SITI DM13H Maximum output voltage: 17v Datasheet

DM13H
Version
Issue Date
File Name
Total Pages
: A.004
: 2014/09/16
: SP-DM13H-A.004.doc
: 26
16-Channel Constant Current LED Driver
with Error Detection
新竹市科學園區展業一路 9 號 4 樓之 3
SILICON TOUCH TECHNOLOGY INC.
9-7F-1, Prosperity Road I, Science Based Industrial Park,
Hsin-Chu, Taiwan 300, R.O.C.
Tel：886-3-5645656
Fax：886-3-5645626
DM13H
DM13H
16-Channel Constant Current LED Driver
With Error Detection
General Description
DM13H is a 16-channel constant-current sink driver specifically designed for LED
display applications. The device incorporates shift registers, data latches, and constant
current circuitry on the silicon CMOS chip. The maximum output current of each channel is
set by a single external resistor. Overall output currents can be adjusted by a 7-bit serial
shift-in data. Its built-in LED open/short detection, output channels short to GND detection
help users to detect LED failures, outputs short. The thermal alarm and shutdown functions
provide the over-temperature protection.
Features
z
16-Channel Constant-current outputs: 3mA to 90mA adjustable by one external resistor
z
Maximum output voltage: 17V
z
Maximum cascade clock frequency: 25MHz
z
7-bit linear global brightness control
z
Built-in LED open/short detection: Real-time detection or Smart detection
z
Built-in Outputs short to GND detection: Real-time or Smart detection
z
Fast detecting response: 100ns (min.)
z
Over temperature protection:
Alarm (junction temperature > 130°C)
Shutdown (junction temperature > 170°C)
z
Sleep mode (sleep current : 5uA)
z
In-rush current control
z
Schmitt trigger input
z
Power supply voltage: 3.0V to 5.5V
z
Package pin assignment compatible to conventional LED drivers (DM134B/5B,DM13C)
Applications
z
LED Variable Message Signs (VMS) System
z
Indoor/Outdoor LED Video Display
Packages
SOP24, SSOP24, TSSOP24E, SOP24B, QFN24
16-Channel Constant Current LED Driver with Error Detection
Version:A.004
未經授權而逕予重製、複製、使用或公開本文件，行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Page 1
DM13H
Block Diagram
16-Channel Constant Current LED Driver with Error Detection
Version:A.004
未經授權而逕予重製、複製、使用或公開本文件，行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Page 2
DM13H
Pin Connection (Top View)
SOP24 / SSOP24 / TSSOP24E / SOP24B
GND
DAI
CLK
LAT
OUT0
OUT1
OUT2
OUT3
OUT4
OUT5
OUT6
OUT7
1
2
3
4
5
6
7
8
9
10
11
12
24
23
22
21
20
19
18
17
16
15
14
13
QFN24
VCC
REXT
DAO
EN
OUT15
OUT14
OUT13
OUT12
OUT11
OUT10
OUT9
OUT8
Pin Description
PIN No.
PIN NAME
FUNCTION
SOP24 / SSOP24 / TSSOP24E / SOP24B: 1
QFN24: 22
GND
Ground terminal.
SOP24 / SSOP24 / TSSOP24E / SOP24B: 2
QFN24: 23
DAI
Serial data input terminal.
SOP24 / SSOP24 / TSSOP24E / SOP24B: 3
QFN24: 24
CLK
Synchronous clock input terminal for serial data
transfer.
Data is sampled at the rising edge of CLK.
SOP24 / SSOP24 / TSSOP24E / SOP24B: 4
QFN24: 1
LAT
Input terminal of data strobe.
Data on shift register goes through at the rising
edge (edge trigger). Otherwise, data is latched.
SOP24 / SSOP24 / TSSOP24E / SOP24B: 5~20
QFN24: 2~17
OUT0~15 Sink constant-current outputs (open-drain).
SOP24 / SSOP24 / TSSOP24E / SOP24B: 21
QFN24: 18
EN
Output enable terminal:
‘H’ for all outputs are turned off ,
‘L’ for all outputs are active.
SOP24 / SSOP24 / TSSOP24E / SOP24B: 22
QFN24: 19
DAO
Serial data output terminal.
SOP24 / SSOP24 / TSSOP24E / SOP24B: 23
QFN24: 20
REXT
External resistors connected between REXT and
GND for output current value setting.
SOP24 / SSOP24 / TSSOP24E / SOP24B: 24
QFN24: 21
VCC
Supply voltage terminal.
