APL5901/2 Low IQ, Low Dropout 900mA Fixed Voltage Regulator Features Built in Current Limit Protection Controlled Short Circuit Current : 200mA Fast Transient Response Short Setting Time SOT-89, SOT-89-5, SOT-223, SO-8 ,TO-252 and TO-252-5 Packages Lead Free Available (RoHS Compliant) • BP 5 1 2 4 3 1 V IN GND VOUT SOT-89 (Top View) 2 3 V OUT GND V IN SOT-89-5 (Top View) Applications TAB is GND Notebook Computer PDA or Portable Equipments Noise-Sensitive Instrumentation Systems General Description IN 1 8 OUT GND 2 7 GND GND 3 6 GND SHDN 4 5 BYP SO-8 (Top View) 1 2 3 V IN GND V OUT SOT-223 (Top View) TAB is GND The APL5901/2 is micropower, low noise, low dropout linear regulator. Operate from 2.7V to 6V input voltage and deliver up to 900mA. Typical output noise is just 50µVRMS with the addition of an external 0.1µF bypass capacitor in BP pin and typical dropout voltage is only 210mV at 900mA loading. Designed for use in battery-powered system, the low 50µA quiescent current makes it an ideal choice. 1 V IN 2 3 TAB is GND • • • GND SHDN TAB is GND 5 • • • • • APL5901 VOUT 4 Built in Thermal Protection BP 3 • Pin Configuration GND 2 • • Low Noise : 50µVRMS (100Hz to 100kHz) Low Quiescent Current : 50µA (No load) Low Dropout Voltage : 210mV (@900mA) Very low Shutdown Current : < 1µA Fixed Output Voltage : 1.3V ~ 3.4V Stable with 4.7µF Output Capacitor Stable with Aluminum , Tantalum or Ceramic Capacitors . Reverse Current Protection No Protection Diodes Needed SHDN 1 • • • • • • • Design with an internal P-channel MOSFET pass transistor, the APL5901/2 maintains a low supply current, independent of the load current and dropout voltage. Other features include reverse current protection, thermal-shutdown protection, current limit protection to ensure specified output current and controlled short-circuit current. The APL5901/2 regulator come in a miniature SOT-89, SOT-89-5, SOT-223, SO8, TO-252 and TO-252-5 packages. VIN V OUT TO-252 (Top View) TO-252-5 (Top View) ANPEC reserves the right to make changes to improve reliability or manufacturability without notice, and advise customers to obtain the latest version of relevant information to verify before placing orders. Copyright ANPEC Electronics Corp. Rev. B.2 - May., 2005 1 www.anpec.com.tw APL5901/2 Pin Configuration (Cont.) APL5902 TAB is V OUT 1 2 3 GND V O U T V IN SOT-223 (Top View) Ordering and Marking Information Package Code D : S OT-89 D5 : SOT-89-5 U : TO-252 U5 : TO-252-5 V : SOT-223 K : SO-8 Temp. Range C : 0 to 70 ° C Handling Code TR : Tape & Reel Voltage Code : 13 : 1.3V ~ 34 : 3.4V Lead Free Code L : Lead Free Device Blank : Original Device APL5901/2 Lead Free Code Handling Code Temp. Range Package Code Voltage Code APL5901/2 - 13 D/V/K : APL5901/2 XXXXX13 XXXXX - Date Code , 13 - 1.3V APL5901/2 - 13 U : 13 APL5901/2 XXXXX XXXXX - Date Code , 13 - 1.3V Note: ANPEC lead-free products contain molding compounds/die attach