AZ Displays ATM0430D5-T Liquid crystal display Datasheet

AZ DISPLAYS
SPECIFICATIONS FOR
LIQUID CRYSTAL DISPLAY
CUSTOMER APPROVAL
※ PART NO. :
APPROVAL
ATM0430D5-T(AZDISPLAYS) VER1.0
COMPANY
CHOP
CUSTOMER
COMMENTS
AZ DISPLAYS ENGINEERING APPROVAL
DESIGNED BY
CHECKED BY
APPROVED BY
ATM0430D5-T(AZ DISPLAYS) TFT MODUL VER1.0
REVISION RECORD
Date
Rev.No.
2010.05.16 V1.0
AZ DISPLAYS
Page
Revision Items
Prepared
The first release
2
ATM0430D5-T(AZ DISPLAYS) TFT MODUL VER1.0
Contents
1. General Specifications ………………………………………………………………………………1
2. Pin Assignment ……………………………………………………………………………………...2
2.1. TFT LCD Panel Driving Section...................................................................................... 2
2.2. Touch Screen Panel Section............................................................................................ 4
3. Operation Specifications………………………………………………………………………………5
3.1. Absolute Maximum Ratings ............................................................................................ 5
3.2. Typical operation conditions ........................................................................................... 6
3.3
Backlight Driving Conditions .......................................................................................... 6
3.4. Power Sequence ............................................................................................................ 7
3.5. Timing Characteristics .................................................................................................... 8
3.5.1. Timing Conditions ................................................................................................... 8
3.5.2. Timing Diagram ...................................................................................................... 9
4. Touch Screen Panel Specifications
……………………………………………………………..10
4.1. Electrical Characteristics .............................................................................................. 10
4.2. Mechanical & Reliability Characteristics ........................................................................ 11
4.3. Linearity Definition ......................................................................................................... 12
4.4. Housing design guide ……………………………………………………………………………..13
5. Optical Specifications …………………………………………………………………………….....14
6. Reliability Test Items ……………………………………………………………………………….18
7. General Precautions ……………………………………………………………………………….19
7.1. Safety ............................................................................................................................ 19
7.2. Handling ........................................................................................................................ 19
7.3. Static Electricity.............................................................................................................. 19
7.4. Storage .......................................................................................................................... 19
7.5. Cleaning ........................................................................................................................ 19
8. Mechanical Drawing ……………………………………………………………………………….20
9. Package Drawing
……………………………………………………………………………….21
9.1. Packaging Material Table............................................................................................... 21
9.2. Packaging Quantity........................................................................................................ 21
9.3. Packaging Drawing........................................................................................................ 22
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
AZ DISPLAYS
3
ATM0430D5-T(AZ DISPLAYS) TFT MODUL VER1.0
CHIMEI INNOLUX
SPEC NO.: A043-24-TT-71
Date : 2010/04/19
1. General Specifications
No.
Item
Specification
1
LCD size
4.3 inch(Diagonal)
2
Driver element
a-Si TFT active matrix
3
Resolution
480 × 3 (RGB) × 272
4
Display mode
Normally White, Transmissive
5
Dot pitch
0.066(W) × 0.198(H) mm
6
Active area
95.04(W) × 53.856(H) mm
7
Module size
105.5(W) × 67.2(H) × 4.05(D) mm
8
Surface treatment
Anti-Glare
9
Color arrangement
RGB-stripe
10
Interface
Digital
11
Backlight Power consumption 0.558 W(Typ.)
12
Panel Power consumption
0.056 W (Typ.)
13
Weight
TBD (Typ.)
Remark
Note 1
Note 1: Refer to Mechanical Drawing.
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
AZ DISPLAYS
4
ATM0430D5-T(AZ DISPLAYS) TFT MODUL VER1.0
CHIMEI INNOLUX
SPEC NO.: A043-24-TT-71
Date : 2010/04/19
2. Pin Assignment
2.1.TFT LCD Panel Driving Section
FPC Connector is used for the module electronics interface. The recommended model
is “FH19SC-40S-0.5SH” manufactured by HIROSE.
Pin No.
