APL1117 1A Low Dropout Fast Response Positive Adjustable Regulator and Fixed 1.8V, 2.5V, 2.85V and 3.3V Features General Description • • • The APL1117 is a low dropout three-terminal adjustable regulators with 1A output current capability. In order to obtain lower dropout voltage and faster transient response, which is critical for low voltage applications , the APL1117 has been optimized. The device is available in an adjustable version and fixed output voltages of 1.8V, 2.5V, 2.85V and 3.3V. The output available voltage range of an adjustable version is from 1.25~10.7V with an input supply below 12V. Dropout voltage is guaranteed at a maximum of 1.3V at 1A. Current limit is trimmed to ensure specified output current and controlled short-circuit current. On-chip thermal limiting provides protection against any combination of overload that would create excessive junction temperatures. The APL1117 is available in the industry standard 3-pin TO-220, TO-252, TO263, and the low profile surface mount SOT-223 power packages which can be used in applications where space is limited. Guaranteed Output Voltage Accuracy within 2% Fast Transient Response Guaranteed Dropout Voltage at Multiple Currents • • • • • • • Load Regulation : 0.1% Typ. Line Regulation : 0.03% Typ. Low Dropout Voltage : 1.1V Typ. at IOUT =1A Current Limit : 1A Typ. at TJ=25°C On-Chip Thermal Limiting : 150°C Typ. Adjustable Output : 1.25~10.7V Standard 3-pin TO-220, TO-252, TO-263 and SOT-223 Power Packages Applications • • • • Pin Description Front View for TO-220 Active SCSI Terminators Low Voltage Logic Supplies 3 VIN Battery-Powered Circuitry 2 VOUT Post Regulator for Switching Power Supply 1 ADJ/GND Front View for TO-263 TAB is VOUT 3 VIN 2 VOUT 1 ADJ/GND Front View for TO-252 TAB IS VOUT 3 VIN 2 VOUT 1 ADJ/GND ANPEC reserves the right to make changes to improve reliability or manufacturability without notice, and advise customers to obtain the latest version of relevant information to verify before placing orders. Copyright ANPEC Electronics Corp. Rev. B.8 - Jun., 2003 1 www.anpec.com.tw APL1117 Pin Description (Cont.) Front View for SOT-223 T A B IS V O U T 3 IN 2 OUT 1 A D J /G N D Ordering and Marking Information Package Code F : T O -2 2 0 G : T O -2 6 3 U : T O -2 5 2 Tem p. R ange C : 0 to 7 0 ° C H a n d lin g C o d e TU : Tube TR : Tape & R eel V o lta g e C o d e 1 8 : 1 .8 V 2 5 : 2 .5 V 2 8 : 2 .8 5 V B la n k : A d ju s ta b le V e rs io n APL1117H a n d lin g C o d e Tem p. R ange Package Code V o lta g e C o d e A P L 1 1 1 7 F /G /U : AP L1117 XXXXX V : S O T -2 2 3 3 3 : 3 .3 V XXXXX - D a te C o d e AP L1117 V : AP L1117 XXXXX X X X X X - D a te C o d e A P L 1 1 1 7 -1 8 F /G /U : 18 AP L1117 XXXXX XXXXX - D a te C o d e A P L 1 1 1 7 -1 8 V : AP L1117 XX XXX 18 X X X X X - D a te C o d e A P L 