DS90CR486 133MHz 48-Bit Channel Link Deserializer (6.384 Gbps) General Description The DS90CR486 receiver converts eight Low Voltage Differential Signaling (LVDS) data streams back into 48 bits of LVCMOS/LVTTL data. Using a 133MHz clock, the data throughput is 6.384Gbit/s (798Mbytes/s). The multiplexing of data lines provides a substantial cable reduction. Long distance parallel single-ended buses typically require a ground wire per active signal (and have very limited noise rejection capability). Thus, for a 48-bit wide data and one clock, up to 98 conductors are required. With this Channel Link chipset as few as 19 conductors (8 data pairs, 1 clock pair and a minimum of one ground) are needed. This provides an 80% reduction in interconnect width, which provides a system cost savings, reduces connector physical size and cost, and reduces shielding requirements due to the cables’ smaller form factor. The DS90CR486 deserializer is improved over prior generations of Channel Link devices and offers higher bandwidth support and longer cable drive with three areas of enhancement. To increase bandwidth, the maximum clock rate is increased to 133 MHz and 8 serialized LVDS outputs are provided. Cable drive is enhanced with a user selectable pre-emphasis (on DS90CR485) feature that provides additional output current during transitions to counteract cable loading effects. Optional DC balancing on a cycle-to-cycle basis, is also provided to reduce ISI (Inter-Symbol Interference). With pre-emphasis and DC balancing, a low distortion eye-pattern is provided at the receiver end of the cable. A cable deskew capability has been added to deskew long cables of pair-to-pair skew. These three enhancements allow long cables to be driven. The DS90CR486 is intended to be used with the DS90CR485 Channel Link Serializer. It is also backward compatible with serializers DS90CR481 and DS90CR483. The DS90CR486 is footprint compatible with the DS90CR484. The chipset is an ideal solution to solve EMI and interconnect size problems for high-throughput point-to-point applications. For more details, please refer to the “Applications Information” section of this datasheet. Features n n n n n n n n n n n Up to 6.384 Gbps throughput 66MHz to 133MHz input clock support Reduces cable and connector size and cost Cable Deskew function DC balance reduces ISI distortion For point-to-point backplane or cable applications Low power, 890 mW typ at 133MHz Flow through pinout for easy PCB design +3.3V supply voltage 100-pin TQFP package Conforms to TIA/EIA-644-A-2001 LVDS Standard Generalized Block Diagram 20025203 © 2003 National Semiconductor Corporation DS200252 www.national.com DS90CR486 133MHz 48-Bit Channel Link Deserializer (6.384 Gbps) March 2003 DS90CR486 133MHz LVDS 48-Bit Channel Link Deserializer Absolute Maximum Ratings Package Derating: (Note 2) ESD Rating: If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage (VCC) LVCMOS/LVTTL Output Voltage 23.8 mW/˚C above +25˚C > 2 kV > 200 V (HBM, 1.5kΩ, 100pF) (EIAJ, 0Ω, 200pF) −0.3V to +3.6V Recommended Operating Conditions −0.3V to (VCC + 0.3V) LVDS Receiver Input Voltage −0.3V to +3.6V Junction Temperature +150˚C Storage Temperature −65˚C to +150˚C Lead Temperature (Soldering, 4 sec.) Nom Max Units 3.14 3.3 3.46 V Operating Free Air Temperature (TA) −10 +25 Receiver Input Range +260˚C +70 ˚C 0 2.4 V 100 mVp-p 66 133 MHz Supply Noise Voltage (VCC) Maximum Package Power Dissipation Capacity @ 25˚C 100 TQFP Package: Min Supply Voltage (VCC) Clock Rate 2.9 W Electrical Characteristics Over recommended operating supply and temperature ranges unless otherwise specified. Symbol Parameter Conditions Min Typ Max Units LVCMOS/LVTTL DC SPECIFICATIONS VIH High Level Input Voltage VIL Low Level Input Voltage IIN Input Current All LVCMOS/LVTTL inputs except PD . 