Symbol
I/O
Function
1
VLED-
P
Power for LED backlight cathode
2
VLED+
P
Power for LED backlight anode
3
GND
P
Power ground
4
VDD
P
Power voltage
5
R0
I
Red data (LSB)
6
R1
I
Red data
7
R2
I
Red data
8
R3
I
Red data
9
R4
I
Red data
10
R5
I
Red data
11
R6
I
Red data
12
R7
I
Red data (MSB)
13
G0
I
Green data (LSB)
14
G1
I
Green data
15
G2
I
Green data
16
G3
I
Green data
17
G4
I
Green data
18
G5
I
Green data
19
G6
I
Green data
20
G7
I
Green data (MSB)
Remark
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
AZ DISPLAYS
5
ATM0430D5-T(AZ DISPLAYS) TFT MODUL VER1.0
CHIMEI INNOLUX
SPEC NO.: A043-24-TT-71
Date : 2010/04/19
21
B0
I
Blue data (LSB)
22
B1
I
Blue data
23
B2
I
Blue data
24
B3
I
Blue data
25
B4
I
Blue data
26
B5
I
Blue data
27
B6
I
Blue data
28
B7
I
Blue data (MSB)
29
GND
P
Power ground
30
CLK
I
Pixel clock
31
DISP
I
Display on/off
32
NC
-
No connection
33
NC
-
No connection
34
DE
I
Data Enable
35
NC
-
No connection
36
GND
P
Power ground
37
X1
I/O
Right electrode – differential analog
38
Y1
I/O
Bottom electrode – differential analog
39
X2
I/O
Left electrode – differential analog
40
Y2
I/O
Top electrode – differential analog
I: input, O: output, P: Power
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
AZ DISPLAYS
6
ATM0430D5-T(AZ DISPLAYS) TFT MODUL VER1.0
CHIMEI INNOLUX
SPEC NO.: A043-24-TT-71
Date : 2010/04/19
2.2. Touch Screen Panel Section
Pin No.
Symbol
I/O
Function
Remark
1
X1
Right
2
Y1
Bottom
3
X2
Left
Left electrode – differential analog
4
Y2
Top
Top electrode – differential analog
Right electrode – differential analog
Bottom electrode – differential analog
Note: Touch Screen Panel Block
Top View
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
AZ DISPLAYS
7
ATM0430D5-T(AZ DISPLAYS) TFT MODUL VER1.0
CHIMEI INNOLUX
SPEC NO.: A043-24-TT-71
Date : 2010/04/19
3. Operation Specifications
3.1. Absolute Maximum Ratings
(Note 1)
Values
Item
Symbol
Unit
Remark
Min.
Max.
VDD
-0.5
5.0
V
Logic input
-0.5
5.0
V
Operation temperature
TOP
-20
70
℃
Note 3, 4
Storage temperature
TST
-30
80
℃
Note 3, 4
LED Reverse Voltage
VR
-
1.2
V
Each LED
Note 2
LED Forward Current
IF
-
25
mA
Each LED
Power voltage
Input signal voltage
Note 1: The absolute maximum rating values of this product are not allowed to be
exceeded at any times. A module should be used with any of the absolute
maximum ratings exceeded, the characteristics of the module may not be
recovered, or in an extreme condition, the module may be permanently
destroyed.
Note 2: VR Conditions: Zener Diode 20mA
Note 3: 90% RH Max. (Max wet temp. is 60℃)
Maximum wet-bulb temperature is at 60℃ or less. And No condensation (no
drops of dew)
+60℃
℃, 90%RH
(℃)
Note 4: In case of temperature below 0℃,the response time of liquid crystal (LC) becomes
slower and the color of panel darker than normal one.
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
AZ DISPLAYS
8
ATM0430D5-T(AZ DISPLAYS) TFT MODUL VER1.0
CHIMEI INNOLUX
SPEC NO.: A043-24-TT-71
Date : 2010/04/19
3.2. Typical operation conditions
Values
Item
Symbol
Unit
Min.
Typ.
Max.