16-Channel Constant Current LED Driver with Error Detection
Version:A.004
未經授權而逕予重製、複製、使用或公開本文件，行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Page 3
DM13H
Equivalent Circuit of Inputs and Outputs
1.CLK, DAI, LAT , EN terminals ( Schmitt Trigger Input )
2. DAO terminals
16-Channel Constant Current LED Driver with Error Detection
Version:A.004
未經授權而逕予重製、複製、使用或公開本文件，行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Page 4
DM13H
Maximum Ratings (Ta=25°C, Tj(max) = 150°C)
SYMBOL
RATING
UNIT
Supply Voltage
CHARACTERISTIC
VCC
-0.3 ~ 7.0
V
Input Voltage
VIN
-0.3 ~ VCC+0.3
V
Output Current
IOUT
90
mA
Output Voltage
VOUT
-0.3 ~ 17
V
Input Clock Frequency
FCKI
30
MHz
GND Terminal Current
IGND
1500
mA
Power Dissipation
Thermal Resistance
1.5 (SSOP24)
PD
W
2.8 (TSSOP24)
85 (SSOP24)
Rth(j-a)
°C/W
45 (TSSOP24E)
Operating Temperature
Top
-40 ~ 85
°C
Storage Temperature
Tstg
-55 ~ 150
°C
Recommended Operating Condition
CHARACTERISTIC
Supply Voltage
SYMBOL
CONDITION
MIN.
TYP.
MAX.
UNIT
VCC
⎯
3.0
⎯
5.5
V
⎯
⎯
17
V
*1
Output Voltage
VOUT
IO
OUTn, VCC=5V
3
⎯
90
Output Current
IOH
VOH = VCC – 0.2 V
⎯
⎯
+1.5
IOL
VOL = 0.2 V
⎯
⎯
-1.5
Input Voltage
Input Clock Frequency
VIH
VIL
FCKI
Driver Off
VCC = 3.3 V ~ 5V
Single Chip Operation
Cascade Operation
0.7VCC
⎯
VCC
0.0
⎯
0.3VCC
⎯
⎯
15
⎯
⎯
30
⎯
LAT Pulse Width
tw LAT
CLK Pulse Width
tw CLK
13
⎯
⎯
EN Pulse Width
tw EN
50
⎯
⎯
Set-up Time for DAI
tsetup(D)
10
⎯
⎯
Hold Time for DAI
thold(D)
10
⎯
⎯
Set-up Time for LAT
tsetup(L)
10
⎯
⎯
Hold Time for LAT
thold(L)
10
⎯
⎯
LAT Pulse Width
tw LAT
15
⎯
⎯
CLK Pulse Width
tw CLK
13
⎯
⎯
VCC = 5.0V
tw EN
50
⎯
⎯
Set-up Time for DAI
tsetup(D)
12
⎯
⎯
Hold Time for DAI
thold(D)
8
⎯
⎯
Set-up Time for LAT
tsetup(L)
8
⎯
⎯
Hold Time for LAT
thold(L)
12
⎯
⎯
EN Pulse Width
*1
VCC =3.3V
mA
V
MHz
ns
ns
The driver output voltage including any overshoot stress has to be compliant with the maximum voltage (17V).
16-Channel Constant Current LED Driver with Error Detection
Version:A.004
未經授權而逕予重製、複製、使用或公開本文件，行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Page 5
DM13H
Electrical Characteristics (VCC = 5.0 V, Ta = 25°C unless otherwise noted)
CHARACTERISTIC
SYMBOL
CONDITION
MIN.
TYP.
MAX.
Input Voltage “H” Level
VIH
CMOS logic level
0.7VCC
⎯
VCC
Input Voltage “L” Level
VIL
CMOS logic level
GND
⎯
0.3VCC
Output Leakage Current
IOL
VOH = 17 V
⎯
⎯
+1
VOL
IOL = -1.5 mA
⎯
⎯
0.2
VOH
IOH= 1.5 mA
VCC-0.2
⎯
⎯
⎯
⎯
±4
%
⎯
⎯
±6
%
Output Voltage (S-OUT)
Output Current Skew
*1
(Channel-to-Channel)
IOL1
Output Current Skew
*2
(Chip-to-Chip)
IOL2
VOUT = 1.0 V
Rrext = 3.9 KΩ
UNIT
V
uA
V
Output Voltage Regulation
% / VOUT
Rrext = 3.9 KΩ
VOUT = 1 V ~ 3 V
⎯
±0.1
±0.5
Supply Voltage Regulation
% / VCC
Rrext = 3.9 KΩ
⎯
±1
±4
Differential Linearity
DNL
Rrext = 3.9 KΩ
⎯
±1.2
Output Voltage Short to GND,
LED Open Detection Threshold
V(od)
output turns on
⎯
0.1
⎯
V
SV = ”H”
⎯
VCC
⎯
V
SV = ”L”
⎯
5/6VCC
⎯
V
⎯
130
⎯
⎯
170
⎯
⎯
170
⎯
⎯
LED Short Detection Threshold*3
(output turns on)
T(170)
Thermal Shutdown Threshold
Supply Current
LSB
V(sd)
T(130)
Thermal Threshold
%/V
junction temperature
T(sht)
IDD(off)
power on
all pins are open
unless VCC and GND
⎯
1.2
IDD(off)
Rrext = 3.9 KΩ
all outputs turn off
⎯
7
IDD(on)
Rrext = 3.9 KΩ
all outputs turn on
⎯
7.6
IDD(off)
Rrext = 820 Ω
all outputs turn off
⎯
27.5
IDD(on)
Rrext = 820 Ω
all outputs turn on
⎯
30
IDD(sleep)
Sleep current
⎯
5
(Input signal is static)
⎯
°C
mA
⎯
uA
*1
Channel-to-channel skew is defined as the ratio between (any Iout – average Iout) and average Iout,
where average Iout = (Imax + Imin) / 2.
