SMT inductors SIMID series, SIMID 0603-C Series/Type: B82496C Date: October 2008 %BUB4IFFU © EPCOS AG 2008. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without EPCOS’ prior express consent is prohibited. SMT inductors, SIMID series B82496C SIMID 0603-C Size 0603 (EIA) and/or 1608 (IEC) Rated inductance 1 nH to 220 nH Rated current 110 mA to 1800 mA Construction ■ Copper-plated ceramic core ■ Laser-cut winding, epoxy-coated Features Temperature range up to 150 °C High resonance frequency Close inductance tolerance Free of polarization effect High mechanical stability Qualified to AEC-Q200 Suitable for lead-free reflow soldering as referenced in JEDEC J-STD 020C ■ RoHS-compatible ■ ■ ■ ■ ■ ■ ■ Applications Resonant circuits, impedance matching for Multimedia Car access systems Wireless communication systems TPMS (Tire Pressure Monitoring System) GPS (Global Positioning System) Digital cameras ■ ■ ■ ■ ■ ■ Terminals ■ Base material Al2O3 ceramic with Cu layer ■ Layer composition Ni, Sn (lead-free) ■ Electro-plated Marking ■ No marking on component ■ Minimum data on reel: Manufacturer, ordering code, L value, quantity, date of packing Delivery mode and packing unit ■ 8-mm cardboard tape, wound on 180-mm ∅ reel ■ Bulk case on request ■ Packing unit: 4000 pcs./reel Please read Cautions and warnings and Important notes at the end of this document. 2 10/08 SMT inductors, SIMID series B82496C SIMID 0603-C 0.3±0.2 A 0.8±0.1 Dimensional drawing and layout recommendation 0.3±0.2 C 0.8±0.1 1.6±0.1 B IND0042-K IND0041-C Dimensions in mm A B C 0.8 ±0.1 2.3 ±0.3 0.9 ±0.1 Taping and packing 2±0.05 1.9±0.1 0.95±0.05 <_ 1.15 1.1±0.1 8±0.2 4±0.1 _0 1.5 +0.1 3.5±0.05 Reel 1.75±0.1 Cardboard tape 4±0.1 Direction of unreeling IND0553-H-E Dimensions in mm Please read Cautions and warnings and Important notes at the end of this document. 3 10/08 SMT inductors, SIMID series B82496C SIMID 0603-C Technical data and measuring conditions Rated inductance LR Measured with impedance analyzer Agilent 4291A and test fixture Agilent 16196A at frequency fL, 0.1 V, 20 °C Q factor Qmin, Qtyp Measured with impedance analyzer Agilent 4291A and test fixture Agilent 16196A, Qmin measured at frequency fQ, 20 °C Rated temperature TR 125 °C Rated current IR Maximum permissible DC with a temperature increase of ≤ 15 K at rated temperature Self-resonance frequency fres,min Measured with network analyzer Agilent 8720D, 20 °C DC resistance Rmax Measured at 20 °C Solderability (lead-free) Sn95.5Ag3.8Cu0.7: (245 ±5) °C, (5 ±0.3) s Wetting of soldering area ≥ 95% (based on IEC 60068-2-58) Resistance to soldering heat 260 °C, 40 s (as referenced in JEDEC J-STD 020C) Climatic category 55/150/56 (to IEC 60068-1) Storage conditions Mounted: –55 °C … +150 °C Packaged: –25 °C … +40 °C, ≤ 75% RH Weight Approx. 4 mg Please read Cautions and warnings and Important notes at the end of this document. 4 10/08 SMT inductors, SIMID series B82496C SIMID 0603-C Characteristics and ordering codes Ordering code1)2) (reel packing) Qtyp (at 800 MHz) fL; fQ IR Rmax fres,min MHz mA Ω GHz 7 60 100 1800 0.02 16 B82496C3109+000 8 60 100 1800 0.025 15 B82496C3129+000 1.5 8 50 100 1500 0.03 13 B82496C3159+000 1.8 12 50 100 1500 0.033 12 B82496C3189+000 2.2 14 50 100 1500 0.035 10 B82496C3229+000 2.7 14 40 100 1400 0.04 10 B82496C3279+000 3.3 14 40 100 1200 0.06 9 B82496C3339+000 14 40 100 1100 0.065 8 B82496C3399+000 14 40 100 800 0.10 7 B82496C3479+000 5.6 14 40 100 700 0.15 6 B82496C3569+000 6.8 14 40 100 700 0.15 6 B82496C3689+000 8.2 14 40 100 650 0.18 6 B82496C3829+000 14 40 100 600 0.20 5 B82496C3100+000 14 40 100 450 0.35 5 B82496C3120+000 15 14 40 100 420 0.40 4.5 B82496C3150+000 18 14 40 100 400 0.45 4.0 B82496C3180+000 22 14 40 100 380 0.50 4.0 B82496C3220+000 27 14 35 100 360 0.55 3.0 B82496C3270+000 33 14 35 100 350 0.60 3.0 B82496C3330+000 39 14 35 100 300 0.80 2.5 B82496C3390+000 47 14 35 100 270 0.95 2.5 B82496C3470+000 56 14 35 100 250 1.2 2.5 B82496C3560+000 68 14 35 100 230 1.3 2.0 B82496C3680+000 82 14 35 100 220 1.5 2.0 B82496C3820+000 100 14 30 100 200 1.8 1.8 B82496C3101+000 120 5 30 25.2 160 3.0 1.8 B82496C3121+000 150 5 30 25.2 130 5.0 1.6 B82496C3151+000 180 4 25 25.2 120 6.0 1.4 B82496C3181+000 220 4 25 25.2 110 7.0 1.3 B82496C3221+000 LR Tolerance Qmin nH 1.0 1.2 3.9 4.7 10 12 ±0.3 nH ±0.2 nH ^ ^ A Z ±5% ^ J ±0.2 nH ^ Z ±5% ±2% ^ ^ J G Special versions on request. Higher currents possible at temperatures <TR on request. Sample kit available (see also chapter “Sample kits”. Ordering code: B82496X001 1) Replace the + by the code letter for the required inductance tolerance. 