EPIGAP ELD-655-533-1 Led - lamp Datasheet

LED - Lamp
ELD-655-533-1
16.11.2007
rev. 05
Radiation
Type
Technology
Case
Red
DDH
AlGaAs/AlGaAs
5 mm plastic lens
Description
High-power, high-speed deep red LED in standard
5 mm package, housing without standoff leads
9 - 0,5
6 - 0,3
1,1 - 0,1
2,54
5,3 - 0,3
0,8 - 0,4
Anode
2 - 1,0
Applications
0,6 - 0,2
32,5
Optical communications, safety equipment,
automation
Maximum Ratings
Tamb = 25°C, unless otherwise specified
Parameter
Test сonditions
Symbol
Value
Unit
IF
30
mA
IFM
100
mA
Operating temperature range
Tamb
-20 to +85
°C
Storage temperature range
Tstg
-55 to +100
°C
Junction temperature
TJ
100
°C
Tsd
260
°C
Typ
Max
Unit
2.0
2.3
V
Forward current (DC)
(tP ≤ 50 µs, tP /T = 1/2)
Peak forward current
t ≤ 5 s, 3 mm from case
Soldering temperature
Optical and Electrical Characteristics
Tamb = 25°C, unless otherwise specified
Test
Parameter
conditions
IF = 20 mA
Forward voltage
Symbol
Min
VF
Reverse voltage
IR = 10 µA
VR
5
Radiant power
IF = 20 mA
Φe
3
4
mW
Luminous intensity
IF = 20 mA
Iv
700
1000
mcd
Radiant intensity
IF = 20 mA
Ie
15
20
mW/sr
Peak wavelength
IF = 20 mA
λp
650
655
Dominant wavelength
IF = 20 mA
λd
640
nm
Spectral bandwidth at 50%
IF = 20 mA
∆λ0.5
22
nm
Viewing angle
IF = 20 mA
ϕ
20
deg.
Switching time
IF = 20 mA
tr, tf
70
ns
V
660
nm
*measured after 30s current flow
Note: All measurements carried out on EPIGAP equipment
We reserve the right to make changes to improve technical design and may do so without further notice.
Parameters can vary in different applications.All operating parameters must be validated for each customer application by the customer.
EPIGAP Optoelektronik GmbH, D-12555 Berlin, Köpenicker Str.325 b, Haus 201
1 of 2
Tel.: +49-30-6576 2543, Fax : +49-30-6576 2545
LED - Lamp
ELD-655-533-1
16.11.2007
rev. 05
Remarks concerning optical radiation safety*
Up to maximum forward current, at continuous operation, this LED may be classified as LED product
Class 1 , according to standard IEC 60825-1:A2. Class 1 products are safe to eyes and skin under
reasonably predictable conditions. This implicates a direct observation of the light beam by means of
optical instruments.
*Note: Safety classification of an optical component mainly depends on the intended application and
the way the component is being used. Furthermore, all statements made to classification are based
on calculations and are only valid for this LED "as it is", and at continuous operation. Using pulsed
current or altering the light beam with additional optics may lead to different safety classifications.
Therefore these remarks should be taken as recommendation and guideline only.
We reserve the right to make changes to improve technical design and may do so without further notice.
Parameters can vary in different applications.All operating parameters must be validated for each customer application by the customer.
EPIGAP Optoelektronik GmbH, D-12555 Berlin, Köpenicker Str.325 b, Haus 201
2 of 2
Tel.: +49-30-6576 2543, Fax : +49-30-6576 2545
Similar pages