHANNEL 0,
SINGLE-ENDED MODE, RANGE SELECTED IN
RANGE REGISTER 1.
CS
DIN: TIE DIN LOW/WRITE BIT = 0 TO CONTINUE TO CONVERT
THROUGH THE SEQUENCE OF CHANNELS.
CS
DOUT: CONVERSION RESULT FROM FIRST CHANNEL IN
THE SEQUENCE.
DIN: WRITE TO CONTROL
REGISTER TO STOP THE
SEQUENCE, SEQ1 = 0, SEQ2 = 0.
STOPPING
A SEQUENCE.
DOUT: CONVERSION RESULT
FROM CHANNEL IN SEQUENCE.
DIN TIED LOW/WRITE BIT = 0.
CONTINUOUSLY CONVERT
ON THE SELECTED SEQUENCE
OF CHANNELS.
SELECTING A NEW SEQUENCE.
CS
DIN: WRITE TO SEQUENCE REGISTER TO SELECT THE
NEW SEQUENCE.
04852-031
DOUT: CONVERSION RESULT FROM CHANNEL X IN
THE FIRST SEQUENCE.
Figure 44. Programmable Sequence Flowchart
The AD7328 can be configured to automatically cycle through a
number of selected channels using the on-chip sequence register
with the SEQ1 bit and the SEQ2 bit in the control register. Figure 44
shows how to program the AD7328 register to operate in
sequence mode.
After power-up, all four on-chip registers contain default values.
Each analog input has a default input range of ±10 V. If different
analog input ranges are required, a write to the range registers is
necessary. This is shown in the first two serial transfers of Figure 44.
These two initial serial transfers are required only if input ranges
other than the default ranges are required. After the analog input
ranges are configured, a write to the sequence register is necessary
to select the channels to be included in the sequence. After the
channels for the sequence have been selected, the sequence can
be initiated by writing to the control register and setting SEQ1
to 0 and SEQ2 to 1. The AD7328 continues to convert the selected
sequence without interruption if the sequence register remains
unchanged and SEQ1 = 0 and SEQ2 = 1 in the control register.
Rev. C | Page 25 of 36
AD7328
Data Sheet
If a write to one of the range registers is required during a sequence, it is necessary to first stop the sequence by writing to
the control register and setting SEQ1 to 0 and SEQ2 to 0. Next,
write to the range register to change the required range. The
previously selected sequence should then be initiated again by
writing to the control register and setting SEQ1 to 0 and SEQ2
to 1. The ADC converts the first channel in the sequence.
The AD7328 can be configured to convert a sequence of consecutive channels (see Figure 45). This sequence begins by
converting on Channel 0 and ends with a final channel as selected
by Bit ADD2 to Bit ADD0 in the control register. In this configuration, there is no need for a write to the sequence register. To
operate the AD7328 in this mode, set SEQ1 to 1 and SEQ2 to 0
in the control register, and then select the final channel in the
sequence by programming Bit ADD2 to Bit ADD0 in the control
register.
After the control register is configured to operate the AD7328
in this mode, the DIN line can be held low or the write bit can
be set to 0. To return to traditional multichannel operation, a
write to the control register to set SEQ1 to 0 and SEQ2 to 0 is
necessary.
When SEQ1 and SEQ2 are both set to 0 or to 1, the AD7328 is
configured to operate in traditional multichannel mode, where
a write to Channel Address Bit ADD2 to Bit ADD0 in the
control register selects the next channel for conversion.
POWER ON.
CS
DIN: WRITE TO RANGE REGISTER 1 TO SELECT THE RANGE
FOR ANALOG INPUT CHANNELS.
DOUT: CONVERSION RESULT FROM CHANNEL 0, ± 10V
RANGE, SINGLE-ENDED MODE.
CS
DIN: WRITE TO RANGE REGISTER 2 TO SELECT THE RANGE
FOR ANALOG INPUT CHANNELS.
DOUT: CONVERSION RESULT FROM CHANNEL 0,
RANGE SELECTED IN RANGE REGISTER 1,
SINGLE-ENDED MODE.