1 1 1 7 -2 5 F /G /U : 25 AP L1117 XXXXX XXXXX - D a te C o d e A P L 1 1 1 7 -2 5 V : AP L1117 XX XXX 25 X X X X X - D a te C o d e A P L 1 1 1 7 -2 8 F /G /U : 28 AP L1117 XXXXX XXXXX - D a te C o d e A P L 1 1 1 7 -2 8 V : AP L1117 XX XXX 28 X X X X X - D a te C o d e 33 A P L 1 1 1 7 -3 3 F /G /U : A P L 1 1 1 7 XXXXX XXXXX - D a te C o d e A P L 1 1 1 7 -3 3 V : AP L1117 XX XXX 33 X X X X X - D a te C o d e Absolute Maximum Ratings Parameter Rating(Note) Unit APL1117, APL1117-33 APL1117-18, APL1117-25, APL1117-28 Operating Junction Temperature Range Control Section Power Transistor Storage Temperature Range 15 9 V Symbol VI TJ TSTG TL Input Voltage Lead Temperature (Soldering, 10 second) °C 0 to 125 0 to 150 -65 to +150 °C 260 °C Note : The values here show the absolute maximum rating, and for normal usage please refer the test condition in Electrical Characteristics Table. Copyright ANPEC Electronics Corp. Rev. B.8 - Jun., 2003 2 www.anpec.com.tw APL1117 Electrical Characteristics (Cont.) Symbol Parameter Test Conditions APL1117 Min. Typ. Max. V REF Reference Voltage 10mA≤ IOUT ≤1A, 1.4V≤(V IN -V OUT) ≤10.75V, 1.225 1.250 1.275 T J =0~125°C V OUT Output Voltage APL1117-18 T J =0~125°C, 0≤ IOUT≤ 1.5A, 3.5V≤V IN≤9V, APL1117-25 T J =0~125°C, 0≤ IOUT≤ 1A, 4V≤V IN≤9V, APL1117-28 T J =0~125°C, 0≤ IOUT≤1A, 4.25V≤V IN≤9V, APL1117-33 T J =0~125°C, 0≤ IOUT≤ 1A, 4.75V≤V IN≤12V, Line Regulation APL1117 IOUT=10mA, 1.5V≤(V IN -V OUT )≤10.75V APL1117-18 IOUT=0A, 3.5V≤V IN≤9V (Note1) APL1117-25 IOUT=0A, 4V≤V IN≤5.5V (Note1) APL1117-28 IOUT=0A, 4.25V≤V IN ≤5.15V (Note1) APL1117-33 I =0A, 4.75V≤V ≤7.75V (Note1) OUT IN Load Regulation APL1117 (V IN -V OUT)=3V, 0≤ IOUT ≤1A (Note1) APL1117-18 V IN=3.5V, 0≤ IOUT ≤1A (Note1) APL1117-25 V IN =4V, 0≤ IOUT ≤1A (Note1) APL1117-28 V IN=4.25V, 0≤ IOUT ≤1A (Note1) APL1117-33 V =4.75V, 0≤ I ≤1A (Note1) IN OUT Dropout Voltage IOUT=100mA (Note2) IOUT=500mA (Note2) IOUT=1A (Note2) Current Limit (V IN -V OUT)=5V, TJ=25°C REG LINE REG LOAD VD ILIMIT IADJ ∆IADJ IO PSRR TR TS LS Adjust Pin Current (V IN -V OUT)=3V, IOUT=10mA APL1117 Adjust Pin Current 10mA≤ IOUT ≤1A, Change APL1117 1.4V≤(VIN -VOUT) ≤10.75V Minimum Load (V IN -V OUT)=10.75V (Note3) Current APL1117 Ripple Rejection fRIPPLE =120Hz, V RIPPLE =1V P-P, (V IN -V OUT)=3V Thermal Regulation T J=25°C, 30ms Pulse Temperature Stability Long -Term Stability T J =125°C,1000Hrs. Copyright ANPEC Electronics Corp. Rev. B.8 - Jun., 2003 3 Unit V 1.764 1.800 1.836 2.450 2.500 2.550 V 2.790 2.850 2.910 3.235 3.300 3.365 (Note1) 0.03 1 1 1 1 0.2 6 6 6 6 % mV 0.1 1 1 1 1 0.4 10 10 10 10 % mV 1 1.05 1.1 1.1 1.2 1.3 1000 60 V mA 60 120 µA 0.2 5 µA 1.7 mA 75 dB 0.01 0.02 %/ W 0.5 % 0.3 % www.anpec.com.tw APL1117 Electrical Characteristics (Cont.) Symbol Parameter Test Conditions VN RMS Output Noise θ th Thermal Resistance