Features • Low-voltage and Standard-voltage Operation – 1.8 (VCC = 1.8V to 5.5V) • User-selectable Internal Organization – 1K: 128 x 8 or 64 x 16 Three-wire Serial Interface 2 MHz Clock Rate (5V) Self-timed Write Cycle (5 ms max) High Reliability – Endurance: 1 Million Write Cycles – Data Retention: 100 Years • 8-lead JEDEC PDIP, 8-lead JEDEC SOIC, 8-lead Ultra Thin mini-MAP (MLP 2x3), 8-lead TSSOP and 8-ball dBGA2 Packages • Die Sales: Wafer Form, Tape and Reel, and Bumped Wafers • • • • Three-wire Serial EEPROM 1K (128 x 8 or 64 x 16) Description The AT93C46D provides 1024 bits of serial electrically erasable programmable readonly memory (EEPROM), organized as 64 words of 16 bits each (when the ORG pin is connected to VCC), and 128 words of 8 bits each (when the ORG pin is tied to ground). The device is optimized for use in many industrial and commercial applications where low-power and low-voltage operations are essential. The AT93C46D is available in space-saving 8-lead PDIP, 8-lead JEDEC SOIC, 8-lead Ultra Thin miniMAP (MLP 2x3), 8-lead TSSOP, and 8-lead dBGA2 packages. AT93C46D The AT93C46D is enabled through the Chip Select pin (CS) and accessed via a three-wire serial interface consisting of Data Input (DI), Data Output (DO), and Shift Clock (SK). Upon receiving a Read instruction at DI, the address is decoded and the data is clocked out serially on the DO pin. The Write cycle is completely self-timed, and no separate Erase cycle is required before Write. The Write cycle is only enabled when the part is in the Erase/Write Enable state. When CS is brought high following the initiation of a Write cycle, the DO pin outputs the Ready/Busy status of the part. The AT93C46D is available in 1.8 (1.8V to 5.5V) version. Table 0-1. Pin Configurations Pin Name Function CS Chip Select SK Serial Data Clock DI Serial Data Input DO Serial Data Output GND Ground VCC Power Supply ORG Internal Organization NC No Connect 8-lead SOIC CS SK DI DO 1 2 3 4 8 7 6 5 8-lead dBGA2 VCC NC ORG GND VCC NC ORG GND 8 1 7 2 6 3 5 4 CS SK D1 D0 Bottom View 8-lead PDIP CS SK DI DO 1 2 3 4 8 7 6 5 8-lead Ultra Thin mini-MAP (MLP 2x3) VCC NC ORG GND VCC NC ORG GND CS SK 3 DI 4 DO 8 1 7 2 6 5 Bottom View 8-lead TSSOP CS SK DI DO 1 2 3 4 8 7 6 5 VCC NC ORG GND 5193F–SEEPR–1/08 1. Absolute Maximum Ratings* Operating Temperature......................................−55°C to +125°C Storage Temperature .........................................−65°C to +150°C Voltage on Any Pin with Respect to Ground ........................................ −1.0V to +7.0V Maximum Operating Voltage .......................................... 6.25V *NOTICE: Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability DC Output Current........................................................ 5.0 mA Figure 1-1. Notes: Block Diagram 1. When the ORG pin is connected to VCC, the “x 16” organization is selected. When it is connected to ground, the “x 8” organization is selected. If the ORG pin is left unconnected and the application does not load the input beyond the capability of the internal 1 Meg ohm pullup, then the “x 16” organization is selected. 