2.0 VCC V For PD input only. 2.5 VCC V GND 0.8 V +15 µA VIN = 0.4V, 2.5V, or VCC (Note 1) +1.8 VIN = GND −15 2.0 VOH High Level Output Voltage IOH = −2 mA VOL Low Level Output Voltage IOL = +2 mA IOS Output Short Circuit Current VOUT = 0V VCL Input Clamp Voltage ICL = −18 mA 0 µA V −0.8 0.4 V −120 mA −1.5 V +100 mV LVDS RECEIVER DC SPECIFICATIONS VTH Differential Input High Threshold VTL Differential Input Low Threshold IIN Input Current VCM = +1.2V −100 mV VIN = +2.4V, VCC = 3.6V VIN = 0V, VCC = 3.6V ± 10 ± 10 µA µA RECEIVER SUPPLY CURRENT ICCRW ICCRZ www.national.com Receiver Supply Current Worst Case CL = 8 pF, BAL = Low, Worst Case Pattern (Figures 1, 2) Receiver Supply Current Power Down PD = Low Receiver Outputs stay low during Power down mode. 2 f = 66 MHz 190 245 mA f = 100 MHz 230 325 mA f = 133 MHz 270 340 mA 60 110 µA Over recommended operating supply and temperature ranges unless otherwise specified. Symbol CLHT CHLT Typ Max Units LVCMOS/LVTTL Low-to-High Transition Time, (Figure 2), Rx data out, (Note 5) Parameter 0.8 1.3 ns LVCMOS/LVTTL Low-to-High Transition Time, (Figure 2), Rx clock out, (Note 5) 0.7 1.0 ns LVCMOS/LVTTL High-to-Low Transition Time, (Figure 2), Rx data out, (Note 5) 0.9 1.3 ns LVCMOS/LVTTL High-to-Low Transition Time, (Figure 2), Rx clock out, (Note 5) 0.8 1.0 ns T 15.152 ns RCOP RxCLK OUT Period, (Figure 3) RCOH RxCLK OUT High Time, (Figure 3) RCOL RSRC RHRC RxCLK OUT Low Time, (Figure 3) RxOUT Data valid before RxCLK OUT, (Figure 3) RxOUT Data valid after RxCLK OUT, (Figure 3) Min 7.518 f = 133 MHz 2.7 ns f = 100 MHz 3.8 ns f = 66 MHz 6.0 ns f = 133 MHz 2.7 ns f = 100 MHz 3.8 ns f = 66 MHz 6.0 f = 133 MHz 2.0 3.5 ns f = 100 MHz 3.0 4.7 ns f = 66 MHz 5.0 7.0 ns f = 133 MHz 2.5 4.1 ns ns f = 100 MHz 3.5 5.0 ns f = 66 MHz 6.0 8.0 ns 2(TCIP)+5 2(TCIP)+10 RPDL Receiver Propagation Delay - Latency, (Figure 4) RPLLS Receiver Phase Lock Loop Set ,(Figure 5) 2(TCIP)+15 ns 10 ms 1 µs RPDD Receiver Powerdown Delay, (Figure 6) RSKMD Receiver Skew Margin with Deskew, BAL=Low (Figure 7), (Note 6) f = 133 MHz 275 ps f = 100 MHz 400 ps f = 66 MHz 500 Receiver Deskew Range f = 133 MHz −150 +150 ps f = 100 MHz −200 +200 ps f = 66 MHz −200 +200 ps RDR ps Note 1: The IIN parameter for the PD pin is not tested at 2.5V. Note 2: “Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the device should be operated at these limits. The tables of “Electrical Characteristics” specify conditions for device operation. Note 3: Typical values are given for VCC = 3.3V and T A = +25˚C. Note 4: Current into device pins is defined as positive. Current out of device pins is defined as negative. Voltages are referenced to ground unless otherwise specified (except VTH, VTL and ∆VID). Note 5: CLHT and CHLT are measurements of the receiver data outputs low-to-high and high-to-low time over the recommended frequency range. The limits are based on bench characterization and Guaranteed By Design (GBD) using statistical analysis. Note 6: Receiver Skew Margin with Deskew (RSKMD) is defined as the valid data sampling region at the receiver inputs. The DESKEW function will constrain the receiver’s sampling strobes to the middle half of the LVDS bit and removes (adjusts for) fixed interconnect skew. This margin (RSKMD) allows for inter-symbol interference (dependent on type/length of cable), Transmitter Pulse Position (TPPOS) variance, and LVDS clock jitter (TJCC). RSKMD ≥ ISI + TPPOS(variance) + LVDS Source Clock Jitter (cycle to cycle). See Applications Information section for more details. 