Power voltage
VDD
3.1
3.3
3.5
V
Current for Driver
IVDD
-
17
25
mA
Input logic high voltage
VIH
0.8VDD
-
VDD
V
Remark
VDD = 3.3V
Note 1
Input logic low voltage
VIL
GND
-
0.2VDD
V
Note1: CLK, DE, R0~ R7, G0~ G7, B0~ B7.
3.3 Backlight Driving Conditions
Values
Item
Symbol
Unit
Min.
Typ.
Max.
Voltage for LED Backlight
VL
25.2
27.9
31.5
V
Current for LED Backlight
IL
18
20
22
mA
LED life time
-
20,000
-
-
Hr
Remark
Note 2
Note 1
Note 1: The “LED life time” is defined as the module brightness decrease to 50%
original brightness that the ambient temperature is 25℃ and IL =20mA. The
LED lifetime could be decreased if operating IL is lager than 20 mA.
Note 2: The LED Supply Voltage is defined by the number of LED at Ta=25℃ and
IL =20mA.
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
AZ DISPLAYS
9
ATM0430D5-T(AZ DISPLAYS) TFT MODUL VER1.0
CHIMEI INNOLUX
SPEC NO.: A043-24-TT-71
Date : 2010/04/19
3.4. Power Sequence
To prevent a latch-up or DC operation of the LCD module, the power on/off sequence
should be as the diagram below.
Symbol
Specification
Symbol
Specification
T1
0≦T1≦10 msec
T4
160 msec ≦T4
T2
0≦T2≦100 msec
T5
160 msec ≦T5
T3
0≦T3≦200 msec
T6
1 msec ≦T6
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
AZ DISPLAYS
10
ATM0430D5-T(AZ DISPLAYS) TFT MODUL VER1.0
CHIMEI INNOLUX
SPEC NO.: A043-24-TT-71
Date : 2010/04/19
3.5. Timing Characteristics
3.5.1.
Timing Conditions
Parallel DE mode RGB input timing table
Value
Parameter
Symbol
Unit
Min.
Typ.
Max.
CLK frequency
fclk
7
9
12
MHz
DEV period time
Tv
277
288
400
H
DEV display area
Tvd
DEV blanking
Tvb
5
16
128
H
DEH period time
Th
520
525
800
CLK
DEH display area
Thd
DEH blanking
Thb
40
45
320
CLK
CLK cycle time
Tclk
83
110
143
ns
Clock width of high level
Tcwh
40
50
60
%
Clock width of low level
Tcwl
40
50
60
%
Clock rising time
trck
-
9
ns
Clock falling time
tfck
-
9
ns
Data Setup Time
tdesu
10
-
-
ns
Data Hold Time
tdahd
10
-
-
ns
DE Setup Time
tdesu
10
-
-
ns
DE Hold Time
tdehd
10
-
-
ns
272
H
480
CLK
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
AZ DISPLAYS
11
ATM0430D5-T(AZ DISPLAYS) TFT MODUL VER1.0
CHIMEI INNOLUX
SPEC NO.: A043-24-TT-71
Date : 2010/04/19
3.5.2.
Timing Diagram
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
AZ DISPLAYS
12
ATM0430D5-T(AZ DISPLAYS) TFT MODUL VER1.0
CHIMEI INNOLUX
SPEC NO.: A043-24-TT-71
Date : 2010/04/19
4. Touch Screen Panel Specifications
4.1. Electrical Characteristics
Value
Item
Unit
Remark
Min.
Typ.
Max.
-1.5
-
1.5
%
Analog X and Y directions
300
-
1500
Ω
X
100
-
900
Ω
Y
25
-
-
MΩ
Voltage
-
5
7
V
Chattering
-
-
10
ms
100kΩ pull-up
80
-
-
%
JIS K7105
Linearity
Terminal Resistance
Insulation resistance
Transparency
DC 25V
DC
Note: Avoid operating with hard or sharp material such as a ball point pen or a mechanical
pencil except a polyacetal pen (tip R0.8mm or less) or a finger.