2. For the AT93C46D, if the “x 16” organization is the mode of choice and pin 6 (ORG) is left unconnected, Atmel® recommends using AT93C46E device. For more details, see the AT93C46E datasheet. 2 AT93C46D 5193F–SEEPR–1/08 AT93C46D Table 1-1. Pin Capacitance(1) Applicable over recommended operating range from TA = 25°C, f = 1.0 MHz, VCC = +1.8V (unless otherwise noted) Symbol Test Conditions COUT CIN Note: Max Units Conditions Output Capacitance (DO) 5 pF VOUT = 0V Input Capacitance (CS, SK, DI) 5 pF VIN = 0V 1. This parameter is characterized and is not 100% tested. Table 1-2. DC Characteristics Applicable over recommended operating range from: TAI = −40°C to +85°C, VCC = +1.8V to +5.5V (unless otherwise noted) Symbol Parameter VCC1 Supply Voltage VCC2 Test Condition Min Typ Max Unit 1.8 5.5 V Supply Voltage 2.7 5.5 V VCC3 Supply Voltage 4.5 5.5 V ICC Supply Current ISB1 Standby Current ISB2 READ at 1.0 MHz 0.5 2.0 mA WRITE at 1.0 MHz 0.5 2.0 mA VCC = 1.8V CS = 0V 0.4 1.0 µA Standby Current VCC = 2.7V CS = 0V 6.0 10.0 µA ISB3 Standby Current VCC = 5.0V CS = 0V 10.0 15.0 µA IIL Input Leakage VIN = 0V to VCC 0.1 1.0 µA Output Leakage VIN = 0V to VCC 0.1 1.0 µA IOL VIL1 (1) Input Low Voltage VIH1(1) Input High Voltage VIL2(1) Input Low Voltage (1) VIH2 Input High Voltage VOL1 Output Low Voltage VOH1 Output High Voltage VOL2 Output Low Voltage VOH2 Output High Voltage Note: VCC = 5.0V 2.7V ≤ VCC ≤ 5.5V 1.8V ≤ VCC ≤ 2.7V 2.7V ≤ VCC ≤ 5.5V 1.8V ≤ VCC ≤ 2.7V −0.6 0.8 2.0 VCC + 1 −0.6 VCC x 0.3 VCC x 0.7 VCC + 1 IOL = 2.1 mA IOH = −0.4 mA 0.4 2.4 IOL = 0.15 mA IOH = −100 µA V V V 0.2 VCC – 0.2 V V V 1. VIL min and VIH max are reference only and are not tested. 3 5193F–SEEPR–1/08 Table 1-3. AC Characteristics Applicable over recommended operating range from TAI = −40°C to + 85°C, VCC = +2.7V to +5.5V, CL = 1 TTL Gate and 100 pF (unless otherwise noted) Symbol Parameter Test Condition fSK SK Clock Frequency 4.5V ≤ VCC ≤ 5.5V 2.7V ≤ VCC ≤ 5.5V 1.8V ≤ VCC ≤ 5.5V 0 0 0 tSKH SK High Time 4.5V ≤ VCC ≤ 5.5V 2.7V ≤ VCC ≤ 5.5V 1.8V ≤ VCC ≤ 5.5V 250 250 1000 ns tSKL SK Low Time 4.5V ≤ VCC ≤ 5.5V 2.7V ≤ VCC ≤ 5.5V 1.8V ≤ VCC ≤ 5.5V 250 250 1000 ns tCS Minimum CS Low Time 4.5V ≤ VCC ≤ 5.5V 2.7V ≤ VCC ≤ 5.5V 1.8V ≤ VCC ≤ 5.5V 250 250 1000 ns tCSS CS Setup Time Relative to SK 4.5V ≤ VCC ≤ 5.5V 2.7V ≤ VCC ≤ 5.5V 1.8V ≤ VCC ≤ 5.5V 50 50 200 ns tDIS DI Setup Time Relative to SK 4.5V ≤ VCC ≤ 5.5V 2.7V ≤ VCC ≤ 5.5V 1.8V ≤ VCC ≤ 5.5V 100 100 400 ns tCSH CS Hold Time Relative to SK 0 ns tDIH DI Hold Time Relative to SK 4.5V ≤ VCC ≤ 5.5V 2.7V ≤ VCC ≤ 5.5V 1.8V ≤ VCC ≤ 5.5V 100 100 400 ns tPD1 Output Delay to “1” AC Test 4.5V ≤ VCC ≤ 5.5V 2.7V ≤ VCC ≤ 5.5V 1.8V ≤ VCC ≤ 5.5V 250 250 1000 ns tPD0 Output Delay to “0” AC Test 4.5V ≤ VCC ≤ 5.5V 2.7V ≤ VCC ≤ 5.5V 1.8V ≤ VCC ≤ 5.5V 250 250 1000 ns tSV CS to Status Valid AC Test 4.5V ≤ VCC ≤ 5.5V 2.7V ≤ VCC ≤ 5.5V 1.8V ≤ VCC ≤ 5.5V 250 250 1000 ns tDF CS to DO in High