*2
Chip-to-Chip skew is defined as the range into which any output current of any IC falls.
*3
LED short detection voltage level default value is VCC , refer to Page 12 for level selection.
16-Channel Constant Current LED Driver with Error Detection
Version:A.004
未經授權而逕予重製、複製、使用或公開本文件，行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Page 6
DM13H
Switching Characteristics (VCC = 5.0V, Ta = 25°C unless otherwise noted)
CHARACTERISTIC
SYMBOL
CONDITION
MIN.
TYP.
MAX.
14
26
36
VIH = VCC
19
31
41
VIL = GND
15
19
23
19
31
41
19
32
41
16
20
24
4.5
10
18
4.5
10
18
EN -to-OUT0
Propagation Delay
LAT -to-OUT0
(‘L to ‘H’)
tpLH
CLK-to-DAO
EN -to-OUT0
Propagation Delay
LAT -to-OUT0
(‘H’ to ‘L’)
Rrext = 3.9 KΩ
tpHL
VL = 5.0 V
CLK-to-DAO
Output Current Rise Time
tor
RL = 0.18 KΩ
CL = 13 pF
Output Current Fall Time
tof
Output Delay Time (OUT(n)-to-OUT(n+1))
tod
0.5
3
5.5
Detection Response
tdet
20
100
120
UNIT
ns
Switching Characteristics (VCC = 3.3V, Ta = 25°C unless otherwise noted)
CHARACTERISTIC
SYMBOL
CONDITION
MIN.
TYP.
MAX.
16
36
46
VIH = VCC
21
37
47
VIL = GND
18
22
26
19
35
41
19
37
41
19
23
27
7.5
14
21
7.5
14
21
EN -to-OUT0
Propagation Delay
LAT -to-OUT0
(‘L to ‘H’)
tpLH
CLK-to-DAO
EN -to-OUT0
Propagation Delay
LAT -to-OUT0
(‘H’ to ‘L’)
Rrext = 3.9 KΩ
tpHL
VL = 5 V
CLK-to-DAO
Output Current Rise Time
tor
RL = 0.18 KΩ
CL = 13 pF
Output Current Fall Time
tof
Output Delay Time (OUT(n)-to-OUT(n+1))
tod
0.7
3
6.5
Detection Response
tdet
20
100
120
16-Channel Constant Current LED Driver with Error Detection
Version:A.004
未經授權而逕予重製、複製、使用或公開本文件，行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
UNIT
ns
Page 7
DM13H
Timing Diagram
1. CLK-DAI, DAO
twDCK
DCK
50%
t setup(D)
DAI
twDCK
50%
50%
50%
thold(D)
50%
50%
DAO
50%
50%
tpLH
tpHL
2. CLK- LAT
CLK
50%
50%
t hold(L)
t setup(L)
LAT
50%
50%
twLAT
3. LAT -OUT0
50%
50%
LAT
t or
tof
90%
90%
50%
OUT0
50%
10%
10%
t pLH
(current)
t pHL
4. EN -OUT0
t wEN
EN
50%
50%
tof
tor
90%
90%
50%
50%
10%
OUT0
t pLH
(current)
10%
t pHL
5. OUTn+1-OUTn
OUTn+1
(current)
50%
tod
OUTn
(current)
50%
16-Channel Constant Current LED Driver with Error Detection
Version:A.004
未經授權而逕予重製、複製、使用或公開本文件，行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Page 8
DM13H
Constant-Current Output
Constant-current value of each output channel is set by an external resistor connected
between the REXT pin and GND. Varying the resistor value can adjust the current scale
ranging from 3mA to 90mA. The reference voltage of REXT terminal (Vrext) is
approximately 1.23V. The output current value is calculated by the following equation:
90
80
Iout (mA) ~
IOUT(mA)
70
60
V rext (V)
× 65
Rrext (KΩ)
50
40
30
20
10
0
1
2
3
4
5
6
Rext (K)
7
8
9
10
In order to obtain a good performance of constant-current output, a suitable output voltage
is necessary. Users can get related information about the minimum output voltage below.
