AP7215 600mA CMOS LDO General Description Features • • • • • • • • • Very Low Dropout Voltage Low Current Consumption: Typ. 50μA Output Voltage: 3.3V Guaranteed 600mA Output Input Range up to 5.5V Current Limit Protection Stable with either electrolytic capacitor or low-ESR MLCC (multi-layer ceramic capacitor) Low Temperature Coefficient SOP-8L and SOT89-3L: Available in “Green” Molding Compound (No Br, Sb) Lead Free Finish / RoHS Compliant (Note 1) The AP7215 low-dropout linear regulator operates from a 3.3V to 5.5V supply and delivers a guaranteed 600mA continuous load current. The high-accuracy output voltage is preset to an internally trimmed voltage. An active-low open-drain reset output remains asserted for at least 20ms (TYP) after input voltage rises above the reset threshold. The space-saving SOP-8L and SOT89-3L package are suitable for “pocket” and hand-held applications. Applications • • • • HD/Blue-Ray DVD & MP3/4 Players Mobile Handsets and Smart Phones Digital Still Camera Hand-Held Computers Ordering Information AP7215 - 33 X G - 13 Output voltage Package Green Packing 33 : 3.3V S : SOP-8L Y : SOT89-3L G : Green 13 : Tape & Reel Device AP7215-33SG-13 AP7215-33YG-13 Notes: Package Code S Y Packaging (Note 2) SOP-8L SOT89-3L 13” Tape and Reel Quantity Part Number Suffix 2500/Tape & Reel -13 2500/Tape & Reel -13 1. EU Directive 2002/95/EC (RoHS). All applicable RoHS exemptions applied, see EU Directive 2002/95/EC Annex Notes. 2. Pad layout as shown on Diodes Inc. suggested pad layout document AP02001, which can be on our website at http://www.diodes.com/datasheets/ap02001.pdf. AP7215 Rev. 1 1 of 11 www.diodes.com FEBRUARY 2009 © Diodes Incorporated AP7215 600mA CMOS LDO Pin Assignments (1) SOP-8L (2) SOT89-3L ( Top View ) ( Top View ) NC 1 8 EN 3 VROUT VR OUT 2 7 GND 2 VIN NC 3 6 VDOUT 1 GND V IN 4 5 NC Tab is VIN Pin Descriptions Pin Name NC VROUT VIN VDOUT GND EN AP7215 Rev. 1 SOP-8L 1, 3 , 5 2 4 6 7 8 Pin No. SOT89-3L 3 2 1 - Description No Connection Voltage Output Supply Voltage VD Output Voltage (Reset Output) Ground Enable (VROUT ON/OFF) 2 of 11 www.diodes.com FEBRUARY 2009 © Diodes Incorporated AP7215 600mA CMOS LDO Block Diagram EN Enable VIN On - Off ERROR AMP Bandgap Current Limit + VROUT 1.2V R1 VDOUT + R3 R2 VD Comp. R4 GND Absolute Maximum Ratings Symbol Parameter ESD HBM Human Body Model ESD Protection ESD MM VIN VROUT TJ(MAX) Machine Model ESD Protection Input Voltage Output Voltage Maximum Junction Temperature SOP-8L Power Dissipation SOT89-3L PD Rating Unit 2 KV 350 +6 GND - 0.3 ~ VIN+ 0.3 150 1.2 0.79 V V V ºC W W Recommended Operating Conditions Symbol VIN IOUT TJ TA AP7215 Rev. 1 Parameter Input Voltage Output Current Operating Junction Temperature Range Operating Ambient Temperature 3 of 11 www.diodes.com Min 3.3 0 -40 -40 Max 5.5 600 125 85 Unit V mA ºC ºC FEBRUARY 2009 © Diodes Incorporated AP7215 600mA CMOS LDO Electrical Characteristics (TA = 25°C, CIN = 1µF, COUT = 1µF, VIN=5.0V, VEN = VIN, unless otherwise noted) Symbol Parameter Test Conditions Min ICCQ Quiescent Current IOUT = 0mA VEN = GND ISTBY Standby Current VIN = 5.0V Output Voltage VROUT 3.234 IOUT = 30mA, VIN = 5V Accuracy VROUT Temperature ΔVROUT/ΔTA/VROUT TA =-40°C to 85°C, IOUT = 30mA Coefficient VDO IOUT ILIMIT ISHORT ΔVROUT/ΔVIN/VROU Dropout Voltage Typ. 50 Max 80 Unit μA 15 30 μA 3.300 3.366 V ppm / oC ±100 IOUT = 30mA 60 100 mV IOUT = 100mA 100 250 mV Maximum Output VIN = 5.3V Current Current Limit VIN = 5.3V Short Circuit Current VIN = 5.3V 600 mA 750 50 mA mA Line Regulation 4.3V ≤ VIN ≤ 5.5V, IOUT = 30mA 0.01 ±0.2 %/V Load Regulation 1mA ≤ IOUT ≤ 100mA, VIN = 5.3V 15 50 mV Power Supply Rejection VIN = 4.3V+ 0.5Vp-pAC, F= 1KHz IOUT = 50mA 55 EN Input Threshold Output ON Output OFF T ΔVROUT PSRR VEH VEL IEN VDF VHYS IVDOUT tRP θJA θJC Notes: Enable Pin Current VIN Detection Voltage Detect VDOUT fall VDF Hysteresis Range VDOUT Sink Current 1.6 -0.1 3.83 VDF x1.02 VDOUT = 0.5V, VIN = 2.0V VDOUT = 0.5V, VIN = 3.0V VDOUT Delay Time Thermal Resistance SOP-8L (Note 3) Junction-to-Ambient SOT89-3L (Note 3) Thermal Resistance SOP-8L (Note 3) Junction-to-Case SOT89-3L (Note 3) dB 10 3.91 VDF x1.05 20 30 20 124 173 25 42 0.25 0.1 3.98 VDF x1.08 V V μA V V mA 40 ms ºC/W ºC/W 3. Test conditions for SOP-8L, SOT89-3L: Device mounted on FR-4 substrate, single sided PC board, 2oz copper, with minimum recommended pad layout. AP7215 Rev. 1 4 of 11 www.diodes.com FEBRUARY 2009 © Diodes Incorporated AP7215 600mA CMOS LDO Typical Application 4 VIN U1 VIN 2 VR OUT AP7215 100K CIN VR OUT ON VD OUT 1uF 6 VD OUT GND EN 8 OFF C OUT 1uF 7 Timing Diagram tRP 20mSec-TYP. VHYS VDF VIN VDOUT EN VROUT AP7215 Rev. 1 5 of 11 www.diodes.com FEBRUARY 2009 © Diodes Incorporated AP7215 600mA CMOS LDO Typical Performance Characteristics Standby Current vs Input Voltage ISTBY (uA) ICCQ (uA) Quiescent Current vs Input Voltage 90 80 70 60 50 40 30 20 10 0 3.0 3.5 4.0 4.5 VIN (V) 5.0 5.5 80 70 60 50 40 30 20 10 0 3.0 6.0 4.0 5.0 5.5 6.0 Dropout Voltage vs Output Current 600 500 400 300 200 100 0 -40 -20 0 20 40 60 80 100 120 0 100 200 Ambient Temperature (C) ISHORT(mA) 960 940 920 900 880 860 840 820 800 780 760 -40 -20 0 20 40 60 80 100 120 500 600 700 90 85 80 75 70 65 60 55 50 3.0 Ambient Temperature AP7215 Rev. 1 300 400 IOUT (mA) Short Circuit Current vs Input Voltage Current Limit vs Ambient Temperature Current Limit (mA) 4.5 VIN (V) 700 28 27 26 25 24 23 22 21 20 VDO (mV) Delay Time (ms) Delay Time vs Ambient Temperature 3.5 6 of 11 www.diodes.com 3.5 4.0 4.5 VIN (V) 5.0 5.5 6.0 FEBRUARY 2009 © Diodes Incorporated AP7215 600mA CMOS LDO Typical Performance Characteristics (Continued) Load Transient Response (VIN=4.3V, IOUT=10mA ~600mA) Load Transient Response (VIN=4.3V, IOUT=10mA ~300mA) VIN VIN VROUT VROUT IOUT IOUT Load Transient Response (VIN=5.5V, IOUT=10mA~600mA) Load Transient Response (VIN=5.5V, IOUT=10mA~300mA) VIN VIN VROUT VROUT IOUT IOUT AP7215 Rev. 1 7 of 11 www.diodes.com FEBRUARY 2009 © Diodes Incorporated AP7215 600mA CMOS LDO Application Note Input Capacitor A 1μF ceramic capacitor is recommended to connect between VIN and GND pins to decouple input power supply glitch and noise. The amount of the capacitance may be increased without limit. A lower ESR (Equivalent Series Resistance) capacitor allows the use of less capacitance, while higher ESR type requires more capacitance. This input capacitor must be located as close as possible to the device to assure input stability and less noise. For PCB layout, a wide copper trace is required for both VIN and GND. Suggested Input Capacitance Vendor Capacitance TAIYO YUDEN 1μF EN=0 EN=1 Type Series Ceramic LMK212B Output Capacitor The output capacitor is required to stabilize and help the transient response of the LDO. The AP7215 is designed to have excellent transient response for most applications with a small amount of output capacitance. The AP7215 is stable with any small ceramic output capacitors of 1.0μF or higher value, and the temperature coefficients of X7R or X5R type. Additional capacitance helps to reduce undershoot and overshoot during transient. For PCB layout, the output capacitor must be placed as close as possible to VROUT and GND pins, and keep the leads as short as possible. Suggested Output Capacitance Vendor Capacitance Type Series TAIYO YUDEN 1μF Ceramic LMK212B