3 www.national.com DS90CR486 133MHz LVDS 48-Bit Channel Link Deserializer Receiver Switching Characteristics DS90CR486 133MHz LVDS 48-Bit Channel Link Deserializer AC Timing Diagrams 20025210 FIGURE 1. “Worst Case” Test Pattern Note 7: The worst case test pattern produces a maximum toggling of digital circuits, LVDS I/O and LVCMOS/LVTTL I/O. 20025213 FIGURE 2. DS90CR486 LVCMOS/LVTTL Output Load and Transition Times 20025216 FIGURE 3. DS90CR486 Setup/Hold and High/Low Times www.national.com 4 DS90CR486 133MHz LVDS 48-Bit Channel Link Deserializer AC Timing Diagrams (Continued) 20025228 FIGURE 4. DS90CR486 Propagation Delay - Latency 20025220 FIGURE 5. DS90CR486 Phase Lock Loop Set Time (VCC > 3.0V) 20025222 FIGURE 6. DS90CR486 Power Down Delay 5 www.national.com DS90CR486 133MHz LVDS 48-Bit Channel Link Deserializer AC Timing Diagrams (Continued) 20025225 C — Setup and Hold Time (Internal data sampling window) defined by Rspos (receiver input strobe position) min and max Tppos — Transmitter output pulse position (min and max) RSKMD = ISI (Inter-symbol interference) + TPPOS(variance) + LVDS Source Clock Jitter (cycle to cycle) Cable Skew — typically 10 ps–40 ps per foot, media dependent Note 8: Refer to transmitter datasheet for Cycle-to-cycle LVDS Output jitter specification. Note 9: ISI is dependent on interconnect length; may be zero. Pre-emphasis in the transimitter is used to reduce the ISI. Refer to transmitter datasheet for more information. FIGURE 7. Receiver Skew Margin with DESKEW (RSKMD) www.national.com 6 DS90CR486 133MHz LVDS 48-Bit Channel Link Deserializer LVDS Interface 20025204 FIGURE 8. 48 LVCMOS/LVTTL Outputs Mapped to 8 LVDS Inputs (DC Balance Mode- Disable, BAL = Low) (E1 - Falling Edge; E2 - Rising Edge) 7 www.national.com DS90CR486 133MHz LVDS 48-Bit Channel Link Deserializer LVDS Interface (Continued) 20025257 FIGURE 9. 48 LVCMOS/LVTTL Outputs Mapped to 8 LVDS Inputs(DC Balance Mode - Enable, BAL = High) (E1 - Falling Edge; E2 - Rising Edge) www.national.com 8 DS90CR486 Receiver Output DS90CR485 Transmitter Input * DS90CR483 Transmitter Input RxOUT0 E2-D0 TxIN0 RxOUT1 E2-D1 TxIN1 RxOUT2 E2-D2 TxIN2 RxOUT3 E2-D3 TxIN3 RxOUT4 E2-D4 TxIN4 RxOUT5 E2-D5 TxIN5 RxOUT6 E2-D6 TxIN6 RxOUT7 E2-D7 TxIN7 RxOUT8 E2-D8 TxIN8 RxOUT9 E2-D9 TxIN9 RxOUT10 E2-D10 TxIN10 RxOUT11 E2-D11 TxIN11 RxOUT12 E2-D12 TxIN12 RxOUT13 E2-D13 TxIN13 RxOUT14 E2-D14 TxIN14 RxOUT15 E2-D15 TxIN15 RxOUT16 E2-D16 TxIN16 RxOUT17 E2-D17 TxIN17 RxOUT18 E2-D18 TxIN18 RxOUT19 E2-D19 TxIN19 RxOUT20 E2-D20 TxIN20 RxOUT21 E2-D21 TxIN21 RxOUT22 E2-D22 TxIN22 RxOUT23 E2-D23 TxIN23 RxOUT24 E1-D0 TxIN24 RxOUT25 E1-D1 TxIN25 RxOUT26 E1-D2 TxIN26 RxOUT27 E1-D3 TxIN27 RxOUT28 E1-D4 TxIN28 RxOUT29 E1-D5 TxIN29 RxOUT30 E1-D6 TxIN30 RxOUT31 E1-D7 TxIN31 RxOUT32 E1-D8 TxIN32 RxOUT33 E1-D9 TxIN33 RxOUT34 E1-D10 TxIN34 RxOUT35 E1-D11 TxIN35 RxOUT36 E1-D12 TxIN36 RxOUT37 E1-D13 TxIN37 RxOUT38 E1-D14 TxIN38 RxOUT39 E1-D15 TxIN39 RxOUT40 E1-D16 TxIN40 RxOUT41 E1-D17 TxIN41 RxOUT42 E1-D18 TxIN42 RxOUT43 E1-D19 TxIN43 RxOUT44 E1-D20 TxIN44 RxOUT45 E1-D21 TxIN45 RxOUT46 E1-D22 TxIN46 RxOUT47 E1-D23 TxIN47 * E1 = Falling Edge and E2 = Rising Edge of RxCLK P/M Input Clock Edge 9 www.national.com DS90CR486 133MHz LVDS 48-Bit Channel Link Deserializer DS90CR486 Outputs Mapped to DS90CR485 Outputs/DS90CR483 Inputs DS90CR486 133MHz LVDS 48-Bit Channel Link Deserializer DS90CR486 Pin Description—Channel Link Receiver Pin Name I/O No. Description RxINP I 8 Positive LVDS differential data inputs. RxINM I 8 Negative LVDS differential data inputs. RxOUT O 48 LVCMOS/LVTTL level data outputs. In PowerDown (PD = Low) mode, receiver outputs are forced to a Low state. RxCLKP I 1 Positive LVDS differential clock input. RxCLKM I 1 Negative LVDS differential clock input. RxCLKOUT O 1 LVCMOS/LVTTL level clock output. The rising edge acts as data strobe. PLLSEL I 1 Control input for PLL range select. This pin must be tied to VCC. No connect or tied to GND is reserved for future use. PD I 1 Power Down pin. This pin must be tied to input level