EGP10A THRU EGP10G GLASS PASSIVATED FAST EFFICIENT RECTIFIER Forward Current - 1.0 Ampere D * Reverse Voltage - 50 to 400 Volts FEATURES P A T E N T E DO-204AL 1.0 (25.4) MIN. 0.107 (2.7) 0.080 (2.0) DIA. ® 0.205 (5.2) 0.160 (4.1) ♦ Plastic package has Underwriters Laboratories Flammability Classification 94V-0 ♦ Glass passivated cavity-free junction ♦ Superfast recovery time for high efficiency ♦ Low forward voltage, high current capability ♦ Low leakage current ♦ High surge current capability ♦ High temperature metallurgically bonded construction ♦ High temperature soldering guaranteed: 300°C/10 seconds, 0.375" (9.5mm) lead length, 5 lbs. (2.3kg) tension 1.0 (25.4) MIN. 0.034 (0.86) 0.028 (0.71) DIA. Dimensions in inches and (millimeters) * Glass Encapsulation technique is covered by Patent No. 3,996,602, brazed-lead assembly to Patent No. 3,930,306 MECHANICAL DATA Case: JEDEC DO-204AL molded plastic over glass body Terminals: Plated axial leads, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Mounting Position: Any Weight: 0.012 ounce, 0.3 gram MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS EGP 10A EGP 10B EGP 10C EGP 10D EGP 10F EGP 10G UNITS Maximum repetitive peak reverse voltage VRRM 50 100 150 200 300 400 Volts Maximum RMS voltage VRMS 35 70 105 140 210 280 Volts Maximum DC blocking voltage VDC 50 100 150 200 300 400 Volts Maximum average forward rectified current 0.375" (9.5mm) lead length at TA=55°C I(AV) 1.0 Amp Peak forward surge current 8.3ms single half sine-wave superimposed on rated load IFSM 30.0 Amps Maximum instantaneous forward voltage at 1.0A 0.95 1.25 Volts IR 5.0 100 µA Maximum reverse recovery time (NOTE 1) trr 50.0 ns Typical junction capacitance (NOTE 2) CJ Maximum DC reverse current at rated DC blocking voltage TA=25°C TA=125°C VF Typical thermal resistance (NOTE 3) Operating junction and storage temperature range 15.0 pF RΘJA 50.0 °C/W TJ, TSTG -65 to +150 °C NOTES: (1) Reverse recovery test conditions: IF=0.5A, IR=1.0A, Irr=0.25A (2) Measured at 1.0 MHZ and applied reverse voltage of 4.0 Volts (3) Thermal resistance from junction to ambient at 0.375" (9.5mm) lead length, P.C.B. mounted 4/98 22.0 FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 1.0 PEAK FORWARD SURGE CURRENT, AMPERES FIG. 1 - MAXIMUM FORWARD CURRENT DERATING CURVE RESISTIVE OR INDUCTIVE LOAD 0.375” (9.5mm) LEAD LENGTH 0.5 0 0 25 50 75 100 125 150 175 30 TJ=TJ max. 8.3ms SINGLE HALF SINE WAVE (JEDEC Method) 25 20 15 10 5.0 0 1 AMBIENT TEMPERATURE, °C 100 10 NUMBER OF CYCLES AT 60 HZ FIG. 3 -TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 50 FIG. 4 - TYPICAL REVERSE CHARACTERISTICS INSTANTANEOUS REVERSE LEAKAGE CURRENT, MICROAMPERES INSTANTANEOUS FORWARD FORWARD CURRENT, AMPERES 1,000 PULSE WIDTH=300µs 1% DUTY CYCLE 10 TJ=150°C TJ=25°C 1 0.1 100 TJ=150°C 10 TJ=100°C 1 0.1 TJ=25°C 0 0 EGP10A - EGP10D EGP10F & EGP10G 0.01 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE, % 1.8 INSTANTANEOUS FORWARD VOLTAGE, VOLTS FIG. 6 - TYPICAL TRANSIENT THERMAL IMPEDANCE FIG. 5 - TYPICAL JUNCTION CAPACITANCE 70 TJ=25°C f=1.0 MHZ Vsig=50mVp-p 60 50 40 30 20 10 0 0.1 EGP10A - EGP10D EGP10F & EGP10G 1 10 REVERSE VOLTAGE, VOLTS 100 TRANSIENT THERMAL IMPEDANCE, °CW 100 JUNCTION CAPACITANCE, pF AVERAGE FORWARD RECTIFIED CURRENT, AMPERES RATINGS AND CHARACTERISTICS CURVES EGP10A THRU EGP10G 10 1 0.1 0.01 0.1 1 t, PULSE DURATION, sec. 10 100