Click on Series name for product info on aimtec.com Series AM5T-FZ 5 Watt | DC-DC Converter FEATURES: RoHS compliant 24 Pin DIP Package High efficiency up to 85% Wide 2:1 input range Operating temperature -40oC to + 85oC Input / Output isolation 4000 VACrms Pin compatible with multiple manufacturers OLP, OVP and SCP Models Single Output Model Input Voltage (V) Output Voltage (V) Output Current max (mA) AM5T-1205SH40-FZ AM5T-1212SH40-FZ AM5T-1215SH40-FZ AM5T-2405SH40-FZ AM5T-2412SH40-FZ AM5T-2415SH40-FZ AM5T-4805SH40-FZ AM5T-4812SH40-FZ AM5T-4815SH40-FZ 9 -18 9 -18 9 -18 18 - 36 18 - 36 18 - 36 36 - 75 36 - 75 36 - 75 5 12 15 5 12 15 5 12 15 1000 500 400 1000 500 400 1000 500 400 Model Input Voltage (V) Output Voltage (V) Output Current max (mA) AM5T-1212DH40-FZ AM5T-1215DH40-FZ AM5T-2412DH40-FZ AM5T-2415DH40-FZ AM5T-4812DH40-FZ AM5T-4815DH40-FZ 9 -18 9 -18 18 - 36 18 - 36 36 - 75 36 - 75 ±250 ±200 ±250 ±200 ±250 ±200 Capacitive load, max (μF) Efficiency (%) Isolation (VAC) 81 83 83 82 85 84 81 83 82 4000 4000 4000 4000 4000 4000 4000 4000 4000 Capacitive load, max (μF) Efficiency (%) Isolation (VAC) ±220 ±220 ±220 ±220 ±220 ±220 83 83 84 85 83 83 4000 4000 4000 4000 4000 4000 2000 470 440 2000 470 440 2000 470 440 Models Dual Output ±12 ±15 ±12 ±15 ±12 ±15 Input Specifications Parameters Voltage range Filter Turn on Transient process time (50% load step Change) Transient response over shoot Input reflected ripple current Start up time Absolute Maximum Rating Nominal Typical 12 24 48 9-18 18-36 36-75 Maximum Units VDC Pi Type di/dt=0.8A/µs Vin nominal FL <±5% 12 Vin 24 Vin 48 Vin -0.7-25 -0.7-50 -0.7-100 100 Peak Input Voltage time 780 µs 76 510 % of Vo mA p-p ms VDC ms Isolation Specifications Parameters Rated I/O voltage Tested I/O voltage Resistance Capacitance www.aimtec.com F 051e R11.C Conditions Typical 60 sec 1sec flash test 500VDC > 1000 12 Tel: +1 514 620 2722 1 of 3 Rated Units 4000 6000 VACrms Vpk MOhm pF Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM5T-FZ 5 Watt | DC-DC Converter Output Specifications Parameters Conditions Typical Over load protection Over voltage protection Zener Diode Clamp Voltage accuracy Short circuit protection Short circuit restart Line voltage regulation Load voltage regulation (Single) 25% load to full load Load voltage regulation (Dual) LL to LH at Full Load 25% load to full load Balanced Unbalanced load 25% to 100% full load Temperature coefficient Ripple & Noise (At 20MHz Bandwidth) Maximum 120% 5V model = 6.2V 12V model = 15V 15V model = 18V ±1 Continuous Autorecovery ±0.5 ±0.5 ±0.5 ±3.0 Units of full load Vdc % % % % % %/oC ±0.02 150 70 200 5V output 12V output 15V output mV p-p General Specifications Parameters Switching frequency Operating temperature Storage temperature Max Case temperature Cooling Humidity Case material Weight Dimensions(L x W x H) MTBF Conditions Typical 100% load Full Load (with derating see chart) Maximum Units +95 KHz oC oC oC 150 -40 to +85 -50 to +125 Free air convection 95 % Non-Conductive Plastic 16 g Tolerance ±0.5 mm or ±0.02 inches 1.25 x 0.80 x 0.5 inches 31.7x 20.3 x 12.65 mm >700 000 hrs (MIL-HDBK -217F, Ground Benign, t=+25oC) NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. Pin Out Specifications Dimensions Pin 1 2 10 11 12 13 15 23 24 Single +V Input +V Input N. C. N.C. -V output +Voutput N. C. -V Input -V Input 31.70 (1.25) 12.65 (0.5) Dual +V Input +V Input Common Common N. C. -V output +V output -V Input -V Input 1.88 (0.07) SIDE 0.5 (0.02) 31.70 (1.25) 20.3 (0.8) 2.55 (0.1) 1 2 10 11 12 15.20 (0.6) 15 24 23 2.54 (0.1) 20.32 (1.25) 13 5.08 (0.2) BOTTOM www.aimtec.com F 051e R11.C Tel: +1 514 620 2722 2 of 3 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM5T-FZ 5 Watt | DC-DC Converter Derating NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3.Mechanical drawings and specifications are for reference only. 4.All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. 5.Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com. www.aimtec.com F 051e R11.C Tel: +1 514 620 2722 3 of 3 Toll free: + 1 888 9 AIMTEC (924 6832) North America only