Plastic Film Capacitors DC-Link Film Capacitor Type : TYPE1 Features ● High safety, Self-healing and Self-protecting function built in. catastrophic failure upon natural end of life due to inbuilt fuse function. ● Open circuit failure mode by fuse function patterned electrode ● Can replace Electrolytic Capacitor ● Low ESR, High Ripple Current capability ● Low ESL ● RoHS directive compliant ● No Recommended applications ● Any automotive and/or other application requiring DC Linkage ✽ Verify the usage and fitting environments, and make sure to observe the rated performance specified in the corresponding specifications. Construction ● Dielectric : Polypropylene : Metallized dielectric with Segment pattern ● Plastic Case : PPS. equivalent to UL94 V-0 ● Sealing : Epoxy Resin equivalent to UL94 HB ● Terminal : Copper with Tin plating ● Electrode Explanation of part number 1 2 3 4 5 6 7 8 9 10 11 12 E Z T V K C T Y P 1 H A Specifications Operating temperature on the surface of the case Capacitance – 40 °C to +105 °C including self heat generation % 581 μF +10 −5 % at 1 kHz, 25 ºC Rated voltage 450 V.DC Maximum voltage 600 V.DC for 60 sec in life time Rated ripple current Continuous 80 Arms at 10 kHz Current derating Refer Fig.1 ESR 0.8 mΩ or less at 10KHz ESL Insulation Resistance between Terminals and Case Dimensions L × W × H (Typical data) 20 nH or less at 1MHz 1 GΩ or more Measure after applying 500 +500 V.DC for 2 +20 seconds. 164 × 115 × 43.1 mm : Excluding terminals Weight (Typical data) 980 g Note: 1) Voltage includes ripple voltage 2) Derate the current when the maximum surface temperature exceeds 95 degC, as shown in Fig. 1. Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 01 Feb. 2016 Plastic Film Capacitors Current Derating 100 90 95 °C Ripple current (Arms @ 10k Hz) 80 70 60 50 40 30 20 10 0 −40 60 65 70 75 80 85 90 95 100 105 110 Temperature on the surface of the capacitor housing (°C) Fig.1 Current derating curve Dimensions Unit : mm N f6 .9 + 8±0.3 149±0.4 80 STAMPING AREA (34.5) 4- 33 STAMPING AREA (7.5) P (40) (6.5) 17±0.4 1 43.1±1 164±1 136±1 70±0.4 (51.5) HATCHED AREA : LABEL 22.5 18±1 2-12 6 34.5±0.7 92.5 (20) 0 0 .3 f6 (22) 2- 63.5±0.4 .3 +0 0 .5 85.5±0.4 Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 01 Feb. 2016 Plastic Film Capacitors Characteristics <Reference> <Temperature characteristics (Typical curve)> ● Change ΔC/C 10 ESR (mΩ) at 10 kHz ΔC/C (%) at 1 kHz 10 ● Equivalent of capacitance 5 0 −5 series resistance ESR 0.8 0.6 0.4 0.2 0.0 −10 −40 −20 0 60 20 40 Temperature (°C) 80 100 −40 −20 0 20 40 60 Temperature (°C) 80 100 <Frequency characteristics (Typical curve)> ● Equivalent 1.0 series resistance ESR ESR (mΩ) 0.8 0.6 0.4 0.2 0.0 10 15 20 Frequency (kHz) 25 <Lifetime Expectancy (Reference)> ✽ Expected life : 15,000 hours ✽ Failure in Time : 300 Fits The above values are reference calculated under an pre-assumed average operating condition. Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 01 Feb. 2016