AMIC A25L05PMF-50UF 8 mbit, low voltage, serial flash memory with 50 mhz spi bus interface Datasheet

A25L80P
Preliminary
8 Mbit, Low Voltage, Serial Flash Memory
With 50 MHz SPI Bus Interface
Document Title
8 Mbit, Low Voltage, Serial Flash Memory With 50MHz SPI Bus Interface
Revision History
Rev. No.
0.0
PRELIMINARY
History
Issue Date
Initial issue
May 30, 2005
(May, 2005, Version 0.0)
Remark
AMIC Technology Corp.
A25L80P
8 Mbit, Low Voltage, Serial Flash Memory
With 50 MHz SPI Bus Interface
Preliminary
FEATURES
GENERAL DESCRIPTION
8 Mbit of Flash Memory
Flexible Sector Architecture (4/4/8/16/32)KB/64x15 KB
Bulk Erase (8 Mbit) in 10s (typical)
Sector Erase (512 Kbit) in 1s (typical)
Page Program (up to 256 Bytes) in 3ms (typical)
2.7 to 3.6V Single Supply Voltage
SPI Bus Compatible Serial Interface
50MHz Clock Rate (maximum)
Deep Power-down Mode 1µA (typical)
Electronic Signature
- JEDEC Standard (13h)
The A25L80P is an 8 Mbit (1M x 8) Serial Flash Memory, with
advanced write protection mechanisms, accessed by a high
speed SPI-compatible bus.
The memory can be programmed 1 to 256 bytes at a time,
using the Page Program instruction.
The memory is organized as 16 sectors, each containing 256
pages. Each page is 256 bytes wide. Thus, the whole memory
can be viewed as consisting of 4096 pages, or 1,048,576
bytes.
The whole memory can be erased using the Bulk Erase
instruction, or a sector at a time, using the Sector Erase
instruction.
Pin Configurations
SO8 Connections
SO16 Connections
A25L80P
HOLD
VCC
DU
DU
DU
DU
S
Q
A25L80P
S
Q
W
VSS
1
2
3
4
8 VCC
7 HOLD
6 C
5 D
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
C
D
DU
DU
DU
DU
VSS
W
Note:
DU = Do not Use
PRELIMINARY
(May 2005, Version 0.0)
1
AMIC Technology Corp.
A25L80P
Block Diagram
HOLD
W
High Voltage
Generator
Control Logic
S
C
D
I/C Shift Register
Q
Address register
and Counter
256 Byte
Data Buffer
Status
Register
FFFFFh
Y Decoder
Size of the
read-only
memory area
000FFh
00000h
256 Byte (Page Size)
X Decoder
Pin Descriptions
Pin No.
Logic Symbol
Description
C
Serial Clock
D
Serial Data Input
Q
Serial Data Output
S
Chip Select
W
Write Protect
HOLD
Hold
Vcc
Supply Voltage
Vss
Ground
PRELIMINARY
(May 2005, Version 0.0)
VCC
D
Q
C
S
A25L80P
W
HOLD
VSS
2
AMIC Technology Corp.
A25L80P
SIGNAL DESCRIPTION
Serial Data Output (Q). This output signal is used to transfer
data serially out of the device. Data is shifted out on the falling
edge of Serial Clock (C).
Serial Data Input (D). This input signal is used to transfer data
serially into the device. It receives instructions, addresses, and
the data to be programmed. Values are latched on the rising
edge of Serial Clock (C).
Serial Clock (C). This input signal provides the timing of the
serial interface. Instructions, addresses, or data present at
Serial Data Input (D) are latched on the rising edge of Serial
Clock (C). Data on Serial Data Output (Q) changes after the
falling edge of Serial Clock (C).
Chip Select ( S ). When this input signal is High, the device is
deselected and Serial Data Output (Q) is at high impedance.
Unless an internal Program, Erase or Write Status Register
cycle is in progress, the device will be in the Standby mode
(this is not the Deep Power-down mode). Driving Chip Select
( S ) Low enables the device, placing it in the active power
mode.
After Power-up, a falling edge on Chip Select ( S ) is required
prior to the start of any instruction.
Hold ( HOLD ). The Hold ( HOLD ) signal is used to pause any
serial communications with the device without deselecting the
device.
During the Hold condition, the Serial Data Output (Q) is high
impedance, and Serial Data Input (D) and Serial Clock (C) are
Don’t Care. To start the Hold condition, the device must be
selected, with Chip Select ( S ) driven Low.
Write Protect ( W ). The main purpose of this input signal is to
freeze the size of the area of memory that is protected against
program or erase instructions (as specified by the values in the
BP2, BP1 and BP0 bits of the Status Register).
SPI MODES
edge of Serial Clock (C).
The difference between the two modes, as shown in Figure 2,
is the clock polarity when the bus master is in Stand-by mode
and not transferring data:
– C remains at 0 for (CPOL=0, CPHA=0)
– C remains at 1 for (CPOL=1, CPHA=1)
These devices can be driven by a microcontroller with its SPI
peripheral running in either of the two following modes:
– CPOL=0, CPHA=0
– CPOL=1, CPHA=1
For these two modes, input data is latched in on the rising edge
of Serial Clock (C), and output data is available from the falling
PRELIMINARY
(May 2005, Version 0.0)
3
AMIC Technology Corp.
A25L80P
Figure 1. Bus Master and Memory Devices on the SPI Bus
SPI Interface with
(CPOL, CPHA)
= (0, 0) or (1, 1)
SDO
SDI
SCK
C Q D
C Q D
C Q D
Bus Master
(ST6, ST7, ST9,
ST10, Other)
CS3
CS2
SPI Memory
Device
SPI Memory
Device
SPI Memory
Device
S
S
S
CS1
W HOLD
W HOLD
W HOLD
Note: The Write Protect ( W ) and Hold ( HOLD ) signals should be driven, High or Low as appropriate.
Figure 2. SPI Modes Supported
CPOL
CPHA
0
0
C
1
1
C
D
MSB
Q
PRELIMINARY
(May 2005, Version 0.0)
MSB
4
AMIC Technology Corp.
A25L80P
OPERATING FEATURES
Page Programming
Status Register
To program one data byte, two instructions are required: Write
Enable (WREN), which is one byte, and a Page Program (PP)
sequence, which consists of four bytes plus data. This is
followed by the internal Program cycle (of duration tPP).
To spread this overhead, the Page Program (PP) instruction
allows up to 256 bytes to be programmed at a time (changing
bits from 1 to 0), provided that they lie in consecutive
addresses on the same page of memory.
The Status Register contains a number of status and control
bits that can be read or set (as appropriate) by specific
instructions.
WIP bit. The Write In Progress (WIP) bit indicates whether the
memory is busy with a Write Status Register, Program or Erase
cycle.
WEL bit. The Write Enable Latch (WEL) bit indicates the status
of the internal Write Enable Latch, BP2, BP1, and BP0 bits.
The Block Protect (BP2, BP1, BP0) bits are non-volatile. They
define the size of the area to be software protected against
Program and Erase instructions.
SRWD bit. The Status Register Write Disable (SRWD) bit is
operated in conjunction with the Write Protect ( W ) signal. The
Status Register Write Disable (SRWD) bit and Write Protect
( W ) signal allow the device to be put in the Hardware
Protected mode. In this mode, the non-volatile bits of the
Status Register (SRWD, BP2, BP1, BP0) become read-only
bits.
