AD AD8353ACPZ-REEL7 1 mhz to 2.7 ghz rf gain block Datasheet

1 MHz to 2.7 GHz
RF Gain Block
AD8353
Fixed gain of 20 dB
Operational frequency of 1 MHz to 2.7 GHz
Linear output power up to 9 dBm
Input/output internally matched to 50 Ω
Temperature and power supply stable
Noise figure: 5.3 dB
Power supply: 3 V or 5 V
APPLICATIONS
FUNCTIONAL BLOCK DIAGRAM
BIAS AND VREF
RFIN
COM1
VPOS
RFOUT
AD8353
COM2
02721-001
FEATURES
Figure 1.
VCO buffers
General Tx/Rx amplification
Power amplifier predrivers
Low power antenna drivers
GENERAL DESCRIPTION
The AD8353 is a broadband, fixed-gain, linear amplifier that
operates at frequencies from 1 MHz up to 2.7 GHz. It is
intended for use in a wide variety of wireless devices, including
cellular, broadband, CATV, and LMDS/MMDS applications.
By taking advantage of ADI’s high performance, complementary Si
bipolar process, these gain blocks provide excellent stability
over process, temperature, and power supply. This amplifier is
single-ended and internally matched to 50 Ω with a return loss
of greater than 10 dB over the full operating frequency range.
The AD8353 provides linear output power of 9 dBm with 20 dB
of gain at 900 MHz when biased at 3 V and an external RF
choke is connected between the power supply and the output
pin. The dc supply current is 42 mA. At 900 MHz, the output
third-order intercept (OIP3) is greater than 23 dBm and is
19 dBm at 2.7 GHz.
The noise figure is 5.3 dB at 900 MHz. The reverse isolation
(S12) is −36 dB at 900 MHz and −30 dB at 2.7 GHz.
The AD8353 can also operate with a 5 V power supply; in
which case, no external inductor is required. Under these
conditions, the AD8353 delivers 8 dBm with 20 dB of gain at
900 MHz. The dc supply current is 42 mA. At 900 MHz, the
OIP3 is greater than 22 dBm and is 19 dBm at 2.7 GHz. The noise
figure is 5.6 dB at 900 MHz. The reverse isolation (S12) is −35 dB.
The AD8353 is fabricated on ADI’s proprietary, high performance,
25 GHz, Si complementary, bipolar IC process. The AD8353 is
available in a chip scale package that uses an exposed paddle for
excellent thermal impedance and low impedance electrical
connection to ground. It operates over a −40°C to +85°C
temperature range, and an evaluation board is also available.
Rev. B
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
© 2005 Analog Devices, Inc. All rights reserved.
AD8353
TABLE OF CONTENTS
Features .............................................................................................. 1
Typical Performance Characteristics ..............................................7
Applications....................................................................................... 1
Theory of Operation ...................................................................... 13
Functional Block Diagram .............................................................. 1
Basic Connections...................................................................... 13
General Description ......................................................................... 1
Applications..................................................................................... 14
Revision History ............................................................................... 2
Low Frequency Applications Below 100 MHz........................... 14
Specifications..................................................................................... 3
Evaluation Board ............................................................................ 15
Absolute Maximum Ratings............................................................ 5
Outline Dimensions ....................................................................... 16
ESD Caution.................................................................................. 5
Ordering Guide .......................................................................... 16
Pin Configuration and Function Descriptions............................. 6
REVISION HISTORY
12/05—Rev. A to Rev. B
Changes to Table 1............................................................................ 3
Changes to Table 2............................................................................ 4
Changes to Figure 16........................................................................ 9
Changes to Figure 32...................................................................... 11
Moved Figure 39 to Page 15; Renumbered Sequentially ........... 15
Changes to Ordering Guide .......................................................... 16
8/05—Rev. 0 to Rev. A
Updated Format..................................................................Universal
Changes to Product Title ................................................................. 1
Changes to Features, Figure 1, and General Description............ 1
Changes to Table 1............................................................................ 3
Changes to Table 2............................................................................ 4
Changes to Figure 2 and Table 4..................................................... 6
Changes to Figure 3 caption and Figure 6 caption....................... 7
Changes to Figure 17 caption and Figure 20 caption .................. 9
Changes to Basic Connections Section........................................ 13
Added Low Frequency Applications Below 100 MHz Section. 14
Changes to Table 5.......................................................................... 15
Changes to Ordering Guide .......................................................... 16
Updated Outline Dimensions ....................................................... 16
2/02—Revision 0: Initial Version
Rev. B | Page 2 of 16
AD8353
SPECIFICATIONS
VS = 3 V, TA = 25°C, 100 nH external inductor between RFOUT and VPOS, ZO = 50 Ω, unless otherwise noted.
