AD AD9822 Complete 14-bit ccd/cis signal processor Datasheet

Complete 14-Bit
CCD/CIS Signal Processor
AD9822
FEATURES
GENERAL DESCRIPTION
14-bit 15 MSPS ADC
No missing codes guaranteed
3-channel operation up to 15 MSPS
1-channel operation up to 12.5 MSPS
Correlated double sampling
1–6× programmable gain
±350 mV programmable offset
Input clamp circuitry
Internal voltage reference
Multiplexed byte-wide output (8 + 6 format)
3-wire serial digital interface
3 V/5 V digital I/O compatibility
28-Lead SOIC or SSOP
Low power CMOS: 385 mW (typ)
Power-down mode: <1 mW
The AD9822 is a complete analog signal processor for CCD
imaging applications. It features a 3-channel architecture designed
to sample and condition the outputs of trilinear color CCD
arrays. Each channel consists of an input clamp, correlated double
sampler (CDS), offset DAC, and programmable gain amplifier
(PGA) multiplexed to a high performance 14-bit ADC.
The CDS amplifiers may be disabled for use with sensors such
as contact image sensors (CIS) and CMOS active pixel sensors,
which do not require CDS.
The 14-bit digital output is multiplexed into an 8-bit output
word that is accessed using two read cycles. The internal
registers are programmed through a 3-wire serial interface and
provide adjustment of the gain, offset, and operating mode.
The AD9822 operates from a single 5 V power supply,
consumes 385 mW of power typically, and is packaged in a
28-lead SOIC or SSOP.
APPLICATIONS
Flatbed document scanners
Film scanners
Digital color copiers
Multifunction peripherals
FUNCTIONAL BLOCK DIAGRAM
VINR
AVSS
CML
CDS
CAPT
CAPB
AVDD
CDS
14:8
MUX
8
MUX
REGISTER
PGA
INPUT
CLAMP
BIAS
14
DOUT
CONFIGURATION
REGISTER
6
CDSCLK1
14-BIT
ADC
3:1
MUX
9-BIT
DAC
OFFSET
OEB
BAND GAP
REFERENCE
PGA
CDS
DRVSS
AD9822
9-BIT
DAC
VINB
DRVDD
PGA
9-BIT
DAC
VING
AVSS
9
RED
GREEN
BLUE
RED
GREEN
BLUE
CDSCLK2
SCLK
DIGITAL
CONTROL
INTERFACE
GAIN
REGISTERS
SLOAD
SDATA
OFFSET
REGISTERS
ADCCLK
00623-001
AVDD
Figure 1.
Rev. B
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.326.8703
© 2005 Analog Devices, Inc. All rights reserved.
AD9822
TABLE OF CONTENTS
Specifications..................................................................................... 3
1-Channel CDS Mode ............................................................... 12
Analog Specifications................................................................... 3
1-Channel SHA Mode ............................................................... 12
Digital Specifications ................................................................... 4
Internal Register Descriptions.................................................. 13
Timing Specifications .................................................................. 5
Circuit Operation ........................................................................... 15
Absolute Maximum Ratings............................................................ 6
Analog Inputs—CDS Mode ...................................................... 15
Thermal Characteristics .............................................................. 6
External Input Coupling Capacitors........................................ 15
ESD Caution.................................................................................. 6
Analog Inputs—SHA Mode...................................................... 16
Pin Configuration and Function Descriptions............................. 7
Programmable Gain AmplifierS (PGA) .................................. 16
Terminology ...................................................................................... 8
Applications..................................................................................... 17
Functional Description .................................................................. 12
Circuit and Layout Recommendations ................................... 17
3-Channel CDS Mode................................................................ 12
Outline Dimensions ....................................................................... 18
3-Channel SHA Mode................................................................ 12
Ordering Guide .......................................................................... 18
REVISION HISTORY
2/05—Rev. A to Rev. B
Changes to Format .............................................................Universal
Changes to Ordering Guide .......................................................... 18
Updated Outline Dimensions ....................................................... 18
12/99—Rev. 0 to Rev. A
Rev. B | Page 2 of 20
AD9822
SPECIFICATIONS
ANALOG SPECIFICATIONS
TMIN to TMAX, AVDD = 5 V, DRVDD = 5 V, CDS mode, fADCCLK = 15 MHz, fCDSCLK1 = fCDSCLK2 = 5 MHz, PGA gain = 1, unless otherwise noted.
Table 1.
