Diodes AH175-PG-A-B Hall effect latch for high temperature Datasheet

AH175
HALL EFFECT LATCH FOR HIGH TEMPERATURE
Description
Pin Assignments
AH175 is a single-digital-output Hall-Effect latch sensor for
high temperature operation. The device includes an on-chip
Hall voltage generator for magnetic sensing, an amplifier to
amplify Hall voltage, and a comparator to provide switching
hysteresis for noise rejection, an open-collector output predriver. An internal band-gap regulator provides a temperature
compensated supply voltage for internal circuits and allows a
wide operating supply range.
(Top View)
3. OUT
2. GND
1. Vcc
SIP-3L
When the magnetic flux density (B) is larger than operate
point (Bop), output is switched on (OUT pin is pulled low).
The output state is held on until a magnetic flux density
reversal falls below Brp. When B is less than Brp, the output
is switched off.
(Top View)
3. OUT
GND 2.
1. Vcc
The AH175 is available in SIP-3L and SC59 packages.
SC59
Features
•
•
•
•
•
•
•
•
Applications
Bipolar Hall-Effect latch sensor
3.5V to 20V DC operating voltage
Open collector pre-driver
25mA output sink current
Built-in power reverse protection
Operating Temperature: -40ºC~+150ºC
SIP-3L and SC59 packages
(SC59 is commonly known as SOT23 in Asia)
Green Molding Compound (No Br, Sb) (Note 1)
Notes:
•
•
•
•
Rotor Position Sensing
Current Switch
Encoder
RPM Detection
1. EU Directive 2002/95/EC (RoHS). All applicable RoHS exemptions applied. Please visit our website at
http://www.diodes.com/products/lead_free.html.
Typical Application Circuit
IA
IB
M
Digital Hall Effect Sensor
IC
Driver
M: Three Phase Hall Motor
Ia
Ib
Ic
&
Control Logic
HA
RPM sensing
HB
HC
Hall Motor Driver
3 Phase Hall Motor
AH175
Document number: DS31043 Rev. 10 - 2
1 of 9
www.diodes.com
July 2010
© Diodes Incorporated
AH175
HALL EFFECT LATCH FOR HIGH TEMPERATURE
Pin Descriptions
Pin Name
Pin #
Description
Vcc
1
Positive Power Supply
GND
2
Ground
OUT
3
Output Stage
Functional Block Diagram
VCC
1
REG.
3 OUT
AMP
2 GND
Absolute Maximum Ratings (TA = 25°C)
Symbol
VCC
VOUT (off)
IO (sink)
Ts
TJ
PD
Characteristics
Supply Voltage
Output “Off” Voltage
Output “On” Current
Storage Temperature Range
Maximum Junction Temperature
SIP-3L
SC59
Power Dissipation
Values
20
20
25
-65~+150
+150
550
230
Unit
V
V
mA
°C
°C
mW
mW
Recommended Operating Conditions
Symbol
VCC
TA
Notes:
Characteristic
Supply Voltage
Operating Ambient Temperature
(Note 2)
Conditions
Min
Max
Unit
Operating
3.5
20
V
Operating
-40
150
°C
2. The device PD and Safety Operation Area should not be exceeded.
AH175
Document number: DS31043 Rev. 10 - 2
2 of 9
www.diodes.com
July 2010
© Diodes Incorporated
AH175
HALL EFFECT LATCH FOR HIGH TEMPERATURE
Electrical Characteristics (TA = 25°C)
Symbol
VOUT (SAT)
ICC
Characteristics
Conditions
Min
Typ.
Max
Unit
Output Saturation Voltage
VCC = 12V, OUT ”ON”
IO = 10mA
-
300
400
mV
Supply Current
VCC = 12V, OUT ”OFF”
-
3.5
6
mA
Magnetic Characteristics (TA = 25°C, Vcc = 12V, unless otherwise specified, Note 3)
(1mT = 10 Gauss)
A grade
Symbol
Bops(south pole to brand side)
Brps(south pole to brand side)
Bhy(|Bopx|-|Brpx|)
Parameter
Operation Point
Release Point
Hysteresis
Min
15
-60
30
Typ.