Table 1.
Parameter
OVERALL FUNCTION
Frequency Range
Gain
Delta Gain
Gain Supply Sensitivity
Reverse Isolation (S12)
RF INPUT INTERFACE
Input Return Loss
RF OUTPUT INTERFACE
Output Compression Point
Delta Compression Point
Output Return Loss
DISTORTION/NOISE
Output Third-Order Intercept
Output Second-Order Intercept
Noise Figure
POWER INTERFACE
Supply Voltage
Total Supply Current
Supply Voltage Sensitivity
Temperature Sensitivity
Conditions
Min
Typ
1
Max
Unit
2700
f = 900 MHz
f = 1.9 GHz
f = 2.7 GHz
f = 900 MHz, −40°C ≤ TA ≤ +85°C
f = 1.9 GHz, −40°C ≤ TA ≤ +85°C
f = 2.7 GHz, −40°C ≤ TA ≤ +85°C
VPOS ± 10%, f = 900 MHz
f = 1.9 GHz
f = 2.7 GHz
f = 900 MHz
f = 1.9 GHz
f = 2.7 GHz
Pin RFIN
f = 900 MHz
f = 1.9 GHz
f = 2.7 GHz
Pin RFOUT
f = 900 MHz, 1 dB compression
f = 1.9 GHz
f = 2.7 GHz
f = 900 MHz, −40°C ≤ TA ≤ +85°C
f = 1.9 GHz, −40°C ≤ TA ≤ +85°C
f = 2.7 GHz, −40°C ≤ TA ≤ +85°C
f = 900 MHz
f = 1.9 GHz
f = 2.7 GHz
19.8
17.7
15.6
−0.97
−1.15
−1.34
0.04
−0.004
−0.04
−35.6
−34.9
−30.3
MHz
dB
dB
dB
dB
dB
dB
dB/V
dB/V
dB/V
dB
dB
dB
22.3
20.9
11.2
dB
dB
dB
9.1
8.4
7.6
−1.46
−1.17
−1
26.3
16.9
13.3
dBm
dBm
dBm
dB
dB
dB
dB
dB
dB
f = 900 MHz, ∆f = 1 MHz, PIN = −28 dBm
f = 1.9 GHz, ∆f = 1 MHz, PIN = −28 dBm
f = 2.7 GHz, ∆f = 1 MHz, PIN = −28 dBm
f = 900 MHz, ∆f = 1 MHz, PIN = −28 dBm
f = 900 MHz
f = 1.9 GHz
f = 2.7 GHz
Pin VPOS
23.6
20.8
19.5
31.6
5.3
6
6.8
dBm
dBm
dBm
dBm
dB
dB
dB
2.7
35
−40°C ≤ TA ≤ +85°C
Rev. B | Page 3 of 16
3
41
15.3
60
3.3
48
V
mA
mA/V
μA/°C
AD8353
VS = 5 V, TA = 25°C, no external inductor between RFOUT and VPOS, ZO = 50 Ω, unless otherwise noted.
Table 2.
