AH3382 HIGH VOLTAGE ULTRA HIGH SENSITIVITY HALL EFFECT LATCH WITH INTERNAL PULL-UP RESISTOR Description Pin Assignments The AH3382 is a high voltage ultra high sensitivity Hall Effect Unipolar switch IC designed for proximity, position and level sensing (TOP View) in industrial and consumer home appliances and personal care applications. To support wide range of demanding applications, the 3 OUTPUT design has been optimized to operate over the supply range of 3.0V GND 2 NEW PRODUCT to 28V. With chopper stabilized architecture and an internal bandgap 1 VDD regulator to provide temperature compensated supply for internal circuits, the AH3382 provides a reliable solution over the whole SC59 and SOT23 operating range. For robustness and protection, the device has a reverse blocking diode with a Zener clamp on the supply. The output has an over current limit and a Zener clamp. The internally pulled-up output can be switched on with South pole of sufficient strength. When the magnetic flux density (B) perpendicular (TOP View) to the package is larger than the operate point (BOP) the output is switched on (pulled low) and is held on until magnetic flux density B is 3. OUTPUT lower than the release point (BRP). The output remains switched off for 2. GND North pole fields to or no magnetic fields. 1. VDD SIP-3 (Bulk Pack) The magnetic operating and release polarity is opposite for SOT23 and SC59 packages. The SOT23 and SIP-3 (Ammo Pack), SIP-3 (Bulk Pack) packages will require south pole to the part marking side to operate while SC59 will require south pole to the non-part marking side. Features Applications • Unipolar Operation • Position and Proximity Sensing in Industrial Applications High Sensitivity: BOP and BRP of +55G and +35G Typical • Applications • Internally Pull-up Resistor on the Output with Over Current Limit • Open and Close Detect • 3.0V to 28V Operating Voltage Range • Position Detect Chopper Stabilized Design Provides • Level Detect o Superior Temperature Stability • Flow Meters o Minimal Switch Point Drift • Contact-less Switches o Enhanced Immunity to Stress • • • Good RF Noise Immunity • Reverse Blocking Diode • Zener Clamp on Supply and Output Pins • -40C to +125C Operating Temperature • ESD: HBM ＞ 6kV • Industry Standard SC59, SOT23 and SIP-3 (Ammo Pack), SIP-3 (Bulk Pack) Packages Totally Lead-Free & Fully RoHS Compliant (Notes 1 & 2) Halogen and Antimony Free. “Green” Device (Note 3) Notes: 1. No purposely added lead. Fully EU Directive 2002/95/EC (RoHS) & 2011/65/EU (RoHS 2) compliant. 2. See http://www.diodes.com for more information about Diodes Incorporated’s definitions of Halogen- and Antimony-free, "Green" and Lead-free. 3. Halogen- and Antimony-free "Green” products are defined as those which contain <900ppm bromine, <900ppm chlorine (<1500ppm total Br + Cl) and <1000ppm antimony compounds. AH3382 Document number: DS38921 Rev. 1 - 2 1 of 14 www.diodes.com July 2016 © Diodes Incorporated AH3382 Typical Applications Circuit NEW PRODUCT 3.0V to 28V VDD OUTPUT AH3382 CIN GND Note: 4. CIN is for power stabilization and to strengthen the noise immunity, the recommended capacitance is 10nF ~ 100nF. Pin Descriptions Package: SC59, SOT23 and SIP-3 (Ammo Pack), SIP-3 (Bulk Pack) Pin Number Pin Name 1 VDD 2 3 GND OUTPUT Function Power Supply Input Ground Output Pin Functional Block Diagram VDD Power switch To All Subcircuits Amp Low-Pass Filter Sample and Hold Dynamic Offset Cancellation Amp OUTPUT Control Current Limit GND AH3382 Document number: DS38921 Rev. 1 - 2 2 of 14 www.diodes.com July 2016 © Diodes Incorporated AH3382 Absolute Maximum Ratings (Note 5 & 6) (@TA = +25°C, unless otherwise specified.) Symbol VDD VDDR VOUT_MAX IOUT IOUT_R NEW PRODUCT B Characteristic Supply Voltage (Note 6) Reverse Supply Voltage (Note 6) Output Off Voltage (Note 6) Continuous Output Current Reverse Output Current Magnetic Flux Density PD Storage Temperature Range TJ Maximum Junction Temperature ESD HBM Notes: Unit V V V mA -50 mA Unlimited SIP-3 (Ammo Pack), SIP-3 (Bulk Pack) SC59 and SOT23 Package Power Dissipation Ts Value 32 -32 32 60 550 