materials and 100% matte in plate termination finish; which are fully compliant with RoHS and compatible with both SnPb and lead-free soldiering operations. ANPEC lead-free products meet or exceed the lead-free requirements of IPC/JEDEC J STD-020C for MSL classification at lead-free peak reflow temperature. Pin Description No. 1 2 3 4 5 PIN Name VIN I/O Description I Supply voltage input. Ground pins of the circuitry, and all ground pins must be soldered to PCB with proper power dissipation. Shutdown control pin, low = off , high = normal. Don’t leave open. Bypass signal pin in fixed output type device Output pin of the regulator. GND (Note1) SHDN BP(Note1) VOUT I O O Note1 : These pins do not exist in 3-pin package. Copyright ANPEC Electronics Corp. Rev. B.2 - May., 2005 2 www.anpec.com.tw APL5901/2 Absolute Maximum Ratings Symbol VIN, VOUT SHDN Parameter Input Voltage or Out Voltage Shutdown Control Pin RTH,JA Thermal Resistance – Junction to Ambient RTH,JC Thermal Resistance – Junction to Case PD Power Dissipation TJ Operating Junction Temperature Control Section Power Transistor T STG TL Storage Temperature Range Rating 6.5 Unit V 6.5 V SOT-89 : 180 SOT-223 : 135 SO-8 : 150 TO-252 : 50 SOT-89 : 38 SOT-223 : 15 SO-8 : 20 TO-252 : 6 Internally Limited °C/W °C/W W °C 0 to 125 0 to 150 -65 to +150 °C 260 °C Lead Temperature (Soldering, 10 second) Electrical Characteristics Unless otherwise noted these specifications apply over full temperature, VIN=3.6V, CIN=1µF, COUT=4.7µF, SHDN=VIN, TJ=0 to 125°C. Typical values refer to TJ=25°C. Symbol VIN Parameter Test Conditions Input Voltage APL5901/2 Min. Typ. Max. 2.7 6 VOUT ILIMIT Output Voltage Circuit Current Limit VOUT+1.0V< VCC<6.0V, 0mA< IOUT < IMAX VOUT -2% VOUT VOUT +2% VIN=4.3V 1.5 ISHORT IOUT Short Current Load Current VOUT=0V (Note2) Dropout Voltage PSRR Ripple Rejection IQ Quiescent Current Shutdown Supply (Note3) Current VOUT+0.5V< VCC<6.0V, I = 1mA VIN =VOUT+1.0V, 0mA< IOUT < IMAX IOUT =900mA 1300 1.5V≤VOUT<2V 900 1050 2V≤VOUT<2.5V 500 700 2.5V≤VOUT<3.4V 280 380 55 10 6 65 100 IOUT=900mA 370 450 Shutdown = low IOUT=0, VCC =6.0V 0.01 1 3 V A mV mV % mV dB 50 Copyright ANPEC Electronics Corp. Rev. B.2 - May., 2005 1.3V≤VOUT<1.5V 515X 4 1 0.1 1100 F≤1kHz, 1Vpp at VIN = VOUT+1.0V C load =10nf No V mA mA 900 REGLINE Line Regulation REGLOAD Load Regulation VDROP 200 Unit µA µA www.anpec.com.tw APL5901/2 Electrical Characteristics (Cont.) Unless otherwise noted these specifications apply over full temperature, VIN=3.6V, CIN=1µF, COUT=4.7µF, SHDN=VIN, TJ=0 to 125°C. Typical values refer to TJ=25°C. Symbol Parameter 100Hz<f<100kHz, typical load, CBP=0.01µF, COUT = 1µF 100Hz<f<100kHz, typical load, CBP=0.1µF, COUT = 1µF (Note3) Noise IQ Shutdown Recovery (Note3) Delay OTS APL5901/2 Min. Typ. Max. Test Conditions Over Temperature Shutdown Over Temperature Shutdown Hysteresis 50 µVrms 40 CBP=0.01µF,COUT=1µF, no load 7 CBP=0.1µF,COUT=1µF, no