Parameter
OVERALL FUNCTION
Frequency Range
Gain
Delta Gain
Gain Supply Sensitivity
Reverse Isolation (S12)
RF INPUT INTERFACE
Input Return Loss
RF OUTPUT INTERFACE
Output Compression Point
Delta Compression Point
Output Return Loss
DISTORTION/NOISE
Output Third-Order Intercept
Output Second-Order Intercept
Noise Figure
POWER INTERFACE
Supply Voltage
Total Supply Current
Supply Voltage Sensitivity
Temperature Sensitivity
Conditions
Min
Typ
Max
Unit
2700
19.5
17.6
15.7
−0.96
−1.18
−1.38
0.09
−0.01
−0.09
−35.4
−34.6
−30.2
MHz
dB
dB
dB
dB
dB
dB
dB/V
dB/V
dB/V
dB
dB
dB
22.9
21.7
11.5
dB
dB
dB
8.3
8.1
7.5
−1.05
−1.49
−1.33
27
22
14.3
dBm
dBm
dBm
dB
dB
dB
dB
dB
dB
22.8
20.6
19.5
30.3
5.6
6.3
7.1
dBm
dBm
dBm
dBm
dB
dB
dB
1
f = 900 MHz
f = 1.9 GHz
f = 2.7 GHz
f = 900 MHz, −40°C ≤ TA ≤ +85°C
f = 1.9 GHz, −40°C ≤ TA ≤ +85°C
f = 2.7 GHz, −40°C ≤ TA ≤ +85°C
VPOS ± 10%, f = 900 MHz
f = 1.9 GHz
f = 2.7 GHz
f = 900 MHz
f = 1.9 GHz
f = 2.7 GHz
Pin RFIN
f = 900 MHz
f = 1.9 GHz
f = 2.7 GHz
Pin RFOUT
f = 900 MHz
f = 1.9 GHz
f = 2.7 GHz
f = 900 MHz, −40°C ≤ TA ≤ +85°C
f = 1.9 GHz, −40°C ≤ TA ≤ +85°C
f = 2.7 GHz, −40°C ≤ TA ≤ +85°C
f = 900 MHz
f = 1.9 GHz
f = 2.7 GHz
f = 900 MHz, ∆f = 1 MHz, PIN = −28 dBm
f = 1.9 GHz, ∆f = 1 MHz, PIN = −28 dBm
f = 2.7 GHz, ∆f = 1 MHz, PIN = −28 dBm
f = 900 MHz, ∆f = 1 MHz, PIN = −28 dBm
f = 900 MHz
f = 1.9 GHz
f = 2.7 GHz
Pin VPOS
4.5
35
−40°C ≤ TA ≤ +85°C
Rev. B | Page 4 of 16
5
42
4.3
45.7
5.5
52
V
mA
mA/V
μA/°C
AD8353
ABSOLUTE MAXIMUM RATINGS
Table 3.
Parameter
Supply Voltage, VPOS
Input Power (re: 50 Ω)
Equivalent Voltage
Internal Power Dissipation
Paddle Not Soldered
Paddle Soldered
θJA (Paddle Soldered)
θJA (Paddle Not Soldered)
Maximum Junction Temperature
Operating Temperature Range
Storage Temperature Range
Lead Temperature (Soldering 60 sec)
Rating
5.5 V
10 dBm
700 mV rms
325 mW
812 mW
80°C/W
200°C/W
150°C
−40°C to +85°C
−65°C to +150°C
240°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. B | Page 5 of 16
AD8353
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
COM1 1
NC 2
8 COM1
AD8353
NC = NO CONNECT
04862-002
7 RFOUT
TOP VIEW
RFIN 3 (Not to Scale) 6 VPOS
5 COM2
COM2 4
Figure 2. Pin Configuration
Table 4. Pin Function Descriptions
Pin No.
1, 8
2
3
4, 5
6
7
Mnemonic
COM1
NC
RFIN
COM2
VPOS
RFOUT
Description
Device Common. Connect to low impedance ground.