Sector Erase and Bulk Erase
The Page Program (PP) instruction allows bits to be reset from
1 to 0. Before this can be applied, the bytes of memory need to
have been erased to all 1s (FFh). This can be achieved, a
sector at a time, using the Sector Erase (SE) instruction, or
throughout the entire memory, using the Bulk Erase (BE)
instruction. This starts an internal Erase cycle (of duration tSE or
tBE).
The Erase instruction must be preceded by a Write Enable
(WREN) instruction.
Protection Modes
Polling During a Write, Program or Erase Cycle
The environments where non-volatile memory devices are
used can be very noisy. No SPI device can operate correctly in
the presence of excessive noise. To help combat this, the
A25L80P boasts the following data protection mechanisms:
Power-On Reset and an internal timer (tPUW) can provide
protection against inadvertant changes while the power
supply is outside the operating specification.
Program, Erase and Write Status Register instructions are
checked that they consist of a number of clock pulses that
is a multiple of eight, before they are accepted for
execution.
All instructions that modify data must be preceded by a
Write Enable (WREN) instruction to set the Write Enable
Latch (WEL) bit. This bit is returned to its reset state by the
following events:
- Power-up
- Write Disable (WRDI) instruction completion
- Write Status Register (WRSR) instruction completion
- Page Program (PP) instruction completion
- Sector Erase (SE) instruction completion
- Bulk Erase (BE) instruction completion
The Block Protect (BP2, BP1, BP0) bits allow part of the
memory to be configured as read-only. This is the Software
Protected Mode (SPM).
The Write Protect ( W ) signal allows the Block Protect (BP2,
BP1, BP0) bits and Status Register Write Disable (SRWD)
bit to be protected. This is the Hardware Protected Mode
(HPM).
In addition to the low power consumption feature, the Deep
Power-down mode offers extra software protection from
inadvertant Write, Program and Erase instructions, as all
instructions are ignored except one particular instruction
(the Release from Deep Power-down instruction).
A further improvement in the time to Write Status Register
(WRSR), Program (PP) or Erase (SE or BE) can be achieved
by not waiting for the worst case delay (tW, tPP, tSE, or tBE). The
Write In Progress (WIP) bit is provided in the Status Register
so that the application program can monitor its value, polling it
to establish when the previous Write cycle, Program cycle or
Erase cycle is complete.
Active Power, Stand-by Power and Deep
Power-Down Modes
When Chip Select ( S ) is Low, the device is enabled, and in the
Active Power mode.
When Chip Select ( S ) is High, the device is disabled, but could
remain in the Active Power mode until all internal cycles have
completed (Program, Erase, Write Status Register). The device
then goes in to the Stand-by Power mode. The device
consumption drops to ICC1.
The Deep Power-down mode is entered when the specific
instruction (the Enter Deep Power-down Mode (DP) instruction)
is executed. The device consumption drops further to ICC2. The
device remains in this mode until another specific instruction
(the Release from Deep Power-down Mode and Read
Electronic Signature (RES) instruction) is executed.
All other instructions are ignored while the device is in the
Deep Power-down mode. This can be used as an extra
software protection mechanism, when the device is not in
active use, to protect the device from inadvertent Write,
Program or Erase instructions.
PRELIMINARY
(May 2005, Version 0.0)
5
AMIC Technology Corp.
A25L80P
Table 1. Protected Area Sizes
Status Register Content
BP2 Bit
BP1 Bit
Memory Content
BP0 Bit
Protected Area
Unprotected Area
1
0
0
0
none
All sectors (sixteen sectors: 0 to 15)
0
0
1
Upper sixteenth (sector 15)
Lower fifteen-eighths (fifteen sectors: 0 to 14)
0
1
0
Upper eighth (two sectors: 14 and 15)
Lower seven-eights (fourteen sectors: 0 to 13)
0
1
1
Upper quarter (four sectors: 12 to 15)
Lower three-quarters (twelve sectors: 0 to 11)
1
0
0
Upper half (eight sectors: 8 to 15)
Lower half (eight sectors: 0 to 7)
1
0
1
All sectors (eight sectors: 0 to 15)
none
1
1
0
All sectors (eight sectors: 0 to 15)
none
1
1
1
All sectors (eight sectors: 0 to 15)
none
Note: 1. The device is ready to accept a Bulk Erase instruction if, and only if, all Block Protect (BP2, BP1, BP0) are 0.
Hold Condition
(C) next goes Low. This is shown in Figure 3.
During the Hold condition, the Serial Data Output (Q) is high
impedance, and Serial Data Input (D) and Serial Clock (C) are
Don’t Care.
Normally, the device is kept selected, with Chip Select ( S )
driven Low, for the whole duration of the Hold condition. This is
to ensure that the state of the internal logic remains unchanged
from the moment of entering the Hold condition.
If Chip Select ( S ) goes High while the device is in the Hold
condition, this has the effect of resetting the internal logic of the
device. To restart communication with the device, it is
necessary to drive Hold ( HOLD ) High, and then to drive Chip
The Hold ( HOLD ) signal is used to pause any serial
communications with the device without resetting the clocking
sequence. However, taking this signal Low does not terminate
any Write Status Register, Program or Erase cycle that is
currently in progress.
To enter the Hold condition, the device must be selected, with
Chip Select ( S ) Low.
The Hold condition starts on the falling edge of the Hold
( HOLD ) signal, provided that this coincides with Serial Clock
(C) being Low (as shown in Figure 3.).
The Hold condition ends on the rising edge of the Hold ( HOLD )
signal, provided that this coincides with Serial Clock (C) being
Low.
If the falling edge does not coincide with Serial Clock (C) being
Low, the Hold condition starts after Serial Clock (C) next goes
Low. Similarly, if the rising edge does not coincide with Serial
Clock (C) being Low, the Hold condition ends after Serial Clock
Select ( S ) Low. This prevents the device from going back to
the Hold condition.
Figure 3. Hold Condition Activation
C
HOLD
Hold
Condition
(standard use)
PRELIMINARY
(May 2005, Version 0.0)
6
Hold
Condition
(non-standard use)
AMIC Technology Corp.
A25L80P
MEMORY ORGANIZATION
The memory is organized as:
1,048,576 bytes (8 bits each)
16 sectors (one (4/4/8/16/32) Kbytes & 64x15 Kbytes each)
4096 pages (256 bytes each).
Each page can be individually programmed (bits are
programmed from 1 to 0). The device is Sector or Bulk
Erasable (bits are erased from 0 to 1) but not Page Erasable.
Table 2. Memory Organization
Sector
Sector Size (Kbytes)
15
64
F0000h
FFFFFh
14
64
E0000h
EFFFFh
13
64
D0000h
DFFFFh
12
64
C0000h
CFFFFh
11
64
B0000h
BFFFFh
10
64
A0000h
AFFFFh
9
64
90000h
9FFFFh
8
64
80000h
8FFFFh
7
64
70000h
7FFFFh
6
64
60000h
6FFFFh
5
64
50000h
5FFFFh
4
64
40000h
4FFFFh
3
64
30000h
3FFFFh
2
64
20000h
2FFFFh
1
64
10000h
1FFFFh
0-4
32
08000h
0FFFFh
0-3
16
04000h
07FFFh
0-2
8
02000h
03FFFh
0-1
4
01000h
01FFFh
0-0
4
00000h
00FFFh
PRELIMINARY
(May 2005, Version 0.0)
Address Range
7
AMIC Technology Corp.