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
AZ DISPLAYS
13
ATM0430D5-T(AZ DISPLAYS) TFT MODUL VER1.0
CHIMEI INNOLUX
SPEC NO.: A043-24-TT-71
Date : 2010/04/19
4.2. Mechanical & Reliability Characteristics
Value
Item
Activation force
Durability-surface
scratching
Durability-surface
pitting
Surface hardness
Unit
Remark
Min.
Typ.
Max.
80
-
-
gf
Note 1
Write
100,000
-
-
characters
Note 2
1,000,000
-
-
touches
Note 3
3
-
-
H
JIS K5400
Note 1: Activation force test condition
(1) Input DC 5V on X direction, Drop off Polyacetal Stylus (R0.8), until
output voltage stabilize ,then get the activation force。
(2) R8.0mm Silicon rubber for finger Activation force test
(3) Test point: 9 points
Note 2: Measurement for surface area.
-Scratch 100,000 times straight line on the film with a stylus change every 20,000
times.
-Force: 250gf.
-Speed: 60mm/sec.
-Stylus: R0.8 polyacetal tip.
Note 3: Pit 1,000,000 times on the film with a R0.8 silicon rubber.
-Force: 250gf.
-Speed: 2times/sec.
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
AZ DISPLAYS
14
ATM0430D5-T(AZ DISPLAYS) TFT MODUL VER1.0
CHIMEI INNOLUX
SPEC NO.: A043-24-TT-71
Date : 2010/04/19
4.3. Linearity Definition
Va: maximum voltage in the active area of touch panel
Vb: minimum voltage in the active area of touch panel
X: random measuring point
Vxm: actual voltage of Lx point
Vxi: theoretical voltage of Lx point
Linearity = [|Vxi-Vxm |/(Va-Vb)]*100%
Note: Test area is as follows and operation force is 150gf.
2.0mm
2.0mm
Active Area
Test Area
2.0mm
2.0mm
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
AZ DISPLAYS
15
ATM0430D5-T(AZ DISPLAYS) TFT MODUL VER1.0
CHIMEI INNOLUX
SPEC NO.: A043-24-TT-71
Date : 2010/04/19
4.4. Housing design guide
Housing design follow as below
1) Avoid the design that housing overlap and press on the active area of the LCM
2) Give enough gap(over 0.5mm at compressed) between the housing and TSP
to
protect wrong operating.
3)
Use a buffer material(Gasket) between the TSP and housing to protect
damage and wrong operating
4)
Avoid the design that buffer material overlap and press on the inside of TSP
view area.
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
AZ DISPLAYS
16
ATM0430D5-T(AZ DISPLAYS) TFT MODUL VER1.0
CHIMEI INNOLUX
SPEC NO.: A043-24-TT-71
Date : 2010/04/19
5. Optical Specifications
Values
Item
Viewing angle
(CR≥ 10)
Symbol
Condition
Unit
Min.
Typ.
Max.
θL
Φ=180°(9 o’clock)
60
70
-
θR
Φ=0°(3 o’clock)
60
70
-
Remark
degree
Note 1
Note 7
θT
Φ=90°(12 o’clock)
40
50
-
θB
Φ=270°(6 o’clock)
60
70
-
TON
-
10
20
msec
Note 3
TOFF
-
15
30
msec
Note 3
CR
400
500
-
-
Note 4
0.26
0.31
0.36
-
WY
0.28
0.33
0.38
-
Note 2
Note 5
Note 6
Note 7
Luminance
L
350
400
-
cd/m²
Note 6
Luminance uniformity
YU
70
75
-
%
Note 8
Response time
Contrast ratio
WX
Normal
θ=Φ=0°
Color chromaticity
Test Conditions:
1. VDD=3.3V, IL=20mA (Backlight current), the ambient temperature is 25℃.
2. The test systems refer to Note 2.
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
AZ DISPLAYS
17
ATM0430D5-T(AZ DISPLAYS) TFT MODUL VER1.0
CHIMEI INNOLUX
SPEC NO.: A043-24-TT-71
Date : 2010/04/19
Note 1: Definition of viewing angle range
Normal line
θ=Φ=0°
Φ=90°
12 o’clock direction
θL
θB
θR
θT
Φ=180°
Φ=0°
Active Area
Φ=270°
6 o’clock direction
Fig. 4-1 Definition of viewing angle
Note 2: Definition of optical measurement system.