No Connection.
RF Input Connection. Must be ac-coupled.
Device Common. Connect to low impedance ground.
Positive Supply Voltage.
RF Output Connection. Must be ac-coupled.
Rev. B | Page 6 of 16
AD8353
TYPICAL PERFORMANCE CHARACTERISTICS
90
90
120
120
60
150
150
30
210
330
30
180
60
330
02721-003
210
300
240
270
300
240
270
Figure 3. S11 vs. Frequency, VS = 3 V, TA = 25°C, dc ≤ f ≤ 3 GHz
Figure 6. S22 vs. Frequency, VS = 3 V, TA = 25°C, dc ≤ f ≤ 3 GHz
25
25
GAIN AT –40°C
20
20
15
15
GAIN (dB)
GAIN AT 2.7V
10
GAIN AT 3.0V
GAIN AT +25°C
GAIN AT +85°C
10
0
1000
1500
2000
2500
3000
FREQUENCY (MHz)
0
02721-004
500
0
0
1000
1500
2000
2500
3000
FREQUENCY (MHz)
Figure 7. Gain vs. Frequency, VS = 3 V, TA = −40°C, +25°C, and +85°C
Figure 4. Gain vs. Frequency, VS = 2.7 V, 3 V, and 3.3 V, TA = 25°C
0
–5
–5
REVERSE ISOLATION (dB)
0
–10
–15
–20
–25
S12 AT 3.0V S AT 2.7V
12
–30
500
02721-007
5
5
–10
–15
–20
S12 AT +25°C
–25
S12 AT –40°C
–30
–35
–35
S12 AT 3.3V
0
500
S12 AT +85°C
–40
1000
1500
FREQUENCY (MHz)
2000
2500
3000
0
02721-005
–40
Figure 5. Reverse Isolation vs. Frequency, VS = 2.7 V, 3 V, and 3.3 V, TA = 25°C
500
1000
1500
FREQUENCY (MHz)
2000
2500
3000
02721-008
GAIN (dB)
GAIN AT 3.3V
REVERSE ISOLATION (dB)
02721-006
180
Figure 8. Reverse Isolation vs. Frequency, VS = 3 V, TA = −40°C, +25°C, and +85°C
Rev. B | Page 7 of 16
AD8353
12
12
10
10
P1dB AT –40°C
P1dB AT 3.3V
4
4
2
2
0
0
500
1000
1500
2000
2500
3000
FREQUENCY (MHz)
0
P1dB AT +85°C
P1dB AT +25°C
6
0
500
1000
1500
2000
2500
3000
FREQUENCY (MHz)
Figure 9. P1dB vs. Frequency, VS = 2.7 V, 3 V, and 3.3 V, TA = 25°C
02721-012
P1dB AT 2.7V
P1dB AT 3.0V
6
P1dB (dBm)
8
02721-009
P1dB (dBm)
8
Figure 12. P1dB vs. Frequency, VS = 3 V, TA = −40°C, +25°C, and +85°C
45
30
40
25
30
PERCENTAGE (%)
PERCENTAGE (%)
35
25
20
15
20
15
10
10
5
7.2
7.4
7.6
7.8
8.0
8.2
8.4
8.6
8.8
OUTPUT 1dB COMPRESSION POINT (dBm)
9.0
0
19.1
28
28
26
26
24
24
OIP3 (dBm)
OIP3 AT 3.0V
OIP3 AT 2.7V
21.1
21.5
21.9
OIP3 AT –40°C
20
OIP3 AT +85°C
OIP3 AT +25°C
18
16
16
14
14
0
500
1000
1500
2000
2500
3000
FREQUENCY (MHz)
10
Figure 11. OIP3 vs. Frequency, VS = 2.7 V, 3 V, and 3.3 V, TA = 25°C
0
500
1000
1500
2000
2500
3000
FREQUENCY (MHz)
Figure 14. OIP3 vs. Frequency, VS = 3 V, TA = −40°C, +25°C, and +85°C
Rev. B | Page 8 of 16
02721-014
12
12
02721-011
OIP3 (dBm)
20
10
20.3
20.7
OIP3 (dBm)
22
OIP3 AT 3.3V
18
19.9
Figure 13. Distribution of OIP3, VS = 3 V, TA = 25°C, f = 2.2 GHz
Figure 10. Distribution of P1dB, VS = 3 V, TA = 25°C, f = 2.2 GHz
22
19.5
02721-013
0
7.0
02721-010
5
AD8353
8.0
8.5
7.5
8.0
7.5
NOISE FIGURE (dB)
6.5
NF AT 3.3V
6.0
5.5
5.0
NF AT 2.7V
7.0
NF AT +85°C
6.5
6.0
NF AT +25°C