Junction to Case, at Tab Junction to Ambient Over Temperature Point Quiescent Current APL1117-18 V IN ≤9V APL1117-25 V IN ≤9V APL1117-28 V IN ≤9V APL1117-33 V ≤12V IN OT IQ T J=25°C,10Hz≤F≤10kHz, (% of V OUT) APL1117 Unit Min. Typ. Max. 0.003 % °C/ W 15 50 150 5.5 5.5 5.5 5.5 °C 10 10 10 10 mA Note 1 : See thermal regulation specifications for changes in output voltage due to heating effects. Load line regulations are measured at a constant junction temperature by low duty cycle pulse testing. Note 2 : Dropout voltage is specified over the full output current range of the device. Dropout voltage is defined as the minimum input/output differential measured at the specified output current. Test points and limits are also shown on the Dropout Voltage curve. Note 3 : Minimum load current is defined as the minimum output current required to maintain regulation. Copyright ANPEC Electronics Corp. Rev. B.8 - Jun., 2003 4 www.anpec.com.tw APL1117 Application Circuits 1.25V to 10.7V Adjustable Regulator VIN IN APL1117 OUT ADJ Improving Ripple Rejection VOUT1 R1 V IN 10µF 121Ω + 10µ F C1* + R2 1k 100µF C2 R2 365 Ω 1% V OUT R1 121 Ω 1% + 150 µ F C1 10µF * C1 improves ripple rejection. XC should be approximately equal to R1 at ripple frequency * Needed if device is far from filter capacitors V O UT = 1.250V X + APL1117 IN OUT ADJ R1 + R2 R1 5V Regulator with Shutdown APL1117 IN OUT ADJ VIN + TTL 10µ F 1k 1k Copyright ANPEC Electronics Corp. Rev. B.8 - Jun., 2003 5V 121Ω 1% + 365Ω 1% 100µF 5 www.anpec.com.tw APL1117 Typical Characteristics Load Transietn Response APL1117-33 5 Line Transient Response 0.02 6 0.01 5 APL1117-33 0.15 Output Current (A) 4 Input Voltage (V) 4.5 3.5 3 0 2.5 CIN=10µF COUT=10µF Tantalum VIN=5V 2 1.5 -0.01 -0.02 1 0.1 4 CIN=10µF COUT=10µF Tantalum IOUT=0.1A 3 0.05 2 0 1 0.5 0 -100 100 300 500 -0.03 900 700 0 -20 30 80 Time (µS) Time (µS) Dropout Voltage vs. Output Current Output Voltage vs. Input Voltage APL1117-33 1.25 3.5 3 1.2 1.15 Output Voltage (V) Dropout Voltage (V) -0.05 180 130 1.1 1.05 1 2.5 2 1.5 1 0.5 0.95 0 0.9 0 0.2 0.4 0.6 0.8 1 0 Output Current (A) Copyright ANPEC Electronics Corp. Rev. B.8 - Jun., 2003 1 2 3 4 5 6 7 8 9 Input Voltage (V) 6 www.anpec.com.tw APL1117 Typical Characteristics Cont. Input Current vs. Input Voltage 6 Current Limit vs. Input Voltage APL1117-33 2.2 Current Limit (A) 5 Input Current (mA) APL1117-33 2.4 4 3 2 1 2 1.8 1.6 1.4 1.2 0 1 0 2 4 6 8 10 12 5 7 Input Voltage (V) 9 11 13 Input Voltage (V) Output Voltage vs. Temperature Output Voltage vs. Temperature 3.4 2.6 2.5 3.3 Output Voltage (V) Output Voltage (V) 2.4 2.3 2.2 2.1 2 1.9 1.8 3.1 3 2.9 2.8 1.7 1.6 -50 3.2 2.7 -25 0 25 50 75 100 125 -50 Temperature (°C) Copyright ANPEC Electronics Corp. Rev. B.8 - Jun., 2003 -25 0 25 50 75 100 125 Temperature (°C) 7 www.anpec.com.tw APL1117 