Series AM2N-NZ 2 Watt | DC-DC Converter FEATURES: • • • • • • • RoHS compliant 24 Pin DIP Package Low profile plastic package High efficiency up to 82% Operating temperature -40oC to + 85oC Input / Output Isolation 6000VDC Pin compatible with multiple manufacturers Models Single output Model AM2N-0505SH60-NZ AM2N-0509SH60-NZ AM2N-0512SH60-NZ AM2N-0515SH60-NZ AM2N-1205SH60-NZ AM2N-1209SH60-NZ AM2N-1212SH60-NZ AM2N-1215SH60-NZ Input Voltage (V) Output Voltage (V) Output Current max (mA) Isolation (VDC) Efficiency (%) 5 9 12 15 5 9 12 15 400 222 167 133 400 222 167 133 6000 6000 6000 6000 6000 6000 6000 6000 78 79 80 80 79 80 82 82 4.5-5.5 4.5-5.5 4.5-5.5 4.5-5.5 10.8-13.2 10.8-13.2 10.8-13.2 10.8-13.2 Models Dual output Model AM2N-0505DH60-NZ AM2N-0509DH60-NZ AM2N-0512DH60-NZ AM2N-0515DH60-NZ AM2N-1205DH60-NZ AM2N-1209DH60-NZ AM2N-1212DH60-NZ AM2N-1215DH60-NZ Input Voltage (V) Output Voltage (V) 4.5-5.5 4.5-5.5 4.5-5.5 4.5-5.5 10.8-13.2 10.8-13.2 10.8-13.2 10.8-13.2 ±5 ±9 ±12 ±15 ±5 ±9 ±12 ±15 Output Current max (mA) Isolation (VDC) Efficiency (%) 6000 6000 6000 6000 6000 6000 6000 6000 78 79 80 80 79 80 82 82 ±200 ±110 ±84 ±67 ±200 ±110 ±84 ±67 Input Specifications Parameters Voltage range Nominal Typical 5 12 4.5-5.5 10.8-13.2 Filter Maximum Units VDC Capacitor Isolation Specifications Parameters Tested I/O voltage Resistance Conditions Typical 60 sec Rated Units 6000 VDC MOhm >1000 Output Specifications Parameters Voltage accuracy Short Circuit protection Line voltage regulation (Single) Line voltage regulation (Dual) Load voltage regulation (Single) Load voltage regulation (Dual) Temperature coefficient Ripple & Noise www.aimtec.com F 051e R6.D Conditions Typical For 1.0% of Vin For 1.0% of Vin Load 10-100% Load 10-100% At 20MHz Bandwidth Maximum See tolerance graph Momentary (1 sec) ±1.2 ±1.2 15 15 ±0.03 100 Tel: +1 514 620 2722 1 of 3 Units % % % % %/oC mV p-p Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM2N-NZ 2 Watt | DC-DC Converter General Specifications Parameters Switching frequency Operating temperature Storage temperature Max Case temperature Cooling Humidity Case material Weight Dimensions (L x W x H) MTBF Conditions Typical 100% load Without derating 35 Maximum Units 95 KHz o C o C o C 90 % -40 to +85 -55 to +125 Free air convection Plastic UL94-VO 16 g 1.27 x 0.58 x 0.37 inches 32.30 x 14.70 x 9.40 mm >1 000 000 hrs (MIL-HDBK -217F, Ground Benign, t=+25oC) NOTE: All specifications are in this datasheet measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. Safety Specifications Parameters Agency approvals Standards cULus UL60950-1 Pin Out Specifications Pin Dimensions Single 1 2 8,17 10,15 12,13 Dual 32.30 (1.27) Top View +V Input +V Input -V Input -V Input N.C. -V Output -V Output Common +V Output +V Output All other pins No Connection 14.70 (0.58) Footprint 2.54 (0.10) 1.00 0 + 0.15/-0 2.54 (0.01) Side View 9.40 (0.37) 0.65 (0.03) 4.00 (0.16) 2.54 (0.10) 27.94 (1.10) Typical characteristics Tolerance Envelope Graph +10% Typic a +5% line +2.5% -2.5% Output Voltage (%) Nominal Voltage l load -7.5% 10% 50% 100% Output Current (%) www.aimtec.com F 051e R6.D Tel: +1 514 620 2722 2 of 3 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM2N-NZ 2 Watt | DC-DC Converter Filtering single output Filtering dual output External capacitor – Single output External capacitor – Dual output Vin (VDC) External capacitor (uF) Vout (VDC) External capacitor (uF) Vin (VDC) External capacitor (uF) 5 12 24 - 4.7 2.2 1 - 5 9 12 15 10 4.7 2.2 1 5 12 24 - 4.7 2.2 1 - Vout (VDC) 5 9 12 15 External capacitor (uF) 4.7 2.2 1 0.47 NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com. www.aimtec.com F 051e R6.D Tel: +1 514 620 2722 3 of 3 Toll free: + 1 888 9 AIMTEC (924 6832) North America only