100
90
80
IOUT(mA)
70
60
50
40
30
20
10
0
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 1.2 1.4 1.6 1.8 2 2.2 2.4 2.6 2.8 3
VOUT(V)
16-Channel Constant Current LED Driver with Error Detection
Version:A.004
未經授權而逕予重製、複製、使用或公開本文件，行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Page 9
DM13H
Serial Data Interface
DM13H includes a flexible data transfer interface. The data can be transferred from DAI
pin to the shift registers at the rising edge of CLK. After all data are clocked in, a rising edge
of the LAT signal can transfer the serial data to the data latches (Edge trigger). The serial
data format can be 16-bit or 10-bit wide, depending on the operating mode of the device.
Operation Mode
DM13H has two operating modes depending on the combination of CLK and LAT
signals. The table below shows the available operating modes. For normal operation (SD
mode), the data width of shift register is 16-bit, which is used to set 16 bits serial-in image
data. The sequence of the combination of CLK and LAT explains in following pages is
used to change the operation mode. If there are four triggering clock pulses (CLK) with high
level latch ( LAT ), DM13H will change to command data input mode (CD mode) at falling
edge of the latch pulse ( LAT ) then user can make ten triggering clock pulses to set 7-bit
GBC data (default value after power-on is 7’b1000000), 1-bit voltage level selection of short
detection (default value after power-on is 1’b1) and 1-bit sleep control data (default value is
1’b0)
OPERATION MODE
SHIFT REGISTER
Serial-in Data Input Mode (SD mode)
16-bit
Command Data Input Mode (CD mode)
10-bit
16-Channel Constant Current LED Driver with Error Detection
Version:A.004
未經授權而逕予重製、複製、使用或公開本文件，行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Page 10
DM13H
SD Mode Data Format
MSB
15
14
13
12
11
OUT15
OUT14
OUT13
OUT12
OUT11
‧‧‧
4
3
2
1
LSB
0
OUT4
OUT3
OUT2
OUT1
OUT0
Shift-in first
When DM13H operates at SD mode, the serial-in data (DAI) will be clocked into 16-bit
shift register synchronized on the rising edge of the clock (CLK). The data ‘1’ represents the
corresponding current output ‘ON’, while the data ‘0’ stands for ‘OFF’. The data will be
transferred into the 16 bit latch synchronized on the rising edge of the strobe signal ( LAT );
otherwise, the output data won’t be changed. The latch pulse should be sent after the falling
edge of the last clock within a frame data.
0
1
2
3
13
14
15
0
1
CLK
0
1
high
DAI
DAO
2
low
0
previous data
1
Tsetup (L)
high
LAT
low
0
EN
1
on
OUT 0
off
(current)
on
OUT 1
off
(current)
on
OUT 2
off
(current)
.
.
.
.
.
.
on
OUT12
off
(current)
on
OUT13
off
(current)
on
OUT14
off
(current)
on
OUT15
off
(current)
16-Channel Constant Current LED Driver with Error Detection
Version:A.004
未經授權而逕予重製、複製、使用或公開本文件，行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Page 11
DM13H
CD Mode Data Format
a. Global Brightness Control
DM13H offers a convenient way to fine tune the whole chip output currents for the
uniformity of brightness between modules, ICs or the accomodation to ambient light. To
further adjust the current level linearly, the system shall enter the CD MODE and then shift
in 7-bit GBC data code through DAI pin. The MSB should be shifted-in first. Take the input
code. G[6:0]= (MSB)1001011(LSB) for example. The new current is then equal to the base
current multiplied by the ratio (26 + 23 + 21 + 20 + 1) 128 . The 7-bit data won’t be changed until the
next new data is latched. Note that the default code 7’b1000000 exists in chip memory
when power on, so the output current is equal to the half of base current.
b. Short detection voltage level selection
DM13H provides 2 voltage levels in coordination with LED short detection on system.
VCC voltage level is the default value while power-on. DAO will send an error signal = H if
the output voltage is greater than a respectively predetermined threshold value.
SV
Short Voltage
0
5/6 * VCC
1
VCC (default)
c. Sleep mode
When SLP=1, DM13H will enter sleep mode, all outputs turn off and the IDD of DM13H
will drop down to less than 5uA. This function is especially designed for battery or solar
powered system.