CS
DIN: WRITE TO CONTROL REGISTER TO SELECT THE FINAL
CHANNEL IN THE CONSECUTIVE SEQUENCE, SET SEQ1 = 1
AND SEQ2 = 0. SELECT OUTPUT CODING FOR SEQUENCE.
DOUT: CONVERSION RESULT FROM CHANNEL 0,
RANGE SELECTED IN RANGE REGISTER 1,
SINGLE-ENDED MODE.
CS
DIN: WRITE BIT = 0 OR DIN LINE HELD LOW TO CONTINUE
TO CONVERT THROUGH THE SEQUENCE OF
CONSECUTIVE CHANNELS.
DOUT: CONVERSION RESULT FROM CHANNEL 0,
RANGE SELECTED IN RANGE REGISTER 1.
CS
DIN: WRITE BIT = 0 OR DIN LINE HELD LOW TO CONTINUE
THROUGH SEQUENCE OF CONSECUTIVE CHANNELS.
DOUT: CONVERSION RESULT FROM CHANNEL 1,
RANGE SELECTED IN RANGE REGISTER 1.
STOPPING
A SEQUENCE.
DIN TIED LOW/WRITE BIT = 0.
CONTINUOUSLY CONVERT
ON CONSECUTIVE SEQUENCE
OF CHANNELS.
CS
DOUT: CONVERSION RESULT
FROM CHANNEL IN SEQUENCE.
Figure 45. Flowchart for Consecutive Sequence of Channels
Rev. C | Page 26 of 36
04852-032
DIN: WRITE TO CONTROL
REGISTER TO STOP THE
SEQUENCE, SEQ1 = 0, SEQ2 = 0.
Data Sheet
AD7328
On power-up, if the internal reference operation is required for
the ADC conversion, a write to the control register is necessary
to set the REF bit to 1. During the control register write, the conversion result from the first initial conversion is invalid. The
reference buffer requires 500 µs to power up and charge the
680 nF decoupling capacitor during the power-up time.
4420
4400
±10V RANGE, INT REF
4390
4380
4370
4360
4350
The AD7328 is specified for a 2.5 V to 3 V reference range. When
a 3 V reference is selected, the ranges are ±12 V, ±6 V, ±3 V, and
0 V to +12 V. For these ranges, the VDD and VSS supply must be
equal to or greater than the maximum analog input range selected.
4340
–40
5400
ADC OUTPUT CODE
The AD7328 has a VDRIVE feature to control the voltage at which
the serial interface operates. VDRIVE allows the ADC to easily
interface to both 3 V and 5 V processors. For example, if the
AD7328 is operated with a VCC of 5 V, the VDRIVE pin can be
powered from a 3 V supply. This allows the AD7328 to accept
large bipolar input signals with low voltage digital processing.
Rev. C | Page 27 of 36
0
40
20
60
80
100
Figure 46. ADC Output Code vs. Temperature for ±10 V Range
VDRIVE
The AD7328 has an on-chip temperature indicator. The temperature indicator can be used to provide local temperature
measurements on the AD7328. To access the temperature indicator,
the ADC should be configured in pseudo differential mode,
Mode 1 = Mode 0 = 1, which sets Channel Bits ADD2, ADD1,
–20
TEMPERATURE (°C)
5450
TEMPERATURE INDICATOR
VCC = VDRIVE = 5V
VDD/VSS = ±12V
50kSPS
4410
04852-033
The internal reference circuitry consists of a 2.5 V band gap
reference and a reference buffer. When operating the AD7328
in internal reference mode, the 2.5 V internal reference is available
at the REFIN/OUT pin, which should be decoupled to AGND
using a 680 nF capacitor. It is recommended that the internal
reference be buffered before applying it elsewhere in the system.
The internal reference is capable of sourcing up to 90 μA.