load 70 Hysteries Output Voltage Temperature Coefficient TC COUT Unit Output Capacitor 4.2 ms 150 °C 10 °C 50 ppm/°C 4.7 µF 5.2 ESR 0.02 0.1 1 Ohm Shutdown Input VOUT+1.0V< VIN <6.0V 0.4 0.7 1.6 V Threshold(Note3) Shutdown input Bias ISHDN VSHDN =VIN 0.01 100 nA current(Note3) Input Reverse Leakage µA VOUT-VIN=0.1V 0.1 0.5 current Reverse Protection 11 50 mV Threshold Note 2 : Dropout voltage definition : VIN-VOUT when VOUT is 2% below the value of VOUT for VIN = VOUT + 0.5V Note 3 : For 5-pin devices only. Application Circuit INPUT 2.7V to 6V VIN VOUT VOUT APL5901 C IN 1µ F BP SHDN on C OUT 4.7 µ F GND off C BP Copyright ANPEC Electronics Corp. Rev. B.2 - May., 2005 4 0.01 µ F www.anpec.com.tw APL5901/2 Typical Characteristics Ground Pin Current vs. Load Current (uA) Current Limit vs. Input Voltage APL5901/2-33 3 Current Limit (mA) 2.5 2 1.5 1 0.5 0 3.5 4 4.5 5 5.5 6 Ground Pin Current vs. Output Current APL5901/2-33 400 350 300 250 200 150 100 50 0 0 150 Ground Pin Current vs. Input Voltage 600 750 900 Input Voltage vs. Output Voltage APL5901/2-33 APL5901/2-33 3.5 3 300 Output Voltage (V) Ground Pin Current vs. Load Current (uA) 450 Output Current (mA) Input Voltage (V) 350 300 250 200 150 100 2.5 2 1.5 1 0.5 50 0 0 0 1 2 3 4 5 0 6 Input Voltage (V) Copyright ANPEC Electronics Corp. Rev. B.2 - May., 2005 1 2 3 4 5 6 Input Voltage (V) 5 www.anpec.com.tw APL5901/2 Typical Characteristics Output Current vs. Output Voltage Dropout Voltage vs. Output Current 1200 APL5901/2-33 0 1100 VOUT=1.5V -2 Output Current (uA) Dropout Voltage (mV) 1000 900 800 VOUT=1.8V 700 600 500 VOUT=3.3V 400 300 VOUT=2.5V 200 -4 VIN=0V -6 -8 -10 100 0 -12 0 150 300 450 600 750 0 900 0.5 1 Output Current (mA) 1.5 2 2.5 Output Voltage (V) SHDN Threshold Voltage vs. Input Voltage PSRR vs. Frequency APL5901/2-33 APL5901/2-33 1 3 0.9 -20 0.8 VIN=0V PSRR (dB) SHDN Threshold Voltage (V) +0 -10 0.7 0.6 VIN=4V -30 -40 IOUT =50mA COUT=10uF CBP=0.1uF -50 -60 -70 0.5 VIN=5V -80 -90 0.4 3 3.5 4 4.5 5 5.5 -100 6 Input Voltage (V) Copyright ANPEC Electronics Corp. Rev. B.2 - May., 2005 20 50 100 200 500 1k 2k 5k 10k 20k 50k 100k 200k Frequency (HZ) 6 www.anpec.com.tw APL5901/2 Typical Characteristics Output Noise vs. Bypass Capacitor Output Noise APL5901/2-33 100u 450 400 40u Output Noise (uV) VOUT (50uV/div) APL5901/2-33 500 VIN=4.3V 80u IOUT =0mA COUT=10uF 60u CBP=0.1uF 20u 0 -20u -40u -60u 350 300 250 200 150 100 50 -80u -100u 0 0 4m 2m 6m 8m 10m 0 0.1 0.2 0.3 Bypass Capacitor (uF) Time (s) Load-Transient Response Line-Transient Response APL5901/2-33 Output Voltage (20mV/div) Output Voltage (50mV/div) APL5901/2-33 VOUT VIN=VOUT+1V COUT=4.7µF IOUT=1mA~900mA Time (10µs/div) Copyright ANPEC Electronics Corp. Rev. B.2 - May., 2005 0.4 VIN 4V 3V VOUT Time (40µs/div) 7 www.anpec.com.tw APL5901/2 Typical Characteristics Shutdown Exit Delay Shutdown Exit Delay APL5901/2-33 APL5901/2-33 3.3V 3.3V VOUT VOUT CBP=10nF No Load