Parameter
MAXIMUM CONVERSION RATE
3-Channel Mode with CDS
1-Channel Mode with CDS
ACCURACY (ENTIRE SIGNAL PATH)
ADC Resolution
Integral Nonlinearity (INL)
INL @ 6 MHz
Differential Nonlinearity (DNL)
DNL @ 6 MHz
No Missing Codes
No Missing Codes @ 6 MHz
Offset Error
Gain Error
ANALOG INPUTS
Input Signal Range1
Allowable Reset Transient1
Input Limits2
Input Capacitance
Input Bias Current
AMPLIFIERS
PGA Gain at Minimum
PGA Gain at Maximum
PGA Gain Resolution2
PGA Gain Monotonicity
Programmable Offset at Minimum
Programmable Offset at Maximum
Programmable Offset Resolution
Programmable Offset Monotonicity
NOISE AND CROSSTALK
Total Output Noise @ PGA Minimum
Total Output Noise @ PGA Maximum
Channel-to-Channel Crosstalk @ 6 MHz
POWER SUPPLY REJECTION
AVDD = 5 V ± 0.25 V
DIFFERENTIAL VREF (@ 25°C)
CAPT to CAPB (2 V ADC Full-Scale Range)
TEMPERATURE RANGE
Operating
Storage
POWER SUPPLIES
AVDD
DRVDD
OPERATING CURRENT
AVDD
DRVDD
Power-Down Mode Current
Min
Typ
Max
15
12.5
−1.0
14
−240
−1.4
MSPS
MSPS
14
−17.0/+3.5
−10.5/+1.5
−0.65/+0.75
−0.6/+0.65
14
−19
+3.5
+1.1
+200
+6.9
2.0
1.0
AVSS − 0.3
AVDD + 0.3
10
10
1
5.7
64
Guaranteed
−350
+350
512
Guaranteed
mV
mV
Steps
LSB rms
LSB rms
LSB
0.9
% FSR
1.0
1.06
V
+70
+150
°C
°C
5.25
5.25
V
V
5.0
5.0
73
4
150
Rev. B | Page 3 of 20
V p-p
V
V
pF
nA
0.063
0
−65
4.75
3.0
Bits
LSB
LSB
LSB
LSB
Bits
Bits
mV
% FSR
V/V
V/V
Steps
1.5
6.0
<1
0.94
Unit
mA
mA
µA
AD9822
Parameter
POWER DISSIPATION
3-Channel Mode
3-Channel Mode @ 6 MHz
1-Channel Mode
1-Channel Mode @ 6 MHz
1
Min
Typ
Max
Unit
385
335
300
250
450
410
mW
mW
mW
mW
Linear input signal range is from 2 V to 4 V when the CCD’s reference level is clamped to 4 V by the AD9822’s input clamp.
2
00623-002
4V SET BY INPUT CLAMP (3V OPTION ALSO AVAILABLE)
1V TYP
RESET TRANSIENT
2V p-p MAX INPUT SIGNAL RANGE
The PGA gain is approximately linear-in-dB and follows the equation: Gain =
[
5.7
⎡ 63 − G ⎤
1 + 4 .7 ⎢
⎥
⎣ 63 ⎦
] where G is the register value. See Figure 15.
DIGITAL SPECIFICATIONS
TMIN to TMAX, AVDD = 5 V, DRVDD = 5 V, CDS mode, fADCCLK = 15 MHz, fCDSCLK1 = fCDSCLK2 = 5 MHz, CL = 10 pF, unless otherwise noted.
Table 2.
Parameter
LOGIC INPUTS
High Level Input Voltage
Low Level Input Voltage
High Level Input Current
Low Level Input Current
Input Capacitance
LOGIC OUTPUTS
High Level Output Voltage
Low Level Output Voltage
High Level Output Current
Low Level Output Current
Symbol
Min
VIH
VIL
IIH
IIL
CIN
2.0
VOH
VOL
IOH
IOL
4.5
Rev. B | Page 4 of 20
Typ
Max
0.8
10
10
10
0.1
50
50
Unit
V
V
µA
µA
pF
V
V
µA
µA
AD9822
TIMING SPECIFICATIONS
TMIN to TMAX, AVDD = 5 V, DRVDD = 5 V.
Table 3.
Parameter
CLOCK PARAMETERS
3-Channel Pixel Rate
1-Channel Pixel Rate
ADCCLK Pulse Width
CDSCLK1 Pulse Width
CDSCLK2 Pulse Width
CDSCLK1 Falling to CDSCLK2 Rising
ADCCLK Falling to CDSCLK2 Rising
CDSCLK2 Rising to ADCCLK Rising
CDSCLK2 Falling to ADCCLK Falling
CDSCLK2 Falling to CDSCLK1 Rising
ADCCLK Falling to CDSCLK1 Rising
Aperture Delay for CDS Clocks
SERIAL INTERFACE
Maximum SCLK Frequency
SLOAD to SCLK Setup Time
SCLK to SLOAD Hold Time
SDATA to SCLK Rising Setup Time
SCLK Rising to SDATA Hold Time
SCLK Falling to SDATA Valid
DATA OUTPUT
Output Delay
Three-State to Data Valid
Output Enable High to Three-State
Latency (Pipeline Delay)
Symbol
Min
tPRA
tPRB
tADCLK
tC1
tC2
tC1C2
tADC2
tC2ADR
tC2ADF
tC2C1
tADC1
tAD
67
80
30
10
10
0
0
0
30
30
0
fSCLK
tLS
tLH
tDS
tDH
tRDV
10
10
10
10
10
10
tOD
tDV
tHZ
Rev. B | Page 5 of 20
Typ
40
40
2
Max
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
MHz
ns
ns
ns
ns
ns
8
10
10
3 (Fixed)
ns
ns
ns
Cycles
AD9822
ABSOLUTE MAXIMUM RATINGS
Table 4.