VCC = VDRIVE = 5V
VDD/VSS = ±12V
±2.5V RANGE
INT REFERENCE
30kSPS
5350
5300
5250
5200
5150
5100
–40
04852-034
The AD7328 can operate with either the internal 2.5 V on-chip
reference or an externally applied reference. The internal reference
is selected by setting the REF bit in the control register to 1. On
power-up, the REF bit is 0, which selects the external reference for
the AD7328 conversion. Suitable reference sources for the AD7328
include AD780, AD1582, ADR431, REF193, and ADR391.
and ADD0 to 1. VIN7 must be tied to AGND or to a small dc
voltage within the specified pseudo differential input range for
the selected analog input range. When a conversion is initiated in
this configuration, the output code represents the temperature
(see Figure 46 and Figure 47). When using the temperature
indicator on the AD7328, the part should be operated at low
throughput rates, such as approximately 50 kSPS for the ±10 V
range and 30 kSPS for the ±2.5 V range. The throughput rate is
reduced for the temperature indicator mode because the AD7328
requires more acquisition time for this mode.
ADC OUTPUT CODE
REFERENCE
–20
0
20
40
60
80
TEMPERATURE (°C)
Figure 47. ADC Output Code vs. Temperature for ±2.5 V Range
AD7328
Data Sheet
MODES OF OPERATION
The AD7328 has several modes of operation that are designed
to provide flexible power management options. These options
can be chosen to optimize the power dissipation/throughput
rate ratio for different application requirements. The mode of
operation of the AD7328 is controlled by the power management
bits, Bit PM1 and Bit PM0, in the control register as shown in
Table 11. The default mode is normal mode, where all internal
circuitry is fully powered up.
The AD7328 remains fully powered up at the end of the conversion if both PM1 and PM0 contain 0 in the control register.
NORMAL MODE
(PM1 = PM0 = 0)
FULL SHUTDOWN MODE
(PM1 = PM0 = 1)
This mode is intended for the fastest throughput rate performance with the AD7328 being fully powered up at all times.
Figure 48 shows the general operation of the AD7328 in
normal mode.
In this mode, all internal circuitry on the AD7328 is powered
down. The part retains information in the registers during full
shutdown. The AD7328 remains in full shutdown mode until
the power management bits, Bit PM1 and Bit PM0, in the control
register are changed.
To complete the conversion and access the conversion result
16 serial clock cycles are required. At the end of the conversion,
CS can idle either high or low until the next conversion.
Once the data transfer is complete, another conversion can be
initiated after the quiet time, tQUIET, has elapsed.
The conversion is initiated on the falling edge of CS, and the trackand-hold enters hold mode, as described in the Serial Interface
section. The data on the DIN line during the 16 SCLK transfer
is loaded into one of the on-chip registers if the write bit is set.
The register is selected by programming the register select bits
(see Table 8).
A write to the control register with PM1 = PM0 = 1 places the
part into full shutdown mode. The AD7328 enters full shutdown mode on the 15th SCLK rising edge when the control register
is updated.
If a write to the control register occurs while the part is in full
shutdown mode with the power management bits, Bit PM1 and
Bit PM0, set to 0 (normal mode), the part begins to power up
on the 15th SCLK rising edge when the control register is updated.
Figure 49 shows how the AD7328 is configured to exit full shutdown mode. To ensure that the AD7328 is fully powered up,
tPOWER-UP should elapse before the next CS falling edge.
CS
1
16
SCLK
DOUT
04852-035
3 CHANNEL I.D. BITS, SIGN BIT + CONVERSION RESULT
DATA INTO CONTROL/SEQUENCE/RANGE1/RANGE2
REGISTER
DIN
Figure 48. Normal Mode
PART IS IN FULL
SHUTDOWN
THE PART IS FULLY POWERED UP
ONCE tPOWER-UP HAS ELAPSED
PART BEGINS TO POWER UP ON THE 15TH
SCLK RISING EDGE AS PM1 = PM0 = 0
tPOWER-UP
CS
1
16
1
16
SDATA
DIN
INVALID DATA
CHANNEL IDENTIFIER BITS + CONVERSION RESULT
DATA INTO CONTROL REGISTER
DATA INTO CONTROL REGISTER
CONTROL REGISTER IS LOADED ON THE FIRST 15 CLOCKS,
PM1 = 0, PM0 = 0
TO KEEP THE PART IN NORMAL MODE, LOAD PM1 = PM0 = 0
IN CONTROL REGISTER
Figure 49. Exiting Full Shutdown Mode
Rev. C | Page 28 of 36
04852-041
SCLK
Data Sheet
AD7328
AUTOSHUTDOWN MODE
(PM1 = 1, PM0 = 0)
AUTOSTANDBY MODE
(PM1 = 0, PM0 = 1)
Once the autoshutdown mode is selected, the AD7328 automatically enters shutdown on the 15th SCLK rising edge. In
autoshutdown mode, all internal circuitry is powered down.