A25L80P
INSTRUCTIONS
sequence is being shifted out.
In the case of a Page Program (PP), Sector Erase (SE), Bulk
Erase (BE), Write Status Register (WRSR), Write Enable
(WREN), Write Disable (WRDI) or Deep Power-down (DP)
instruction, Chip Select ( S ) must be driven High exactly at a
byte boundary, otherwise the instruction is rejected, and is not
executed. That is, Chip Select ( S ) must driven High when the
All instructions, addresses and data are shifted in and out of
the device, most significant bit first.
Serial Data Input (D) is sampled on the first rising edge of
Serial Clock (C) after Chip Select ( S ) is driven Low. Then, the
one-byte instruction code must be shifted in to the device, most
significant bit first, on Serial Data Input (D), each bit being
latched on the rising edges of Serial Clock (C).
The instruction set is listed in Table 3.
Every instruction sequence starts with a one-byte instruction
code. Depending on the instruction, this might be followed by
address bytes, or by data bytes, or by both or none.
In the case of a Read Data Bytes (READ), Read Data Bytes at
Higher Speed (Fast_Read), Read Status Register (RDSR) or
Release from Deep Power-down, Read Device Identification
and Read Electronic Signature (RES) instruction, the shifted-in
instruction sequence is followed by a data-out sequence. Chip
Select ( S ) can be driven High after any bit of the data-out
number of clock pulses after Chip Select ( S ) being driven Low
is an exact multiple of eight.
All attempts to access the memory array during a Write Status
Register cycle, Program cycle or Erase cycle are ignored, and
the internal Write Status Register cycle, Program cycle or
Erase cycle continues unaffected.
Table 3. Instruction Set
Instruction
Description
One-byte Instruction Code
Address
Bytes
Dummy
Bytes
Data Bytes
WREN
Write Enable
0000 0110
06h
0
0
0
WRDI
Write Disable
0000 0100
04h
0
0
0
RDSR
Read Status Register
0000 0101
05h
0
0
1 to ∞
WRSR
Write Status Register
0000 0001
01h
0
0
1
READ
Read Data Bytes
0000 0011
03h
3
0
1 to ∞
Read Data Bytes at Higher Speed
0000 1011
0Bh
3
1
1 to ∞
PP
Page Program
0000 0010
02h
3
0
1 to 256
SE
Sector Erase
1101 1000
D8h
3
0
0
BE
Bulk Erase
1100 0111
C7h
0
0
0
DP
Deep Power-down
1011 1001
B9h
0
0
0
RDID
Read Device Identification
1001 1111
9Fh
0
0
1 to 3
RES
Release from Deep Power-down,
and Read Electronic Signature
1010 1011
ABh
0
3
1 to ∞
0
0
0
FAST_READ
Release from Deep Power-down
PRELIMINARY
(May 2005, Version 0.0)
8
AMIC Technology Corp.
A25L80P
Write Enable (WREN)
The Write Enable (WREN) instruction (Figure 4.) sets the Write
Enable Latch (WEL) bit.
The Write Enable Latch (WEL) bit must be set prior to every
Page Program (PP), Sector Erase (SE), Bulk Erase (BE) and
Write Status Register (WRSR) instruction.
The Write Enable (WREN) instruction is entered by driving
Chip Select ( S ) Low, sending the instruction code, and then
driving Chip Select ( S ) High.
Figure 4. Write Enable (WREN) Instruction Sequence
S
0
1
2 3
4 5
6
7
C
Instruction
D
Q
High Impedance
Write Disable (WRDI)
﹣ Power-up
The Write Disable (WRDI) instruction (Figure 5.) resets the
Write Enable Latch (WEL) bit.
The Write Disable (WRDI) instruction is entered by driving Chip
﹣
﹣
﹣
﹣
﹣
Select ( S ) Low, sending the instruction code, and then driving
Chip The Write Enable Latch (WEL) bit is reset under the
following conditions:
Write Disable (WRDI) instruction completion
Write Status Register (WRSR) instruction completion
Page Program (PP) instruction completion
Sector Erase (SE) instruction completion
Bulk Erase (BE) instruction completion
Figure 5. Write Disable (WRDI) Instruction Sequence
S
0
1
2 3
4 5
6
7
C
Instruction
D
Q
PRELIMINARY
(May 2005, Version 0.0)
High Impedance
9
AMIC Technology Corp.
A25L80P
Read Status Register (RDSR)
The Read Status Register (RDSR) instruction allows the Status
Register to be read. The Status Register may be read at any
time, even while a Program, Erase or Write Status Register
cycle is in progress. When one of these cycles is in progress, it
is recommended to check the Write In Progress (WIP) bit
before sending a new instruction to the device. It is also
possible to read the Status Register continuously, as shown in
Figure 6.
0 no such cycle is in progress.
WEL bit. The Write Enable Latch (WEL) bit indicates the status
of the internal Write Enable Latch. When set to 1 the internal
Write Enable Latch is set, when set to 0 the internal Write
Enable Latch is reset and no Write Status Register, Program or
Erase instruction is accepted.
BP2, BP1, BP0 bits. The Block Protect (BP2, BP1, BP0) bits
are non-volatile. They define the size of the area to be software
protected against Program and Erase instructions. These bits
are written with the Write Status Register (WRSR) instruction.
When one or both of the Block Protect (BP2, BP1, BP0) bits is
set to 1, the relevant memory area (as defined in Table 1.)
becomes protected against Page Program (PP) and Sector
Erase (SE) instructions. The Block Protect (BP2, BP1, BP0)
bits can be written provided that the Hardware Protected mode
has not been set. The Bulk Erase (BE) instruction is executed if,
and only if, both Block Protect (BP2, BP1, BP0) bits are 0.
Table 4. Status Register Format
b7
SRWD
0
0
BP2
BP1
BP0
WEL
b0
WIP
Status Register
Write Protect
Block Protect Bits
SRWD bit. The Status Register Write Disable (SRWD) bit is
operated in conjunction with the Write Protect ( W ) signal. The
Status Register Write Disable (SRWD) bit and Write Protect
( W ) signal allow the device to be put in the Hardware
Protected mode (when the Status Register Write Disable
(SRWD) bit is set to 1, and Write Protect ( W ) is driven Low).
In this mode, the non-volatile bits of the Status Register
(SRWD, BP2, BP1, BP0) become read-only bits and the Write
Status Register (WRSR) instruction is no longer accepted for
execution.
Write Enable Latch Bit
Write In Progress Bit
The status and control bits of the Status Register are as
follows:
WIP bit. The Write In Progress (WIP) bit indicates whether the
memory is busy with a Write Status Register, Program or Erase
cycle. When set to 1, such a cycle is in progress, when reset to
Figure 6. Read Status Register (RDSR) Instruction Sequence and Data-Out Sequence
S
0
1
2 3 4
5 6
7 8
9 10 11 12 13 14 15
C
Instruction
D
Status Register Out
Status Register Out
Q
PRELIMINARY
High Impedance
(May 2005, Version 0.0)
7 6 5
MSB
4
10
3 2 1
0
7 6
MSB
5
4
3
2 1
0
7
AMIC Technology Corp.