of 2.5V to Vcc for normal operation. When de-asserted (low input) the receiver outputs are Low. Please refer to the Applications Information on the back for more information. DESKEW I 1 This pin must be tied to logic High or Vcc for normal operation of Deskew function. De-asserting a pulse of duration greater than one clock will restart the deskew initialization. Do NOT tie this pin to LOW. Please refer to the Applications Information on the back for more information. BAL I 1 LVCMOS/LVTTL level input. This pin must be tied to logic High or Vcc to enable DC Balance function(Figure 9). When tied low or left open, the DC Balance function is disabled(Figure 8). Please refer to the Applications Information on the back for more infomation. CON1 I 1 Control Pin. This pin must be tied to logic High or Vcc. VCC I 6 Power supply pins for LVCMOS/LVTTL outputs and digital circuitry. GND I 8 Ground pins for LVCMOS/LVTTL outputs and digital circuitry. PLLVCC I 1 Power supply for PLL circuitry. PLLGND I 2 Ground pin for PLL circuitry. LVDSVCC I 2 Power supply pin for LVDS inputs. LVDSGND I 3 Ground pins for LVDS inputs. 6 No Connect. Make NO Connection to these pins - leave open. NC Note 10: These receivers have input fail-safe bias circuitry to guarantee a stable receiver output for floating or terminated receiver inputs. Under these conditions receiver inputs will be in a HIGH state. If a clock signal is present, outputs will all be HIGH; if the cable inter-connects are disconnected which results in floating/terminated inputs, the outputs will remain in the last valid state. A floating/terminated clock input will result in a LOW clock output. www.national.com 10 DC BALANCE In addition to data information an additional bit is transmitted on every LVDS data signal line during each cycle as shown in Figure 9. This bit is the DC balance bit (DCB). The purpose of the DC Balance bit is to minimize the short- and long-term DC bias on the signal lines. This is achieved by selectively sending the data either unmodified or inverted. The value of the DC balance bit is calculated from the running word disparity and the data disparity of the current word to be sent. The data disparity of the current word shall be calculated by subtracting the number of bits of value 0 from the number of bits value 1 in the current word. Initially, the running word disparity may be any value between +7 and −6. The running word disparity shall be calculated as a continuous sum of all the modified data disparity values, where the unmodified data disparity value is the calculated data disparity minus 1 if the data is sent unmodified and 1 plus the inverse of the calculated data disparity if the data is sent inverted. The value of the running word disparity shall saturate at +7 and −6. The value of the DC balance bit (DCB) shall be 0 when the data is sent unmodified and 1 when the data is sent inverted. To determine whether to send data unmodified or inverted, the running word disparity and the current data disparity are used. If the running word disparity is positive and the current data disparity is positive, the data shall be sent inverted. If the running word disparity is positive and the current data disparity is zero or negative, the data shall be sent unmodified. If the running word disparity is negative and the current data disparity is positive, the data shall be sent unmodified. If the running word disparity is negative and the current data disparity is zero or negative, the data shall be sent inverted. If the running word disparity is zero, the data shall be sent inverted. DC Balance mode is set when the BAL pin on the transmitter and receiver are tied HIGH - see pin descriptions. POWER DOWN The receiver provides a power down feature. When deasserted current draw through the