5.5
NF AT Ð
–40°C
5.0
NF AT 3.0V
4.5
02721-015
4.5
4.0
0
500
1000
1500
2000
FREQUENCY (MHz)
2500
3000
Figure 15. Noise Figure vs. Frequency, VS = 2.7 V, 3 V, and 3.3 V, TA = 25°C
4.0
0
500
1000
1500
2000
FREQUENCY (MHz)
2500
3000
02721-018
NOISE FIGURE (dBm)
7.0
Figure 18. Noise Figure vs. Frequency, VS = 3 V, TA = −40°C, +25°C, and +85°C
35
50
IS AT 3.3V
45
30
SUPPLY CURRENT (mA)
40
PERCENTAGE (%)
25
20
15
10
IS AT 3.0V
35
IS AT 2.7V
30
25
20
15
10
5
0
–60
–40
–20
60
80
100
Figure 19. Supply Current vs. Temperature, VS = 2.7 V, 3 V, and 3.3 V
Figure 16. Distribution of Noise Figure, VS = 3 V, TA = 25°C, f = 2.2 GHz
90
90
120
20
0
40
TEMPERATURE (°C)
02721-019
02721-016
5
0
5.90 5.95 6.00 6.05 6.10 6.15 6.20 6.25 6.30 6.35 6.40 6.45 6.50 6.55 6.60
NOISE FIGURE (dB)
120
60
150
150
30
180
30
180
0
330
0
330
210
300
240
300
240
270
270
Figure 20. S22 vs. Frequency, VS = 5 V, TA = 25°C, dc ≤ f ≤ 3 GHz
Figure 17. S11 vs. Frequency, VS = 5 V, TA = 25°C, dc ≤ f ≤ 3 GHz
Rev. B | Page 9 of 16
02721-020
02721-017
210
60
AD8353
25
25
GAIN AT 5.5V
GAIN AT –40°C
20
20
15
GAIN (dB)
GAIN AT 5.0V
GAIN AT 4.5V
10
15
GAIN AT +25°C
10
5
5
500
1000
1500
2000
2500
3000
0
FREQUENCY (MHz)
0
0
–5
–5
REVERSE ISOLATION (dB)
2000
–10
–15
–20
S12 AT 5V
S12 AT 5.5V
3000
–10
–15
–20
S12 AT +25°C
–25
–30
S12 AT +85°C
–35
–35
S12 AT 4.5V
0
500
1000
1500
2000
FREQUENCY (MHz)
2500
3000
02721-022
S12 AT –40°C
–40
Figure 22. Reverse Isolation vs. Frequency, VS = 4.5 V, 5 V, and 5.5 V, TA = 25°C
–40
0
500
1000
1500
2000
FREQUENCY (MHz)
2500
3000
Figure 25. Reverse Isolation vs. Frequency, VS = 5 V, TA = −40°C, +25°C, and +85°C
10
12
P1dB AT 5.5V
9
P1dB AT +85°C
10
P1dB AT +25°C
8
7
8
6
P1dB (dBm)
P1dB AT 4.5V
P1dB AT 5.0V
5
4
P1dB AT –40°C
6
4
3
2
2
1
0
0
500
1000
1500
2000
FREQUENCY (MHz)
2500
3000
02721-023
P1dB (dBm)
2500
02721-025
REVERSE ISOLATION (dB)
1500
Figure 24. Gain vs. Frequency, VS = 5 V, TA = −40°C, +25°C, and +85°C
0
–30
1000
FREQUENCY (MHz)
Figure 21. Gain vs. Frequency, VS = 4.5 V, 5 V, and 5.5 V, TA = 25°C
–25
500
02721-024
0
02721-021
0
0
0
500
1000
1500
2000
2500
3000
FREQUENCY (MHz)
Figure 26. P1dB vs. Frequency, VS = 5 V, TA = –40°C, +25°C, and +85°C
Figure 23. P1dB vs. Frequency, VS = 4.5 V, 5 V, and 5.5 V, TA = 25°C
Rev. B | Page 10 of 16
02721-026
GAIN (dB)
GAIN AT +85°C
AD8353
30
45
40
25
PERCENTAGE (%)
PERCENTAGE (%)
35
30
25
20
15
20
15
10
10
5
7.4
7.6
7.8
8.0
8.2
8.4
8.6
OUTPUT 1dB COMPRESSION POINT (dBm)
8.8
0
18.8
26
26
24
24
OIP3 (dBm)
18
OIP3 AT 4.5V
16
12
10
2500
3000
OIP3 AT +25°C
OIP3 AT +85°C
16
12
1000
1500
2000
FREQUENCY (MHz)
21.6
OIP3 AT –40°C
18
14
500
21.2
20
14
02721-028
OIP3 (dBm)
20