The optical characteristics should be measured in dark room. After 30 minutes
operation, the optical properties are measured at the center point of the LCD
screen. (Response time is measured by Photo detector TOPCON BM-7, other
items are measured by BM-5A/Field of view: 1° /Height: 500mm.)
Photo detector
500mm
Normal line
θ=Φ=0°
Φ=90°
12 o’clock direction
Φ=0°
Φ=180°
Active Area
Φ=270°
6 o’clock direction
Fig. 4-2 Optical measurement system setup
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
AZ DISPLAYS
18
ATM0430D5-T(AZ DISPLAYS) TFT MODUL VER1.0
CHIMEI INNOLUX
SPEC NO.: A043-24-TT-71
Date : 2010/04/19
Note 3: Definition of Response time
The response time is defined as the LCD optical switching time interval
between “White” state and “Black” state. Rise time (TON) is the time between
photo detector output intensity changed from 90% to 10%. And fall time (TOFF) is
the time between photo detector output intensity changed from 10% to 90%.
Photo detector output
(Relative value)
White (TFT OFF)
Black (TFT ON)
White (TFT OFF)
100%
90%
10%
0%
TON
TOFF
Fig. 4-3 Definition of response time
Note 4: Definition of contrast ratio
Contrast ratio (CR) =
Luminance measured when LCD on the " White" state
Luminance measured when LCD on the " Black" state
Note 5: Definition of color chromaticity (CIE1931)
Color coordinates measured at center point of LCD.
Note 6: All input terminals LCD panel must be ground while measuring the center area of
the panel. The LED driving condition is IL=20mA.
Note 7: The values shall be measured without Touch Screen Panel.
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
AZ DISPLAYS
19
ATM0430D5-T(AZ DISPLAYS) TFT MODUL VER1.0
CHIMEI INNOLUX
SPEC NO.: A043-24-TT-71
Date : 2010/04/19
Note 8: Definition of Luminance Uniformity
Active area is divided into 9 measuring areas (Refer to Fig. 4-4 ).Every
measuring point is placed at the center of each measuring area.
Luminance Uniformity (Yu) =
L-------Active area length
B min
B max
W----- Active area width
L/6
L/3
L/3
W/3
W
W/3
W/6
L
Fig. 4-4 Definition of measuring points
Bmax: The measured maximum luminance of all measurement position.
Bmin: The measured minimum luminance of all measurement position.
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
AZ DISPLAYS
20
ATM0430D5-T(AZ DISPLAYS) TFT MODUL VER1.0
CHIMEI INNOLUX
SPEC NO.: A043-24-TT-71
Date : 2010/04/19
6. Reliability Test Items
(Note3)
Item
Test Conditions
Remark
High Temperature Storage
Ta = 80℃
240 hrs
Note 1,Note 4
Low Temperature Storage
Ta = -30℃
240hrs
Note 1,Note 4
High Temperature Operation
Ts = 70℃
240hrs
Note 2,Note 4
Low Temperature Operation
Ta = -20℃
240hrs
Note 1,Note 4
Operate at High Temperature
and Humidity
+60℃, 90%RH
240 hrs
Note 5
Thermal Shock
-30℃/30 min ~ +80℃/30 min for a total
100 cycles, Start with cold temperature
and end with high temperature
Note 4
Frequency range:10~55Hz
Stroke:1.5mm
Vibration Test
Sweep:10Hz~55Hz~10Hz
2 hours for each direction of X. Y. Z.
(6 hours for total)
100G 6ms,±X, ±Y, ±Z 3 times for each
Mechanical Shock
direction
Random Vibration :
0.015G*G/Hz from 5-200HZ,
Package Vibration Test
-6dB/Octave from 200-500HZ
2 hours for each direction of X. Y. Z.
(6 hours for total)
Height:60 cm
Package Drop Test
1 corner, 3 edges, 6 surfaces
± 2KV, Human Body Mode,
Electro Static Discharge
100pF/1500Ω
Note 1: Ta is the ambient temperature of samples.