Parameter
VIN, CAPT, CAPB
Digital Inputs
AVDD
DRVDD
AVSS
Digital Outputs
Junction Temperature
Storage Temperature
Lead Temperature
(10 sec)
With
Respect
To
AVSS
AVSS
AVSS
DRVSS
DRVSS
DRVSS
THERMAL CHARACTERISTICS
Min
−0.3
−0.3
−0.5
−0.5
−0.3
−0.3
−65
Max
AVDD + 0.3
AVDD + 0.3
+6.5
+6.5
+0.3
DRVDD + 0.3
150
+150
300
Unit
V
V
V
V
V
V
°C
°C
°C
28-Lead 300 Mil SOIC
θJA = 71.4°C/W
θJC = 23°C/W
28-Lead 5.3 mm SSOP
θJA = 109°C/W
θJC = 39°C/W
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or other
conditions above those indicated in the operational sections of
this specification is not implied. Exposure to absolute maximum
ratings for extended periods may affect device reliability.
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. B | Page 6 of 20
AD9822
CDSCLK1 1
28
AVDD
CDSCLK2 2
27
AVSS
ADCCLK 3
26
VINR
OEB 4
25
OFFSET
DRVDD 5
24
VING
23
CML
22
VINB
D6 8
21
CAPT
D5 9
20
CAPB
D4 10
19
AVSS
D3 11
18
AVDD
D2 12
17
SLOAD
D1 13
16
SCLK
(LSB) D0 14
15
SDATA
DRVSS 6
(MSB) D7 7
AD9822
TOP VIEW
(Not to Scale)
00623-003
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
Figure 2. Pin Configuration
Table 5. Pin Function Descriptions
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
1
Mnemonic
CDSCLK1
CDSCLK2
ADCCLK
OEB
DRVDD
DRVSS
D7 (MSB)
D6
D5
D4
D3
D2
D1
D0 (LSB)
SDATA
SCLK
SLOAD
AVDD
AVSS
CAPB
CAPT
VINB
CML
VING
OFFSET
VINR
AVSS
AVDD
Type1
DI
DI
DI
DI
P
P
DO
DO
DO
DO
DO
DO
DO
DO
DI/DO
DI
DI
P
P
AO
AO
AI
AO
AI
AO
AI
P
P
Description
CDS Reference Level Sampling Clock.
CDS Data Level Sampling Clock.
ADC Sampling Clock.
Output Enable, Active Low.
Digital Output Driver Supply.
Digital Output Driver Ground.
Data Output MSB. ADC DB13 High Byte, ADC DB5 Low Byte.
Data Output. ADC DB12 High Byte, ADC DB4 Low Byte.
Data Output. ADC DB11 High Byte, ADC DB3 Low Byte.
Data Output. ADC DB10 High Byte, ADC DB2 Low Byte.
Data Output. ADC DB9 High Byte, ADC DB1 Low Byte.
Data Output. ADC DB8 High Byte, ADC DB0 Low Byte.
Data Output. ADC DB7 High Byte, Don’t Care Low Byte.
Data Output LSB. ADC DB6 High Byte, Don’t Care Low Byte.
Serial Interface Data Input/Output.
Serial Interface Clock Input.
Serial Interface Load Pulse.
5 V Analog Supply.
Analog Ground.
ADC Bottom Reference Voltage Decoupling.
ADC Top Reference Voltage Decoupling.
Analog Input, Blue Channel.
Internal Bias Level Decoupling.
Analog Input, Green Channel.
Clamp Bias Level Decoupling.
Analog Input, Red Channel.
Analog Ground.
5 V Analog Supply.
Type: AI = Analog Input, AO = Analog Output, DI = Digital Input, DO = Digital Output, P = Power.
Rev. B | Page 7 of 20
AD9822
TERMINOLOGY
Integral Nonlinearity (INL)
Integral nonlinearity error refers to the deviation of each
individual code from a line drawn from zero scale through
positive full scale. The point used as zero scale occurs ½ LSB
before the first code transition. Positive full scale is defined as a
level 1 ½ LSB beyond the last code transition. The deviation is
measured from the middle of each particular code to the true
straight line.
Differential Nonlinearity (DNL)
An ideal ADC exhibits code transitions that are exactly 1 LSB
apart. DNL is the deviation from this ideal value; therefore,
every code must have a finite width. No missing codes
guaranteed to 14-bit resolution indicates that all 16384 codes,
respectively, must be present over all operating ranges.
Offset Error
The first ADC code transition should occur at a level ½ LSB
above the nominal zero-scale voltage. The offset error is the
deviation of the actual first code transition level from the ideal
level.
Gain Error
The last code transition should occur for an analog value
1 ½ LSB below the nominal full-scale voltage. Gain error is the
deviation of the actual difference between the first and last code
transitions and the ideal difference between the first and last
code transitions.
Input Referred Noise
The rms output noise is measured using histogram techniques.
The ADC output codes’ standard deviation is calculated in LSB
and converted to an equivalent voltage, using the relationship
1 LSB = 4 V/16384 = 244 mV. The noise is then referred to the
input of the AD9822 by dividing by the PGA gain.
Channel-to-Channel Crosstalk
In an ideal 3-channel system, the signal in one channel will not
influence the signal level of another channel. The channel-tochannel crosstalk specification is a measure of the change that
occurs in one channel as the other two channels are varied. In
the AD9822, one channel is grounded and the other two
channels are exercised with full-scale input signals. The
change in the output codes from the first channel is measured
and compared with the result when all three channels are
grounded. The difference is the channel-to-channel crosstalk,
stated in LSB.