CBP=100nF No Load 0V 0V 4V 4V vSHDN vSHDN 0V 0V Time (20ms/div) Time (1ms/div) Region of Stable ESR vs. Load Current Entering Shutdown APL5901/2-33 APL5901/2-33 1 3.3V VOUT=3.3V COUT ESR (Ω) VOUT COUT=1µF No Load 0V 4V 0.1 stable 0.01 unstable 0V 0.001 0 Time (200ms/div) Copyright ANPEC Electronics Corp. Rev. B.2 - May., 2005 150 300 450 600 750 900 Load Current (mA) 8 www.anpec.com.tw APL5901/2 Typical Characteristics Output Voltage vs. Temperature APL5901/2-33 3.35 Output Voltage (V) 3.33 3.31 3.29 3.27 3.25 -40 0 40 80 120 Temperature (°C ) Copyright ANPEC Electronics Corp. Rev. B.2 - May., 2005 9 www.anpec.com.tw APL5901/2 Application Information Reverse Current Protection Capacitor Selection and Regulator Stability The APL5901/2 have an internal reverse protection, it does not need an external schottky diode to connect the regulator input and output. If the output voltage is forced above the input voltage by more than 11mV, the IC will be shutdown and the ground pin current is below 0.1uA. The APL5901/2 use at least a 1µF capacitor on the input, and this capacitor can be Aluminum, Tantalum or Ceramic capacitor. The input capacitor with larger value and lower ESR provides better PSRR and linetransient response. The output capacitor also can use Aluminum, Tantalum or Ceramic capacitor, and a minimum value of 4.7µF and ESR above 0.02Ω is recommended. A larger output capacitor can reduce noise and improve load-transient response, stability, and PSRR. Note that some ceramic dielectrics exhibit large capacitance and ESR variation with temperature. When using this capacitor, a minimum 10uF or more may be required to ensure the stability at low temperature operation. Use a bypass capacitor at BP pin for low output nvise. Increasing the capacitance will slightly decrease the output noise, but increase the start-up time. Shutdown/Enable The APL5901/2 have an active high enable function. Force EN high (>1.6V) enables the regulator, EN low (<0.4V) disables the regulator and enter the shutdown mode. In shutdown mode, the quiescent current can reduce below 1uA. The EN pin cannot be floating, a floating EN pin may cause an indeterminate state on the output. If it is no use, connect to VIN for normal operation. Load-Transient Considerations Current Limit The APL5901/2 load-transient response graphs in typical characteristics show the transient response. A step change in the load current from 10mA to 900mA at 10µs will cause a 20mV transient spike. Larger output capacitor and lower ESR can reduce transient spike. The APL5901/2 have a current limit protection. The ouptut voltage will drop close to zero volt, when load current reaches the limit, and then the load current will be limited at 200mA after output voltage is below 0.7V. When the load current back to the value where limiting started, the output voltage and current will return to normal value. When output is shorted to ground, the