Impedance AC Test CS = VIL 4.5V ≤ VCC ≤ 5.5V 2.7V ≤ VCC ≤ 5.5V 1.8V ≤ VCC ≤ 5.5V 100 150 400 ns 5 ms tWP Write Cycle Time Endurance Note: 4 (1) 5.0V, 25°C Min 1.8V ≤ VCC ≤ 5.5V 0.1 1M Typ 3 Max Units 2 1 0.25 MHz Write Cycles 1. This parameter is ensured by characterization. AT93C46D 5193F–SEEPR–1/08 AT93C46D Table 1-4. Instruction Set for the AT93C46D Address Data SB Op Code x8 x 16 READ 1 10 A6 – A0 A5 – A0 EWEN 1 00 11XXXXX 11XXXX ERASE 1 11 A6 – A0 A5 – A0 WRITE 1 01 A6 – A0 A5 – A0 ERAL 1 00 10XXXXX 10XXXX WRAL 1 00 01XXXXX 01XXXX EWDS 1 00 00XXXXX 00XXXX Instruction Note: x8 x 16 Comments Reads data stored in memory, at specified address Write enable must precede all programming modes Erases memory location An – A0 D7 – D0 D15 – D0 Writes memory location An – A0 Erases all memory locations. Valid only at VCC = 4.5V to 5.5V D7 – D0 D15 – D0 Writes all memory locations. Valid only at VCC = 4.5V to 5.5V Disables all programming instructions The Xs in the address field represent DON’T CARE values and must be clocked. 2. Functional Description The AT93C46D is accessed via a simple and versatile three-wire serial communication interface. Device operation is controlled by seven instructions issued by the host processor. A valid instruction starts with a rising edge of CS and consists of a start bit (logic “1”) followed by the appropriate op code and the desired memory address location. READ (READ): The Read (READ) instruction contains the address code for the memory location to be read. After the instruction and address are decoded, data from the selected memory location is available at the serial output pin DO. Output data changes are synchronized with the rising edges of serial clock SK. It should be noted that a dummy bit (logic “0”) precedes the 8- or 16-bit data output string. ERASE/WRITE ENABLE (EWEN): To assure data integrity, the part automatically goes into the Erase/Write Disable (EWDS) state when power is first applied. An Erase/Write Enable (EWEN) instruction must be executed first before any programming instructions can be carried out. Please note that once in the EWEN state, programming remains enabled until an EWDS instruction is executed or VCC power is removed from the part. ERASE (ERASE): The Erase (ERASE) instruction programs all bits in the specified memory location to the logical “1” state. The self-timed erase cycle starts once the Erase instruction and address are decoded. The DO pin outputs the Ready/Busy status of the part if CS is brought high after being kept low for a minimum of 250 ns (tCS). A logic “1” at pin DO indicates that the selected memory location has been erased and the part is ready for another instruction. WRITE (WRITE): The Write (WRITE) instruction contains the 8 or 16 bits of data to be written into the specified memory location. The self-timed programming cycle tWP starts after the last bit of data is received at serial data input pin DI. The DO pin outputs the Read/Busy status of the part if CS is brought high after being kept low for a