Typical Characteristics Cont. Adjustable Pin Current vs. Temperature 70 68 7 66 64 62 60 58 56 54 6 5 4 3 52 50 -50 -25 0 25 50 75 100 2 -50 125 Temperature (°C) 1.9 0 25 50 75 100 125 PSRR vs. Frequency APL1117-33 APL1117-33 +0 Cadj=22µF -10 IOUT=0.1A Vripple=1Vp-p -20 1.8 1.7 -25 Temperature (°C) Current Limit vs. Temperature VIN-VOUT=5V -30 1.6 PSRR (dB) Current Limit (A) APL1117-33 8 Input Current (mA) Adjustable Pin Current (µA) Input Current vs. Tmeperature APL1117-Adj 1.5 1.4 1.3 -40 -50 -60 VIN-VOUT>=Vdropout -70 1.2 -80 1.1 -90 -100 10 20 1 -50 0 50 100 150 Temperature (°C) Copyright ANPEC Electronics Corp. $ - Jun., 2003 Rev. B.8 VIN-VOUT>=3V 50 100 200 500 1k 2k 5k 10k 20k 50k 200k Frequency (Hz) 8 www.anpec.com.tw APL1117 Application Information Output Voltage The APL1117 develops a 1.25V reference voltage between the output and the adjust terminal. By placing a resistor between these two terminals, a constant Current is caused to flow through R1 and down through R2 to set the overall output voltage. Normally this current is chosen to be the specified minimum load current of 10mA. For fixed voltage devices R1 and R2 are included in the device. APL1117 IN OUT ADJ V IN A P L1117 IN OUT ADJ R1 RL CONNECT R 1 TO C A S E R2 CONNECT R 2 TO LO A D V OUT V REF IADJ 60 µ A V O UT V IN Rp P A R A S IT IC LIN E R E S IS TA N C E Figure 2. Connections for Best Load Regulation R1 Input Capacitor R2 A n i n p u t c a p a c i t o r o f 1 0 µF o r g r e a t e r i s R2 = V REF (1+ )+IADJ R2 R1 recommended. Tantalum, or aluminum electrolytic capacitors can be used for bypassing. Larger Val- Figure 1. Basic Adjustable Regulator ues will improve ripple rejection by bypassing the in- Load Regulation put to the regulator. When the adjustable regulator is used. Load regula- Output Capacitor tion will be limited by the resistance of the wire con- The APL1117 requires an output capacitor to main- necting the regulator to the load. The data sheet speci- tain stability and improve transient response. Proper fication for load regulation is measured at the output capacitor selection is important to ensure proper pin of the device. Best load regulation is obtained operation. The APL1117 output capacitor selection when the top of the resistor divider (R1) is tied di- is dependent upon the ESR (equivalent series rectly to the output pin of the device, not to the load. resistance) of the output capacitor to maintain stability. For fixed voltage devices the top of R1 is internally When the output capacitor is 10uF or greater, the connected to the output, and the ground pin can be output capacitor should have an ESR less than 1Ω. connected to low side of the load. If R1 were con- This will improve transient response as well as pro- nected to the load, RP is multiplied by the divider mote stability. A