2) For bulk case the last digit has to be a »1«. Example: B82496C3109A001 Please read Cautions and warnings and Important notes at the end of this document. 5 10/08 SMT inductors, SIMID series B82496C SIMID 0603-C Impedance |Z| versus frequency f measured with impedance analyzer Agilent 4291A/16196A, typical values at 20 °C IND0043-T 10 5 Ω | Z | 10 Inductance L versus DC load current IDC measured with LCR meter Agilent 4275A, typical values at 20 °C 10 nH B82496C _6 IND0045-5 B82496C 4 220 nH L 10 3 10 _7 100 nH _8 10 nH _9 1 nH 10 2 10 1 10 10 0 10 10 10 220 nH 100 nH 10 nH 1 nH _1 _2 10 _3 10 6 10 7 10 8 Hz 10 f 10 9 IND0044-2 B82496C Iop IR 1 nH 80 _2 10 _1 10 0 A 10 1 I DC IND0046-L-E 1.2 90 Q 10 Current derating Iop/IR versus ambient temperature TA (rated temperature TR = 125 °C) Q factor versus frequency f measured with impedance analyzer Agilent 4291A/16196A, typical values at 20 °C 100 _ 10 70 B82496C 1.0 0.8 60 10 nH 0.6 50 40 0.4 30 20 0.2 10 220 nH 0 7 10 10 8 10 9 100 nH 0 Hz 10 10 f 6 0 10/08 20 40 60 80 100 120 C 160 TA Cautions and warnings ■ Please note the recommendations in our Inductors data book (latest edition) and in the data sheets. – Particular attention should be paid to the derating curves given there. – The soldering conditions should also be observed. Temperatures quoted in relation to wave soldering refer to the pin, not the housing. ■ If the components are to be washed varnished it is necessary to check whether the washing varnish agent that is used has a negative effect on the wire insulation, any plastics that are used, or on glued joints. In particular, it is possible for washing varnish agent residues to have a negative effect in the long-term on wire insulation. ■ The following points must be observed if the components are potted in customer applications: – Many potting materials shrink as they harden. They therefore exert a pressure on the plastic housing or core. This pressure can have a deleterious effect on electrical properties, and in extreme cases can damage the core or plastic housing mechanically. – It is necessary to check whether the potting material used attacks or destroys the wire insulation, plastics or glue. – The effect of the potting material can change the high-frequency behaviour of the components. ■ Ferrites are sensitive to direct impact. This can cause the core material to flake, or lead to breakage of the core. ■ Even for customer-specific products, conclusive validation of the component in the circuit can only be carried out by the customer. Please read Cautions and warnings and Important notes at the end of this document. 7 10/08 Important notes The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. We nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application. As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether an EPCOS product with the properties described in the product specification is suitable for use in a particular customer application. 2. We also point out that in individual cases, a malfunction of electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified. In customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health (e.g. in accident prevention or life-saving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of an electronic component. 3. The warnings, cautions and product-specific notes must be observed. 4. In order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as hazardous). Useful information on this will be found in our Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more detailed questions, please contact our sales offices. 5. We constantly strive to improve our products. Consequently, the products described in this publication may change from time to time. The same is true of the corresponding product specifications. Please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. We also reserve the right to discontinue production and delivery of products. Consequently, we cannot guarantee that all products named in this publication will always be available. The aforementioned does not apply in the case of individual agreements deviating from the foregoing for customer-specific products. 6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms of Delivery for Products and Services in the Electrical Industry” published by the German Electrical and Electronics Industry Association (ZVEI). 7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CSMP, CSSP, CTVS, DSSP, MiniBlue, MKK, MLSC, MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMDAD, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap are trademarks registered or pending in Europe and in other countries. Further information will be found on the Internet at www.epcos.com/trademarks. 8 03/09