16-Channel Constant Current LED Driver with Error Detection
Version:A.004
未經授權而逕予重製、複製、使用或公開本文件，行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Page 12
DM13H
Error Detection
DM13H includes Real-time and Smart detection mode for LED open/short and driver
outputs short to GND detection. It can be set as six types which are showing as following
table.
Detection Type
Real time LED Open Detection
Detection Operation
CLK rising edge x1, with LAT =H
Real time Output Short to GND Detection CLK rising edge x2, with LAT =H
Real time LED Short Detection
CLK rising edge x3, with LAT =H
Smart LED Open Detection
CLK rising edge x1, with LAT =H
then LAT falling edge x2 with CLK=H
Smart Output Short to GND Detection
CLK rising edge x2, with LAT =H
then LAT falling edge x2 with CLK=H
Smart LED Short Detection
CLK rising edge x3, with LAT =H
then LAT falling edge x2 with CLK=H
Selection of detection types is a collocation of CLK and LAT . After detection executed,
the error report will be saved in the particular shift register and could be retrieved from
serial-out(DAO) data.
For Real-Time LED open/short detections, it’s necessary to set the image data of the
particular output channel as ‘1’. The serial-out data is ‘0’ in the LED normal state, and the
serial-out data will be ‘1’ while a LED failure has occurred. If the image data is written to “0”
or the output terminal is inactive (EN =H), it will not execute any detection process for the
corresponding channel. Therefore, the serial-data will remain as “0”.
For Real-Time Output Short to GND detection type, set the image data of the particular
output channel to ‘0’, outputs’ state will be identified from DAO as above. In output normal
state, the serial-out data is ‘0’, but if the serial-out data is ‘1’ then a DM13H output voltage
lower than 0.1V. If the image data of particular channel is ‘1’, no detection will be executed
for the corresponding channel, and the serial-out data will be ’0’. Otherwise, If output enable
terminal is active (EN =’L’), the serial-out data will be ’0’.
DM13H specializes in fast detection response, 100ns minima. Moreover, it offers multi
selections like Real-Time monitor and Smart detection. Accordingly, it is more flexible and
well adapted to the system requirements.
16-Channel Constant Current LED Driver with Error Detection
Version:A.004
未經授權而逕予重製、複製、使用或公開本文件，行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Page 13
DM13H
a. Normal operation
When DM13H operates at normal operation (Latch only) the DAO pin will send out the
original serial-in data not the error message.
SD mode
1
DAI
J [2]
J [1]
J [0]
14
15
16
Don＇care
t
L[15]
L[14]
1
2
L[ 0 ]
Don＇care
t
M[15 ]
M[14 ]
1
2
M[13]
0
Normal operation
16
3
high
CLK
low
high
LAT
l ow
1
DAO
I [1]
I [2]
J [14]
J [15]
L [15 ]
L [14 ]
L [13 ]
0
OUT0
(current )
on
Fr ame Data I
Fr ame Data J
Frame Data L
off
b. LED Open/Short Detection(Real-time)
Set one CLK rising edge with LAT =‘H’ to operate Open Real-Time detection. Each
channel will be identified as a LED open failure when there is a current passing through the
output but the voltage is below 0.1V.
SD Mode
DAI
LED Open
Real Time
Detection Mode
SD Mode
1
J [2]
J [1]
J [0]
Don＇care
t
L[15]
L[14]
14
15
16
1
1
2
L[ 0 ]
Don＇care
t
M[15 ]
M[14 ]
M[13 ]
1
2
3
0
16
CLK
High
Low
1
LAT
0
tDET
DAO
OUT0
(current )
High
I [2]
I [1]
I [0]
E [15 ]
E [14 ]
L [15 ]
L [14 ]
L [13 ]
Low
On
Fr ame Data I
Frame Data L
Fr ame Data J
Off
16-Channel Constant Current LED Driver with Error Detection
Version:A.004
未經授權而逕予重製、複製、使用或公開本文件，行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Page 14
DM13H
Set three CLK rising edges with LAT =‘H’ to operate Short Real-Time detection. A LED
short failure will be identified when the output channel is on and the output voltage is higher
VCC.
LED Short
Real Time
Detection Mode
SD Mode
SD Mode
1
DAI
J [2]
J [1]
Don＇care
t
J [0]
L [15]
L[14]
L[ 0 ]
Don＇care
t
M [15]
M[14]
M[13]
0
14
15
16
1
2
3
1
2
16
1
2
3
CLK
High
Low
1
LAT
0
tDET
High
DAO
I [2]
I [0]
I [1]
E [15 ]
E [14 ]
L [15 ]
L[14]
L[13]
Low
OUT0
(current )
On
Frame Data I
Frame Data L
Frame Data J
Off
With the above operating principle, the controller could continuously retrieve LED
status from serial-out(DAO) then compare with the last frame date one by one . Once there
is any serial-out data at ’1’ be retrieved, it pinpoints the channel with failed LED. Since the
process is ongoing and without shifting between image and detection mode, it does not
interrupt the image data flow and the output display. This is known as “Real-Time Monitor”.
c. LED Open/Short Detection (Smart Detection)
DM13H also specially provides another ”smart” detection method. In Smart detection
mode, DM13H will automatically turns on all output channels with Iout=50uA until the next
rising edge of the CLK pulse. After the rising edge of CLK, the output current will return to
original state. Notice that enable control (EN ) won’t affect smart detection result.