A25L80P
Write Status Register (WRSR)
The Write Status Register (WRSR) instruction allows new
values to be written to the Status Register. Before it can be
accepted, a Write Enable (WREN) instruction must previously
have been executed. After the Write Enable (WREN)
instruction has been decoded and executed, the device sets
the Write Enable Latch (WEL).
The Write Status Register (WRSR) instruction is entered by
Register cycle is in progress, the Status Register may still be
read to check the value of the Write In Progress (WIP) bit. The
Write In Progress (WIP) bit is 1 during the self-timed Write
Status Register cycle, and is 0 when it is completed. When the
cycle is completed, the Write Enable Latch (WEL) is reset.
The Write Status Register (WRSR) instruction allows the user
to change the values of the Block Protect (BP2, BP1, BP0) bits,
to define the size of the area that is to be treated as read-only,
as defined in Table 1. The Write Status Register (WRSR)
instruction also allows the user to set or reset the Status
Register Write Disable (SRWD) bit in accordance with the
Write Protect ( W ) signal. The Status Register Write Disable
(SRWD) bit and Write Protect ( W ) signal allow the device to
be put in the Hardware Protected Mode (HPM). The Write
Status Register (WRSR) instruction is not executed once the
Hardware Protected Mode (HPM) is entered.
driving Chip Select ( S ) Low, followed by the instruction code
and the data byte on Serial Data Input (D).
The instruction sequence is shown in Figure 7. The Write
Status Register (WRSR) instruction has no effect on b6, b5, b1
and b0 of the Status Register. b6 and b5 are always read as 0.
Chip Select ( S ) must be driven High after the eighth bit of the
data byte has been latched in. If not, the Write Status Register
(WRSR) instruction is not executed. As soon as Chip Select ( S )
is driven High, the self-timed Write Status Register cycle
(whose duration is tW) is initiated. While the Write Status
Figure 7. Write Status Register (WRSR) Instruction Sequence
S
0
1
2 3 4
5 6
7 8
9 10 11 12 13 14 15
C
Status
Register In
Instruction
7
D
Q
PRELIMINARY
(May 2005, Version 0.0)
6 5
4
3 2 1
0
MSB
High Impedance
11
AMIC Technology Corp.
A25L80P
Table 5. Protection Modes
Signal
SRWD
Bit
1
0
W
0
0
1
1
0
1
Mode
Memory Content
Write Protection of the
Status Register
Protected Area1
Unprotected Area1
Software
Protected
(SPM)
Status Register is Writable (if the
WREN instruction has set the
WEL bit) The values in the
SRWD, BP2, BP1 and BP0 bits
can be changed
Protected against Page
Program, Sector Erase and
Bulk Erase
Ready to accept Page
Program and Sector Erase
instructions
Hardware
Protected
(HPM)
Status Register is Hardware write
protected The values in the
SRWD, BP2, BP1 and BP0 bits
cannot be changed
Protected against Page
Program, Sector Erase and
Bulk Erase
Ready to accept Page
Program and Sector Erase
instructions
Note: 1. As defined by the values in the Block Protect (BP2, BP1, BP0) bits of the Status Register, as shown in Table 1.
consequence, all the data bytes in the memory area that
are software protected (SPM) by the Block Protect (BP2,
BP1, BP0) bits of the Status Register, are also hardware
protected against data modification.
Regardless of the order of the two events, the Hardware
Protected Mode (HPM) can be entered:
The protection features of the device are summarized in Table 5.
When the Status Register Write Disable (SRWD) bit of the
Status Register is 0 (its initial delivery state), it is possible to
write to the Status Register provided that the Write Enable
Latch (WEL) bit has previously been set by a Write Enable
(WREN) instruction, regardless of the whether Write Protect
( W ) is driven High or Low.
When the Status Register Write Disable (SRWD) bit of the
Status Register is set to 1, two cases need to be considered,
depending on the state of Write Protect ( W ):
­ If Write Protect ( W ) is driven High, it is possible to write to
the Status Register provided that the Write Enable Latch
(WEL) bit has previously been set by a Write Enable
(WREN) instruction.
­ If Write Protect (W) is driven Low, it is not possible to write
to the Status Register even if the Write Enable Latch (WEL)
bit has previously been set by a Write Enable (WREN)
instruction. (Attempts to write to the Status Register are
rejected, and are not accepted for execution). As a
PRELIMINARY
(May 2005, Version 0.0)
by setting the Status Register Write Disable (SRWD) bit
after driving Write Protect ( W ) Low
­ or by driving Write Protect ( W ) Low after setting the Status
Register Write Disable (SRWD) bit.
The only way to exit the Hardware Protected Mode (HPM) once
entered is to pull Write Protect ( W ) High.
­
If Write Protect ( W ) is permanently tied High, the Hardware
Protected Mode (HPM) can never be activated, and only the
Software Protected Mode (SPM), using the Block Protect (BP2,
BP1, BP0) bits of the Status Register, can be used.
12
AMIC Technology Corp.
A25L80P
Read Data Bytes (READ)
single Read Data Bytes (READ) instruction. When the highest
address is reached, the address counter rolls over to 000000h,
allowing the read sequence to be continued indefinitely.
The Read Data Bytes (READ) instruction is terminated by
The device is first selected by driving Chip Select ( S ) Low. The
instruction code for the Read Data Bytes (READ) instruction is
followed by a 3-byte address (A23-A0), each bit being
latched-in during the rising edge of Serial Clock (C). Then the
memory contents, at that address, is shifted out on Serial Data
Output (Q), each bit being shifted out, at a maximum frequency
fR, during the falling edge of Serial Clock (C).
The instruction sequence is shown in Figure 8. The first byte
addressed can be at any location. The address is automatically
incremented to the next higher address after each byte of data
is shifted out. The whole memory can, therefore, be read with a
driving Chip Select ( S ) High. Chip Select ( S ) can be driven
High at any time during data output. Any Read Data Bytes
(READ) instruction, while an Erase, Program or Write cycle is
in progress, is rejected without having any effects on the cycle
that is in progress.
Figure 8. Read Data Bytes (READ) Instruction Sequence and Data-Out Sequence
S
0
1
2 3 4
5 6
7 8
9 10
28 29 30 31 32 33 34 35 36 37 38 39
C
Instruction
24-Bit Address
23 22 21
D
3
2
1
0
MSB
Q
Data Out 2
Data Out 1
High Impedance
7 6
5
4
3
2
1
0
7
MSB
PRELIMINARY
(May 2005, Version 0.0)
13
AMIC Technology Corp.
A25L80P
Read Data Bytes at Higher Speed (FAST_READ)
instruction. When the highest address is reached, the address
counter rolls over to 000000h, allowing the read sequence to
be continued indefinitely.
The Read Data Bytes at Higher Speed (FAST_READ)
The device is first selected by driving Chip Select ( S ) Low. The
instruction code for the Read Data Bytes at Higher Speed
(FAST_READ) instruction is followed by a 3-byte address
(A23-A0) and a dummy byte, each bit being latched-in during
the rising edge of Serial Clock (C). Then the memory contents,
at that address, is shifted out on Serial Data Output (Q), each
bit being shifted out, at a maximum frequency fC, during the
falling edge of Serial Clock (C).