minimum of 250 ns (tCS). A logic “0” at DO indicates that programming is still in progress. A logic “1” indicates that the memory location at the specified address has been written with the data pattern contained in the instruction and the 5 5193F–SEEPR–1/08 part is ready for further instructions. A Ready/Busy status cannot be obtained if the CS is brought high after the end of the self-timed programming cycle tWP. ERASE ALL (ERAL): The Erase All (ERAL) instruction programs every bit in the memory array to the logic “1” state and is primarily used for testing purposes. The DO pin outputs the Ready/Busy status of the part if CS is brought high after being kept low for a minimum of 250 ns (tCS). The ERAL instruction is valid only at VCC = 5.0V ± 10%. WRITE ALL (WRAL): The Write All (WRAL) instruction programs all memory locations with the data patterns specified in the instruction. The DO pin outputs the Ready/Busy status of the part if CS is brought high after being kept low for a minimum of 250 ns (tCS). The WRAL instruction is valid only at VCC = 5.0V ± 10%. ERASE/WRITE DISABLE (EWDS): To protect against accidental data disturb, the Erase/Write Disable (EWDS) instruction disables all programming modes and should be executed after all programming operations. The operation of the Read instruction is independent of both the EWEN and EWDS instructions and can be executed at any time. 6 AT93C46D 5193F–SEEPR–1/08 AT93C46D 3. Timing Diagrams Figure 3-1. Synchronous Data Timing μs Note: 1. This is the minimum SK period. Table 3-1. Organization Key for Timing Diagrams AT93C46D (1K) Figure 3-2. I/O x8 x 16 AN A6 A5 DN D7 D15 READ Timing tCS High Impedance 7 5193F–SEEPR–1/08 Figure 3-3. EWEN Timing tCS CS SK DI Figure 3-4. 1 0 0 1 ... 1 EWDS Timing tCS CS SK DI Figure 3-5. 1 0 0 0 ... 0 WRITE Timing tCS CS SK DI DO 1 0 1 AN ... A0 DN ... D0 HIGH IMPEDANCE BUSY READY tWP 8 AT93C46D 5193F–SEEPR–1/08 AT93C46D Figure 3-6. WRAL Timing(1) tCS CS SK 1 DI DO 0 0 0 1 ... DN ... D0 BUSY HIGH IMPEDANCE READY tWP Note: 1. Valid only at VCC = 4.5V to 5.5V. Figure 3-7. ERASE Timing tCS CS STANDBY CHECK STATUS SK DI 1 1 1 AN AN-1 AN-2 ... A0 tDF tSV DO HIGH IMPEDANCE HIGH IMPEDANCE BUSY READY tWP 9 5193F–SEEPR–1/08 Figure 3-8. ERAL Timing(1) tCS CS CHECK STATUS STANDBY tSV tDF SK DI DO 1 0 0 1 0 BUSY HIGH IMPEDANCE HIGH IMPEDANCE READY tWP Note: 10 1. Valid only at VCC = 4.5V to 5.5V. AT93C46D 5193F–SEEPR–1/08 AT93C46D 4. AT93C46D Ordering Information Ordering Code AT93C46D-PU (Bulk form only) Voltage Package 1.8 8P3 (1) (NiPdAu Lead finish) 1.8 8S1 (2) (NiPdAu Lead finish) 1.8 8S1 AT93C46DN-SH-B AT93C46DN-SH-T AT93C46D-TH-B(1) (NiPdAu Lead finish) 1.8 8A2 AT93C46D-TH-T(2) (NiPdAu Lead finish) 1.8 8A2 AT93C46DY6-YH-T(2) (NiPdAu Lead finish) 1.8 8Y6 (2) 1.8 8U3-1 1.8 Die Sale AT93C46DU3-UU-T AT93C46D-W-11(3) Notes: Operation Range Lead-free/Halogen-free/ Industrial Temperature (−40°C to 85°C) Industrial (−40°C to 85°C) 1. “-B” denotes bulk 2. “-T” denotes tape and reel. SOIC = 4K per reel. TSSOP, Ultra Thin