Aperture Delay
The time delay that occurs from when a sampling edge is
applied to the AD9822 until the actual sample of the input
signal is held. Both CDSCLK1 and CDSCLK2 sample the input
signal during the transition from high to low; therefore, the
aperture delay is measured from each clock’s falling edge to the
instant the actual internal sample is taken.
Power Supply Rejection
It specifies the maximum full-scale change that occurs from
the initial value when the supplies are varied over the
specified limits.
Rev. B | Page 8 of 20
AD9822
ANALOG
INPUTS
tAD
PIXEL N (R, G, B)
PIXEL
(N + 2)
PIXEL (N + 1)
tAD
tC1
tC2C1
tPRA
CDSCLK1
tC1C2
tC2
tC2ADF
CDSCLK2
tADCLK
tADC2
tADC1
tC2ADR
ADCCLK
R (N– 2) G (N– 2) G (N– 2) B (N– 2) B (N– 2) R (N– 1) R (N– 1) G (N– 1) G (N– 1) B (N– 1) B (N– 1)
HIGH
BYTE
LOW
BYTE
HIGH
BYTE
LOW
BYTE
HIGH
BYTE
LOW
BYTE
HIGH
BYTE
LOW
BYTE
HIGH
BYTE
LOW
BYTE
R (N)
R (N)
G (N)
G (N)
HIGH
BYTE
LOW
BYTE
HIGH
BYTE
LOW
BYTE
00623-004
tOD
tADCLK
OUTPUT
DATA
D<7:0>
Figure 3. 3-Channel CDS Mode Timing
ANALOG
INPUTS
PIXEL N
tAD
PIXEL (N + 1)
PIXEL (N + 2)
tAD
tC2C1
tC1
tPRB
CDSCLK1
tC1C2
tC2
tADC1
CDSCLK2
tC2ADR
tADCLK
tADCLK
tOD
PIXEL
(N – 4)
PIXEL
(N – 4)
PIXEL
(N – 3)
PIXEL
(N – 3)
PIXEL
(N – 2)
PIXEL
(N – 2)
HIGH BYTE
LOW BYTE
HIGH BYTE
LOW BYTE
HIGH BYTE
LOW BYTE
Figure 4. 1-Channel CDS Mode Timing
Rev. B | Page 9 of 20
00623-005
ADCCLK
OUTPUT
DATA
D<7:0>
tC2ADF
AD9822
PIXEL N (R, G, B)
PIXEL (N + 1)
tAD
ANALOG
INPUTS
tPRA
tC2
tC2ADF
CDSCLK2
tADCLK
tC2ADR
tADC2
ADCCLK
OUTPUT
DATA
D<7:0>
R (N– 2) G (N– 2) G (N– 2) B (N– 2) B (N– 2) R (N– 1) R (N– 1) G (N– 1) G (N– 1) B (N– 1) B (N– 1)
HIGH
BYTE
LOW
BYTE
HIGH
BYTE
LOW
BYTE
HIGH
BYTE
LOW
BYTE
HIGH
BYTE
LOW
BYTE
HIGH
BYTE
LOW
BYTE
R (N)
R (N)
G (N)
G (N)
HIGH
BYTE
LOW
BYTE
HIGH
BYTE
LOW
BYTE
00623-006
tOD
tADCLK
Figure 5. 3-Channel SHA Mode Timing
PIXEL N
tAD
ANALOG
INPUTS
tPRB
tC2
CDSCLK2
tC2ADR
tADCLK
tADCLK
tOD
PIXEL (N – 4)
PIXEL (N – 4)
PIXEL (N – 3)
PIXEL (N – 3)
PIXEL (N – 2)
PIXEL (N – 2)
HIGH BYTE
LOW BYTE
HIGH BYTE
LOW BYTE
HIGH BYTE
LOW BYTE
Figure 6. 1-Channel SHA Mode Timing
Rev. B | Page 10 of 20
00623-007
ADCCLK
OUTPUT
DATA
D<7:0>
tC2ADF
AD9822
ADCCLK
tOD
HIGH BYTE
DB13–DB6
LOW BYTE
DB5–DB0
PIXEL N
PIXEL N
LOW
BYTE
N+2
LOW
BYTE
N+1
HIGH BYTE
N+1
tHZ
HIGH
BYTE
N+3
tDV
00623-008
OUTPUT
DATA
<D7:D0>
tOD
OEB
Figure 7. Digital Output Data Timing
SDATA
R/Wb
A2
A1
A0
XX
tDH
XX
XX
D8
D7
D6
D5
D4
D3
D2
D1
D0
tDS
SCLK
tLH
00623-009
tLS
SLOAD
Figure 8. Serial Write Operation Timing
SDATA
R/Wb
A2
tDH
A1
A0
XX
XX
tDS
XX
D8
D7
D6
D5
D4
D3
D2
D1
D0
tRDV
SCLK
tLH
00623-010
tLS
SLOAD
Figure 9. Serial Read Operation Timing
Rev. B | Page 11 of 20
AD9822
FUNCTIONAL DESCRIPTION
The AD9822 can be operated in four different modes: 3-channel
CDS mode, 3-channel SHA mode, 1-channel CDS mode, and
1-channel SHA mode. Each mode is selected by programming
the configuration register through the serial interface. For more
information on CDS or SHA mode operation, see the Circuit
Operation section.