The instruction sequence is shown in Figure 9. The first byte
addressed can be at any location. The address is automatically
incremented to the next higher address after each byte of data
is shifted out. The whole memory can, therefore, be read with a
single Read Data Bytes at Higher Speed (FAST_READ)
instruction is terminated by driving Chip Select ( S ) High. Chip
Select ( S ) can be driven High at any time during data output.
Any Read Data Bytes at Higher Speed (FAST_READ) instruction, while an Erase, Program or Write cycle is in progress,
is rejected without having any effects on the cycle that is in
progress.
Figure 9. Read Data Bytes at Higher Speed (FAST_READ) Instruction Sequence and Data-Out Sequence
S
0
1
2 3 4
5 6
7 8
9 10
28 29 30 31
C
Instruction
24-Bit Address
23 22 21
D
2
3
1
0
MSB
High Impedance
Q
S
32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47
C
Dummy Byte
D
7 6
5
4
3
2 1
0
Data Out 2
Data Out 1
7 6
Q
5
4
3
MSB
2
1
0
7 6
MSB
5
4
3
2
1
0
7
MSB
Note: Address bits A23 to A20 are Don’t Care.
PRELIMINARY
(May 2005, Version 0.0)
14
AMIC Technology Corp.
A25L80P
Page Program (PP)
The Page Program (PP) instruction allows bytes to be
programmed in the memory (changing bits from 1 to 0). Before
it can be accepted, a Write Enable (WREN) instruction must
previously have been executed. After the Write Enable (WREN)
instruction has been decoded, the device sets the Write Enable
Latch (WEL).
programmed correctly within the same page. If less than 256
Data bytes are sent to device, they are correctly programmed
at the requested addresses without having any effects on the
other bytes of the same page.
Chip Select ( S ) must be driven High after the eighth bit of the
last data byte has been latched in, otherwise the Page
Program (PP) instruction is not executed.
The Page Program (PP) instruction is entered by driving Chip
Select ( S ) Low, followed by the instruction code, three address
bytes and at least one data byte on Serial Data Input (D). If the
8 least significant address bits (A7-A0) are not all zero, all
transmitted data that goes beyond the end of the current page
are programmed from the start address of the same page (from
the address whose 8 least significant bits (A7-A0) are all zero).
As soon as Chip Select ( S ) is driven High, the self-timed Page
Program cycle (whose duration is tPP) is initiated. While the
Page Program cycle is in progress, the Status Register may be
read to check the value of the Write In Progress (WIP) bit. The
Write In Progress (WIP) bit is 1 during the self-timed Page
Program cycle, and is 0 when it is completed. At some
unspecified time before the cycle is completed, the Write
Enable Latch (WEL) bit is reset.
Chip Select ( S ) must be driven Low for the entire duration of
the sequence.
The instruction sequence is shown in Figure 10. If more than
256 bytes are sent to the device, previously latched data are
discarded and the last 256 data bytes are guaranteed to be
A Page Program (PP) instruction applied to a page which is
protected by the Block Protect (BP2, BP1, BP0) bits (see Table
2 and Table 1) is not executed.
Figure 10. Page Program (PP) Instruction Sequence
S
0
1
2 3 4
5 6
7 8
9 10
28 29 30 31 32 33 34 35 36 37 38 39
C
Instruction
Data Byte 1
24-Bit Address
23 22 21
3
2
1
MSB
0
5
7 6
4
3
0
1
2
2078
2079
2077
2076
2075
40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55
2074
S
2073
MSB
2072
D
1
0
C
Data Byte 2
D
7 6
5
4
3
MSB
2
Data Byte 3
1
0
7 6
5
4
3
MSB
2
Data Byte 256
1
0
7 6
5
4
3
2
MSB
Note: Address bits A23 to A20 are Don’t Care.
PRELIMINARY
(May 2005, Version 0.0)
15
AMIC Technology Corp.
A25L80P
Sector Erase (SE)
The Sector Erase (SE) instruction sets all bits to 1 (FFh).
Before it can be accepted, a Write Enable (WREN) instruction
must previously have been executed. After the Write Enable
(WREN) instruction has been decoded, the device sets the
Write Enable Latch (WEL).
The Sector Erase (SE) instruction is entered by driving Chip
instruction is not executed. As soon as Chip Select ( S ) is
driven High, the self-timed Sector Erase cycle (whose duration
is tBE) is initiated. While the Sector Erase cycle is in progress,
the Status Register may be read to check the value of the Write
In Progress (WIP) bit. The Write In Progress (WIP) bit is 1
during the self-timed Sector Erase cycle, and is 0 when it is
completed. At some unspecified time before the cycle is
completed, the Write Enable Latch (WEL) bit is reset.
The Sector Erase (SE) instruction is executed only if all
Block Protect (BP2, BP1, BP0) bits are 0. The Sector Erase
(SE) instruction is ignored if one, or more, sectors are
protected.
Select ( S ) Low, followed by the instruction code on Serial Data
Input (D). Chip Select ( S ) must be driven Low for the entire
duration of the sequence.
The instruction sequence is shown in Figure 11. Chip Select
( S ) must be driven High after the eighth bit of the instruction
code has been latched in, otherwise the Sector Erase
Figure 11. Sector Erase (SE) Instruction Sequence
S
0
1
2 3 4
5 6
7 8
9 10
28 29 30 31
C
Instruction
24-Bit Address
23 22 21
D
3
2
1
0
MSB
Notes: Address bits A23 to A20 are Don’t Care.
PRELIMINARY
(May 2005, Version 0.0)
16
AMIC Technology Corp.
A25L80P
Bulk Erase (BE)
The Bulk Erase (BE) instruction sets all bits to 1 (FFh). Before
it can be accepted, a Write Enable (WREN) instruction must
previously have been executed. After the Write Enable (WREN)
instruction has been decoded, the device sets the Write Enable
Latch (WEL).
The Bulk Erase (BE) instruction is entered by driving Chip
is not executed. As soon as Chip Select ( S ) is driven High, the
self-timed Bulk Erase cycle (whose duration is tBE) is initiated.
While the Bulk Erase cycle is in progress, the Status Register
may be read to check the value of the Write In Progress (WIP)
bit. The Write In Progress (WIP) bit is 1 during the self-timed
Bulk Erase cycle, and is 0 when it is completed. At some
unspecified time before the cycle is completed, the Write
Enable Latch (WEL) bit is reset.
The Bulk Erase (BE) instruction is executed only if all Block
Protect (BP2, BP1, BP0) bits are 0. The Bulk Erase (BE)
instruction is ignored if one, or more, sectors are protected.
Select ( S ) Low, followed by the instruction code on Serial Data
Input (D). Chip Select ( S ) must be driven Low for the entire
duration of the sequence.
The instruction sequence is shown in Figure 12. Chip Select
( S ) must be driven High after the eighth bit of the instruction
code has been latched in, otherwise the Bulk Erase instruction
Figure 12. Bulk Erase (BE) Instruction Sequence
S
0
1
2
3
4 5
6
7
C
Instruction
D
Notes: Address bits A23 to A20 are Don’t Care.
PRELIMINARY
(May 2005, Version 0.0)
17
AMIC Technology Corp.
A25L80P
Deep Power-down (DP)
Executing the Deep Power-down (DP) instruction is the only
way to put the device in the lowest consumption mode (the
Deep Power-down mode). It can also be used as an extra
software protection mechanism, while the device is not in
active use, since in this mode, the device ignores all Write,
Program and Erase instructions.