0
20.8
22
OIP3 AT 5.5V
OIP3 AT 5.0V
20.0
20.4
OIP3 (dBm)
19.6
Figure 30. Distribution of OIP3, VS = 5 V, TA = 25°C, f = 2.2 GHz
Figure 27. Distribution of P1dB, VS = 3 V, TA = 25°C, f = 2.2 GHz
22
19.2
02721-030
7.2
10
0
Figure 28. OIP3 vs. Frequency, VS = 4.5 V, 5 V, and 5.5 V, TA = 27°C
500
1000
1500
2000
FREQUENCY (MHz)
2500
3000
02721-031
0
7.0
02721-027
5
Figure 31. OIP3 vs. Frequency, VS = 5 V, TA = –40°C, +25°C, and +85°C
9.0
10
8.5
9
NOISE FIGURE (dBm)
7.5
7.0
NF AT 5.5V
6.5
6.0
NF AT 4.5V
5.5
8
7
NF AT +85°C
6
NF AT +25°C
5.0
5
NF AT 5.0V
4.5
4.0
0
500
1000
1500
2000
FREQUENCY (MHz)
2500
3000
Figure 29. Noise Figure vs. Frequency, VS = 4.5 V, 5 V, and 5.5 V, TA = 25°C
4
0
500
1000
1500
2000
FREQUENCY (MHz)
2500
3000
02721-032
NF AT –40°C
02721-029
NOISE FIGURE (dB)
8.0
Figure 32. Noise Figure vs. Frequency, VS = 5 V, TA = –40°C, +25°C, and +85°C
Rev. B | Page 11 of 16
25
10
19
20
5
18
0
17
10
–5
16
5
–10
15
15
0
6.10 6.15 6.20 6.25 6.30 6.35 6.40 6.45 6.50 6.55 6.60 6.65 6.70
NOISE FIGURE (dB)
Figure 33. Distribution of Noise Figure, VS = 5 V, TA = 25°C, f = 2.2 GHz
–30
–25
–20
–15
–10
PIN (dBm)
–5
0
5
Figure 35. Output Power and Gain vs. Input Power, VS = 3 V, TA = 25°C, f = 900 MHz
15
20
10
19
5
18
0
17
–5
16
–10
15
IS AT 5.5V
40
35
POUT (dBm)
IS AT 5.0V
30
25
20
GAIN (dB)
IS AT 4.5V
10
5
0
–60
–40
–20
20
0
40
TEMPERATURE (°C)
60
80
–15
–30
100
Figure 34. Supply Current vs. Temperature, VS = 4.5 V, 5 V, and 5.5 V
14
–25
–20
–15
–10
PIN (dBm)
–5
0
5
02721-036
15
02721-034
SUPPLY CURRENT (mA)
14
–15
50
45
GAIN (dB)
20
02721-035
15
POUT (dBm)
30
02721-033
PERCENTAGE (%)
AD8353
Figure 36. Output Power and Gain vs. Input Power, VS = 5 V, TA = 25°C, f = 900 MHz
Rev. B | Page 12 of 16
AD8353
THEORY OF OPERATION
The AD8353 is a 2-stage, feedback amplifier employing both
shunt-series and shunt-shunt feedback. The first stage is
degenerated and resistively loaded and provides approximately
10 dB of gain. The second stage is a PNP-NPN Darlington
output stage, which provides another 10 dB of gain. Seriesshunt feedback from the emitter of the output transistor sets the
input impedance to 50 Ω over a broad frequency range. Shuntshunt feedback from the amplifier output to the input of the
Darlington stage helps to set the output impedance to 50 Ω. The
amplifier can be operated from a 3 V supply by adding a choke
inductor from the amplifier output to VPOS. Without this
choke inductor, operation from a 5 V supply is also possible.
It is critical to supply very low inductance ground connections
to the ground pins (Pin 1, Pin 4, Pin 5, and Pin 8) as well as to
the backside exposed paddle. This ensures stable operation.