3-CHANNEL CDS MODE
In 3-channel CDS mode, the AD9822 simultaneously samples
the red, green, and blue input voltages from the CCD outputs.
The sampling points for each CDS are controlled by CDSCLK1
and CDSCLK2 (see Figure 10 and Figure 11). CDSCLK1’s
falling edge samples the reference level of the CCD waveform,
and CDSCLK2’s falling edge samples the data level of the CCD
waveform. Each CDS amplifier outputs the difference between
the CCD’s reference and data levels. The output voltage of each
CDS amplifier is then level-shifted by an offset DAC. The
voltages are scaled by the three PGAs before being multiplexed
through the 14-bit ADC. The ADC sequentially samples the
PGA outputs on the falling edges of ADCCLK.
The offset and gain values for the red, green, and blue channels
are programmed using the serial interface. The order in which
the channels are switched through the multiplexer is selected by
programming the MUX register.
Timing for this mode is shown in Figure 3. It is recommended
that the falling edge of CDSCLK2 occur coincident with or
before the rising edge of ADCCLK. However, this is not
required to satisfy the minimum timing constraints. The rising
edge of CDSCLK2 should not occur before the previous falling
edge of ADCCLK, as shown by tADC2. The output data latency is
three clock cycles.
The input signal is sampled with respect to the voltage applied
to the OFFSET pin (see Figure 12). With the OFFSET pin
grounded, a 0 V input corresponds to the ADC’s zero-scale
output. The OFFSET pin may also be used as a coarse offset
adjust pin. A voltage applied to this pin is subtracted from the
voltages applied to the red, green, and blue inputs in the first
amplifier stage of the AD9822. The input clamp is disabled in
this mode. For more information, see the Circuit Operation
section.
Timing for this mode is shown in Figure 5. CDSCLK1
should be grounded in this mode. Although not required,
it is recommended that the falling edge of CDSCLK2 occur
coincident with or before the rising edge of ADCCLK. The
rising edge of CDSCLK2 should not occur before the previous
falling edge of ADCCLK, as shown by tADC2. The output data
latency is three ADCCLK cycles.
The offset and gain values for the red, green, and blue channels
are programmed using the serial interface. The order in which
the channels are switched through the multiplexer is selected by
programming the MUX register.
1-CHANNEL CDS MODE
This mode operates in the same way as the 3-channel CDS
mode. The difference is that the multiplexer remains fixed in
this mode; therefore, only the channel specified in the MUX
register is processed.
Timing for this mode is shown in Figure 4.
1-CHANNEL SHA MODE
3-CHANNEL SHA MODE
This mode operates in the same way as the 3-channel SHA
mode, except the multiplexer remains stationary. Only the
channel specified in the MUX register is processed.
In 3-channel SHA mode, the AD9822 simultaneously samples
the red, green, and blue input voltages. The sampling point is
controlled by CDSCLK2. CDSCLK2’s falling edge samples the
input waveforms on each channel. The output voltages from the
three SHAs are modified by the offset DACs and then scaled by
the three PGAs. The outputs of the PGAs are then multiplexed
through the 14-bit ADC. The ADC sequentially samples the
PGA outputs on the falling edges of ADCCLK.
The input signal is sampled with respect to the voltage applied
to the OFFSET pin. With the OFFSET pin grounded, a 0 V input
corresponds to the ADC’s zero-scale output. The OFFSET pin
may also be used as a coarse offset adjust pin. A voltage applied
to this pin is subtracted from the voltages applied to the red,
green, and blue inputs in the first amplifier stage of the AD9822.
The input clamp is disabled in this mode. For more information,
see the Circuit Operation section.
Timing for this mode is shown in Figure 6. CDSCLK1 should be
grounded in this mode of operation.
Rev. B | Page 12 of 20
AD9822
INTERNAL REGISTER DESCRIPTIONS
Table 6. Internal Register Map
Register Name
Configuration
MUX
Red PGA
Green PGA
Blue PGA
Red Offset
Green Offset
Blue Offset
Address
A2
A1
A0
0
0
0
0
0
1
0
1
0
0
1
1
1
0
0
1
0
1
1
1
0
1
1
1
D8
0
0
0
0
0
MSB
MSB
MSB
D7
0
RGB/BGR
0
0
0
D6
VREF
Red
0
0
0
Data Bits
D
D4
3Ch/1Ch
CDS On
Green
Blue
MSB
MSB
MSB
D3
Clamp
0
D2
Pwr Dn
0
D1
0
0
D0
0
0
LSB
LSB
LSB
LSB
LSB
LSB
Configuration Register
The Configuration Register controls the AD9822’s operating mode and bias levels. Bits D8, D1, and D0 should always be set low. Bit D7
sets the full-scale voltage range of the AD9822’s ADC to either 4 V (high) or 2 V (low). Bit D6 controls the internal voltage reference. If the
AD9822’s internal voltage reference is used, this bit is set high. Setting Bit D6 low disables the internal voltage reference, allowing an
external voltage reference to be used. Bit D5 configures the AD9822 for either the 3-channel (high) or 1-channel (low) mode of operation.