Set one CLK rising edge with LAT =‘H’ then two LAT falling edges with CLK is ‘H’ to
operate Open Smart detection. Each channel will be identified as a LED open failure when
there is a current passing through the output but the voltage is below 0.1V.
LED Open
Smart Detection Mode
SD Mode
DAI
J [2]
J [1]
J [0]
14
15
16
SD Mode
Don＇care
t
L[15]
L[14]
1
2
L[ 0 ]
Don＇care
t
1
M[15]
M[14]
M[13 ]
1
2
3
0
1
16
CLK
High
Low
1
2
1
LAT
0
tDET
DAO
OUT0
(current )
High
I [2]
I [1]
I [0]
E [15 ]
E [14 ]
L [15 ]
L [14 ]
L [13 ]
Low
On
Frame Data I
Frame Data J
Frame Data L
Off
16-Channel Constant Current LED Driver with Error Detection
Version:A.004
未經授權而逕予重製、複製、使用或公開本文件，行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Page 15
DM13H
Set three CLK rising edges with LAT =‘H’ then two LAT falling edges with CLK is ‘H’ to
operate Short Smart detection. A LED short failure will be identified when the output channel
is off and there is a current passing through the output but the voltage is above VCC.
LED Short
Smart Detection Mode
SD Mode
DAI
J [2]
J [1]
J [0]
14
15
16
SD Mode
Don＇care
t
L[15]
L[14]
1
2
L[ 0 ]
Don＇care
t
1
M[15 ]
M[14 ]
M[13 ]
1
2
3
0
1
2
3
16
High
CLK
Low
1
2
1
LAT
0
tDET
DAO
I [2]
I [1]
I [0]
E [15 ]
E [14 ]
L [15 ]
L [14 ]
High
L [13 ]
Low
OUT0
Frame Data I
(current )
Frame
On
Frame Data L
Data J
Off
The error report of LED status will be retrieved from DAO. Once there is any serial-out
data at ’1’ be retrieved, controller can counts clocks to identify the locations of fail LED. The
impression of “invisible failure detection” is achievable because of less data clock-in cycle
and small current during detection to avoid a flash. After Smart detection, DM13H will return
to normal operation until next detection.
d. Outputs Short to GND Detection (Real-Time/Smart)
This error detection mode could detect the failure of IC and PCB. If IC output pins are
burned-out or output pins on PCB layout are short to ground, the voltage of IC output pins
would be pulled to low voltage. It will make LEDs turn on all the time. Therefore, DM13H
would determine the failure of IC output pins when the output voltage is below 0.1V. For the
duration of output short to GND smart detection, the output would be turned off
automatically and pulled high to VDD no matter channel is on or off.
Set two CLK rising edges with LAT =‘H’ to operate Output Short to GND Real-Time
detection. An output short failure will be identified when the output turn off but the voltage is
below 0.1V.
SD Mode
Output Short to GND
Real Time
Detection Mode
SD Mode
1
DAI
J [2]
J [1]
J [0]
14
15
16
Don＇care
t
L[15]
L[14]
1
2
L[ 0 ]
Don＇care
t
M[15]
M[14]
M[13]
1
2
3
0
1
2
16
CLK
High
Low
1
LAT
0
tDET
High
DAO
OUT0
(current )
I [2]
I [1]
I [0]
E [15 ]
E [14 ]
L [15 ]
L [14 ]
L [13 ]
Low
On
Fr ame Data I
Fr ame Data L
Fr ame Data J
Off
16-Channel Constant Current LED Driver with Error Detection
Version:A.004
未經授權而逕予重製、複製、使用或公開本文件，行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Page 16
DM13H
Set two CLK rising edges with LAT =‘H’ then sending two LAT falling edges with CLK
is ‘H’ to operate Output Short to GND Smart detection. DM13H will force all outputs to turn
off automatically, and start to detect output short error until the next rising edge of CLK pulse.
After the rising edge of CLK, the output current will return to original value. After the
detection, device will return to Normal Operation. Notice that enable control (EN ) won’t
affect smart detection result.