low-ESR solid tantalum capacitor ratio, the effective resistance between the regulator works extremely well and provides good transient re- and the load would be: Rp X (1+ sponse and stability over temperature. R2 ), Rp = Parasitic Line Resistance R1 Copyright ANPEC Electronics Corp. Rev. B.8 - Jun., 2003 9 www.anpec.com.tw APL1117 Application Information (Cont.) Output Capacitor (Cont.) Figure 3&4 shows for the TO-252 and SOT-223 the measured values of θ(J-A) for different copper area Aluminum electrolytics can also be used, as long as sizes using a 2 layers, 1.6mm, and 6Sq. cm FR-4 the ESR of the capacitor is <1Ω. The value of the PCB with 2oz. copper and a ground plane layer on output capacitor can be increased without limit. Higher the backside area used for heatsinking. It can be capacitance values help to improve transient response used as a rough guideline in estimating thermal and ripple rejection and reduce output noise. resistance. Ripple Rejection Thermal Resistance (Juntion to Ambient) (°C/W) 50 The curves for Ripple Rejection were generated using an adjustable device with the adjust pin bypassed. With a 22µF bypassing capacitor 75dB ripple rejection is obtainable at any output level. The impedance of the adjust pin capacitor, at the ripple frequency, should be < R1. R1 is normally in the range of 100Ω200Ω. The size of the required adjust pin capacitor is a function of the input ripple frequency. At 120Hz, TA=25°C 45 40 35 30 25 0 with R1=100Ω, the adjust pin capacitor should be 2 4 6 8 10 12 14 Top Copper Area (cm2) 13µF. For fixed voltage devices, and adjustable devices without an adjust pin capacitor, the output ripple Figure 3. will increase as the ratio of the output voltage to the θ(J-A) vs. copper area for the SOT-252 package reference voltage (VOUT /VREF ). Thermal Considerations APL1117 has thermal protection which limits junction temperature to 150°C. However, device functionality is only guaranteed to a maximum junction temperature of +125°C. Both the TO-220, TO-252, TO-263 and SOT-223 packages use a copper plane on the PCB and the PCB itself as a heatsink. To optimize the heat sinking ability of the plane and PCB, solder the tab of the package to the plane. Copyright ANPEC Electronics Corp. Rev. B.8 - Jun., 2003 10 www.anpec.com.tw APL1117 Application Information (Cont.) Thermal Considerations (Cont.) Thermal Resistance (Juntion to Ambient) (°C/W) 60 TA=25°C 55 50 45 40 35 30 0 2 4 6 8 10 12 14 Top Copper Area (cm2) Figure 4. θ(J-A) vs. copper area for the SOT-223 package The thermal resistance for each application will be affected by thermal interactions with other components on the board. Some experimentation will be necessary to determine the actual value. The power dissipation of APL1117 is equal to : PD = (VIN - VOUT) x IOUT Maximum junction temperature