supply pins is minimized and the PLLs are shut down. The receiver outputs are forced to an active LOW state when in the power down mode. (See Pin Description Tables). This is not a LVCMOS/LVTTL input pin and has a high input threshold. For normal operation, this pin must be tied to an input level of 2.5V to Vcc. DESKEW The "DESKEW” function on this receiver will deskew or compensate fixed interconnect skew between data signals, with respect to the rising edge of the LVDS clock, on each of the independent differential pairs (pair-to-pair skew). The deskew initialization or calibration is done automatically when the device is powered up. The control pin CON1 must set High and the Deskew pin must set to High on the DS90CR486. However, the Deskew calibration can also be performed after the device is powered up. De-asserting with a pulse of duration greater than one clock cycle to the Deskew pin to restart the calibration of deskew. The calibration takes 4096 clock cycles to complete after the TX and RX PLLs lock (20ms). No RxIN data is sampled during this period. The data outputs during this period will be Low. For normal operation, deskew pin must set to High. Setting the deskew pin to Low or No Connect will continuously recalibrate the sampling strobes. Data outputs are Low during this period. In order for the deskew function to work properly, it must be intialized. The DS90CR486 deskew can be initialized with any data pattern with a transition over a period of three clock cycles. Therefore, there are mulitiple ways to initialize the deskew function depending on the setup configuration (Please refer to Figure 10). For example, to initialize the operation of deskew using DS90CR485 and DS90CR486 in CONFIGURATIONS The chipset is designed to be connected typically to a single receiver load. This is known as a point-to-point configuration. It is also possible to drive multiple receiver loads if certain restrictions are made(i.e. low data rate). Only the final receiver at the end of the interconnect should provide termination across the pair. In this case, the driver still sees the intended DC load of 100 Ohms. Receivers connected to the cable between the transmitter and the final receiver must not load down the signal. To meet this system requirement, stub lengths from the line to the receiver inputs must be kept very short. CABLE TERMINATION A termination resistor is required for proper operation to be obtained. The termination resistor should be equal to the differential impedance of the media being driven. This should be in the range of 90 to 132 Ohms. 100 Ohms is a typical value common used with standard 100 Ohm twisted pair cables. This resistor is required for control of reflections and also to complete the current loop. It should be placed as close to the receiver inputs to minimize the stub length from the resistor to the receiver input pins. 11 www.national.com DS90CR486 133MHz LVDS 48-Bit Channel Link Deserializer DC balance mode, the DS_OPT pin at the input of the transmitter DS90CR485 can be set High OR Low when powered up. The period of this input to the DS_OPT pin must be at least 20ms (TX and RX PLLs lock time) plus 4096 clock cycles in order for the receiver to complete the deskew operation. For other configuration setup with DS90CR483 and DS90CR484, please refer to the flow chart on Figure 10. The DS_OPT pin at the input of the transmitter (DS90CR485) can be used to initiate the deskew calibration pattern. Depends on the configuration, it can be set High or applied Low when power up in order for the receiver to complete the deskew operation. For this reason, the LVDS clock signal with DS_OPT applied high (active data sampling) shall be 1111000 or 1110000 pattern and the LVDS data lines (TxOUT 0-7) shall be High for one clock cycle