80
Max
60
-15
120
Unit
Gauss
Gauss
Gauss
Parameter
Operation Point
Release Point
Hysteresis
Min
5
-80
10
Typ.
80
Max
80
-5
160
Unit
Gauss
Gauss
Gauss
B grade
Symbol
Bops(south pole to brand side)
Brps(south pole to brand side)
Bhy(|Bopx|-|Brpx|)
Notes:
3. Magnetic characteristics may vary with supply voltage, operating temperature and after soldering.
Operating Characteristics
S
S
Marking side
Marking side
(Output Voltage)
Vout
Vcc
Vd
High
Bhy
Low
N
N
(SC59)
(SIP-3L)
VSAT
Brp
0
Bop
(Magnetic Flux Density)
AH175
Document number: DS31043 Rev. 10 - 2
3 of 9
www.diodes.com
July 2010
© Diodes Incorporated
AH175
HALL EFFECT LATCH FOR HIGH TEMPERATURE
Performance Characteristics
(1) SIP-3L
TA (°C)
PD (mW)
TA (°C)
PD(mW)
25
550
105
198
50
440
110
176
P D (m W )
60
396
115
154
70
352
120
132
80
308
125
110
85
286
130
88
90
264
135
66
95
242
140
44
100
220
150
0
P o w e r D is s ip a tio n C u rve
600
500
400
300
200
100
0
00
-4
25
50
75
100
125
150
T A (°C )
(2) SC59 (commonly known as SOT23 in Asia)
TA (°C)
25
50
60
70
80
85
90
100
110
120
130
140
150
PD (mW)
230
184
166
147
129
120
110
92
74
55
37
18
0
P D (m W )
P o w e r D is s ip a tio n C u rv e
300
200
100
0
-400
25
50
75
100
125
150
T A (°C )
AH175
Document number: DS31043 Rev. 10 - 2
4 of 9
www.diodes.com
July 2010
© Diodes Incorporated
AH175
HALL EFFECT LATCH FOR HIGH TEMPERATURE
Ordering Information
AH175 - X X - X - X
Package
P : SIP-3L
W : SC59
Device
Magnetic
Characteristics
Packing
Lead Free
L : Lead Free
G : Green (Note 4)
Tube/Bulk
Package Packaging
Part
Code (Note 5, 6) Quantity Number
Suffix
A or B
A : Ammo Box (Note 7)
B : Bulk (Note 8)
7 : Tape & Reel
7” Tape and Reel
Ammo Box
Quantity
Part
Number
Suffix
Quantity
Part
Number
Suffix
Magnetic
Characteristics
AH175-PL-A-A
P
SIP-3L
NA
NA
NA
NA
4000/Box
-A
A
AH175-PL-A-B
P
SIP-3L
NA
NA
NA
NA
4000/Box
-A
B
AH175-PG-A-A
P
SIP-3L
NA
NA
NA
NA
4000/Box
-A
A
AH175-PG-A-B
P
SIP-3L
NA
NA
NA
NA
4000/Box
-A
B
AH175-PL-B-A
P
SIP-3L
1000
-B
NA
NA
NA
NA
A
AH175-PL-B-B
P
SIP-3L
1000
-B
NA
NA
NA
NA
B
AH175-PG-B-A
P
SIP-3L
1000
-B
NA
NA
NA
NA
A
AH175-PG-B-B
P
SIP-3L
1000
-B
NA
NA
NA
NA
B
AH175-WL-7-A
W
SC59
NA
NA
3000/Tape & Reel
-7
NA
NA
A
AH175-WL-7-B
W
SC59
NA
NA
3000/Tape & Reel
-7
NA
NA
B
AH175-WG-7-A
W
SC59
NA
NA
3000/Tape & Reel
-7
NA
NA
A
AH175-WG-7-B
W
SC59
NA
NA
3000/Tape & Reel
-7
NA
NA
B
Notes:
4. EU Directive 2002/95/EC (RoHS). All applicable RoHS exemptions applied. Please visit our website at
http://www.diodes.com/products/lead_free.html.
5. Pad layout as shown on Diodes Inc. suggested pad layout document AP02001, which can be found on our website at
http://www.diodes.com/datasheets/ap02001.pdf.