The AD7328 retains information in the registers during
autoshutdown. The track-and-hold is in hold mode during
autoshutdown. On the rising CS edge, the track-and-hold,
which was in hold during shutdown, returns to track as the
AD7328 begins to power up. The time to power-up from autoshutdown is 500 µs.
In autostandby mode, portions of the AD7328 are powered
down, but the on-chip reference remains powered up. The
reference bit in the control register should be 1 to ensure that
the on-chip reference is enabled. This mode is similar to autoshutdown but allows the AD7328 to power up much faster,
which allows faster throughput rates.
When the control register is programmed to transition to
autoshutdown mode, it does so on the 15th SCLK rising edge.
Figure 50 shows the part entering the autoshutdown mode.
When the AD7328 is in autoshutdown mode, the CS signal
must remain low to keep the part in autoshutdown mode. The
AD7328 automatically begins to power up on the CS rising edge.
The tPOWER-UP is required before a valid conversion, initiated by
bringing the CS signal low, can take place. After this valid conversion is complete, the AD7328 powers down again on the 15th
SCLK rising edge. The CS signal must remain low to keep the
part in autoshutdown mode.
As is the case with autoshutdown mode, the AD7328 enters
standby on the 15th SCLK rising edge when the control register
is updated (see Figure 50). The part retains information in the
registers during standby. The AD7328 remains in standby until
it receives a CS rising edge. The ADC begins to power up on the
CS rising edge. On the CS rising edge, the track-and-hold,
which was in hold mode while the part was in standby, returns
to track.
The power-up time from standby is 700 ns. The user should
ensure that 700 ns have elapsed before bringing CS low to
attempt a valid conversion. After this valid conversion is
complete, the AD7328 again returns to standby on the 15th
SCLK rising edge. The CS signal must remain low to keep the
part in standby mode.
Figure 50 shows the part entering autoshutdown mode. The
sequence of events is the same when entering autostandby mode.
In Figure 50, the power management bits are configured for autoshutdown. For autostandby mode, the power management bits,
PM1 and PM0, should be set to 0 and 1, respectively.
PART BEGINS TO POWER
UP ON CS RISING EDGE
PART ENTERS SHUTDOWN MODE
ON THE 15TH RISING SCLK EDGE
AS PM1 = 1, PM0 = 0
CS
1
THE PART IS FULLY POWERED UP
ONCE tPOWER-UP HAS ELAPSED
tPOWER-UP
15 16
1
15 16
SCLK
DIN
VALID DATA
VALID DATA
DATA INTO CONTROL REGISTER
DATA INTO CONTROL REGISTER
04852-042
SDATA
CONTROL REGISTER IS LOADED ON THE FIRST 15 CLOCKS,
PM1 = 1, PM0 = 0
Figure 50. Entering Autoshutdown/Autostandby Mode
Rev. C | Page 29 of 36
AD7328
Data Sheet
POWER VS. THROUGHPUT RATE
20
The power consumption of the AD7328 varies with the throughput
rate. The static power consumed by the AD7328 is very low, and
significant power savings can be achieved as the throughput rate is
reduced. Figure 51 and Figure 52 show the power vs. throughput
rate for the AD7328 at a VCC of 3 V and 5 V, respectively. Both
plots clearly show that the average power consumed by the AD7328
is greatly reduced as the sample frequency is reduced. This is true
whether a fixed SCLK value is used or the SCLK value is scaled
with the sampling frequency. Figure 51 and Figure 52 show the
power consumption when operating the device in normal mode
for a fixed 20 MHz SCLK and a variable SCLK that scales with
the sampling frequency.
