622 Mbps Bi-directional Single Fiber Transceiver B-1X/1X-622-TDFB(3)-SSCX Features • Coaxial Single Mode Single Fiber Package with SC Receptacle Connector • Tx 1310 nm/Rx 1550 nm [B-13/15-622-TDFB(3)-SSCX] • Tx 1550 nm/Rx 1310 nm [B-15/13-622-TDFB(3)-SSCX] • SONET OC-12 SDH STM-4 Compliant • Single +5V/+3.3V Power Supply • PECL Differential Inputs and Outputs • Wave Solderable and Aqueous Washable • Class 1 Laser Int. Safety Standard IEC 825 Compliant • Uncooled Laser Diode with MQW Structure • Complies with Telcordia (Bellcore) GR-468-CORE • Temperature Range: 0 to 70 ºC • Optical Isolation > 30 dB • Cross Talk < -33 dB • Optical Return Loss >14 dB Absolute Maximum Rating Parameter Symbol Min. Max. Unit Note Power Supply Voltage Vcc 0 3.6 V B-1X/1X-622-TDFB3-SSCX Power Supply Voltage Vcc 0 6 V B-1X/1X-622-TDFB-SSCX Output Current Iout 0 30 mA Soldering Temperature - - 260 ºC Operating Temperature Topr 0 70 ºC Storage Temperature Tstg -40 85 ºC 10 seconds on leads only Recommended Operating Condition Parameter Symbol Min. Typ. Max. Unit Power Supply Voltage Vcc 3.1 3.3 3.5 V Power Supply Voltage Vcc 4.75 5 5.25 V Operating Temperature Topr 0 - 70 ºC - 622 - Mbps Data Rate LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 1 LUMNDS795-NOV0104 rev. A.0 622 Mbps Bi-directional Single Fiber Transceiver B-1X/1X-622-TDFB(3)-SSCX Transmitter Specifications Parameter Symbol Min Typical Max Unit Notes Optical Transmit Power Po -15 Optical Transmit Power Output Center Wavelength Po -3 - -8 dBm B-1X/1X-622-TDFB(3)-SSC - +2 dBm λ B-1X/1X-622-TDFB(3)-SSC4 1260 1310 1360 nm B-13/15-622-TDFB(3)-SSCX λ 1480 1550 1580 nm B-15/13-622-TDFB(3)-SSCX ∆λ - - 1 nm -20dB width Optical Output Center Wavelength Output Spectrum Width Side Mode Supression Ratio SMSR 30 - - dB Extinction Ratio ER 8.2 - - dB B-1X/1X-622-TDFB(3)-SSC Extinction Ratio ER 10 - - dB B-1X/1X-622-TDFB(3)-SSC4 Output Eye Compliant with Bellcore GR-253-CORE and ITU recommendation G957 Optical Rise Time tr - - 1.2 ns 10% to 90% Values Optical Fall Time tf - - 1.2 ns 10% to 90% Values Optical Return Loss 14 - - dB RIN - - -120 dB/Hz TJ - - 0.55 ns Measured with 223-1 PRBS with 72 ones and 72 zeros. Symbol Min Typical Max Unit Notes Power Supply Current ICC - - 140 mA Data Input Current-Low IIL -350 - - µA Data Input Current-High IIH - - 350 µA Differential Input Voltage VIH-VIL 300 - - mV Data Input Voltage-Low VIL-VCC -2.0 - -1.58 V Data Input Voltage-High VIH-VCC -1.1 - -0.74 V Relative Intensity Noise Total Jitter Transmitter Specifications Parameter Electrical LUMINENTOIC.COM Maximum current is specified at Vcc= Maximum @ maximum temperature These inputs are compatible with 10K, 10KH and 100K ECL and PECL inputs 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 2 LUMNDS795-NOV0104 rev. A.0 622 Mbps Bi-directional Single Fiber Transceiver B-1X/1X-622-TDFB(3)-SSCX Receiver Specifications Parameter Symbol Min Typical Max Unit Notes - - - -28 dBm Maximum Input Power Pin -3 - - dBm Signal Detect-Asserted Pa - - -28 dBm Measured on transition: low to high Signal Detect-Deasserted Pd -40 - - dBm Measured on transition: high to low - 3.0 - dB - - -33 dB Wavelength of Operation 1260 - 1360 nm B-15/13-622-TDFB(3)-SSCX Wavelength of Operation 1480 - 1600 nm B-13/15-622-TDFB(3)-SSCX Min Typical Max Unit Notes The current excludes the output load current Optical Sensitivity Signal Detect-Hysteresis Cross Talk - Measured with 223-1 PRBS with 72 ones and 72 zeros. (ITU-T recommendation G.958) Receiver Specifications Parameter Symbol Electrical ICC - - 100 mA Data Output Voltage-Low VOL -Vcc -1.9 - -1.6 V Data Output Voltage-High VOH- Vcc -1.1 - -0.8 V Signal Detect Output Voltage-Low VSDL-Vcc -1.9 - -1.6 V Signal Detect Output Voltage-High VSDH- Vcc -1.1 - -0.8 V Power Supply Current LUMINENTOIC.COM These outputs are compatible with 10K, 10KH and 100KECL and PECL outputs. 