Systemsensor A05-0228 500 series intelligent sensors with integral communication Datasheet

500 Series™
Intelligent Sensors with
Integral Communications
A Division of Pittway
3825 Ohio Avenue, St. Charles, IL 60174
1-800-SENSOR2 (736-7672), Fax 630-377-6495
http://www.systemsensor.com
Models Available
1551B Ionization Sensor
2551HR Photoelectronic Sensor
5551B Fixed Temperature Thermal Sensor
2551THR High Resolution Photo Sensor with Thermal
5551R Rate-of-Rise/Fixed Temperature Thermal Sensor
Features
•
•
•
•
•
Low standby current
Shielded electronics
Noise immunity provides stable communications
Compact, stylish design
Sensor plugs easily into base
System Sensor Intelligent Sensors offer features and
performance that surpass conventional sensors. The
sensitivity of models 1551B, 2551HR, and 2551THR can be
“set” individually in the panel software. The sensors may
be continuously monitored for changes in sensitivity and
•
•
•
•
•
Built-in tamper-resist feature
Sealed against dirt, insects, and back pressure
SEMS screws for easy wiring
Easy to use decade address switches
Built-in type ID
compensate for dirt, temperature, or humidity to maintain
the set sensitivity. Model 5551R offers a rate-of-rise
temperature response while the 5551B offers a fixed
temperature response.
Specifications – 2551HR, 2551THR
Dimensions
Height:
Diameter:
Shipping Weight:
Temperature Range
2551HR:
2551THR:
Humidity Range:
Air Velocity Rating:
Operating Voltage:
Standby Current:
© System Sensor 4/97
3.2″ (8.1 cm), detector in base
(add .5″ [1.27 cm] for thermal)
4.0″ (10.2 cm) installed in
B501 base
6.1″ (15.5 cm) installed in
B501B base
9.6 ounces (272 g)
Sensor (2551HR):
Photoelectronic
(scattering principle)
Thermal Sensor
(2551THR):
135° F fixed temperature alarm
Smoke Detector Spacing:
On smooth ceilings (as defined in NFPA 72) spacing of
30 feet (900 sq. ft.) may be used as a guide. See NFPA
72 for more details on spacing requirements.
32° to 120° F (0° to 49° C)
32° to 100° F (0° to 38° C)
10% to 93% RH noncondensing
3,000 fpm
15–32 VDC peak, 6.5 mA
current for visible LEDs
latched on
230 µA
This document is not intended to be used for installation purposes.
APPROVED
MSFM
A05-228-01
General Description
All 500 Series sensors are simple to install, service, and
maintain. Using a specially designed tool (XR5),
maintenance personnel can easily remove and replace the
plug-in detectors without using a ladder. 500 Series
sensors incorporate built-in identification allowing the
system to identify the type of sensor. They also have a
built-in magnetic reed switch for local testing, and the
1551B, 2551HR, and 2551THR can be sensitivity tested
with the MOD400R Field Sensitivity Test Tool.
2551HR/2551THR
The 2551HR Intelligent Photoelectronic Sensor represents
the state of the art in smoke sensor technology. It features
fully coated circuit boards, special insect and dirt
protection and superior RF/transient protection. The
sensor will transmit an analog value representative of the
sensitivity that can be used by the system to determine
when maintenance is required. Signal processing for alarm
verification can be built into the system to provide
immunity to false alarms.
The 2551THR Intelligent Photoelectronic Sensor adds a
thermal heat collector that will alarm at a fixed
temperature of 135° F.
2551THR with
4″ base
1551B
The 1551B Intelligent Ionization Smoke Sensor’s unique
unipolar chamber responds quickly and uniformly to the
broadest range of fires and can withstand wind gusts up to
1500 feet-per-minute without outputting an alarm level
signal. Because of the unipolar chamber, the 1551B is
more responsive than most ionization sensors. This makes
it a more stable detector.
Specifications – 1551B
Dimensions
Height:
Diameter:
Shipping Weight:
Temperature Range:
Humidity Range:
Air Velocity Rating:
Operating Voltage:
Page 2
2.3″ (5.8 cm), detector in base
4.0″ (10.2 cm)
installed in B501 base
6.1″ (15.5 cm)
installed in B501B base
9.5 ounces (269 g)
32° to 120° F (0° to 49° C)
10% to 93% RH noncondensing
1,500 fpm
15–32 VDC peak, 6.5 mA
current for visible LEDs
latched on
1551B with
6″ base
Standby Current:
200 µA
Sensor:
Unipolar, dual chamber
Smoke Detector Spacing:
On smooth ceilings (as defined in NFPA 72) spacing of
30 feet (900 sq. ft.) may be used as a guide. See NFPA
72 for more details on spacing requirements.
A05-228-01
5551B/5551R
The 5551B Intelligent Thermal Sensor’s unique dual
thermistor sensor will alarm at a fixed temperature of
135° F.