Suggested Resistance Vendor Capacitance YAGEO SMD Type FR-SK ENABLE/SHUTDOWN Operation The AP7215 is turned on by setting the EN pin high, and is turned off by pulling it low. If this feature is not used, the EN pin should be tied to VIN pin to keep the regulator output on at all time. To ensure proper operation, the signal source used to drive the EN pin must be able to swing above and below the specified turn-on/off voltage thresholds listed in the Electrical Characteristics section under VEH and VEL. VROUT 0V 3.3V VDOUT Φ Φ Current Limit Protection When output current at VROUT pin is higher than current limit threshold, the current limit protection will be triggered and clamp the output current to approximately 750mA to prevent over-current and protect the regulator from damage due to overheating. Short circuit protection When VROUT pin is shorted to GND or VROUT voltage is less than 200mV, short circuit protection will be triggered and clamp the output current to approximately 50mA. VDOUT (reset output) ---Open-Drain Active-Low reset output--In general, VDOUT is pulled up by a resistor (100KΩ) to VIN. The AP7215 microprocessor (μP) supervisory circuitry asserts a guaranteed logic-low reset during power-up and power-down. Reset is asserted when VIN is below the reset threshold and remain asserted for at least tRP after VIN rises above the reset threshold. As long as VIN is lower than the reset threshold, VDOUT remains at logic "0". When VIN becomes higher than VHYS, a logic "1" is asserted after a 20ms time delay defined by tRP AP7215 Rev. 1 8 of 11 www.diodes.com FEBRUARY 2009 © Diodes Incorporated AP7215 600mA CMOS LDO Marking Information (1) SOP-8L ( Top View ) 5 8 YY : Year : 08, 09,10~ WW : Week : 01~52; 52 represents 52 and 53 week X : Internal Code G : Green Logo AP7215-33 YY WW X X Part Number 1 4 (2) SOT89-3L ( Top View ) XX Y W X 1 AP7215 Rev. 1 2 3 XX : Identification code Y : Year : 0~9 W : Week : A~Z : 1~26 week; a~z : 27~52 week; z represents 52 and 53 week X : Internal code A~Z : Green Device Package type Identification Code AP7215Y SOT89-3L N8 9 of 11 www.diodes.com FEBRUARY 2009 © Diodes Incorporated AP7215 600mA CMOS LDO Package Information (All Dimensions in mm) 0.254 0.10/0.20 3.85/3.95 5.90/6.10 (1) Package Type: SOP-8L Gauge Plane Seating Plane 0.62/0.82 Detail "A" 7°~9° 7°~9° 0.15/0.25 1.30/1.50 1.75max. 0.35max. 45° Detail "A" 0°/8° 0.3/0.5 1.27typ 4.85/4.95 5.4 8x-0.60 8x-1.55 6x-1.27 Land Pattern Recommendation (Unit: mm) (2) Package Type: SOT89-3L 1.40/1.75 Typ 1.60 2.7 3.94/4.25 1.45/1.55 Typ 1.50 1.3 1.9 0.4 0.80/ 1.20 2.35/2.60 Typ 2.48 1.7 1.5 0.9 Land Pattern Recommendation (Unit: mm) 2.90/3.10 Typ 3.00 50 (2x) 80 (2x) 1.40/1.60 Typ 1.50 4.40/4.60 Typ 4.50 0.36/0.48 0.41/0.53 0.36/0.48 Typ 0.42 Typ 0.47 Typ 0.42 AP7215 Rev. 1 0.35/0.43 Typ 0.39 10 of 11 www.diodes.com FEBRUARY 2009 © Diodes Incorporated AP7215 600mA CMOS LDO IMPORTANT NOTICE Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes without further notice to any product herein. Diodes Incorporated does not assume any liability arising out of the application or use of any product described herein; neither does it convey any license under its patent rights, nor the rights of others. The user of products in such applications shall assume all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on our website, harmless against all damages. LIFE SUPPORT Diodes Incorporated products are not authorized for use as critical components in life support devices or systems without the expressed written approval of the President of Diodes Incorporated. AP7215 Rev. 1 11 of 11 www.diodes.com FEBRUARY 2009 © Diodes Incorporated