Mini MAP, and dBGA2 = 5K per reel. 3. Available in tape and reel, and wafer form; order as SL788 for inkless wafer form. Bumped die available upon request. Please contact Serial Interface Marketing. Package Type 8P3 8-lead, 0.300" Wide, Plastic Dual Inline Package (PDIP) 8S1 8-lead, 0.150" Wide, Plastic Gull Wing Small Outline (JEDEC SOIC) 8A2 8-lead, 0.170" Wide, Thin Shrink Small Outline Package (TSSOP) 8U3-1 8-ball, Die Ball Grid Array Package (dBGA2) 8Y6 8-lead, 2.00 mm x 3.00 mm Body, 0.50mm Pitch, Ultra-Thin Mini-MAO, Dual No Lead Package. (DFN), (MLP 2x3mm) Options −1.8 Low Voltage (1.8V to 5.5V) 11 5193F–SEEPR–1/08 5. Part Marking Scheme 5.1 AT93C46D 8-PDIP TOP MARK Seal Year | Seal Week | | | |---|---|---|---|---|---|---|---| A T M L U Y W W Y = SEAL YEAR 6: 2006 0: 2010 7: 2007 8: 2008 9: 2009 1: 2011 2: 2012 3: 2013 |---|---|---|---|---|---|---|---| 4 6 D 52 = Week 52 | Pin 1 Indicator (Dot) Lot Number to Use ALL Characters in Marking BOTTOM MARK No Bottom Mark AT93C46D 8-SOIC TOP MARK Seal Year | Seal Week | | | |---|---|---|---|---|---|---|---| A T M L H Y W W Y = SEAL YEAR 6: 2006 0: 2010 7: 2007 8: 2008 9: 2009 |---|---|---|---|---|---|---|---| 4 6 D 1: 2011 2: 2012 3: 2013 WW = SEAL WEEK 02 = Week 2 04 = Week 4 :: : :::: : :: : :::: :: 50 = Week 50 1 |---|---|---|---|---|---|---|---| * Lot Number |---|---|---|---|---|---|---|---| | Pin 1 Indicator (Dot) 12 04 = Week 4 :: : :::: : :: : :::: :: 50 = Week 50 1 |---|---|---|---|---|---|---|---| * Lot Number |---|---|---|---|---|---|---|---| 5.2 WW = SEAL WEEK 02 = Week 2 52 = Week 52 Lot Number to Use ALL Characters in Marking BOTTOM MARK No Bottom Mark AT93C46D 5193F–SEEPR–1/08 AT93C46D 5.3 AT93C46D 8-TSSOP TOP MARK Pin 1 Indicator (Dot) | |---|---|---|---| * H Y W W |---|---|---|---|---| 4 6 D Y = SEAL YEAR 6: 7: 8: 9: 2006 2007 2008 2009 0: 1: 2: 3: WW = SEAL WEEK 2010 2011 2012 2013 1 * 02 04 :: :: = = : : Week Week :::: :::: 2 4 : :: 50 = Week 50 |---|---|---|---|---| 52 = Week 52 BOTTOM MARK |---|---|---|---|---|---|---| C 0 0 |---|---|---|---|---|---|---| A A A A A A A |---|---|---|---|---|---|---| <- Pin 1 Indicator 5.4 AT93C46D 8-Ultra Thin Mini MAP TOP MARK Y = YEAR OF ASSEMBLY |---|---|---| 4 6 D |---|---|---| H 1 XX = ATMEL LOT NUMBER TO COORESPOND WITH NSEB TRACE CODE LOG BOOK. (e.g. XX = AA, AB, AC,...AX, AY, AZ) |---|---|---| Y X X |---|---|---| * | Pin 1 Indicator (Dot) Y = 6: 7: 8: SEAL YEAR 2006 0: 2010 2007 1: 2011 2008 2: 2012 9: 2009 3: 2013 13 5193F–SEEPR–1/08 5.5 AT93C46D dBGA2 TOP MARK LINE 1-------> LINE 2-------> Y 4: 5: 6: 46DU YMTC |<-- Pin 1 This Corner = ONE DIGIT YEAR CODE 2004 7: 2007 2005 8: 2008 2006 9: 2009 M = SEAL MONTH (USE ALPHA DESIGNATOR A-L) A = JANUARY B = FEBRUARY " " """"""" J = OCTOBER K = NOVEMBER L = DECEMBER TC = TRACE CODE (ATMEL LOT NUMBERS TO CORRESPOND WITH ATK TRACE CODE LOG BOOK) 14 AT93C46D 5193F–SEEPR–1/08 AT93C46D 6. Package Information 8P3 - PDIP E 1 E1 N Top View c eA End View COMMON DIMENSIONS (Unit of Measure = inches) D e D1 A2 A MIN NOM MAX A2 0.115 0.130 0.195 b 0.014 0.018 0.022 5 b2 0.045 0.060 0.070 6 b3 0.030 0.039 0.045 6 SYMBOL A b2 b3 b 4 PLCS Side View L 2 c 0.008 0.010 0.014 D 0.355 0.365 0.400 3 D1 0.005 E 0.300 0.310 0.325 4 E1 0.240 0.250 0.280 3 0.150 2 e 3 0.100 BSC eA L Notes: 0.210 NOTE 0.300 BSC 0.115 0.130 4 1. This drawing is for general information only; refer to JEDEC Drawing MS-001, Variation BA for additional information. 