BASIC CONNECTIONS
The AD8353 RF gain block is a fixed gain amplifier with
single-ended input and output ports whose impedances are
nominally equal to 50 Ω over the frequency range 1 MHz to
2.7 GHz. Consequently, it can be directly inserted into a 50 Ω
system with no impedance matching circuitry required.
The input and output impedances are sufficiently stable vs.
variations in temperature and supply voltage that no impedance
matching compensation is required. A complete set of
scattering parameters is available at www.analog.com.
When the supply voltage is 3 V, it is recommended that an
external RF choke be connected between the supply voltage
and the output pin, RFOUT. This increases the dc voltage
applied to the collector of the output amplifier stage, which
improves performance of the AD8353 to be very similar to the
performance produced when 5 V is used for the supply voltage.
The inductance of the RF choke should be approximately
100 nH, and care should be taken to ensure that the lowest
series self-resonant frequency of this choke is well above the
maximum frequency of operation for the AD8353. For lower
frequency operation, use a higher value inductor.
The input pin (RFIN) is connected directly to the base of the first
amplifier stage, which is internally biased to approximately 1 V;
therefore, a dc blocking capacitor should be connected between the
source that drives the AD8353 and the input pin, RFIN.
Bypass the supply voltage input, VPOS, using a large value
capacitance (approximately 0.47 μF or larger) and a smaller,
high frequency bypass capacitor (approximately 100 pF)
physically located close to the VPOS pin.
The AD8353 is designed to operate over a wide supply voltage
range, from 2.7 V to 5.5 V. The output of the part, RFOUT, is
taken directly from the collector of the output amplifier stage.
This node is internally biased to approximately 2.2 V when the
supply voltage is 5 V. Consequently, a dc blocking capacitor
should be connected between the output pin, RFOUT, and the
load that it drives. The value of this capacitor is not critical, but
it should be 100 pF or larger.
The recommended connections and components are shown in
Figure 40.
Rev. B | Page 13 of 16
AD8353
APPLICATIONS
The AD8353 RF gain block can be used as a general-purpose,
fixed gain amplifier in a wide variety of applications, such as a
driver for a transmitter power amplifier (see Figure 37). Its
excellent reverse isolation also makes this amplifier suitable for
use as a local oscillator buffer amplifier that would drive the
local oscillator port of an upconverter or downconverter mixer
(see Figure 38).