The Deep Power-down mode automatically stops at
Power-down, and the device always Powers-up in the Standby
mode.
The Deep Power-down (DP) instruction is entered by driving
Chip Select ( S ) Low, followed by the instruction code on Serial
Data Input (D). Chip Select ( S ) must be driven Low for the
entire duration of the sequence. The instruction sequence is
shown in Figure 13.
Driving Chip Select ( S ) High deselects the device, and puts
the device in the Standby mode (if there is no internal cycle
currently in progress). But this mode is not the Deep
Power-down mode. The Deep Power-down mode can only be
entered by executing the Deep Power-down (DP) instruction, to
reduce the standby current (from ICC1 to ICC2, as specified in DC
Characteristics Table.).
Chip Select ( S ) must be driven High after the eighth bit of the
instruction code has been latched in, otherwise the Deep
Power-down (DP) instruction is not executed. As soon as Chip
Select ( S ) is driven High, it requires a delay of tDP before the
supply current is reduced to ICC2 and the Deep Power-down
mode is entered.
Any Deep Power-down (DP) instruction, while an Erase,
Program or Write cycle is in progress, is rejected without
having any effects on the cycle that is in progress.
Once the device has entered the Deep Power-down mode, all
instructions are ignored except the Release from Deep
Power-down and Read Electronic Signature (RES) instruction.
This releases the device from this mode. The Release from
Deep Power-down and Read Electronic Signature (RES)
instruction also allows the Electronic Signature of the device to
be output on Serial Data Output (Q).
Figure 13. Deep Power-down (DP) Instruction Sequence
S
0
1
2
3
4 5
6
tDP
7
C
Instruction
D
Stand-by Mode
PRELIMINARY
(May 2005, Version 0.0)
18
Deep Power-down Mode
AMIC Technology Corp.
A25L80P
Read Device Identification (RDID)
The Read Identification (RDID) instruction allows the 8-bit
manufacturer identification code to be read, followed by two
bytes of device identification. The manufacturer identification is
assigned by JEDEC, and has the value 37h, plus the
continuation identification for AMIC Technology. The device
identification is assigned by the device manufacturer, and
indicates the memory in the first bytes (02h), and the memory
capacity of the device in the second byte (13h).
This is followed by the 32-bit device identification, stored in the
memory, being shifted out on Serial Data Output (Q), each bit
being shifted out during the falling edge of Serial Clock (C).
The instruction sequence is shown in Figure 14. The Read
Identification (RDID) instruction is terminated by driving Chip
Select ( S ) High at any time during data output.
When Chip Select ( S ) is driven High, the device is put in the
Stand-by Power mode. Once in the Stand-by Power mode, the
device waits to be selected, so that it can receive, decode and
execute instructions.
Any Read Identification (RDID) instruction while an Erase, or
Program cycle is in progress, is not decoded, and has no effect
on the cycle that is in progress.
The device is first selected by driving Chip Select ( S ) Low.
Then, the 8-bit instruction code for the instruction is shifted in.
Table. Read Identification (READ_ID) Data-Out Sequence
Manufacture Identification
Device Identification
Continuation ID
Manufacture ID
Memory Type
Memory Capacity
7Fh
37h
02h
13h
Figure 14. Read Identification (RDID) Data-Out Sequence
S
0 1
2
3
4
5
6
7
8
9 10
13 14 15 16 17 18
21 22 23 24 25 26
29 30 31 32 33 34
37 38 39
C
Instruction
D
Q
31
High Impedance
PRELIMINARY
(May 2005, Version 0.0)
30 29
26
25 24 23
Continuation ID
22 21
18
17 16 15 14 13
Manufacture ID
19
10
9
8
Memory Type
7
6
5
2
1
0
Device ID
AMIC Technology Corp.
A25L80P
latched-in on Serial Data Input (D) during the rising edge of
Serial Clock (C). Then, the 8-bit Electronic Signature, stored in
the memory, is shifted out on Serial Data Output (Q), each bit
being shifted out during the falling edge of Serial Clock (C).
The instruction sequence is shown in Figure 15.
The Release from Deep Power-down and Read Electronic
Signature (RES) instruction is terminated by driving Chip Select
Release from Deep Power-down and Read Electronic
Signature (RES)
Once the device has entered the Deep Power-down mode, all
instructions are ignored except the Release from Deep
Power-down and Read Electronic Signature (RES) instruction.
Executing this instruction takes the device out of the Deep
Power-down mode.
( S ) High after the Electronic Signature has been read at least
once. Sending additional clock cycles on Serial Clock (C), while
The instruction can also be used to read, on Serial Data Output
(Q), the 8-bit Electronic Signature, whose value for the
A25L80P is 13h.
Chip Select ( S ) is driven Low, cause the Electronic Signature
to be output repeatedly.
Except while an Erase, Program or Write Status Register cycle
is in progress, the Release from Deep Power-down and Read
Electronic Signature (RES) instruction always provides access
to the 8-bit Electronic Signature of the device, and can be
applied even if the Deep Power-down mode has not been
entered.
When Chip Select ( S ) is driven High, the device is put in the
Stand-by Power mode. If the device was not previously in the
Deep Power-down mode, the transition to the Stand-by Power
mode is immediate. If the device was previously in the Deep
Power-down mode, though, the transition to the Standby Power
Any Release from Deep Power-down and Read Electronic
Signature (RES) instruction while an Erase, Program or Write
Status Register cycle is in progress, is not decoded, and has
no effect on the cycle that is in progress.
mode is delayed by tRES2, and Chip Select ( S ) must remain
High for at least tRES2 (max), as specified in AC Characteristics
Table . Once in the Stand-by Power mode, the device waits to
be selected, so that it can receive, decode and execute instructions.
The device is first selected by driving Chip Select ( S ) Low. The
instruction code is followed by 3 dummy bytes, each bit being
Figure 15. Release from Deep Power-down and Read Electronic Signature (RES) Instruction Sequence and
Data-Out Sequence
S
0
1
2 3 4
5 6
7 8
9 10
28 29 30 31 32 33 34 35 36 37 38
C
Instruction
23 22 21
D
tRES2
3 Dummy Butes
3
2
1
0
MSB
Q
High Impedance
7 6
5
4
3
2
1
0
MSB
Deep Power-down Mode
Stand-by Mode
Note: The value of the 8-bit Electronic Signature, for the A25L80P, is 13h.
PRELIMINARY
(May 2005, Version 0.0)
20
AMIC Technology Corp.
A25L80P
Figure 16. Release from Deep Power-down (RES) Instruction Sequence
S
C
D
Q
0
1
2
3
4 5
6
tRES1
7
Instruction
High Impedance
Deep Power-down Mode
Power-down mode, though, the transition to the Stand-by
Driving Chip Select ( S ) High after the 8-bit instruction byte has
been received by the device, but before the whole of the 8-bit
Electronic Signature has been transmitted for the first time (as
shown in Figure 16.), still insures that the device is put into
Stand-by Power mode. If the device was not previously in the
Deep Power-down mode, the transition to the Stand-by Power
mode is immediate. If the device was previously in the Deep
PRELIMINARY
(May 2005, Version 0.0)
Stand-by Mode
Power mode is delayed by tRES1, and Chip Select ( S ) must
remain High for at least tRES1 (max), as specified in AC
Characteristics Table. Once in the Stand-by Power mode, the
device waits to be selected, so that it can receive, decode and
execute instructions.