2. Dimensions A and L are measured with the package seated in JEDEC seating plane Gauge GS-3. 3. D, D1 and E1 dimensions do not include mold Flash or protrusions. Mold Flash or protrusions shall not exceed 0.010 inch. 4. E and eA measured with the leads constrained to be perpendicular to datum. 5. Pointed or rounded lead tips are preferred to ease insertion. 6. b2 and b3 maximum dimensions do not include Dambar protrusions. Dambar protrusions shall not exceed 0.010 (0.25 mm). 01/09/02 R 2325 Orchard Parkway San Jose, CA 95131 TITLE 8P3, 8-lead, 0.300" Wide Body, Plastic Dual In-line Package (PDIP) DRAWING NO. REV. 8P3 B 15 5193F–SEEPR–1/08 8S1 - JEDEC SOIC C 1 E E1 L N Ø TOP VIEW END VIEW e b COMMON DIMENSIONS (Unit of Measure = mm) A A1 D SIDE VIEW Note: SYMBOL MIN NOM MAX A 1.35 – 1.75 A1 0.10 – 0.25 b 0.31 – 0.51 C 0.17 – 0.25 D 4.80 – 5.05 E1 3.81 – 3.99 E 5.79 – 6.20 e NOTE 1.27 BSC L 0.40 – 1.27 θ 0° – 8° These drawings are for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc. 3/17/05 R 16 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TITLE 8S1, 8-lead (0.150" Wide Body), Plastic Gull Wing Small Outline (JEDEC SOIC) DRAWING NO. 8S1 REV. C AT93C46D 5193F–SEEPR–1/08 AT93C46D 8A2 - TSSOP 3 2 1 Pin 1 indicator this corner E1 E L1 N L Top View End View COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL A b D MIN NOM MAX NOTE 2.90 3.00 3.10 2, 5 4.40 4.50 3, 5 E E1 e D A2 6.40 BSC 4.30 A – – 1.20 A2 0.80 1.00 1.05 b 0.19 – 0.30 e Side View L 0.65 BSC 0.45 L1 Notes: 4 0.60 0.75 1.00 REF 1. This drawing is for general information only. Refer to JEDEC Drawing MO-153, Variation AA, for proper dimensions, tolerances, datums, etc. 2. Dimension D does not include mold Flash, protrusions or gate burrs. Mold Flash, protrusions and gate burrs shall not exceed 0.15 mm (0.006 in) per side. 3. Dimension E1 does not include inter-lead Flash or protrusions. Inter-lead Flash and protrusions shall not exceed 0.25 mm (0.010 in) per side. 4. Dimension b does not include Dambar protrusion. Allowable Dambar protrusion shall be 0.08 mm total in excess of the b dimension at maximum material condition. Dambar cannot be located on the lower radius of the foot. Minimum space between protrusion and adjacent lead is 0.07 mm. 5. Dimension D and E1 to be determined at Datum Plane H. 5/30/02 R 2325 Orchard Parkway San Jose, CA 95131 TITLE 8A2, 8-lead, 4.4 mm Body, Plastic Thin Shrink Small Outline Package (TSSOP) DRAWING NO. 8A2 REV. B 17 5193F–SEEPR–1/08 8U3-1 – dBGA2 E D 1. b A1 PIN 1 BALL PAD CORNER A2 Top View A Side View PIN 1 BALL PAD CORNER 1 2 3 4 8 7 6 5 (d1) d e COMMON DIMENSIONS (Unit of Measure - mm) (e1) SYMBOL Bottem View 8 SOLDER BALLS 1. This drawing is for general information only. 2. Dimension 'b' is measured at maximum solder ball diameter. MIN NOM MAX A 0.73 0.79 0.85 A1 0.09 0.14 0.19 A2 0.40 0.45 0.50 b 0.20 0.25 0.30 D 1.50 BSC E 2.0 BSC e 0.50 BSC e1 0.25 REF d 1.00 BSC d1 0.25 REF NOTE 2 5/3/05 R 18 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TITLE 8U3-1, 8-ball, 1.50 x 2.00 mm Body, 0.50 mm pitch, Small Die Ball Grid Array Package (dBGA2) DRAWING NO. REV. PO8U3-1 B AT93C46D 5193F–SEEPR–1/08 AT93C46D 8Y6 – MLP 2x3 D2 A b (8X) E E2 Pin 1 Index Area Pin 1 ID L (8X) D A2 e (6X) A1 1.50 REF. COMMON DIMENSIONS (Unit of Measure = mm) A3 SYMBOL MIN 2.00 BSC E 3.00 BSC MAX D2 1.40 1.50 1.60 E2 - - 1.40 A - - 0.60 A1 0.0 0.02 0.05 A2 - - 0.55 A3 L b NOTE 0.20 REF 0.20 e Notes: NOM D 0.30 0.40 0.50 BSC 0.20 0.25 0.30 2 1. This drawing is for general information only. Refer to JEDEC Drawing MO-229, for proper dimensions, tolerances, datums, etc. 2. Dimension b applies to metallized terminal and is measured between 0.15 mm and 0.30 mm from the terminal tip. If the terminal has the optional radius on the other end of the terminal, the dimension should not be measured in that radius area. 3. Soldering the large thermal pad is optional, but not recommended. No electrical connection is accomplished to the device through this pad, so if soldered it should be tied to ground 10/16/07 R 2325 Orchard Parkway San Jose, CA 95131 DRAWING NO. TITLE 8Y6, 8-lead 2.0 x 3.0 mm Body, 0.50 mm Pitch, Utlra Thin Mini-Map, 8Y6 Dual No Lead Package (DFN) ,(MLP 2x3) REV. D 19 5193F–SEEPR–1/08 7. Revision History 20 Doc. Rev. Date Comments 5193F 1/2008 Removed ‘preliminary’ status 5193E 11/2007 Modified ‘max’ value in AC Characteristics table 5193D 8/2007 Moved Pinout figure Added new feature for Die Sales Modified Ordering Information table layout Modified Park Marking Schemes 5193C 6/2007 Updated to new template Added Product Markup Scheme Added Technical email contact 5193C 3/2007 Corrected Figures 4 and 5. 5193B 2/2007 Added ‘Ultra Thin’ description to 8-lead Mini-MAP package. 5193A 1/2007 Initial document release. AT93C46D 5193F–SEEPR–1/08 Headquarters International Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131 USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Atmel Asia Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimshatsui East Kowloon Hong Kong Tel: (852) 2721-9778 Fax: (852) 2722-1369 Atmel Europe Le Krebs 8, Rue Jean-Pierre Timbaud BP 309 78054 Saint-Quentin-enYvelines Cedex France Tel: (33) 1-30-60-70-00 Fax: (33) 1-30-60-71-11 Atmel Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Technical Support [email protected] Sales Contact www.atmel.com/contacts Product Contact Web Site www.atmel.com Literature Requests www.atmel.com/literature Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. ©2008 Atmel Corporation. All rights reserved. Atmel ®, logo and combinations thereof, and others, are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. 5193F–SEEPR–1/08