Setting Bit D4 high enables the CDS mode of operation and setting this bit low enables the SHA mode of operation. Bit D3 sets the dc bias
level of the AD9822’s input clamp. This bit should always be set high for the 4 V clamp bias, unless a CCD with a reset feedthrough
transient exceeding 2 V is used. If the 3 V clamp bias level is used, the peak-to-peak input signal range to the AD9822 is reduced to 3 V
maximum. Bit D2 controls the power-down mode. Setting Bit D2 high places the AD9822 into a very low power “sleep” mode. All register
contents are retained while the AD9822 is in the power-down state.
Table 7. Configuration Register Settings
D8
Set to 0
1
D7
Set to 0
D6
Internal VREF
1 = Enabled1
0 = Disabled
D5
No. of Channels
1 = 3-Ch Mode1
0 = 1-Ch Mode
D4
CDS Operation
1 = CDS Mode1
0 = SHA Mode
D3
Input Clamp Bias
1 = 4 V1
0=3V
D2
Power-Down
1 = On
0 = Off (Normal)1
D1
Set to 0
D0
Set to 0
Power-on default value.
MUX Register
The MUX register controls the sampling channel order in the AD9822. Bits D8, D3, D2, D1, and D0 should always be set low. Bit D7 is
used when operating in 3-channel mode. Setting Bit D7 high sequences the MUX to sample the red channel first, then the green channel,
and then the blue channel. When in this mode, the CDSCLK2 pulse always resets the MUX to sample the red channel first (see Figure 3).
When Bit D7 is set low, the channel order is reversed to blue first, green second, and red third. The CDSCLK2 pulse always resets the
MUX to sample the blue channel first. Bits D6, D5, and D4 are used when operating in 1-channel mode. Bit D6 is set high to sample the
red channel. Bit D5 is set high to sample the green channel. Bit D4 is set high to sample the blue channel. The MUX remains stationary
during 1-channel mode.
Table 8. MUX Register Settings
D8
Set to 0
1
D7
3-Channel Select
1 = R-G-B1
0 = B-G-R
D6
1-Channel Select
1 = RED1
0 = Off
D5
1-Channel Select
1 = GREEN
0 = Off1
D4
1-Channel Select
1 = BLUE
0 = Off1
Power-on default value.
Rev. B | Page 13 of 20
D3
Set to 0
D2
Set to 0
D1
Set to 0
D0
Set to 0
AD9822
PGA Gain Registers
There are three PGA registers for individually programming the gain in the red, green, and blue channels. Bits D8, D7, and D6 in each
register must be set low, and Bits D5 through D0 control the gain range in 64 increments. See Figure 15 for the PGA gain vs. the PGA
register code. The coding for the PGA registers is straight binary, with an all 0s word corresponding to the minimum gain setting (1×)
and an all 1s word corresponding to the maximum gain setting (5.7×).
Table 9. PGA Gain Register Settings
D8
Set to 0
0
0
D7
Set to 0
0
0
D6
Set to 0
0
0
D5
MSB
0
0
D4
0
0
0
0
0
0
1
1
1
1
1
D3
0
0
D2
0
0
•
•
•
1
1
D1
0
0
0
0
D0
LSB
01
1
1
1
1
1
0
1
Gain (V/V)
1.0
1.013
•
•
•
5.4
5.7
Gain (dB)
0.0
0.12
•
•
•
14.6
15.1
Power-on default value.
Offset Registers
There are three PGA registers for individually programming the offset in the red, green, and blue channels. Bits D8 through D0 control
the offset range from −350 mV to +350 mV in 512 increments. The coding for the offset registers is sign magnitude, with D8 as the sign
bit. Table 10 shows the offset range as a function of the Bits D8 through D0.
Table 10. Offset Register Settings
D8 (MSB)
0
0
D7
0
0
D6
0
0
D5
0
0
D4
0
0
0
1
1
1
0
0
1
0
0
1
0
0
1
0
0
1
1
1
1
1
1
D3
0
0
•
•
•
1
0
0
•
•
•
1
D2
0
0
D1
0
0
D0 (LSB)
01
1
1
0
0
1
0
0
1
0
1
1
1
1
Power-on default value.
Rev. B | Page 14 of 20
Offset (mV)
0
+1.2
•
•
•
+350
0
−1.2
•
•
•
−350
AD9822
CIRCUIT OPERATION
ANALOG INPUTS—CDS MODE
EXTERNAL INPUT COUPLING CAPACITORS
Figure 10 shows the analog input configuration for the CDS
mode of operation. Figure 11 shows the internal timing for the
sampling switches. The CCD reference level is sampled when
CDSCLK1 transitions from high to low, opening S1. The CCD
data level is sampled when CDSCLK2 transitions from high to
low, opening S2. S3 is then closed, generating a differential
output voltage representing the difference between the two
sampled levels.
The recommended value for the input coupling capacitors is
0.1 µF. While it is possible to use a smaller capacitor, this larger
value is chosen for several reasons:
• Signal Attenuation: The input coupling capacitor creates a
capacitive divider with a CMOS integrated circuit’s input
capacitance, attenuating the CCD signal level. CIN should be
large relative to the IC’s 10 pF input capacitance in order to
minimize this effect.