APL5901/2 will keep short circuit current at 200mA . Input-Output (Dropout)Voltage The minimum input-output voltage difference (dropout) determines the lowest usable supply voltage. In battery-powered systems, this will determine the useful end-of-life battery voltage. Because the APL5901/2 use a p-channel MOSFET pass transistor, the dropout voltage is a function of drain-to-source on-resistance (RDS(ON)) multiplied by the load current. Copyright ANPEC Electronics Corp. Rev. B.2 - May., 2005 10 www.anpec.com.tw APL5901/2 Thermal Protection Thermal protection limits total power dissipation in the device. When the junction temperature exceeds TJ=+150℃, the thermal sensor generates a logic signal to turn off the pass transistor and allows IC to cool. When the IC’s junction temperature is down by 10℃, the thermal sensor will turn the pass transistor on again, resulting in a pulsed output during continuous thermal protection. Thermal protection is designed to protect the APL5901/2 in the event of fault conditions. For continuous operation, do not exceed the absolute maximum junction temperature of TJ=+150℃. Operating Region and Power Dissipation The thermal resistance of the case to circuit board, and the rate of air flow all control the APL5901/2’s maximum power dissipation. The power dissipation across the device is PD = IOUT (VIN-VOUT) and the maximum power dissipation is: PDMAX = (TJ-T A) / (θ JC + θ CA) where TJ-TA is the temperature difference between the junction and ambient air, θ JC is the thermal resistance of the package, and θ CA is the thermal resistance through the printed circuit board, copper traces, and other materials to the ambient air. The GND pin of the APL5901 provide an electrical connection to ground and channeling heat away. If power dissipation is large, connect the GND pin to ground using a large pad or ground plane, can improve the problem of over heat of IC. Copyright ANPEC Electronics Corp. Rev. B.2 - May., 2005 11 www.anpec.com.tw APL5901/2 Packaging Information E e1 0.015X45 SOP-8 pin ( Reference JEDEC Registration MS-012) H e2 D A1 A 1 L 0.004max. Dim Millimeters Inches Min. Max. Min. Max. A 1.35 1.75 0.053 0.069 A1 0.10 0.25 0.004 0.010 D 4.80 5.00 0.189 0.197 E 3.80 4.00 0.150 0.157 H 5.80 6.20 0.228 0.244 L 0.40 1.27 0.016 0.050 e1 0.33 0.51 0.013 0.020 e2 1.27BSC 0.50BSC φ 1 8° 8° Copyright ANPEC Electronics Corp. Rev. B.2 - May., 2005 12 www.anpec.com.tw APL5901/2 Packaging Information SOT-223( Reference JEDEC Registration SOT-223) D A B1 a c H E L K e A1 e1 b B Dim A A1 B B1 c D E e e1 H L K α β Millimeters Min. 1.50 0.02 0.60 2.90 0.28 6.30 3.30 Min. 0.06 Max. 0.07 0.02 0.11 0.01 0.25 0.13 0.03 0.12 0.01 0.26 0.15 2.3 BSC 4.6 BSC 6.70 0.91 1.50 0° Copyright ANPEC Electronics Corp. Rev. B.2 - May., 2005 Inches Max. 1.80 0.08 0.80 3.10 0.32 6.70 3.70 0.09 BSC 0.18 BSC 7.30 1.10 2.00 10° 13° 0.26 0.04 0.06 0° 0.29 0.04 0.08 10° 13° 13 www.anpec.com.tw