LOW FREQUENCY APPLICATIONS BELOW 100 MHz
The AD8353 RF gain block can be used below 100 MHz. To
accomplish this, the series dc blocking capacitors, C1 and C2,
need to be changed to a higher value that is appropriate for the
desired frequency. C1 and C2 were changed to 0.1 μF to
accomplish the sweep in Figure 39.
21.0
dB-S21
AD8353
HIGH POWER
AMPLIFIER
02721-037
20.5
Figure 37. AD8353 as a Driver Amplifier
20.0
19.5
19.0
18.5
MIXER
18.0
17.5
AD8353
02721-042
04862-038
LOCAL OSCILLATOR
17.0
16.5
16.0
Figure 38. AD8353 as a LO Driver Amplifier
CH 1: START 300.000kHz
STOP 100.000MHz
Figure 39. Low Frequency Application from
300 kHz to 100 MHz at 5 V VPOS, −12 dBm Input Power
Rev. B | Page 14 of 16
AD8353
EVALUATION BOARD
Figure 40 shows the schematic of the AD8353 evaluation board.
Note that L1 is shown as an optional component that is used to
obtain maximum gain only when VP = 3 V. The board is powered
by a single supply in the 2.7 V to 5.5 V range. The power supply
is decoupled by a 0.47 μF and a 100 pF capacitor.
AD8353
1
2
NC
COM1 8
C2
1000pF
OUTPUT
C3
100pF
C4
0.47μF
RFOUT 7
C1
1000pF
L1
4
RFIN
COM2
VPOS 6
COM2 5
NC = NO CONNECT
04862-040
3
02721-039
INPUT
COM1
Figure 41. Silkscreen Top
Figure 40. Evaluation Board Schematic
Table 5. Evaluation Board Configuration Options
Function
AC coupling capacitors.
C3
High frequency bypass capacitor.
C4
Low frequency bypass capacitor.
L1
Optional RF choke, used to increase
current through output stage when
VP = 3 V. Not recommended for use
when VP = 5 V.
Default
Value
1000 pF,
0603
100 pF
0603
0.47 μF,
0603
100 nH,
0603
04862-041
Component
C1, C2
Figure 42. Component Side
Rev. B | Page 15 of 16
AD8353
OUTLINE DIMENSIONS
1.89
1.74
1.59
3.25
3.00
2.75
1.95
1.75
1.55
TOP VIEW
12° MAX
SEATING
PLANE
5 BOTTOM VIEW
* 8
EXPOSED PAD
4
2.95
2.75
2.55
PIN 1
INDICATOR
1.00
0.85
0.80
0.60
0.45
0.30
2.25
2.00
1.75
0.55
0.40
0.30
0.50 BSC
0.15
0.10
0.05
1
0.25
0.20
0.15
0.80 MAX
0.65 TYP
0.05 MAX
0.02 NOM
0.30
0.23
0.18
0.20 REF
Figure 43. 8-Lead Lead Frame Chip Scale Package [LFCSP_VD]
2 mm × 3 mm Body, Very Thin, Dual Lead
CP-8-1
Dimensions shown in millimeters
ORDERING GUIDE
Model
AD8353ACP-R2
AD8353ACP-REEL7
AD8353ACPZ-REEL7 1
AD8353-EVAL
1
Temperature Range
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
Package Description
8-Lead LFCSP_VD
8-Lead LFCSP_VD, 7" Tape and Reel
8-Lead LFCSP_VD, 7" Tape and Reel
Evaluation Board
Package Option
CP-8-1
CP-8-1
CP-8-1
Branding
JB
JB
0E
Z = Pb-free part.
© 2005 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
C02721–0–12/05(B)
T
T
Rev. B | Page 16 of 16