The input clamp is controlled by CDSCLK1. When CDSCLK1 is
high, S4 closes and the internal bias voltage is connected to the
analog input. The bias voltage charges the external 0.1 µF input
capacitor, level-shifting the CCD signal into the AD9822’s input
common-mode range. The time constant of the input clamp is
determined by the internal 5 kΩ resistance and the external
0.1 µF input capacitance.
AD9822
S1
VINR
2pF
CML
CCD SIGNAL
CIN
0.1µF
S3
5kΩ
CML
S2
AVDD
OFFSET
1µF
1.7kΩ
4V
0.1µF
• Sampling Errors: The internal 2 pF sample capacitors have a
“memory” of the previously sampled pixel. There is a charge
redistribution error between CIN and the internal sample
capacitors for larger pixel-to-pixel voltage swings. As the
value of CIN is reduced, the resulting error in the sampled
voltage increases. With a CIN value of 0.1 µF, the charge
redistribution error is less than 1 LSB for a full-scale, pixel-topixel voltage swing.
INPUT CLAMP LEVEL
2.2kΩ IS SELECTED IN THE
CONFIGURATION
REGISTER.
6.9kΩ
3V
00362-011
S4
+
2pF
• Linearity: Some of the input capacitance of a CMOS IC is
junction capacitance, which varies nonlinearly with applied
voltage. If the input coupling capacitor is too small, the
attenuation of the CCD signal varies nonlinearly with signal
level. This degrades the system linearity performance.
Figure 10. CDS Mode Input Configuration (All Three Channels are Identical)
S1, S4 CLOSED
S1, S4 CLOSED
S1, S4 OPEN
S2 CLOSED
CDSCLK2
S2 OPEN
Q3
(INTERNAL)
S3 OPEN
S2 CLOSED
S3 CLOSED
S3 CLOSED
00623-012
CDSCLK1
Figure 11. CDS Mode Internal Switch Timing
Rev. B | Page 15 of 20
AD9822
ANALOG INPUTS—SHA MODE
AD9822
Figure 12 shows the analog input configuration for the SHA
mode of operation. Figure 13 shows the internal timing for the
sampling switches. The input signal is sampled when CDSCLK2
transitions from high to low, opening S1. The voltage on the
OFFSET pin is also sampled on the falling edge of CDSCLK2,
when S2 opens. S3 is then closed, generating a differential
output voltage representing the difference between the sampled
input voltage and the OFFSET voltage. The input clamp is
disabled during SHA mode operation.
VINR
RED
SHA
BLUE-OFFSET
VINB
BLUE
VREF FROM
CIS MODULE
AVDD
OFFSET
0.1µF
00623-015
R2
2pF
CML
S2
S3
2pF
RED
Figure 14. SHA Mode Used with External DC Offset
CML
PROGRAMMABLE GAIN AMPLIFIERS (PGA)
VING
GREEN
BLUE
00623-013
VINB
The AD9822 uses one PGA for each channel. Each PGA has a
gain range from 1× (0 dB) to 5.8× (15.5 dB), adjustable in
64 steps. Figure 15 shows the PGA gain as a function of the
PGA register code. Although the gain curve is approximately
linear-in-dB, the gain in V/V varies nonlinearly with register
code, following the equation
Figure 12. SHA Mode Input Configuration (All Three Channels are Identical)
S1, S2 CLOSED
Gain =
S1, S2 CLOSED
S3 CLOSED
S3 CLOSED
S3 OPEN
00623-014
S1, S2 OPEN
where G is the decimal value of the gain register contents and
varies from 0 to 63.
GAIN (dB)
Figure 13. SHA Mode Internal Switch Timing
Figure 14 shows how the OFFSET pin may be used in a CIS
application for coarse offset adjustment. Many CIS signals have
dc offsets ranging from several hundred millivolts to more than
1 V. By connecting the appropriate dc voltage to the OFFSET
pin, the CIS signal is restored to 0. After the large dc offset is
removed, the signal can be scaled using the PGA to maximize
the ADC’s dynamic range.
5.7
⎡ 63 − G ⎤
1 + 4.7 ⎢
⎥
⎣ 63 ⎦
15
5.7
12
5.0
9
4.0
6
3.0
3
2.0
1.0
0
0
4
8
12 16 20 24 28 32 36 40 44 48 52 56 60 63
PGA REGISTER VALUE (Decimal)
Figure 15. PGA Gain Transfer Function
Rev. B | Page 16 of 20
GAIN (V/V)
OFFSET
OPTIONAL DC OFFSET
(OR CONNECT TO GND)
Q3
(INTERNAL)
GREEN-OFFSET
DC OFFSET
S1
INPUT SIGNAL
CDSCLK2
SHA
VING
00623-016
VINR
RED-OFFSET
GREEN
R1
AD9822
SHA
AD9822
APPLICATIONS
CDSCLK2 should occur coincident with or before the rising
edge of ADCCLK (see Figure 3 through Figure 6 for timing).
All 0.1 µF decoupling capacitors should be located as close as
possible to the AD9822 pins. When operating in single-channel
mode, the unused analog inputs should be grounded.