Output Short to GND
Smart Detection Mode
SD Mode
DAI
SD Mode
1
J [2]
J [1]
J [0]
14
15
16
Don＇care
t
L[15]
L[14]
1
2
L[ 0 ]
Don＇care
t
M[15 ]
M[14 ]
M[13 ]
1
2
3
0
1
2
16
CLK
High
Low
1
2
1
LAT
0
tDET
DAO
OUT0
(current )
High
I [2]
I [1]
I [0]
E [15 ]
E [14 ]
L [15 ]
L [14]
L [13 ]
Low
On
Frame Data I
Frame Data L
Frame Data J
Off
Outputs Delay
Large in-rush currents will occur when the system activates all the outputs at once. To
prevent this effect, a constant unit of delay between outputs is built-in DM13H. All outputs
are divided into four groups and each group contains four outputs. For example, OUT0 ~
OUT3 form the group1; OUT4 ~ OUT7 form the group2. There is no delay between every
group. But each output delay between channels in a group is 3ns @VDD=3.3V (typical).
OUT 0, 4, 8,12
OUT 1, 5, 9,13
OUT 2, 6, 10,14
OUT 3, 7, 11,15
tod tod tod
16-Channel Constant Current LED Driver with Error Detection
tod tod tod
Version:A.004
未經授權而逕予重製、複製、使用或公開本文件，行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Page 17
DM13H
Thermal Alarm and Shutdown
DM13H provides a temperature error detection circuit for thermal alarm and shutdown
protection. When junction temperature of the IC exceeds 130℃, the thermal flag(T130) will
be serial-out in the CD mode. If no cooling measures to reduce the temperature(by system),
the junction temperature might continue to rise. Once it reaches to 170℃, DM13H will turn
off all outputs. When the junction temperature is lower than 130℃, DM13H will restart
automatically. Operation in the over-temperature situation( > 130℃) for a long time may
cause chip damage permanently.
Thermal Flag
Description
130℃ temperature flag
T130
"H" : Temp ≧ 130℃,
“ L” : Temp < 130℃
170℃ temperature flag
T170
"H" : Temp ≧ 170℃,
“L” : Temp < 170℃
Shutdown Flag
Tshut
"H" : 16 outputs off,
“L” : normal operation
Normal
Normal
T130=1
170 C
130 C
T130=1
Tshut=1
T170=0,Tshut=1
T170=1
Normal
Normal
In CD mode, thermal flags will be serial-out through DAO. According to these thermal
flags, the control system can adopt proper way to protect whole display system. Please note
the thermal flags are all ‘L’ in normal operation.
SD mode
CD mode transfer
DAI
CD mode
SD mode
1
DA[2]
DA [1]
DA [0]
GBCA [6] GBCA [5]
SVA [1]
SVA [0]
SLPA
DB[15]
DB[14]
1
2
DB [1]
DB [0]
0
15
16
high
LAT
low
15
16
1
2
3
4
1
2
8
9
10
high
DCK
l ow
1
DAO
OUT0
(current )
*1
D Z[0]
DA [15]
GBC Z [6]
GBCZ [5]
SHUT Z
T130 Z
T170 Z
DA [ 15 ]
D A [14 ]
D A [13 ]
D A [0]
D B [15]
0
on
Fr ame Data Z
Fr ame Data Aa
Frame Data A*1
off
The difference between Frame data A and Aa is the max output current.
16-Channel Constant Current LED Driver with Error Detection
Version:A.004
未經授權而逕予重製、複製、使用或公開本文件，行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Page 18
DM13H
Power Dissipation
Notice that the power dissipation of a semiconductor chip is limited to its package and
ambient temperature, in which the device requires the maximum output current calculated
for given operating conditions. The maximum allowable power consumption can be
calculated by the following equation:
Pd(max)(Watt) =
Tj(junction temperature)(max)(°C)– Ta(ambient temperature)(°C)
Rth(junction-to-air thermal resistance)(°C/Watt)
The relationship between power dissipation and operating temperature can be refer to the
figure below:
PD - Ta curve
Power Dissipation Pd(W)
3
2.5
TSSOP24E
2
SSOP24
1.5
1
0.5
0
0
20
40
60
80
100
120
140
160
Ambient Temperature Ta ( ℃ )
The power consumption of IC can be determined by the following equation and should
be less than the maximum allowable power dissipation:
16-Channel Constant Current LED Driver with Error Detection
Version:A.004
未經授權而逕予重製、複製、使用或公開本文件，行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Page 19
DM13H
Package Outline Dimension
SOP24
Dimensions in mm
Symbol
MIN.
TYP.
MAX.