The 5551R Intelligent Thermal Sensor will alarm at
135° F and at an increase in excess of 15° per minute. This
enables the heat detector to communicate an alarm to the
central control panel prior to reaching the static set point,
providing a timely response to rapid temperature
increases.
5551R with
6″ base
Specifications – 5551B, 5551R
Dimensions
Height:
Diameter:
Shipping Weight:
Temperature Range:
Humidity Range:
Sensitivity
5551B:
5551R:
2.1″ (5.3 cm) detector in base
4.0″ (10.2 cm)
installed in B501 base
6.1″ (15.5 cm)
installed in B501B base
0.3 lbs. (150 g)
32° to 100° F (0° to 38° C)
10% to 93% RH noncondensing
Operating Voltage:
15–32 VDC peak, 6.5 mA
current for visible LEDs latched on
Standby Current:
200 µA
Sensor:
Electronic, dual thermistors
Thermal Sensor Spacing:
UL listed to 50 ft. spacing. Other spacing may be used
depending on ceiling height and other conditions. See
NFPA 72 for more details on spacing requirements.
135° F fixed temperature alarm
135° F fixed temperature or
15° rise per minute
REMOTE ANNUNCIATOR
+
-
CAUTION: Do not loop wire under terminal 1 or 2.
Break wire run to provide supervision of connections.
U.L. LISTED COMPATIBLE
CONTROL PANEL
+
3
2
3
1
2
3
1
2
1
+
CLASS A OPTIONAL WIRING
500 Series Base
Wiring Diagram
Page 3
A05-228-01
500 Series Junction Box Selection Guide*
Single
Gang
31/2″
Oct.
4″
Oct.
4″
Sq.
50
mm
60
mm
70
mm
75
mm
B501
Yes
No
No
No
Yes
Yes
Yes
No
B501B
Yes
Yes
Yes
Yes
No
No
No
No
B524RB
No
Yes
Yes
Yes
No
Yes
Yes
Yes
B524BI
No
Yes
Yes
Yes
No
No
Yes
Yes
B501BH
No
No
No
Yes
No
No
No
No
* Box depth contingent on base and wire size. Refer to National Electrical Code or applicable local codes for appropriate recommendations.
Ordering Information
Part No.
UL
1551B
2551HR
2551THR
5551B
5551R
B501B
B501
B524RB
B524BI
B501BH
M500MB
M500CH
M500X
M501M
DH500
DH500ACDC
RA400Z
Description
ULC
1551AB
2551AHR
Intelligent Ionization Sensor, Plug-in Head
Intelligent Photoelectronic Sensor, Plug-in
Head
2551TAHR
Intelligent High Resolution Photoelectronic
Sensor with Thermal, Plug-in Head
5551AB
Intelligent Thermal Sensor, Fixed
Temperature (135° F), Plug-in Head
5551RA
Intelligent 135° F Fixed Temperature/Rateof-Rise Thermal Sensor, Plug-in Head
B501B
Flanged Mounting Base, 6.1″ (15.5 cm)
B501
Flangeless Mounting Base, 4″ (10.2 cm)
B524RBA
Intelligent Relay Base, Flanged
B524BIA
Intelligent Isolator Base, Flanged
B501BHA
Sounder Base (includes B501 Base)
M500MAB
Monitor Module, Interfaces with
Mechanical Contact Devices
M500CHA
Control Module, Controls Devices
Requiring External Power
M500X
Isolator Module, Isolates Groups of
Devices Between Two Isolator Modules in
the Event of a Short Circuit Across
Communication Line
M501MA
Mini-Monitor Module
DH500A
Intelligent Duct Housing
DH500ACDCA Intelligent Duct Housing with Auxiliary
Contacts
RA400ZA
Remote Annunciator
Accessories
MOD400R
SMB600
SMK400
RMK400
SMB500
XR5
XP-4
RS14
RS24
RS24T
CRT400
DUST45
Field Sensitivity Test Tool
Surface Mounting Kit for Flanged Base
(B501B)
Surface Mounting Kit for Flangeless Base
(B501)
Recessed Mounting Kit for Flangeless Base
(B501)
Surface Mount Box for 500 Series Modules
Detector Head Removal Tool
Extension Poles for XR5 Detector Removal
Tool
Replacement Screen for 1551B
Replacement Screen for 2551HR
Replacement Screen for 2551THR
Cover Removal Tool for 1551B
Replacement Dust Cover for 500 Series
Smoke Sensors
System Sensor Worldwide Manufacturing & Distribution
In Canada:
Telephone: 905-812-0767
Fax: 905-812-0771
In the Far East:
Telephone: 852-2191-9003
Fax: 852-2736-6580
In Italy:
Telephone: 39-40-9490-111
Fax: 39-40-382137
In China:
Telephone: 852-2191-9003
Fax: 852-2736-6580
In India:
Telefax: 91-022-8202564
In the United Kingdom:
Telephone: 44-1403-276500
Fax: 44-1403-276501
Page 4
A05-228-01
Similar pages