mW 230 -65 to +165 C +150 C kV Electros Static Discharge Withstand - Human Body Model (HMB) 6 5. Stresses greater than the 'Absolute Maximum Ratings' specified above may cause permanent damage to the device. These are stress ratings only; functional operation of the device at these or any other conditions exceeding those indicated in this specification is not implied. Device reliability may be affected by exposure to absolute maximum rating conditions for extended periods of time. 6. The absolute maximum VDD of 32V is a transient stress rating and is not meant as a functional operating condition. It is not recommended to operate the device at the absolute maximum rated conditions for any period of time. Recommended Operating Conditions (@TA = -40°C to +125°C, unless otherwise specified.) Symbol VDD TA Parameter Supply Voltage Operating Condition Rating 3.0 to 28 Unit V Operating Temperature Range Operating -40 to +125 C Electrical Characteristics (Note 7 & 8) (@TA = -40°C to +125°C, VDD = 3V to 28V, unless otherwise specified.) Symbol VOUT_ON ILKG IDD Supply Current RPU tST fC Internal pull-up resistance Device start-up time Chopping Frequency Response Time Delay (Time from magnetic threshold reached to the start of the output rise or fall) Output Rising Time (External pull-up resistor RL and load capacitance dependent) Output Falling Time (Internal switch resistance and load capacitance dependent) Output Current Limit Zener Clamp Voltage tD tR tF IOCL VZ Notes: Parameter Output ON Voltage Output Leakage Current (When output is off) Condition IOUT = 20mA, B > BOP Min - Typ 0.2 Max 0.4 Unit V - <0.1 10 µA 10 - 3 14 10 800 3.5 4 18 - mA mA k µs kHz (Note 9) - 3.75 - µs RL = 1kΩ, CL = 20pF - 0.2 1 µs RL = 1kΩ, CL = 20pF - 0.1 1 µs B > BOP, (Note 10 ) IDD = 5mA 30 28 - 55 - mA V VOUT = 28V, B < BRP, Output off Output open, TA = +25C Output open, TA = -40C to +125C TA = -40°C to 125°C, VDD >= 3V, B > BOP (Note 7) - 7. When power is initially turned on, VDD must be within its correct operating range (3.0V to 28V) to guarantee the output sampling. The output state is valid after the start-up time of 10s typical from the operating voltage reaching 3V. 8. Typical values are defined at TA = +25C, VDD = 12V. Maximum and minimum values over the operating temperature range is not tested in production but guaranteed by design, process control and characterization. 9. Guaranteed by design, process control and characterization, Not tested in production. 10. The device will limit the output current IOUT to current limit of IOCL. AH3382 Document number: DS38921 Rev. 1 - 2 3 of 14 www.diodes.com July 2016 © Diodes Incorporated AH3382 Symbol BOPS (South pole to part marking side for SOT23 and SIP-3 (Ammo Pack), SIP-3 (Bulk Pack) packages; South pole to the non-part marking side for SC59 package. See diagram below) BRPS (South pole to part marking side for SOT23 and SIP-3 (Ammo Pack), SIP-3 (Bulk Pack) packages; South pole to the non-part marking side for SC59 package. See diagram below) BHY (|BOPX|-|BRPX|) Notes: Parameter Condition VDD = 12V, TA = +25C Operation Point TA = -40C to +125C VDD = 12V, TA = +25C Release Point TA = -40C to +125C VDD = 12V, TA = +25C TA = -40C to +125C Hysteresis (Note 13) (1mT=10 Gauss) Max Unit Min Typ - 55 - 40 55 70 - 35 - 20 35 50 15 20 20 25 Gauss 11. When power is initially turned on, VDD must be within its correct operating range (3.0V to 28V) to guarantee the output sampling. The output state is valid after the start-up time of 10s typical from the operating voltage reaching 3V. 12. Typical values are defined at TA = +25C, VDD = 12V. Maximum and minimum values over the operating temperature range is not tested in production but guaranteed by design, process control and characterization. 