and Low for the next clock cycle. During the deskew operation with DS_OPT applied low, the LVDS clock signal shall be 1111100 or 1100000 pattern. The transmitter will also output a series of 1111000 or 1110000 onto the LVDS data lines (TxOUT 0-7) during deskew so that the receiver can automatically calibrated the data sampling strobes at the receiver inputs. Each data channel is deskewed independently and is tuned over a specific range. Please refer to corresponding receiver datasheet for a list of deskew ranges. Note that the deskew initialization must be performed at least once after the PLL has locked to the input clock frequency, and it must be done at the time when the receiver is powered up and PLL has locked. If power is lost, or if the cable has been swithcd or disconnected, the initialization procedure must be repeated or else the receiver may not sample the incoming LVDS data correctly. Applications Information DS90CR486 133MHz LVDS 48-Bit Channel Link Deserializer Applications Information has improved over prior generation of Channel Link devices. Additional buffering at the reciver output is not necessary. If high fan-out is required or long transmission line driving capability, buffering the receiver output is recommended. Receiver outputs do not support / provide a TRI-STATE function. (Continued) HOW TO CONFIGURE FOR BACKPLANE APPLICATIONS In a backplane application with differential line impedance of 100Ω the differential line pair-to-pair skew can controlled by trace layout. The transmitter-DS90CR485 “DS_OPT” pin may be set high. In a backplane application with short PCB distance traces, pre-emphasis from the transmitter is typically not required. The “PRE” pin should be left open (do not tie to ground). A resistor pad provision for a pull up resistor to Vcc can be implemented in case pre-emphasis is needed to counteract heavy capacitive loading effects. LVDS INTERCONNECT GUIDELINES See AN-1108 and AN-905 for full details. • • Use the S/2S/3S rule in spacings — S = space between the pair — 2S = space between pairs SUPPLY BYPASS RECOMMENDATIONS — 3S = space to TTL signal Minimize the number of VIA Use differential connectors when operating above 500Mbps line speed • Maintain balance of the traces • Minimize skew within the pair • Minimize skew between pairs • Terminate as close to the RXinputs as possible For more information: Channel Link Applications Notes currently available: • AN-1041 Introduction to Channel Link • AN-1108 PCB and Interconnect Guidelines Bypass capacitors must be used on the power supply pins. Different pins supply different portions of the circuit, therefore capacitors should be nearby all power supply pins except as noted in the pin description table. Use high frequency ceramic (surface mount recommended) 0.1µF capacitors close to each supply pin. If space allows, a 0.01µF capacitor should be used in parallel, with the smallest value closest to the device pin. Additional scattered capacitors over the printed circuit board will improve decoupling. Multiple (large) via should be used to connect the decoupling capacitors to the power plane. A 4.7 to 10µF bulk cap is recommended near the PLLVCC pins and also the LVDSVCC pins. Connections between the caps and the pin should use wide traces. • • • • RECEIVER OUTPUT DRIVE STRENGTH The DS90CR486 output specifies a 8pF load, VOH and VOL are tested at ± 2mA, which is intended for only 1 or maybe 2 loads. The DS90CR486 reciever’s output driving capability www.national.com Use 100Ω coupled differential pairs 12 AN-905 Differential Impedance National’s LVDS Owner’s Manual FIGURE 10. Deskew Configuration Setup Chart CONFIGURATION 1 DS90CR481/483 and DS90CR484 with DC Balance ON (BAL=High, 33MHz to 80MHz) − The DS_OPT pin at the input of the transmitter DS90CR481/483 