DC-DC Converter Bricks, Open/Enclosed BAQ SERIES, 1/4 BRICK, UP TO 200W FEATURES: 5 years warranty Output current up to 30A 1500Vdc isolation voltage Efficiency up to 93% Operating temperature range -40°C to +85°C Under voltage, over current, short circuit, over voltage protection Remote on/off Adjustable output voltage Output voltage (Vdc) Output current (A) Efficiency Typ. 3.3 25.00 88% 5.0 10.00 90% 5.0 15.00 91% 5.0 20.00 90% 5.0 30.00 90% 12.0 4.20 90% 12.0 8.33 93% 12.0 16.67 93% BAQ48-12V20 BAQ48-12V25 1.2 20.0 87% 1.2 25.0 87% BAQ48-12V30 1.2 30.0 87% BAQ48-15V25 1.5 25.0 88% BAQ48-18V10 1.8 10.0 88% BAQ48-18V15 1.8 15.0 88% BAQ48-18V20 1.8 20.0 89% BAQ48-18V25 1.8 25.0 88% 1.8 30.0 88% 2.5 10.0 89% BAQ48-25V15 2.5 15.0 91% BAQ48-25V20 2.5 20.0 91% BAQ48-25V25 2.5 25.0 91% BAQ48-25V30 2.5 30.0 88% BAQ48-33V10 3.3 10.0 88% BAQ48-33V15 3.3 15.0 91% BAQ48-33V20 BAQ48-33V25 3.3 20.0 91% 3.3 25.0 91% Model BAQ24-33V25 BAQ24-50V10 BAQ24-50V15 BAQ24-50V20 BAQ24-50V30 BAQ24-120V4 BAQ24-120V8 BAQ24-120V17 BAQ48-18V30 BAQ48-25V10 www.pairuigroup.com Input voltage (Vdc) 24(18~36) 48(36~72) Page: 1/5 Date: 02/09/2014 DC-DC Converter Bricks, Open/Enclosed BAQ SERIES, 1/4 BRICK, UP TO 200W Model BAQ48-33V30 BAQ48-33V35 BAQ48-50V6 BAQ48-50V10 BAQ48-50V15 BAQ48-50V20 BAQ48-50V25 BAQ48-50V30 BAQ48-120V8 BAQ48-120V10 BAQ48-120V13 BAQ48-120V25 Input voltage (Vdc) Output voltage (Vdc) Output current (A) Efficiency Typ. 3.3 30.0 91% 3.3 35.0 91% 5.0 6.0 89% 5.0 10.0 93% 5.0 15.0 91% 5.0 20.0 94% 5.0 25.0 90% 5.0 30.0 91% 12.0 8.3 91% 12.0 10.0 92% 12.0 12.5 91% 12.0 25.0 93% 48(36~72) Notes: 1. Other input and output models may available on request; 2. You may request for the models with heatsink, plus “R” in the suffix, e.g. BAQ24-33V25R. ELECTRICAL Input voltage range 24Vdc 18-36Vdc 48Vdc 36-72Vdc OFF: High level or left close Negative logic ON: Low level or grounded Remote control ON: High level or left open Positive logic OFF: Low level or grounded Output power Input voltage range Output voltage Single output Output voltage accuracy Input voltage range Output voltage adjustable Positive logic ±10% Line regulation Full load ±0.2% Load regulation 10%-100% full load ±0.5% Dynamic response (transient/recovery time) 30-200W 1.2/1.5/1.8/2.5/3.3/5/12Vdc ±1% 25%-50%-75% load capability ∆Vo/∆t: ±4.0%/500μs Output=12V, 200mVp-p Ripple and noise Parallel test, 20MHz wide range Operating frequency Typical Isolation voltage Input to output 1500Vdc Input to case 1050Vdc 300KHz typ. Output to case Isolation resistance www.pairuigroup.com Other, 100mVp-p max. 500Vdc --- 10MΩ Page: 2/5 Date: 02/09/2014 DC-DC Converter Bricks, Open/Enclosed BAQ SERIES, 1/4 BRICK, UP TO 200W ELECTRICAL IEC-60950-1, UL-60950-1 Safety --- Temperature coefficient --- Operating temperature range Auxiliary heat sink Storage temperature range --- Over temperature protection Typical Under voltage protection --- Yes Over current protection --- Yes Short circuit protection --- Yes Over voltage protection --- Yes Relative humidity --- 95% max. MTBF Bellcore TR-332, 25°C EN-60950-1, GB4943 200ppm -40°C to +85°C -40°C to +125°C 110°C typ. 2x106Hrs Notes: Unless otherwise specified, all the parameters of the test conditions are as follows: ambient temperature 25 , the nominal input voltage, pure resistive nominal load. ℃ MECHANICAL WITHOUT HEATSINK www.pairuigroup.com WITH HEATSINK Page: 3/5 Date: 02/09/2014 DC-DC Converter Bricks, Open/Enclosed BAQ SERIES, 1/4 BRICK, UP TO 200W MECHANICAL PCB LAYOUT CONNECTION PIN # SINGLE 1 -Vin 2 REM 3 +Vin 4 GND 5 -S 6 TRIM 7 +S 8 +Vo Note: * Unit is mm(inch). DERATING CURVE www.pairuigroup.com EFFICIENCY CURVE Page: 4/5 Date: 02/09/2014 DC-DC Converter Bricks, Open/Enclosed BAQ SERIES, 1/4 BRICK, UP TO 200W NOTES RECOMMENDED TEST AND APPLICATION CIRCUIT 1. TVS&FUSE be helpful with over voltage protection and inrush limiting. Recommended FUSE better be 1.5~2times of the rated current . 2. The input filter capacitor C6 could select the aluminum electrolytic capacitors or tantalum capacitors, and the withstand voltage should be greater than the highest input voltage. Recommended capacitor should be between 22μF~100μF. 3. C1,C2 for the input filter capacitor,0.1~1μF high-frequency ceramics capacitor or chip capacitor are recommended. The withstand voltage of output filter C5, C7 should be greater than the highest output voltage. Recommended capacitor of C7 better within 100μF and C5 connected with the chip to reduce the input voltage peak, recommended 0.1~1μF high-frequency ceramics capacitor or chip capacitor. www.pairuigroup.com Page: 5/5 Date: 02/09/2014