13. Maximum and minimum hysteresis is guaranteed by design, process control and characterization. Output ( Output Voltage ) NEW PRODUCT Magnetic Characteristics (Note 11 &12) (TA = -40°C to +125°C, VDD = 3.0V to 28V, unless otherwise specified.) (Off-state) Turn off VDD BHY Turn on (On-state) VOUT_ON = VSAT 0 BRPS BOPS ( Magnetic Flux Density B ) S S S Part mark Part mark Part mark AH3382 Document number: DS38921 Rev. 1 - 2 N N SC59 SOT23 4 of 14 www.diodes.com N SIP-3(Ammo Pack) SIP-3(Bulk Pack) July 2016 © Diodes Incorporated AH3382 Typical Operating Characteristics NEW PRODUCT Output Switch Operate and Release Points (Magnetic Thresholds) – BOPS and BRPS Supply Current AH3382 Document number: DS38921 Rev. 1 - 2 5 of 14 www.diodes.com July 2016 © Diodes Incorporated AH3382 Typical Operating Characteristics (Cont.) NEW PRODUCT Output Switch On Voltage Output Pull-Up Resistor (Internal) Output Current Limit AH3382 Document number: DS38921 Rev. 1 - 2 6 of 14 www.diodes.com July 2016 © Diodes Incorporated AH3382 Thermal Performance Characteristics (1) Package type: SC59 and SOT23 TA (°C) 25 50 60 70 80 85 90 100 105 110 120 125 130 140 150 PD (mW) 230 184 166 147 129 120 110 92 83 74 55 46 37 18 0 Power Dissipation Curve Power Dissipation PD (mW) NEW PRODUCT 300 200 100 0 -40 0 25 50 75 100 125 150 Ambient Temperature TA (oC) (2) Package type: SIP-3 (Ammo Pack), SIP-3 (Bulk Pack) TA (°C) 25 50 60 70 80 85 90 100 105 110 120 125 130 140 150 PD (mW) 550 440 396 362 308 286 264 220 198 176 132 110 88 44 0 PD (mW) Power Dissipation Curve 600 500 400 300 200 100 0 -40 0 25 50 75 100 125 150 TA (°C) AH3382 Document number: DS38921 Rev. 1 - 2 7 of 14 www.diodes.com July 2016 © Diodes Incorporated AH3382 Ordering Information AH3382 - X - X Package NEW PRODUCT Product Name Packing P : SIP-3(Ammo Pack) P : SIP-3(Bulk Pack) SA : SOT23 W : SC59 7 : Tape & Reel A: Ammo Box (Note 14) B: Bulk (Note 15) 7” Tape and Reel Part Number Quantity Suffix Bulk Part Number Suffix Part Number Package Code Packaging Quantity AH3382-P-A AH3382-P-B P P SIP-3 (Ammo Pack) SIP-3 (Bulk Pack) NA 1000 NA -B NA NA NA NA AH3382-SA-7 SA SOT23 NA NA 3000/Tape & Reel AH3382-W-7 W SC59 NA NA 3000/Tape & Reel Notes: Ammo Box Quantity Part Number Suffix -7 4000/Box NA NA -A NA NA -7 NA NA 14. Ammo Box is for SIP-3 (Ammo Pack) Spread Lead. 15. Bulk is for SIP-3 (Bulk Pack) Straight Lead. Marking Information (1) Package Type: SC59 and SOT23 ( Top View ) XX Y W X Part Number AH3382 AH3382 (2) XX : Identification code Y : Year 0 to 9 W : Week : A to Z : 1 to 26 week; a to z : 27 to 52 week; z represents 52 and 53 week X : Internal code Package SC59 SOT23 Identification Code DU MU Package Type: SIP-3 (Ammo Pack), SIP-3 (Bulk Pack) ( Top View ) Part Number 3382 Y WW X Y : Year : 0~9 WW : Week : 01~52, "52" represents 52 and 53 week X : Internal Code Part Number Package Identification Code AH3382 AH3382 SIP-3 (Ammo Pack) SIP-3 (Bulk Pack) 3382 3382 AH3382 Document number: DS38921 Rev. 1 - 2 8 of 14 www.diodes.com July 2016 © Diodes Incorporated AH3382 Package Outline Dimensions (All dimensions in mm.) Please see http://www.diodes.com/package-outlines.html for the latest version. (1) Package Type: SC59 NEW PRODUCT A SC59 Dim Min Max Typ A 0.35 0.50 0.38 B 1.50 1.70 1.60 C 2.70 3.00 2.80 D 0.95 G 1.90 H 2.90 3.10 3.00 J 0.013 0.10 0.05 K 1.00 1.30 1.10 L 0.35 0.55 0.40 M 0.10 0.20 0.15 N 0.70 0.80 0.75 0° 8° All Dimensions in mm B C G H K J M N L D 0.10/0.20 CL 0.7/0.9 PART MARKING SURFACE 0.595/0.715 Min/Max Die Hall Sensor Pin1 1.3/1.5 Sensor Location AH3382 Document number: DS38921 Rev. 1 - 2 9 of 14 www.diodes.com July 2016 © Diodes Incorporated AH3382 Package Outline Dimensions (Cont.) (All dimensions in mm.) Please see http://www.diodes.com/package-outlines.html for the latest version. (2) Package Type: SOT23 All 7° K1 GAUGE PLANE 0.25 J K a M A L C L1 B D F SOT23 Dim Min Max Typ A 0.37 0.51 0.40 B 1.20 1.40 1.30 C 2.30 2.50 2.40 D 0.89 1.03 0.915 F 0.45 0.60 0.535 G 1.78 2.05 1.83 H 2.80 3.00 2.90 J 0.013 0.10 0.05 K 0.890 1.00 0.975 K1 0.903 1.10 1.025 L 0.45 0.61 0.55 L1 0.25 0.55 0.40 M 0.085 0.150 0.110 a 0° 8° -All Dimensions in mm G 0.17/0.37 Min/Max PART MARKING SURFACE 0.5/0.7 NEW PRODUCT H Die Hall Sensor Pin1 1.4/1.5 Sensor Location – To be updated AH3382 Document number: DS38921 Rev. 1 - 2 10 of 14 www.diodes.com July 2016 © Diodes Incorporated AH3382 Package Outline Dimensions (Cont.) (All dimensions in mm.) Please see