A
-
-
2.650
A1
0.100
-
0.300
A2
2.050
-
-
b
0.310
-
0.510
c
0.200
-
0.330
D
15.240
-
15.700
E1
7.500
BSC
e
1.270
BSC
E
10.300
BSC
L1
1.40
REF
L
0.400
-
1.270
θ°
0
-
8
16-Channel Constant Current LED Driver with Error Detection
Version:A.004
未經授權而逕予重製、複製、使用或公開本文件，行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Page 20
DM13H
Package Outline Dimension
SSOP24
Dimensions in inch
Dimensions in mm
Symbol
MIN.
TYP.
MAX.
MIN.
TYP.
MAX.
A
0.053
0.064
0.069
1.346
1.626
1.753
A1
0.004
0.006
0.01
0.102
0.152
0.254
A2
-
-
0.059
-
-
1.499
b
0.008
-
0.012
0.203
-
0.305
C
0.007
-
0.01
0.178
-
0.254
D
0.337
0.341
0.344
8.56
8.661
8.738
E
0.228
0.236
0.244
5.791
5.994
6.198
e
0.025
BSC
0.635
BSC
E1
0.15
0.154
0.157
3.81
3.912
3.988
L
0.016
0.025
0.05
0.406
0.635
1.27
L1
θ°
0.041 BSC
0
-
1.041 BSC
8
0
16-Channel Constant Current LED Driver with Error Detection
-
8
Version:A.004
未經授權而逕予重製、複製、使用或公開本文件，行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Page 21
DM13H
Package Outline Dimension
TSSOP24E
Dimensions in inch
Dimensions in mm
Symbol
MIN.
TYP.
MAX.
MIN.
TYP.
MAX.
A
-
-
0.047
-
-
1.2
A1
0
-
0.006
0
-
0.15
A2
0.031
0.039
0.041
0.8
1
1.05
b
0.007
-
0.012
0.19
-
0.3
D
0.303
7.8
0.311
7.7
7.8
7.9
E1
0.169
4.4
0.177
4.3
4.4
4.5
E
6.400 BSC
6.400 BSC
e
0.650 BSC
0.650 BSC
L1
1.000 REF
1.000 REF
L
0.018
4.4
0.03
0.45
0.6
S
0.008
-
-
0.2
-
0.75
-
θ°
0
-
8
0
-
8
E2
0.09
-
0.112
2.28
-
2.85
D1
0.146
-
0.182
3.7
-
4.62
PAD SIZE2
(112×18E)
16-Channel Constant Current LED Driver with Error Detection
Version:A.004
未經授權而逕予重製、複製、使用或公開本文件，行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Page 22
DM13H
Package Outline Dimension
SOP24B
16-Channel Constant Current LED Driver with Error Detection
Version:A.004
未經授權而逕予重製、複製、使用或公開本文件，行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Page 23
DM13H
Package Outline Dimension
QFN24
DIMENSION
(MM)
SYMBOL
DIMENSION
(MIL)
MIN. NOM. MAX.
MIN.
NOM.
MAX.
A
0.70
0.75
0.80
27.6
29.5
31.5
A1
0
0.02
0.05
0
0.79
1.97
A3
0.203 REF
8 REF
b
0.18
0.25
0.30
7.09
9.84
11.81
D
3.90
4.00
4.10
153.5
157.5
161.4
D2
1.90
2.00
2.10
74.8
78.7
82.7
E
3.90
4.00
4.10
153.5
157.5
161.4
E2
1.90
2.00
2.10
74.8
78.8
82.7
e
L
y
0.50 BSC
0.30
0.40
0.50
19.69 BSC
11.8
0.08
16-Channel Constant Current LED Driver with Error Detection
15.7
19.7
3.15
Version:A.004
未經授權而逕予重製、複製、使用或公開本文件，行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Page 24
DM13H
The products listed herein are designed for ordinary electronic applications, such
as electrical appliances, audio-visual equipment, communications devices and so
on. Hence, it is advisable that the devices should not be used in medical
instruments, surgical implants, aerospace machinery, nuclear power control
systems, disaster/crime-prevention equipment and the like. Misusing those
products may directly or indirectly endanger human life, or cause injury and
property loss.
Silicon Touch Technology, Inc. will not take any responsibilities regarding the
misusage of the products mentioned above. Anyone who purchases any products
described herein with the above-mentioned intention or with such misused
applications should accept full responsibility and indemnify. Silicon Touch
Technology, Inc. and its distributors and all their officers and employees shall
defend jointly and severally against any and all claims and litigation and all
damages, cost and expenses associated with such intention and manipulation.
Silicon Touch Technology, Inc. reserve the right to make changes to their products
or to discontinue any product or service without notice, and advise customers to
obtain the latest version of relevant information to verify, before placing orders,
that information being relied on is current and complete.
16-Channel Constant Current LED Driver with Error Detection
Version:A.004
未經授權而逕予重製、複製、使用或公開本文件，行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Page 25