21
AMIC Technology Corp.
A25L80P
POWER-UP AND POWER-DOWN
­ tPUW after VCC passed the VWI threshold
- tVSL afterVCC passed the VCC(min) level
These values are specified in Table 6.
If the delay, tVSL, has elapsed, after VCC has risen above
VCC(min), the device can be selected for READ instructions
even if the tPUW delay is not yet fully elapsed.
At Power-up, the device is in the following state:
At Power-up and Power-down, the device must not be selected
(that is Chip Select ( S ) must follow the voltage applied on VCC)
until VCC reaches the correct value:
­
­
VCC (min) at Power-up, and then for a further delay of tVSL
VSS at Power-down
Usually a simple pull-up resistor on Chip Select ( S ) can be
used to insure safe and proper Power-up and Power-down.
To avoid data corruption and inadvertent write operations
during power up, a Power On Reset (POR) circuit is included.
The logic inside the device is held reset while VCC is less than
the POR threshold value, VWI – all operations are disabled, and
the device does not respond to any instruction.
Moreover, the device ignores all Write Enable (WREN), Page
Program (PP), Sector Erase (SE), Bulk Erase (BE) and Write
Status Register (WRSR) instructions until a time delay of tPUW
has elapsed after the moment that VCC rises above the VWI
threshold. However, the correct operation of the device is not
guaranteed if, by this time, VCC is still below VCC(min). No Write
Status Register, Program or Erase instructions should be sent
until the later of:
The device is in the Standby mode (not the Deep
Power-down mode).
­ The Write Enable Latch (WEL) bit is reset.
Normal precautions must be taken for supply rail decoupling, to
stabilize the VCC feed. Each device in a system should have the
VCC rail decoupled by a suitable capacitor close to the package
pins. (Generally, this capacitor is of the order of 0.1µF).
At Power-down, when VCC drops from the operating voltage, to
below the POR threshold value, VWI, all operations are disabled
and the device does not respond to any instruction. (The
designer needs to be aware that if a Power-down occurs while
a Write, Program or Erase cycle is in progress, some data
corruption can result.)
­
Figure 17-1. Power-up Timing
VCC
VCC(max)
VCC(min)
tPU
Full Device Access
time
PRELIMINARY
(May 2005, Version 0.0)
22
AMIC Technology Corp.
A25L80P
Figure 17-2. Power-Down and Voltage Drop
VCC
VCC(max)
No Device Access Allowed
VCC(min)
tPU
Device Access Allowed
VCC(low)
tPD
time
Table 6. Power-Up Timing and VWI Threshold
Symbol
Parameter
Min.
Max.
Unit
tVSL1
VCC(min) to S low
10
tPUW1
Time delay to Write instruction
1
10
ms
VWI1
Write Inhibit Voltage
1
2
V
µs
Note: 1. These parameters are characterized only.
INITIAL DELIVERY STATE
The device is delivered with the memory array erased: all bits are set to 1 (each byte contains FFh). The Status Register contains
00h (all Status Register bits are 0).
PRELIMINARY
(May 2005, Version 0.0)
23
AMIC Technology Corp.
A25L80P
Absolute Maximum Ratings*
*Comments
Storage Temperature (TSTG) . . . . . . . . . . . . . -65°C to + 150°C
Lead Temperature during Soldering (Note 1)
Input and Output Voltage (with respect to Ground) (VID) . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.6V to +4.0V
Supply Voltage (VCC) . . . . . . . . . . . . . . . . . . . . . -0.6V to +4.0V
Electrostatic Discharge Voltage (Human Body model) (VESD)
(Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . -2000V to 2000V
Stressing the device above the rating listed in the Absolute
Maximum Ratings" table may cause permanent damage to the
device. These are stress ratings only and operation of the
device at these or any other conditions above those indicated in
the Operating sections of this specification is not implied.
Exposure to Absolute Maximum Rating conditions for extended
periods may affect device reliability. Refer also to the AMIC
SURE Program and other relevant quality documents.
Notes:
1. Compliant with JEDEC Std J-STD-020B (for small body,
Sn-Pb or Pb assembly).
2. JEDEC Std JESD22-A114A (C1=100 pF, R1=1500Ω, R2=500
Ω)
DC AND AC PARAMETERS
This section summarizes the operating and measurement
conditions, and the DC and AC characteristics of the device.
The parameters in the DC and AC Characteristic tables that
follow are derived from tests performed under the
Measurement Conditions summarized in the relevant tables.
Designers should check that the operating conditions in their
circuit match the measurement conditions when relying on the
quoted parameters.
Table 7. Operating Conditions
Symbol
Parameter
Min.
Max.
Unit
VCC
Supply Voltage
2.7
3.6
V
TA
Ambient Operating Temperature
–40
85
°C
Table 8. Data Retention and Endurance
Parameter
Condition
Min.
Max.
Unit
Erase/Program Cycles
At 85°C
100,000
Cycles per sector
Data Retention
At 85°C
20
Years
Note: 1. This is preliminary data
Table 9. Capacitance
Symbol
Parameter
Test Condition
Min.
Max.
Unit
COUT
Output Capacitance (Q)
VOUT = 0V
8
pF
CIN
Input Capacitance (other pins)
VIN = 0V
6
pF
Note: Sampled only, not 100% tested, at TA=25°C and a frequency of 33 MHz.
PRELIMINARY
(May 2005, Version 0.0)
24
AMIC Technology Corp.
A25L80P
Table 10. DC Characteristics
Symbol
Parameter
Test Condition
Min.
Max.
Unit
ILI
Input Leakage Current
±2
µA
ILO
Output Leakage Current
±2
µA
ICC1
Standby Current
50
µA
ICC2
Deep Power-down Current
S = VCC, VIN = VSS or VCC
S = VCC, VIN = VSS or VCC
10
µA
ICC3
Operating Current (READ)
C= 0.1VCC / 0.9.VCC at 50MHz, Q = open
8
mA
C= 0.1VCC / 0.9.VCC at 33MHz, Q = open
4
mA
ICC4
Operating Current (PP)
15
mA
ICC5
Operating Current (WRSR)
S = VCC
S = VCC
15
mA
ICC6
Operating Current (SE)
15
mA
ICC7
Operating Current (BE)
S = VCC
S = VCC
15
mA
VIL
Input Low Voltage
–0.5
0.3VCC
V
VIH
Input High Voltage
0.7VCC
VCC+0.4
V
VOL
Output Low Voltage
IOL = 1.6mA
0.4
V
VOH
Output High Voltage
IOH = –100µA
VCC–0.2
V
Note: 1. This is preliminary data at 85°C
Table 11. Instruction Times
Symbol
Alt.
Parameter
tW
Write Status Register Cycle Time
tPP
Page Program Cycle Time
tSE
Sector Erase Cycle Time
tBE
Bulk Erase Cycle Time
Min.
Typ.
Max.
Unit
5
15
ms
1.5
5
ms
1
3
s
4.5
10
s
Note: 1. At 85°C
2. This is preliminary data
Table 12. AC Measurement Conditions
Symbol
CL
Parameter
Min.
Load Capacitance
Max.