APL5901/2 Packaging Information SOT-89 (Reference EIAJ ED-7500A Reg stration SC-62) D D1 a E H 1 2 3 L C B1 B e e1 A a Dim A B B1 C D D1 e e1 E H L α Millimeters Min. 1.40 0.40 0.35 0.35 4.40 1.35 Min. 0.055 0.016 0.014 0.014 0.173 0.053 1.50 BSC 3.00 BSC 2.29 3.75 0.80 Copyright ANPEC Electronics Corp. Rev. B.2 - May., 2005 Inches Max. 1.60 0.56 0.48 0.44 4.60 1.83 Max. 0.063 0.022 0.019 0.017 0.181 0.072 0.059 BSC 0.118 BSC 2.60 4.25 1.20 10° 14 0.090 0.148 0.031 0.102 0.167 0.047 10° www.anpec.com.tw APL5901/2 Packaging Information SOT-89-5 Dim A B C D E F G H I J K L Millimeters Min. 4.40 4.05 1.50 1.30 2.40 0.80 Min. 0.17 0.16 0.06 0.05 0.09 0.03 3.00 REF 1.50 REF 0.40 1.40 0.35 Copyright ANPEC Electronics Corp. Rev. B.2 - May., 2005 Inches Max. 4.60 4.25 1.70 1.50 2.60 - Max. 0.18 0.17 0.07 0.06 0.1 0.12 REF 0.06 REF 0.52 1.60 0.41 5 TYP 0.01 0.05 0.01 0.02 0.06 0.02 0.2 TYP 15 www.anpec.com.tw APL5901/2 Packaging Information TO-252-5 H A J D M C B K L S Dim A B C D P S H J K L M P Millimeters Min. 6.40 5.20 6.80 2.20 Inches Max. 6.80 5.50 7.20 2.80 1.27 REF Max. 0.26 0.21 0.27 0.11 0.05 REF 0.50 2.20 0.45 0 0.90 5.40 0.80 2.40 0.55 0.15 1.50 5.80 Copyright ANPEC Electronics Corp. 16 Rev. B.2 - May., 2005 Min. 0.25 0.20 0.26 0.08 0.02 0.08 0.01 0 0.03 0.21 0.03 0.09 0.02 0.006 0.06 0.22 www.anpec.com.tw APL5901/2 Packaging Information TO-252( Reference JEDEC Registration TO-252) E A b2 C1 L2 D H L1 L b C e1 Dim A1 Millimeters Inches Min. Max. Min. Max. A 2.18 2.39 0.086 0.094 A1 0.89 1.27 0.035 0.050 b 0.508 0.89 0.020 0.035 b2 5.207 5.461 0.205 0.215 C 0.46 0.58 0.018 0.023 C1 0.46 0.58 0.018 0.023 D 5.334 6.22 0.210 0.245 E 6.35 6.73 0.250 0.265 e1 3.96 5.18 0.156 0.204 H 9.398 10.41 0.370 0.410 L 0.51 L1 0.64 1.02 0.025 0.040 L2 0.89 2.032 0.035 0.080 Copyright ANPEC Electronics Corp. Rev. B.2 - May., 2005 0.020 17 www.anpec.com.tw APL5901/2 Physical Specifications Terminal Material Lead Solderability Solder-Plated Copper (Solder Material : 90/10 or 63/37 SnPb), 100%Sn Meets EIA Specification RSI86-91, ANSI/J-STD-002 Category 3. Reflow Condition (IR/Convection or VPR Reflow) tp TP Critical Zone T L to T P Temperature Ramp-up TL tL Tsmax Tsmin Ramp-down ts Preheat 25 t 25 °C to Peak Time Classificatin Reflow Profiles Profile Feature Average ramp-up rate (TL to TP) Preheat - Temperature Min (Tsmin) - Temperature Max (Tsmax) - Time (min to max) (ts) Time maintained above: - Temperature (T L) - Time (tL) Peak/Classificatioon Temperature (Tp) Time within 5°C of actual Peak Temperature (tp) Ramp-down Rate Sn-Pb Eutectic Assembly Pb-Free Assembly 3°C/second max. 3°C/second max. 100°C 150°C 60-120 seconds 150°C 200°C 60-180 seconds 183°C 60-150 seconds 217°C 60-150 seconds See table 1 See table 2 10-30 seconds 20-40 seconds 6°C/second max. 6°C/second max. 6 minutes max. 8 minutes max. Time 25°C to Peak Temperature Notes: All temperatures refer to topside of the package .Measured