CIRCUIT AND LAYOUT RECOMMENDATIONS
Figure 16 shows the recommended circuit configuration for
3-channel CDS mode operation. The recommended input
coupling capacitor value is 0.1 µF (see the Circuit Operation
section). A single ground plane is recommended for the
AD9822. A separate power supply may be used for DRVDD,
the digital driver supply, but this supply pin should still be
decoupled to the same ground plane as the rest of the AD9822.
The loading of the digital outputs should be minimized, either
by using short traces to the digital ASIC or by using external
digital buffers. To minimize the effect of digital transients
during major output code transitions, the falling edge of
Figure 17 shows the recommended circuit configuration for
3-channel SHA mode. All of the above considerations also apply
for this configuration, except that the analog input signals are
directly connected to the AD9822 without the use of coupling
capacitors. The analog input signals must already be dc-biased
between 0 V and 2 V (see the Circuit Operation section).
0.1µF
5V
5V/3V
1
CDSCLK1
AVDD 28
2
CDSCLK2
AVSS 27
3
ADCCLK
4
OEB
5
DRVDD
6
DRVSS
7
D7 (MSB)
0.1µF
DATA OUTPUTS
RED INPUT
3
0.1µF
0.1µF
GREEN INPUT
0.1µF
VINR 26
BLUE INPUT
OFFSET 25
VING 24
AD9822
0.1µF
0.1µF
1.0µF
CML 23
0.1µF
VINB 22
8
D6
CAPT 21
9
D5
CAPB 20
10
D4
AVSS 19
11
D3
AVDD 18
12
D2
SLOAD 17
13
D1
14
D0 (LSB)
0.1µF
+
10µF
0.1µF
0.1µF
SCLK 16
5V
00623-017
CLOCK INPUTS
SDATA 15
8
3
SERIAL INTERFACE
Figure 16. Recommended Circuit Configuration, 3-Channel CDS Mode
5V
RED INPUT
5V/3V
0.1µF
1
CDSCLK1
AVDD 28
2
CDSCLK2
AVSS 27
3
ADCCLK
4
OEB
5
DRVDD
6
DRVSS
7
D7 (MSB)
8
D6
CAPT 21
9
D5
CAPB 20
GREEN INPUT
VINR 26
BLUE INPUT
OFFSET 25
AD9822
VING 24
0.1µF
VINB 22
AVSS 19
11 D3
AVDD 18
12 D2
SLOAD 17
14 D0 (LSB)
0.1µF
CML 23
10 D4
13 D1
DATA OUTPUTS
0.1µF
0.1µF
+
10µF
0.1µF
SCLK 16
5V
SDATA 15
8
0.1µF
3
SERIAL INTERFACE
00623-018
CLOCK INPUTS
3
Figure 17. Recommended Circuit Configuration, 3-Channel SHA Mode (Analog Inputs Sampled with Respect to Ground)
Rev. B | Page 17 of 20
AD9822
OUTLINE DIMENSIONS
18.10 (0.7126)
17.70 (0.6969)
28
15
7.60 (0.2992)
7.40 (0.2913)
1
10.65 (0.4193)
10.00 (0.3937)
14
2.65 (0.1043)
2.35 (0.0925)
0.75 (0.0295)
× 45°
0.25 (0.0098)
0.30 (0.0118)
0.10 (0.0039)
COPLANARITY
0.10
8°
1.27 (0.0500) 0.51 (0.0201) SEATING 0.33 (0.0130) 0°
BSC
PLANE
0.31 (0.0122)
0.20 (0.0079)
1.27 (0.0500)
0.40 (0.0157)
COMPLIANT TO JEDEC STANDARDS MS-013AE
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN
Figure 18. 28-Lead Standard Small Outline Package [SOIC]
Wide Body (R-28)
Dimensions shown in millimeters and (inches)
10.50
10.20
9.90
28
15
5.60
5.30
5.00
8.20
7.80
7.40
14
1
PIN 1
1.85
1.75
1.65
2.00 MAX
COPLANARITY
0.10
0.25
0.09
0.05 MIN
0.65
BSC
0.38
0.22
SEATING
PLANE
8°
4°
0°
0.95
0.75
0.55
COMPLIANT TO JEDEC STANDARDS MO-150AH
Figure 19. 28-Lead Shrink Small Outline Package [SSOP]
(RS-28)
Dimensions shown in millimeters
ORDERING GUIDE
Model
AD9822JR
AD9822JRRL
AD9822JRS
AD9822JRSRL
AD9822JRSZ1
AD9822JRSZRL1
1
Temperature Range
0°C to 70°C
0°C to 70°C
0°C to 70°C
0°C to 70°C
0°C to 70°C
0°C to 70°C
Package Description
28-Lead SOIC
28-Lead SOIC
28-Lead SSOP
28-Lead SSOP
28-Lead SSOP
28-Lead SSOP
Z = Pb-free part.
Rev. B | Page 18 of 20
Package Options
R-28
R-28
RS-28
RS-28
RS-28
RS-28
AD9822
NOTES
Rev. B | Page 19 of 20
AD9822
NOTES
© 2005 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
C00623–0–2/05(B)
Rev. B | Page 20 of 20
Similar pages