30
Input Rise and Fall Times
Unit
pF
5
ns
Input Pulse Voltages
0.2VCC to 0.8VCC
V
Input Timing Reference Voltages
0.3VCC to 0.7VCC
V
VCC / 2
V
Output Timing Reference Voltages
Note: Output Hi-Z is defined as the point where data out is no longer driven.
PRELIMINARY
(May 2005, Version 0.0)
25
AMIC Technology Corp.
A25L80P
Figure 18. AC Measurement I/O Waveform
Input Levels
Input and Output
Timing Reference Levels
0.8VCC
0.7VCC
0.5VCC
0.3VCC
0.2VCC
PRELIMINARY
(May 2005, Version 0.0)
26
AMIC Technology Corp.
A25L80P
Table 13. AC Characteristics
Symbol
Alt.
Parameter
fC
fC
Clock Frequency for the following instructions: FAST_READ, PP,
SE, BE, DP, RES, RDID, WREN, WRDI, RDSR, WRSR
Clock Frequency for READ instructions
fR
tCH
1
tCLH
tCL
1
tCLL
Max.5
Unit
D.C.
50
MHz
D.C.
33
MHz
Min.
Clock High Time
5
Typ.
9
9
ns
tCLCH 2
Clock Rise Time3 (peak to peak)
0.1
V/ns
tCHCL 2
Clock Fall Time3 (peak to peak)
0.1
V/ns
S Active Setup Time (relative to C)
5
ns
S Not Active Hold Time (relative to C)
5
ns
tSLCH
tCSS
tCHSL
Clock Low Time
ns
tDVCH
tDSU
Data In Setup Time
5
ns
tCHDX
tDH
Data In Hold Time
5
ns
tCHSH
S Active Hold Time (relative to C)
5
ns
tSHCH
S Not Active Setup Time (relative to C)
5
ns
100
ns
tSHSL
tCSH
S Deselect Time
tSHQZ 2
tDIS
Output Disable Time
8
ns
tCLQV
tV
Clock Low to Output Valid
8
ns
tCLQX
tHO
Output Hold Time
0
ns
tHLCH
HOLD Setup Time (relative to C)
5
ns
tCHHH
HOLD Hold Time (relative to C)
5
ns
tHHCH
HOLD Setup Time (relative to C)
5
ns
HOLD Hold Time (relative to C)
5
tCHHL
ns
tHHQX 2
tLZ
HOLD to Output Low-Z
8
ns
tHLQZ 2
tHZ
HOLD to Output High-Z
8
ns
tWHSL 4
Write Protect Setup Time
20
ns
tSHWL 4
Write Protect Hold Time
100
ns
tDP
2
S High to Deep Power-down Mode
3
µs
tRES1 2
S High to Standby Mode without Electronic Signature Read
30
µs
tRES2 2
S High to Standby Mode with Electronic Signature Read
30
µs
tW
Write Status Register Cycle Time
5
15
ms
tpp
Page Program Cycle Time
3
5
ms
tSE
Sector Erase Cycle Time
1
3
s
tBE
Bulk Erase Cycle Time
10
40
s
Note: 1. tCH + tCL must be greater than or equal to 1/ fC
2. Value guaranteed by characterization, not 100% tested in production.
3. Expressed as a slew-rate.
4. Only applicable as a constraint for a WRSR instruction when SRWD is set at 1.
PRELIMINARY
(May 2005, Version 0.0)
27
AMIC Technology Corp.
A25L80P
Figure 19. Serial Input Timing
tSHSL
S
tCHSL
tSLCH
tCHSH
tSHCH
C
tCHCL
tDVCH
tCLCH
tCHDX
D
Q
MSB IN
LSB IN
High Impedance
Figure 20. Write Protect Setup and Hold Timing during WRSR when SRWD=1
W
tSHWL
tSHSL
S
C
D
High Impedance
Q
PRELIMINARY
(May 2005, Version 0.0)
28
AMIC Technology Corp.
A25L80P
Figure 21. Hold Timing
S
tHLCH
tHHCH
tCHHL
C
tCHHH
tHLQZ
tHHQX
D
Q
HOLD
Figure 22. Output Timing
S
tCH
C
tCLQV
tCLQX
tCL
tCLQV
tCLQX
D
LSB OUT
tQLQH
tQHQL
Q
ADDR.LSB IN
PRELIMINARY
(May 2005, Version 0.0)
29
AMIC Technology Corp.
A25L80P
Part Numbering Scheme
A25 X XX X X XX X X X
Package Material
Blank: normal
F: PB free
Temperature*
Speed - MHz Operating Frequency
Package
MW = SOP8
MF = SOP16
Device Version*
Device Function
P = Page Program &
Sector Erase
Device Density
05 = 512 Kbit
40 = 4 Mbit
80 = 8 Mbit
16 = 16 Mbit
Device Voltage
L = 2.7-3.6V
Device Type
A25 = AMIC Serial Flash
* Optional
PRELIMINARY
(May 2005, Version 0.0)
30
AMIC Technology Corp.
A25L80P
Ordering Information
Part No.
Speed (MHz)
Active Read
Current
Typ. (mA)
Program/Erase
Current
Typ. (mA)
Standby
Current
Typ. (μA)
A25L80PMW-50
Package
8 Pin SOP
A25L80PMW-50F
8 Pin Pb-Free SOP
50
8
15
50
A25L80PMW-50U
8 Pin SOP
A25L80PMW-50UF
8 Pin Pb-Free SOP
A25L80PMF-50
16 Pin SOP
A25L80PMF-50F
16 Pin Pb-Free SOP
50
8
15
A25L80PMF-50U
50
16 Pin SOP
A25L80PMF-50UF
16 Pin Pb-Free SOP
-U is for industrial operating temperature range: -40°C ~ +85°C
PRELIMINARY
(May 2005, Version 0.0)
31
AMIC Technology Corp.
A25L80P
Package Information
unit: mm
5
1
4
E
8
E1
SOP 8L (209mil) Outline Dimensions
C
A2
A
D
A1
e
GAGE PLANE
SEATING PLANE
θ
0.25
b
L
Dimensions in mm
Symbol
Min
Nom
Max
A
1.75
1.95
2.16
A1
0.05
0.15
0.25
A2
1.70
1.80
1.91
0.48
b
0.35
0.42
C
0.19
0.20
0.25
D
5.13
5.23
5.33
E
7.70
7.90
8.10
E1
5.18
5.28
5.38
e
1.27 BSC
L
0.50
0.65
0.80
θ
0°
-
8°
Notes:
Maximum allowable mold flash is 0.15mm at the package
ends and 0.25mm between leads
PRELIMINARY
(May 2005, Version 0.0)
32
AMIC Technology Corp.
A25L80P
Package Information
unit: inch
SOP 16L (300mil) Outline Dimensions
0.008 typ.
D
H
E
1
0.02 x 45
9
16
8
0.016 typ.
A
0.050 typ.
D
SEATING PLANE
θ
A1
0.004max.
L
Dimensions in inch
Symbol
Min
Max
A
0.093
0.104
A1
0.004
0.012
D
0.398
0.413
E
0.291
0.299
H
0.394
0.419
L
0.016
0.050
θ
0°
8°
Notes:
1. Dimensions “D” does not include mold flash,
protrusions or gate burrs.
2. Dimensions “E” does not include interlead flash, or
protrusions.
PRELIMINARY
(May 2005, Version 0.0)
33
AMIC Technology Corp.