is equal to : TJUNCTION = TAMBIENT + (PD x θJA) Note: TJUNCTION must not exceed 125°C Copyright ANPEC Electronics Corp. Rev. B.8 - Jun., 2003 11 www.anpec.com.tw APL1117 Package Information TO-220 ( Reference JEDEC Registration TO-220) D R Q b E e b1 e1 L1 L H1 A c F Millimeters Dim A b1 b c D e e1 E F H1 J1 L L1 R Q Min. 3.56 1.14 0.51 0.31 14.23 2.29 4.83 9.65 0.51 5.84 2.03 12.7 3.65 3.53 2.54 Copyright ANPEC Electronics Corp. Rev. B.8 - Jun., 2003 J1 Inches Max. 4.83 1.78 1.14 1.14 16.51 2.79 5.33 10.67 1.40 6.86 2.92 14.73 6.35 4.09 3.43 12 Min. 0.140 0.045 0.020 0.012 0.560 0.090 0.190 0.380 0.020 0.230 0.080 0.500 0.143 0.139 0.100 Max. 0.190 0.070 0.045 0.045 0.650 0.110 0.210 0.420 0.055 0.270 0.115 0.580 0.250 0.161 0.135 www.anpec.com.tw APL1117 Package Informaion TO-252( Reference JEDEC Registration TO-252) E A b2 C1 L2 D H L1 L b C e1 D1 A1 E1 Dim M illim et er s Inc he s M in. M ax. M in. M ax. A 2. 1 8 2. 3 9 0. 0 86 0. 0 94 A1 0. 8 9 1. 2 7 0. 0 35 0. 0 50 b 0. 5 08 0. 8 9 0. 0 20 0. 0 35 b2 5. 2 07 5. 4 61 0. 2 05 0. 2 15 C 0. 4 6 0. 5 8 0. 0 18 0. 0 23 C1 0. 4 6 0. 5 8 0. 0 18 0. 0 23 D 5. 3 34 6. 2 2 0. 2 10 0. 2 45 D1 E 5. 2 R EF 6. 3 5 E1 0. 2 05 R EF 6. 7 3 0. 2 50 5. 3 R EF 0. 2 65 0. 2 09 R EF e1 3. 9 6 5. 1 8 0. 1 56 0. 2 04 H 9. 3 98 10 . 41 0. 3 70 0. 4 10 L 0. 5 1 L1 0. 6 4 1. 0 2 0. 0 25 0. 0 40 L2 0. 8 9 2. 0 32 0. 0 35 0. 0 80 Copyright ANPEC Electronics Corp. Rev. B.8 - Jun., 2003 0. 0 20 13 www.anpec.com.tw APL1117 Package Information TO-263 ( Reference JEDEC Registration TO-263) E L2 E1 T E R M IN A L 4 D1 D L L3 b2 b e e1 A c2 R Φ 1 L1 L4 D E T A IL "A "R O T E D c Millimeters Dim A b b2 c c2 D e e1 L L1 L2 L3 Min. 4.06 0.51 1.14 Inches Max. 4.83 1.016 1.651 Min. 0.160 0.02 0.045 1.40 9.65 10.54 0.045 0.340 0.380 15.88 2.84 2.92 1.78 0.575 0.090 0.040 0.050 0.38 TYP. 1.14 8.64 9.65 0.015 TYP. 2.54 TYP 14.60 2.24 1.02 1.20 Copyright ANPEC Electronics Corp. Rev. B.8 - Jun., 2003 Max. 0.190 0.040 0.065 0.055 0.380 0.415 0.100 TYP 14 0.625 0.110 0.112 0.070 www.anpec.com.tw APL1117 Package Information SOT-223( Reference JEDEC Registration SOT-223) D A B1 a c H E L K e A1 e1 b B Dim A A1 B B1 c D E e e1 H L K α β Millimeters Min. 1.50 0.02 0.60 2.90 0.28 6.30 3.30 Inches Max. 1.80 0.08 0.80 3.10 0.32 6.70 3.70 Min. 0.06 Max. 0.07 0.02 0.11 0.01 0.25 0.13 0.03 0.12 0.01 0.26 0.15 2.3 BSC 4.6 BSC 6.70 0.91 1.50 0° Copyright ANPEC Electronics Corp. Rev. B.8 - Jun., 2003 0.09 BSC 0.18 BSC 7.30 1.10 2.00 10° 13° 0.26 0.04 0.06 0° 0.29 0.04 0.08 10° 13° 15 www.anpec.com.tw APL1117 Physical Specifications Terminal Material Lead Solderability Packaging Solder-Plated Copper (Solder Material : 90/10 or 63/37 SnPb Meets EIA Specification RSI86-91, ANSI/J-STD-002 Category 3. 