18
12
20MHz SCLK
12
10
8
6
4
VCC = 5V
VDD/VSS = ±12V
TA = 25°C
INTERNAL REFERENCE
2
0
0
100
200
300
400
500
600
700
800
900
THROUGHPUT RATE (kHz)
20MHz SCLK
8
VARIABLE SCLK
6
VCC = 3V
VDD/VSS = ±12V
TA = 25°C
INTERNAL REFERENCE
2
0
0
100
200
300
400
500
600
700
800
04852-052
4
900 1000 1100
THROUGHPUT RATE (kSPS)
Figure 51. Power vs. Throughput Rate with 3 V VCC
Rev. C | Page 30 of 36
04852-053
AVERAGE POWER (mW)
VARIABLE SCLK
14
Figure 52. Power vs. Throughput Rate with 5 V VCC
10
AVERAGE POWER (mW)
16
1000
Data Sheet
AD7328
SERIAL INTERFACE
Figure 53 shows the timing diagram for the serial interface of
the AD7328. The serial clock applied to the SCLK pin provides
the conversion clock and controls the transfer of information to
and from the AD7328 during a conversion.
The CS signal initiates the data transfer and the conversion
process. The falling edge of CS puts the track-and-hold into
hold mode and takes the bus out of three-state. The analog
input signal is then sampled. After the conversion is initiated, 16
SCLK cycles are required for the conversion to complete.
The track-and-hold goes back into track mode on the 14th SCLK
rising edge. On the 16th SCLK falling edge, the DOUT line returns
to three-state. If the rising edge of CS occurs before 16 SCLK cycles
have elapsed, the conversion is terminated and the DOUT line
returns to three-state. Depending on where the CS signal is brought
high, the addressed register may update.
Data is clocked into the AD7328 on the SCLK falling edge. The
three MSBs on the DIN line are decoded to select which register
is addressed. The control register is a 12-bit register. If the control
register is addressed by the three MSBs, the data on the DIN line
is loaded into the control on the 15th SCLK rising edge. If the sequence register or either of the range registers is addressed, the
data on the DIN line is loaded into the addressed register on the
11th SCLK falling edge.
Conversion data is clocked out of the AD7328 on each SCLK
falling edge. Data on the DOUT line consists of three channel
identifier bits, a sign bit, and a 12-bit conversion result. The
channel identifier bits are used to indicate which channel
corresponds to the conversion result.
If the Weak/Three-State bit is set in the control register, rather
than returning to true three-state upon the 16th SCLK falling
edge, the DOUT line is pulled weakly to the logic level corresponding to ADD3 of the next serial transfer. This is done to
ensure that the MSB of the next serial transfer is set up in time
for the first SCLK falling edge after the CS falling edge. If the
Weak/Three-State bit is set to 0 and the DOUT line returns to
true three-state between conversions, then depending on the
particular processor interfacing to the AD7328, the ADD3 bit
may be valid in time for the processor to clock it in successfully.
If the Weak/Three-State bit is set to 1, then although the DOUT
line has been driven to ADD3 since the previous conversion, it
is nevertheless so weakly driven that another device could take
control of the bus. This will not lead to a bus contention issue
because, for example, a 10 kΩ pull-up or pull-down resistor is
sufficient to overdrive the logic level of ADD3. When the Weak/
Three-State bit is set to 1, the ADD3 is typically valid 9 ns after
the CS falling edge, compared with 14 ns when the DOUT line
returns to three-state at the end of the conversion.
t1
CS
tCONVERT
t2
1
2
3
4
3 IDENTIFICATION BITS
t3
ADD1
DOUT
THREE- ADD2
t9
STATE
DIN
WRITE
REG
SEL1
ADD0
SIGN
5
t4
13
14
DB11
15
16
t5
t7
DB10
DB2
t8
DB1
t10
REG
SEL2
tQUIET
DB0
THREE-STATE
MSB
LSB
DON’T
CARE
Figure 53. Serial Interface Timing Diagram (Control Register Write)
Rev. C | Page 31 of 36
04852-036
SCLK
t6
AD7328
Data Sheet
MICROPROCESSOR INTERFACING
The serial interface on the AD7328 allows the part to be directly
connected to a range of different microprocessors. This section
explains how to interface the AD7328 with some common
microcontroller and DSP serial interface protocols.
AD7328 TO ADSP-21xx
The ADSP-21xx family of DSPs interfaces directly to the AD7328
without requiring glue logic. The VDRIVE pin of the AD7328 takes
the same supply voltage as that of the ADSP-21xx. This allows
the ADC to operate at a higher supply voltage than its serial interface. The SPORT0 on the ADSP-21xx should be configured as
shown in Table 14.
