SOLID TANTALUM ELECTROLYTIC CAPACITORS F98 Resin-molded Chip, High Capacitance Series Adapted to the RoHS directive (2002/95/EC). Specifications Item Performance Characteristics Category Temperature Range --55 ~ +125°C (Rated temperature : 85°C) Capacitance Tolerance ±20% (at 120Hz) Dissipation Factor(120Hz) Refer to the list below (* 1) ESR(100kHz) Refer to the list below (* 1) Leakage Current After 5 minute's application of rated voltage, leakage current at 20°C is not more than 0.1CV or 0.5µA, whichever is greater. Damp Heat At 40°C, 90 ~ 95% R.H., For 500hours (No voltage applied) Capacitance Change Refor to the list below (* 1) Dissipation Factor 150% or less of initial specified value Leakage Current 200% or less of initial specified value Temperature Cycles At --55°C / +125°C, For 30 minutes each, 5 cycles Capacitance Change Refor to the list below (* 1) Dissipation Factor 150% or less of initial specified value Leakage Current Initial specified value or less Resistance to Soldering Heat At 260°C, For 10 seconds, Reflow, Capacitance Change Refor to the list below (* 1) Leakage Current Initial specified value or less Leakage Current Initial specified value or less Surge∗ After application of surge in series with a 1kΩ resistor at the rate of 30 seconds ON, 30 seconds OFF, for 1000 successive test cycles at 85°C, capacitors meet the characteristics requirements listed below. Refor to the list below (* 1) Capacitance Change Dissipation Factor 150% or less of initial specified value Leakage Current 200% or less of initial specified value Endurance∗ After 1000 hours' application of rated voltage in series with a 3Ω resistor at 85°C, capacitors meet the characteristic requirements listed below Refor to the list below (* 1) Capacitance Change Dissipation Factor 150% or less of initial specified value Leakage Current 200% or less of initial specified value Shear Test After applying the pressure load of 5N for 10±1 seconds horizontally to the center of capacitor side body which has no electrode and has been soldered beforehand on an aluminum substrate, there shall be found neither exfoliation nor its sign at the terminal electrode. Terminal Strength Keeping a capacitor surface-mounted on a substrate upside down and supporting the substrate at both of the opposite bottom points 45mm apart from the center of the capacitor, the pressure strength is applied with 20 a specified jig at the center of the R230 substrate so that the substrate may bend by 1mm as illustrated. Then, there shall be found no 45 45 remarkable abnormality on the capacitor terminals. Type numbering system (Example : 6.3V 10 µF) 1 2 3 F 9 8 4 5 6 0 J 7 8 9 10 11 1 0 6 M M Taping code (Refer to page 267 for details) Case code Capacitance tolerance Rated Capacitance Rated voltage Series Drawing L W1 H W2 S1 S2 S1 (mm) Cace Code W2 W1 L H S1 S2 M 1.6 ± 0.1 0.85 ± 0.1 0.65 ± 0.1 0.8 ± 0.1 0.5 ± 0.1 0.6 ± 0.1 S 2.0 ± 0.1 1.25 ± 0.1 1.0 ± 0.1 0.9 ± 0.1 0.8 ± 0.1 0.5 ± 0.1 1mm Marking J ∗ As for the surge and derated voltage at 125˚C, refer to page 266 for details. Rated voltage (Voltage code) Standard ratings V Cap.(µF) Code 1 105 2.2 225 4.7 475 10 106 22 226 33 336 47 476 68 686 100 107 5N (0.51kg • f) For 10 ± 1seconds 2.5 0E M 4 0G 6.3 0J 10 1A Rated Volt (V) Rated Capacitance (µF) Case code 47 22 16 1C 20 1D 2.5 M M 4 Leakage Current (µA) Disspation Factor (% @120Hz) M F980E476MMA 1.2 30 4 ± 30 M F980G226MMA 0.9 15 7.5 ± 30 33 M F980G336MMA 1.3 30 4 ± 30 ESR *1∆C/C (Ω@100kHz) (%) M M 68 S F980G686MSA 2.7 30 4 ± 30 M M M 4.7 M F980J475MMA 0.5 20 7.5 ± 30 M M S 10 M F980J106MMA 0.6 8 6 ± 30 M M S 22 M F980J226MMA 1.4 20 6 ± 30 M (M) S 47 S F980J476MSA 3.0 25 6 ± 30 (M) S 2.2 M F981A225MMA 0.5 6 7.5 ± 30 4.7 M F981A475MMA 0.5 6 6 ± 30 10 M F981A106MMA 1.0 20 7.5 ± 30 22 S F981A226MSA 2.2 20 4 ± 20 33 S F981A336MSA 3.3 30 6 ± 30 1 M F981C105MMA 0.5 6 10 ± 30 2.2 M F981C225MMA 0.5 6 10 ± 30 4.7 M F981C475MMA 0.8 12 12 ± 30 10 S F981C106MSA 1.6 18 4 ± 20 1 M F981D105MMA 0.5 6 10 ± 30 6.3 S (S) Part Number (S) 10 ( ) The series in parentheses are being developed. Please contact to your local Nichicon sales office when these series are being designed in your application. 16 20 CAT.8100V