CHENMKO ENTERPRISE CO.,LTD CHUMA11PT SURFACE MOUNT Dual Digital Silicon Transistor VOLTAGE 50 Volts CURRENT 100 mAmpere APPLICATION * Switching circuit, Inverter, Interface circuit, Driver circuit. FEATURE * Small surface mounting type. (SC-88A/SOT-353) * High current gain. * Suitable for high packing density. * * * * SC-88A/SOT353 Low colloector-emitter saturation. High saturation current capability. Two CHDTA143Z chips in a package. Built in bias resistor(R1=4.7kΩ, Typ. ) (1) (5) 0.65 1.2~1.4 2.0~2.5 0.65 (2) (3) 0.15~0.35 1.15~1.35 0.8~1.1 0.08~0.15 0~0.1 0.1 Min. CIRCUIT 3 2 2.15~2.45 R1 R1 R2 1 R2 4 5 SC-88A/SOT353 Dimensions in millimeters LIMITING VALUES In accordance with the Absolute Maximum Rating System (IEC 60134). SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT VCC Supply voltage − -50 V VIN Input voltage -30 +5 V − -100 − -100 − 150 mW O C IO DC Output current IC(Max.) Tamb ≤ 25 OC, Note 1 mA PTOT Total power dissipation TSTG Storage temperature −55 +150 TJ Junction temperature − 150 O C Thermal resistance − 140 O C/W RθJ-S junction - soldering point Note 1. Transistor mounted on an FR4 printed-circuit board. 2004-04 RATING CHARACTERISTIC ( CHUMA11PT ) CHARACTERISTICS Tamb = 25 °C unless otherwise speciÞed. SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT VIoff) Input off voltage IO=-100uA; VCC=-5.0V Input on voltage IO=-5mA; VO=-0.3V -0.5 − − VI(on) VO(on) Output voltage IO=-5mA; II=-0.25mA − II Input current VI=-5V − -0.1 − IC(off) Output current VI=0V; VCC=-50V − − hFE DC current gain IO=-10mA; VO=-5.0V 80 − − R1 Input resistor 3.29 4.7 6.11 KΩ R2/R1 fT Resistor ratio Transition frequency 8 − 10 250 12 − MHz Note 1.Pulse test: tp≤300uS; δ≤0.02. IC=-5mA, VCE=-10.0V f=100MHz = − − -1.3 V -0.3 V -1.8 mA -0.5 uA V RATING CHARACTERISTIC CURVES ( CHUMA11PT ) Typical Electrical Characteristics Fig.1 Input voltage vs. output current (ON characteristics) VO=−0.3V −50 OUTPUT CURRENT : Io (A) INPUT VOLTAGE : VI(on) (V) −100 Fig.2 Output current vs. input voltage (OFF characteristics) −20 −10 −5 Ta=−40°C 25°C 100°C −2 −1 −500m −200m −100m −100µ −200µ −500µ −1m −2m −10m −5m −1m −500µ −100µ −50µ −20µ −10µ −5µ Fig.3 DC current gain vs. output current 200 VO=−5V Ta=100°C 25°C −40°C 100 50 20 10 5 2 −1.0 −1.5 −2.0 −2.5 −3.0 Fig.4 Output voltage vs. output current OUTPUT VOLTAGE : VO(on) (V) DC CURRENT GAIN : GI 1k −0.5 INPUT VOLTAGE : VI(off) (V) OUTPUT CURRENT : IO (A) 500 Ta=100°C 25°C −40°C −200µ −2µ −1µ 0 −5m −10m −20m −50m −100m VCC=−5V −2m −1 −500m −200m lO/lI=20 Ta=100°C 25°C −40°C −100m −50m −20m −10m −5m −2m 1 −100µ −200µ −500µ −1m −2m −5m −10m −20m −50m −100m OUTPUT CURRENT : IO (A) −1m −100µ −200µ −500µ −1m −2m −5m −10m −20m −50m −100m OUTPUT CURRENT : IO (A)