Table 14. SPORT0 Control Register Setup
Description
Alternative framing
Active low frame signal
Right justify data
16-bit data-word
Internal serial clock
Frame every word
Internal receive frame sync
Internal transmit frame sync
For example, if the ADSP-21xx has a master clock frequency of
16 MHz and the SCLKDIV register is loaded with the value 3,
an SCLK of 2 MHz is obtained, and eight master clock periods
elapse for every one SCLK period. If the timer registers are loaded
with the value 803, 100.5 SCLKs occur between interrupts and,
subsequently, between transmit instructions. This situation leads
to nonequidistant sampling because the transmit instruction occurs
on an SCLK edge. If the number of SCLKs between interrupts is
an integer of N, equidistant sampling is implemented by the DSP.
AD7328 TO ADSP-BF53x
The ADSP-BF53x family of DSPs interfaces directly to the
AD7328 without requiring glue logic, as shown in Figure 55.
The SPORT0 Receive Configuration 1 register should be set up
as outlined in Table 15.
ADSP-BF53x1
AD73281
The connection diagram is shown in Figure 54. The ADSP-21xx
has TFS0 and RFS0 tied together. TFS0 is set as an output, and
RFS0 is set as an input. The DSP operates in alternative framing
mode, and the SPORT0 control register is set up as described in
Table 14. The frame synchronization signal generated on TFS is
tied to CS and, as with all signal processing applications, requires
equidistant sampling. However, as in this example, the timer
interrupt is used to control the sampling rate of the ADC, and
under certain conditions equidistant sampling cannot be achieved.
SCLK
SCLK
CS
RFS0
DIN
DT0
DOUT
DR0
VDRIVE
VDD
1ADDITIONAL PINS OMITTED FOR CLARITY.
ADSP-21xx1
AD73281
RSCLK0
04852-038
Setting
TFSW = RFSW = 1
INVRFS = INVTFS = 1
DTYPE = 00
SLEN = 1111
ISCLK = 1
TFSR = RFSR = 1
IRFS = 0
ITFS = 1
The frequency of the serial clock is set in the SCLKDIV register.
When the instruction to transmit with TFS is given (AX0 = TX0),
the state of the serial clock is checked. The DSP waits until the
SCLK has gone high, low, and high again before starting the transmission. If the timer and SCLK are chosen so that the instruction
to transmit occurs on or near the rising edge of SCLK, data can
be transmitted immediately or at the next clock edge.
Figure 55. Interfacing the AD7328 to the ADSP-BF53x
SCLK0
CS
TFS0
RFS0
DIN
DT0
DOUT
DR0
Table 15. SPORT0 Receive Configuration 1 Register
VDD
1ADDITIONAL PINS OMITTED FOR CLARITY.
04852-037
VDRIVE
Figure 54. Interfacing the AD7328 to the ADSP-21xx
The timer registers are loaded with a value that provides an
interrupt at the required sampling interval. When an interrupt
is received, a value is transmitted with TFS/DT (ADC control
word). The TFS is used to control the RFS and, hence, the reading
of data.
Setting
RCKFE = 1
LRFS = 1
RFSR = 1
IRFS = 1
RLSBIT = 0
RDTYPE = 00
IRCLK = 1
RSPEN = 1
SLEN = 1111
TFSR = RFSR = 1
Rev. C | Page 32 of 36
Description
Sample data with falling edge of RSCLK
Active low frame signal
Frame every word
Internal RFS used
Receive MSB first
Zero fill
Internal receive clock
Receive enable
16-bit data-word
Transmit and receive frame sync
Data Sheet
AD7328
LAYOUT AND GROUNDING
The printed circuit board that houses the AD7328 should be
designed so that the analog and digital sections are confined to
certain areas of the board. This design facilitates the use of ground
planes that can be easily separated.
To provide optimum shielding for ground planes, a minimum
etch technique is generally best. All AGND pins on the AD7328
should be connected to the AGND plane. Digital and analog
ground pins should be joined in only one place. If the AD7328
is in a system where multiple devices require an AGND and
DGND connection, the connection should still be made at only
one point. A star point should be established as close as possible
to the ground pins on the AD7328.