6. Reverse taping as shown on Diodes Inc. Surface Mount (SMD) Packaging document AP02007, which can be found on our
website http://www.diodes.com/datasheets/ap02007.pdf.
7. Ammo Box is for SIP-3L Spread Lead.
8. Bulk is for SIP-3L Straight Lead.
AH175
Document number: DS31043 Rev. 10 - 2
5 of 9
www.diodes.com
July 2010
© Diodes Incorporated
AH175
HALL EFFECT LATCH FOR HIGH TEMPERATURE
Marking Information
(1) SIP-3L
(Top View)
Y : Year : 0~9
WW : Week : 01~52, "52" represents
52 and 53 week
X : Internal Code : A~Z : Green
a~z : Lead Free
175
Part Number
Y WW X
(2) SC59 (Commonly known as SOT23 in Asia)
(Top View)
XX Y W X
Part Number
AH175
AH175
Document number: DS31043 Rev. 10 - 2
XX : Identification code
Y : Year 0~9
W : Week : A~Z : 1~26 week;
a~z : 27~52 week; z represents
52 and 53 week
X : A~Z : Green
a~z : Lead Free
Package
SC59
6 of 9
www.diodes.com
Identification Code
J5
July 2010
© Diodes Incorporated
AH175
HALL EFFECT LATCH FOR HIGH TEMPERATURE
Package Outline Dimensions (All Dimensions in mm)
(1) Package Type: SIP-3L for Bulk pack
0.51mm
NOM
2.00 +/0.10mm
1.15 +/0.10mm
BRANDED
SURFACE
1
Active Area Depth
2
3
Sensor Location
Package Dimension
AH175
Document number: DS31043 Rev. 10 - 2
7 of 9
www.diodes.com
July 2010
© Diodes Incorporated
AH175
HALL EFFECT LATCH FOR HIGH TEMPERATURE
Package Outline Dimensions (Continued)
(2) Package Type: SIP-3L for Ammo pack
(3) SC59 (Commonly known as SOT23 in Asia)
TOP VIEW
1.50/
1.70
0.35/0.50
2.70/
3.00
1.90
2.90/3.10
1.00/
1.30
0.10/0.20
0.013/0.10
0.95
0.35/0.55
0 O /8 O
AH175
Document number: DS31043 Rev. 10 - 2
8 of 9
www.diodes.com
July 2010
© Diodes Incorporated
AH175
HALL EFFECT LATCH FOR HIGH TEMPERATURE
IMPORTANT NOTICE
DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS
DOCUMENT, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION).
Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other
changes without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability
arising out of the application or use of this document or any product described herein; neither does Diodes Incorporated convey any
license under its patent or trademark rights, nor the rights of others. Any Customer or user of this document or products described
herein in such applications shall assume all risks of such use and will agree to hold Diodes Incorporated and all the companies
whose products are represented on Diodes Incorporated website, harmless against all damages.
Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized
sales channel.
Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall
indemnify and hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized application.
Products described herein may be covered by one or more United States, international or foreign patents pending. Product names
and markings noted herein may also be covered by one or more United States, international or foreign trademarks.
LIFE SUPPORT
Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without
the express written approval of the Chief Executive Officer of Diodes Incorporated. As used herein:
A. Life support devices or systems are devices or systems which:
1. are intended to implant into the body, or
2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided
in the labeling can be reasonably expected to result in significant injury to the user.
B.
A critical component is any component in a life support device or system whose failure to perform can be reasonably expected
to cause the failure of the life support device or to affect its safety or effectiveness.
Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or
systems, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements
concerning their products and any use of Diodes Incorporated products in such safety-critical, life support devices or systems,
notwithstanding any devices- or systems-related information or support that may be provided by Diodes Incorporated. Further,
Customers must fully indemnify Diodes Incorporated and its representatives against any damages arising out of the use of Diodes
Incorporated products in such safety-critical, life support devices or systems.
Copyright © 2010, Diodes Incorporated
www.diodes.com
AH175
Document number: DS31043 Rev. 10 - 2
9 of 9
www.diodes.com
July 2010
© Diodes Incorporated
Similar pages