must be applied low for a minimum of four clock cycles in order for the receiver to complete the deskew operation. The input to the DS_OPT pin can be applied at any time after the PLL has locked to the input clock frequency. In this particular setup, the "DESKEW" pin on the receiver DS90CR484 must set High. a minimum of four clock cycles in order for the receiver to complete the deskew operation. The input to the DS_OPT pin can be applied at any time after the PLL has locked to the input clock frequency. In this setup, the "DESKEW" pin on the receiver DS90CR484 must set High. CONFIGURATION 5 DS90CR485 and DS90CR486 with DC Balance ON (BAL=Hiigh, CON1=High, 66MHz to 133MHz) − The DS_OPT pin at the input of the transmitter DS90CR485 can be set to High OR Low when power up. The period of this input to the DS_OPT pin must be at least 20ms (TX and RX PLLs lock time) plus 4096 clock cycles in order for the receiver to complete the deskew operation. The "DESKEW" and CON1 pins on the receiver DS90CR486 must set High. CONFIGURATION 2 DS90CR481/483 and DS90CR486 with DC Balance ON (BAL=High, CON1=High, 66MHz to 112MHz) − The DS_OPT pin at the input of the transmitter DS90CR481/483 can be set to High OR Low when power up. The period of this input to the DS_OPT pin must be at least 20ms (TX and RX PLLs lock time) plus 4096 clock cycles in order for the receiver to complete the deskew operation. The "DESKEW" and CON1 pins on the receiver DS90CR486 must be tied to High for this setup. CONFIGURATION 6 DS90CR485 and DS90CR486 with DC Balance OFF (BAL=Low, CON1=High, 66MHz to 133MHz) −The input to the DS_OPT pin of the transmitter DS90CR485 in this configuration is completely ignored. In order to initialize the deskew operation on the receiver DS90CR486, data and clcok must be applied to the transimitter when power up. The "DESKEW" and CON1 pins on the receiver DS90CR486 must set High. CONFIGURATION 3 DS90CR481/483 and DS90CR486 with DC Balance OFF (BAL=Low, CON1=High, 66MHz to 112MHz) − The input to the DS_OPT pin of the transmitter DS90CR481/483 in this configuration is completely ignored by the transimitters. In order to initialize the deskew operation on the receiver DS90CR486, data and clcok must be applied to the transimitter when power up. The "DESKEW" and CON1 pins on the receiver DS90CR486 must be tied to High for this setup. DESKEW NOT SUPPORTED Deskew function is NOT supported in these configuration setups. The deskew feature is only supported with DC Balance ON (BAL=High) for DS90CR484. Note that the deskew function in the DS90CR486 works in both DC Balance and NON-DC Balance modes. CONFIGURATION 4 DS90CR485 and DS90CR484 with DC Balance ON (BAL=High, 66MHz to 80MHz) − The DS_OPT pin at the input of the transmitter DS90CR485 must be applied low for Note 11: For more details on Deskew operation, please refer to the "Application Information" section. 13 www.national.com DS90CR486 133MHz LVDS 48-Bit Channel Link Deserializer 20025258 DS90CR486 133MHz LVDS 48-Bit Channel Link Deserializer Pin Diagram Receiver - DS90CR486 (Top View) 20025207 www.national.com 14 DS90CR486 133MHz 48-Bit Channel Link Deserializer (6.384 Gbps) Physical Dimensions inches (millimeters) unless otherwise noted Dimensions show in millimeters Order Number DS90CR486VS NS Package Number VS100A LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Americas Customer Support Center Email: [email protected] Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: [email protected] Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Asia Pacific Customer Support Center Fax: +65-6250 4466 Email: [email protected] Tel: +65-6254 4466 National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: [email protected] Tel: 81-3-5639-7560 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.