on the body surface. (mm) Copyright ANPEC Electronics Corp. Rev. B.2 - May., 2005 18 www.anpec.com.tw APL5901/2 Classification Reflow Profiles(Cont.) Table 1. SnPb Entectic Process – Package Peak Reflow Temperature s 3 3 Package Thickness Volume mm Volume mm <350 ≥350 <2.5 mm 240 +0/-5°C 225 +0/-5°C ≥2.5 mm 225 +0/-5°C 225 +0/-5°C Table 2. Pb-free Process – Package Classification Reflow Temperatures 3 3 3 Package Thickness Volume mm Volume mm Volume mm <350 350-2000 >2000 <1.6 mm 260 +0°C* 260 +0°C* 260 +0°C* 1.6 mm – 2.5 mm 260 +0°C* 250 +0°C* 245 +0°C* ≥2.5 mm 250 +0°C* 245 +0°C* 245 +0°C* *Tolerance: The device manufacturer/supplier shall assure process compatibility up to and including the stated classification temperature (this means Peak reflow temperature +0°C. For example 260°C+0°C) at the rated MSL level. Reliability Test Program Test item SOLDERABILITY HOLT PCT TST ESD Latch-Up Method MIL-STD-883D-2003 MIL-STD-883D-1005.7 JESD-22-B,A102 MIL-STD-883D-1011.9 MIL-STD-883D-3015.7 JESD 78 Description 245°C, 5 SEC 1000 Hrs Bias @125°C 168 Hrs, 100%RH, 121°C -65°C~150°C, 200 Cycles VHBM > 2KV, VMM > 200V 10ms, 1tr > 100mA Carrier Tape & Reel Dimensions t D P Po E P1 Bo F W Ko Ao Copyright ANPEC Electronics Corp. Rev. B.2 - May., 2005 D1 19 www.anpec.com.tw APL5901/2 Carrier Tape & Reel Dimensions(Cont.) T2 J C A B T1 Reel Dimensions Application SOP- 8 Application SOT-89 Application SOT-223 Application TO-252 A B C J T1 T2 W P E 330 ± 1 62 +1.5 12.75+ 0.15 2 ± 0.5 12.4 ± 0.2 2 ± 0.2 12 ± 0. 3 8± 0.1 1.75 ±0.1 F D D1 Po P1 Ao Bo Ko t 5.5 ± 1 1.55 +0.1 1.55+ 0.25 4.0 ± 0.1 2.0 ± 0.1 6.4 ± 0.1 5.2± 0. 1 2.1 ± 0.1 0.3 ±0.013 A B C J T1 T2 P E 178 ±1 70 ± 2 13.5 ± 0.15 3 ± 0.15 14 ± 2 1.3 ± 0.3 W 12 + 0.3 12 - 0.1 8 ± 0.1 1.75± 0.1 F D D1 Po P1 Ao Bo Ko t 5.5 ± 0.05 1.5± 0.1 1.5 ± 0.1 4.0 ± 0.1 2.0 ± 0.1 4.8 ± 0.1 4.5± 0.1 1.80± 0.1 0.3 ±0.013 A B T1 T2 W P E 62±1.5 C 12.75 ± 0.15 J 330±1 2 ± 0.6 12.4 +0.2 2 ± 0.2 12 ± 0.3 8 ± 0.1 1.75± 0.1 F D D1 Po P1 Ao Bo Ko t 5.5 ± 0.05 1.5+ 0.1 1.5+ 0.1 4.0 ± 0.1 2.0 ± 0.05 6.9 ± 0.1 7.5± 0.1 2.1 ± 0.1 0.3 ±0.05 A B C J T2 E 100 ± 2 13 ± 0. 5 2 ± 0.5 2.5 ± 0.5 W 16+ 0.3 - 0.1 P 330 ±3 T1 16.4 + 0.3 -0.2 8 ± 0.1 1.75± 0.1 F D D1 Po P1 Ao Bo Ko t 7.5 ± 0.1 1.5 +0.1 1.5± 0.25 4.0 ± 0.1 2.0 ± 0.1 6.8 ± 0.1 10.4 ± 0.1 2.5 ± 0.1 0.3 ±0.05 (mm) Cover Tape Dimensions Application SOP- 8 SOT- 89 SOT- 223 TO- 252 Carrier Width 12 12 12 16 Copyright ANPEC Electronics Corp. Rev. B.2 - May., 2005 Cover Tape Width 9.3 9.3 9.3 13.3 20 Devices Per Reel 2500 1000 2500 2500 www.anpec.com.tw APL5901/2 Customer Service Anpec Electronics Corp. Head Office : 5F, No. 2 Li-Hsin Road, SBIP, Hsin-Chu, Taiwan, R.O.C. Tel : 886-3-5642000 Fax : 886-3-5642050 Taipei Branch : 7F, No. 137, Lane 235, Pac Chiao Rd., Hsin Tien City, Taipei Hsien, Taiwan, R. O. C. Tel : 886-2-89191368 Fax : 886-2-89191369 Copyright ANPEC Electronics Corp. Rev. B.2 - May., 2005 21 www.anpec.com.tw