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 3 LUMNDS795-NOV0104 rev. A.0 622 Mbps Bi-directional Single Fiber Transceiver B-1X/1X-622-TDFB(3)-SSCX Connection Diagram 1. (Rx GND) 2. (Rx +) 3. (Rx-) 4. (SD) 5. (Rx Vcc) 6. (Tx Vcc) 7. (TD-) 8. (TD+) 9. (Tx GND) NC Top View NC Receiver Signal Ground Receiver Data Out Receiver Data Out Bar Signal Detect Receiver Power Supply Transmitter Power Supply Transmitter Data In Bar Transmitter Data in Transmitter Signal Ground PIN Symbol Notes 1 RxGND Directly connect this pin to the receiver ground plane 2 RD+ See recommended circuit schematic 3 RD- See recommended circuit schematic 4 SD Active high on this indicates a received optical signal 5 RxVcc +3.3V/+5V dc power for the receiver section 6 TxVcc +3.3V/+5V dc power for the transmitter section 7 TD- See recommended circuit schematic TD+ See recommended circuit schematic 8 Warnings 9 TxGND Directly connect this pin to the transmitter ground plane Legal Notice LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 4 LUMNDS795-NOV0104 rev. A.0 622 Mbps Bi-directional Single Fiber Transceiver B-1X/1X-622-TDFB(3)-SSCX Recommended Circuit Schematic Tx Vcc C5 Rx Vcc 9 R1 7 8 6 5 4 3 2 1 R3 R9 R5 C6 R7 TD + RD + TD - RD - Tx Vcc SD Rx Vcc R2 R4 No internal connection Notes +3.3V: R1=R3=R5=R7=R9=130! R2=R4=R6=R8=R10=82! C1=C2=C3=C5=C6=0.1"F C4=10"F L1=L2=1"H No internal connection Transceiver Top view R10 R6 R8 L1 Notes +5V: R1=R3=R5=R7=R9=82! R2=R4=R6=R8=R10=130! C1=C2=C3=C5=C6=0.1"F C4=10"F L1=L2=1"H Vcc C3 Rx Vcc C1 L2 C4 Tx Vcc C2 The split-loaded terminations for ECL signals need to be located at the input of devices receiving those ECL signals. The power supply filtering is required for good EMI performance. Use short tracks from the inductor L1/L2 to the module Rx Vcc. A GND plane under the module is required for good EMI and sensitivity performance. LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 5 LUMNDS795-NOV0104 rev. A.0 622 Mbps Bi-directional Single Fiber Transceiver B-1X/1X-622-TDFB(3)-SSCX Package Diagram Diplexer Transceiver Assembly (Receptacle Type) Top View Front View Units: mm Rear View Side View LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 6 LUMNDS795-NOV0104 rev. A.0 622 Mbps Bi-directional Single Fiber Transceiver B-1X/1X-622-TDFB(3)-SSCX Ordering Information Available Options: B-15/13-622-TDFB-SSC B-15/13-622-TDFB3-SSC B-15/13-622-TDFB-SSC4 B-15/13-622-TDFB3-SSC4 B-13/15-622-TDFB-SSC4 B-13/15-622-TDFB3-SSC4 B - 1X/1X - 622 - TDFB(3) - S SC Tx power • Wavelength 13/15 = Tx 1310 nm/Rx 1550 nm 15/13 = Tx 1550 nm/Rx 1310 nm • Communication protocol (622 Mbps) • TDFB= +5V Transceiver TDFB3= +3.3V Transceiver • Single mode fiber • Connector options • Tx power range blank = -15 to -8 dBm 4 = -3 to +2 dBm Warnings: Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static free environment is highly recommended. Follow guidelines according to proper ESD procedures. Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or indirect radiation. Legal Notes: IMPORTANT NOTICE! All information contained in this document is subject to change without notice, at LuminentOIC’s sole and absolute discretion. LuminentOIC warrants performance of its products to current specifications only in accordance with the company’s standard one-year warranty; however, specifications designated as “preliminary” are given to describe components only, and LuminentOIC expressly disclaims any and all warranties for said products, including express, implied, and statutory warranties, warranties of merchantability, fitness for a particular purpose, and non-infringement of proprietary rights. Please refer to the company’s Terms and Conditions of Sale for further warranty information. LuminentOIC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual property described herein. No license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and LuminentOIC makes no representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual property rights. Products described in this document are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. LuminentOIC customers using or selling products for use in such applications do so at their own risk and agree to fully defend and indemnify LuminentOIC for any damages resulting from such use or sale. THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN “AS IS” BASIS. Customer agrees that LuminentOIC is not liable for any actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. Customer must contact LuminentOIC to obtain the latest version of this publication to verify, before placing any order, that the information contained herein is current. © LuminentOIC, Inc. 2003 All rights reserved LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 7 LUMNDS795-NOV0104 rev. A.0