Note 2: Ts is the temperature of panel’s surface.
Note 3: In the standard condition, there shall be no practical problem that may affect the
display function. After the reliability test, the product only guarantees operation,
but doesn’t guarantee all the cosmetic specification.
Note 4: Before cosmetic and function tests, the product must have enough recovery
time, at least 2 hours at room temperature.
Note 5: Before cosmetic and function tests, the product must have enough recovery
time, at least 24 hours at room temperature.
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
AZ DISPLAYS
21
ATM0430D5-T(AZ DISPLAYS) TFT MODUL VER1.0
CHIMEI INNOLUX
SPEC NO.: A043-24-TT-71
Date : 2010/04/19
7. General Precautions
7.1. Safety
Liquid crystal is poisonous. Do not put it in your mouth. If liquid crystal touches
your skin or clothes, wash it off immediately by using soap and water.
7.2. Handling
1. The LCD panel is plate glass. Do not subject the panel to mechanical shock or to
excessive force on its surface.
2. The polarizer attached to the display is easily damaged. Please handle it
carefully to avoid scratch or other damages.
3. To avoid contamination on the display surface, do not touch the module surface
with bare hands.
4. Keep a space so that the LCD panels do not touch other components.
5. Put cover board such as acrylic board on the surface of LCD panel to protect
panel from damages.
6. Transparent electrodes may be disconnected if you use the LCD panel under
environmental conditions where the condensation of dew occurs.
7. Do not leave module in direct sunlight to avoid malfunction of the ICs.
7.3. Static Electricity
1. Be sure to ground module before turning on power or operating module.
2. Do not apply voltage which exceeds the absolute maximum rating value.
7.4. Storage
1. Store the module in a dark room where must keep at 25±10℃ and 65%RH or
less.
2. Do not store the module in surroundings containing organic solvent or corrosive
gas.
3. Store the module in an anti-electrostatic container or bag.
7.5. Cleaning
1. Do not wipe the polarizer with dry cloth. It might cause scratch.
2. Only use a soft sloth with IPA to wipe the polarizer, other chemicals might
permanent damage to the polarizer.
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
AZ DISPLAYS
22
ATM0430D5-T(AZ DISPLAYS) TFT MODUL VER1.0
CHIMEI INNOLUX
SPEC NO.: A043-24-TT-71
Date : 2010/04/19
8. Mechanical Drawing
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
AZ DISPLAYS
23
ATM0430D5-T(AZ DISPLAYS) TFT MODUL VER1.0
CHIMEI INNOLUX
SPEC NO.: A043-24-TT-71
Date : 2010/04/19
9. Package Drawing
9.1. Packaging Material Table
No.
Item
1
LCM
Module
2
Partition
3
4
5
Model
(Material)
Corrugated
Bar
Dust-Proof
Bag
Corrugated
ATM0430D5-T
BC Corrugated
paper
BC Corrugated
paper
PE
BC Corrugated
Dimensions
(mm)
Unit
Weight
(kg)
Quantity
(pcs)
105.5 × 67.2 × 4.05
TBD
160
512 × 349 × 106
1.102
2
349 × 173
0.030
8
700 × 530
0.060
1
510 × 343
0.130
2
1152 × 512
0.260
1
Board-1
Paper
Corrugated
BC Corrugated
Board-2
Paper
7
A/S Bag
PE
132 × 117
0.002
160
8
Carton
Co rru ga t e d
pap e r
530 × 355 × 255
1.100
1
9
Total weight
6
Remark
TBD
9.2. Packaging Quantity
(1) LCM quantity per Partition:
2Rows x 40quantity per Row = 80 pcs
(2) Total LCM quantity in Carton: 2 layer x 80 pcs per Partition = 160 pcs
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
AZ DISPLAYS
24
ATM0430D5-T(AZ DISPLAYS) TFT MODUL VER1.0
CHIMEI INNOLUX
SPEC NO.: A043-24-TT-71
Date : 2010/04/19
9.3. Packaging Drawing
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
AZ DISPLAYS
25
Similar pages