http://www.diodes.com/package-outlines.html for the latest version. (3) Package Type: SIP-3 (Bulk Pack) L a1 J a2 B P N D C a3 A E G H F a4 SIP-3 (Bulk Pack) Dim Min Max A 3.9 4.3 a1 5 Typ a2 5 Typ a3 45 Typ a4 3 Typ B 2.8 3.2 C 1.40 1.60 D 0.33 0.432 E 0.40 0.508 F 0 0.2 G 1.24 1.30 H 2.51 2.57 J 0.35 0.43 L 14.0 15.0 N 0.63 0.84 P 1.55 All Dimensions in mm Min/Max 0.63/0.84 0.27/0.48 1.90/2.10 1.05/1.25 PART MARKING SURFACE Hall Sensor 1 2 Die NEW PRODUCT Sensor location to be added PART MARKING SURFACE 3 Sensor Location – To be updated AH3382 Document number: DS38921 Rev. 1 - 2 11 of 14 www.diodes.com July 2016 © Diodes Incorporated AH3382 Package Outline Dimensions (Cont.) (All dimensions in mm.) Please see http://www.diodes.com/package-outlines.html for the latest version. N D EF SIP-3 (Ammo Pack) Dim Min Max A 3.9 4.3 a1 45 Typ a2 3 Typ B 2.8 3.2 C 1.40 1.60 D 0.35 0.41 E 0.43 0.48 F 0 0.2 G 2.4 2.9 N 0.63 0.84 P 1.55 All Dimensions in mm C A G a1 a2 B P Min/Max 0.63/0.84 0.27/0.48 1.90/2.10 1.05/1.25 PART MARKING SURFACE Hall Sensor 1 2 Die NEW PRODUCT (4) Package Type: SIP-3 (Ammo Pack) PART MARKING SURFACE 3 Sensor Location – To be updated AH3382 Document number: DS38921 Rev. 1 - 2 12 of 14 www.diodes.com July 2016 © Diodes Incorporated AH3382 Suggested Pad Layout Please see http://www.diodes.com/package-outlines.html for the latest version. Package Type: SC59 NEW PRODUCT (1) Y Z X (2) Dimensions Value (in mm) Z 3.4 X 0.8 Y 1.0 C 2.4 E 1.35 C E Package Type: SOT23 Dimensions Value (in mm) C 2.0 X 0.8 X1 1.35 Y 0.9 Y1 2.9 Y C Y1 ` X AH3382 Document number: DS38921 Rev. 1 - 2 X1 13 of 14 www.diodes.com July 2016 © Diodes Incorporated AH3382 IMPORTANT NOTICE NEW PRODUCT DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS DOCUMENT, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION). Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability arising out of the application or use of this document or any product described herein; neither does Diodes Incorporated convey any license under its patent or trademark rights, nor the rights of others. Any Customer or user of this document or products described herein in such applications shall assume all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on Diodes Incorporated website, harmless against all damages. Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel. Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall indemnify and hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized application. Products described herein may be covered by one or more United States, international or foreign patents pending. Product names and markings noted herein may also be covered by one or more United States, international or foreign trademarks. This document is written in English but may be translated into multiple languages for reference. Only the English version of this document is the final and determinative format released by Diodes Incorporated. LIFE SUPPORT Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without the express written approval of the Chief Executive Officer of Diodes Incorporated. As used herein: A. Life support devices or systems are devices or systems which: 1. are intended to implant into the body, or 2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in significant injury to the user. B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or to affect its safety or effectiveness. Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or systems, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of Diodes Incorporated products in such safety-critical, life support devices or systems, notwithstanding any devices- or systems-related information or support that may be provided by Diodes Incorporated. Further, Customers must fully indemnify Diodes Incorporated and its representatives against any damages arising out of the use of Diodes Incorporated products in such safety-critical, life support devices or systems. Copyright © 2016, Diodes Incorporated www.diodes.com AH3382 Document number: DS38921 Rev. 1 - 2 14 of 14 www.diodes.com July 2016 © Diodes Incorporated