These low ESR, low ESI capacitors provide a low impedance
path to ground at high frequencies to handle transient currents
due to internal logic switching.
POWER SUPPLY CONFIGURATION
It is recommended that Schottky diodes be placed in series with
the AD7328 VDD and VSS supply signals. Figure 56 shows this
Schottky diode configuration. BAT43 Schottky diodes are used.
VIN0
To avoid radiating noise to other sections of the board, components, such as clocks, with fast switching signals should be
shielded with digital ground and never run near the analog inputs.
Avoid crossover of digital and analog signals. To reduce the effects
of feedthrough within the board, traces should be run at right
angles to each other. A microstrip technique is the best method,
but its use may not be possible with a double-sided board. In
this technique, the component side of the board is dedicated to
ground planes, and signals are placed on the other side.
Good decoupling is also important. All analog supplies should
be decoupled with 10 µF tantalum capacitors in parallel with
0.1 µF capacitors to AGND. To achieve the best results from
these decoupling components, they must be placed as close as
possible to the device, ideally right up against the device. The
0.1 µF capacitors should have a low effective series resistance
(ESR) and low effective series inductance (ESI), such as is typical
of common ceramic and surface-mount types of capacitors.
3V/5V
VDD
VCC
AD73281
CS
SCLK
DOUT
VIN7
Good connections should be made to the power and ground
planes. This can be done with a single via or multiple vias for
each supply and ground pin.
Avoid running digital lines under the AD7328 device because
this couples noise onto the die. However, the analog ground
plane should be allowed to run under the AD7328 to avoid
noise coupling. The power supply lines to the AD7328 device
should use as large a trace as possible to provide low impedance
paths and reduce the effects of glitches on the power supply line.
V+
DIN
VSS
1ADDITIONAL
V–
PINS OMITTED FOR CLARITY.
04852-056
APPLICATIONS INFORMATION
Figure 56. Schottky Diode Connection
In an application where nonsymmetrical VDD and VSS supplies
are used, adhere to the guidelines provided in Table 16, which
outlines the VSS supply range that can be used for various VDD
voltages when nonsymmetrical supplies are required. When
operating the AD7328 with low VDD and VSS voltages, it is
recommended that these supplies be symmetrical.
Table 16. Nonsymmetrical VDD and VSS Requirements
VDD
5V
6V
7V
8V
9V
10 V to 16.5 V
Typical VSS Range
−5 V to −5.5 V
−5 V to −8.5 V
−5 V to −11.5 V
−5 V to −15 V
−5 V to −16.5 V
−5 V to −16.5 V
For the 0 V to 4 × VREF range, VSS can be tied to AGND as per
the minimum supply recommendations outlined in Table 6.
Rev. C | Page 33 of 36
AD7328
Data Sheet
OUTLINE DIMENSIONS
6.60
6.50
6.40
20
11
4.50
4.40
4.30
6.40 BSC
1
10
PIN 1
0.65
BSC
1.20 MAX
0.15
0.05
COPLANARITY
0.10
0.30
0.19
0.20
0.09
8°
0°
SEATING
PLANE
0.75
0.60
0.45
COMPLIANT TO JEDEC STANDARDS MO-153-AC
Figure 57. 20-Lead Thin Shrink Small Outline Package [TSSOP]
(RU-20)
Dimensions shown in millimeters
ORDERING GUIDE
Model 1
AD7328BRUZ
AD7328BRUZ-REEL
AD7328BRUZ-REEL7
EVAL-AD7328SDZ
EVAL-SDP-CB1Z
1
Temperature Range
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
Package Description
20-Lead TSSOP
20-Lead TSSOP
20-Lead TSSOP
Evaluation Board
Controller Board
Z = RoHS Compliant Part.
Rev. C | Page 34 of 36
Package Option
RU-20
RU-20
RU-20
Data Sheet
AD7328
NOTES
Rev. C | Page 35 of 36
AD7328
Data Sheet
NOTES
©2005–2014 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D04852-0-1/14(C)
Rev. C | Page 36 of 36
Similar pages