2500 devices per reel Reflow Condition (IR/Convection or VPR Reflow) temperature Reference JEDEC Standard J-STD-020A APRIL 1999 Peak temperature 183°C Pre-heat temperature Time Classification Reflow Profiles Average ramp-up rate(183 °C to Peak) Preheat temperature 125 ± 25 °C) Temperature maintained above 183 °C Time within 5 °C of actual peak temperature Peak temperature range Ramp-down rate Time 25 °C to peak temperature Convection or IR/ Convection 3 °C/second max. 120 seconds max. 60 ~ 150 seconds 10 ~ 20 seconds 220 +5/-0 °C or 235 +5/-0 °C 6 °C /second max. 6 minutes max. VPR 10 °C /second max. 60 seconds 215~ 219 °C or 235 +5/-0 °C 10 °C /second max. Package Reflow Conditions pkg. thickness ≥ 2.5mm and all bags Convection 220 +5/-0 °C VPR 215-219 °C IR/Convection 220 +5/-0 °C pkg. thickness < 2.5mm and pkg. volume ≥ 350 mm Copyright ANPEC Electronics Corp. Rev. B.8 - Jun., 2003 16 pkg. thickness < 2.5mm and pkg. volume < Convection 235 +5/-0 °C VPR 235 +5/-0 °C IR/Convection 235 +5/-0 °C www.anpec.com.tw APL1117 Reliability test program Test item SOLDERABILITY HOLT PCT TST ESD Latch-Up Method MIL-STD-883D-2003 MIL-STD-883D-1005.7 JESD-22-B, A102 MIL-STD-883D-1011.9 MIL-STD-883D-3015.7 JESD 78 Description 245°C , 5 SEC 1000 Hrs Bias @ 125 °C 168 Hrs, 100 % RH , 121°C -65°C ~ 150°C, 200 Cycles VHBM > 2KV, VMM > 200V 10ms , Itr > 100mA Carrier Tape & Reel Dimension D P Po E t P1 Bo F W Ao D1 Ko T2 J C A B T1 A p p l ic a t i o n T O -2 5 2 A p p l ic a t i o n T O -2 6 3 A p p l ic a t i o n S O T -2 2 3 A B C J 330 ±3 100 ± 2 13 ± 0. 5 2 ± 0 .5 T1 1 6 . 4 + 0 .3 - 0 .2 T2 2 .5 ± 0 .5 W 1 6 + 0 .3 - 0 .1 P 8 ± 0 .1 E 1 . 7 5 ± 0 .1 F D D1 Po P1 Ao Bo Ko t 7 .5 ± 0 .1 1 .5 + 0 .1 1 .5 ± 0 .2 5 4 .0 ± 0 .1 2 .0 ± 0 .1 6 .8 ± 0 .1 1 0 . 4 ± 0 .1 2 .5 ± 0 .1 0 .3 ± 0 .0 5 A B C J T1 T2 P 380±3 80 ± 2 13 ± 0. 5 2 ± 0 .5 24 ± 4 2 ± 0 .3 W 2 4 + 0 .3 - 0 .1 1 6 ± 0 .1 F D D1 Po P1 Ao Bo Ko t 5 .2 ± 0 .1 E 1 .7 5 ± 0 .1 11 .5 ± 0 .1 1 .5 + 0 .1 1 .5 ± 0 .2 5 4 .0 ± 0 .1 2 .0 ± 0 .1 A B J T1 T2 W P 330±1 6 2 ± 1 .5 C 1 2 .7 5 ± 0 .1 5 0 .3 5 ± 0 .0 1 3 E 2 ± 0 .6 1 2 .4 + 0 .2 2 ± 0 .2 1 2 ± 0 .3 8 ± 0 .1 1 .7 5 ± 0 .1 Po P1 F D D1 5 .5 ± 0 .0 5 1 .5 + 0 .1 1 .5 + 0 .1 Copyright ANPEC Electronics Corp. Rev. B.8 - Jun., 2003 4 .0 ± 0 .1 2 .0 ± 0 .0 5 17 1 0 . 8 ± 0 .1 1 6 . 1 ± 0 .1 Ao Bo Ko t 6 .9 ± 0 .1 7 .5 ± 0 .1 2 .1 ± 0 .1 0 .3 ± 0 .0 5 www.anpec.com.tw APL1117 Cover Tape Dimensions Application TO- 252 TO- 263 SOT- 223 Carrier Width 16 24 12 Cover Tape Width 13.3 21.3 9.3 Devices Per Reel 2500 1000 2500 Customer Service Anpec Electronics Corp. Head Office : 5F, No. 2 Li-Hsin Road, SBIP, Hsin-Chu, Taiwan, R.O.C. Tel : 886-3-5642000 Fax : 886-3-5642050 Taipei Branch : 7F, No. 137, Lane 235, Pac Chiao Rd., Hsin Tien City, Taipei Hsien, Taiwan, R. O. C. Tel : 886-2-89191368 Fax : 886-2-89191369 Copyright ANPEC Electronics Corp. Rev. B.8 - Jun., 2003 18 www.anpec.com.tw