ATMEL AT17LV256A Fpga configuration eeprom memory Datasheet

Features
• EE Programmable 65,536 x 1-, 131,072 x 1-, 262,144 x 1-, 524,288 x 1-, 1,048,576 x 1- and
•
•
•
•
•
•
•
•
•
•
•
•
2,097,152 x 1-bit Serial Memories Designed to Store Configuration Programs for
Altera® FLEX® and APEX™ FPGAs (Device Selection Guide Included)
Available as a 3.3V (±10%) and 5.0V (±5% Commercial, ±10% Industrial) Version
In-System Programmable (ISP) via 2-wire Bus
Simple Interface to SRAM FPGAs
Compatible with Atmel AT6000, AT40K and AT94K Devices, Altera FLEX, APEX
Devices, ORCA® FPGAs, Xilinx® XC3000, XC4000, XC5200, Spartan®, Virtex™ FPGAs,
Motorola MPA1000 FPGAs
Cascadable Read-back to Support Additional Configurations or Higher-density Arrays
Very Low-power CMOS EEPROM Process
Programmable Reset Polarity
Available 8-lead PDIP, 20-lead PLCC and 32-lead TQFP Packages (Pin Compatible
Across Product Family)
Emulation of Atmel’s AT24CXXX Serial EEPROMs
Low-power Standby Mode
High-reliability
– Endurance: 100,000 Write Cycles
– Data Retention: 90 Years for Industrial Parts (at 85°C) and 190 Years for
Commercial Parts (at 70°C)
Green (Pb/Halide-free/RoHS Compliant) Package Options Available
1. Description
The AT17A series FPGA configuration EEPROMs (Configurators) provide an easy-touse, cost-effective configuration memory for Field Programmable Gate Arrays. The
AT17A series device is packaged in the 8-lead PDIP(1), 20-lead PLCC and 32-lead
TQFP, see Table 1-1. The AT17A series configurator uses a simple serial-access procedure to configure one or more FPGA devices. The user can select the polarity of the
reset function by programming four EEPROM bytes.These devices also support a
write-protection mechanism within its programming mode.
Note:
1. The 8-lead LAP, PDIP and SOIC packages for the AT17LV65A/128A/256A do not
have an A label. However, the 8-lead packages are pin compatible with the 8-lead
package of Altera’s EEPROMs, refer to the AT17LV65/128/256/512/010/002/040
datasheet available on the Atmel web site for more information.
FPGA
Configuration
EEPROM
Memory
AT17LV65A
AT17LV128A
AT17LV256A
AT17LV512A
AT17LV010A
AT17LV002A
3.3V and 5V
System Support
The AT17A series configurators can be programmed with industry-standard programmers, Atmel’s ATDH2200E Programming Kit or Atmel’s ATDH2225 ISP Cable.
Table 1-1.
AT17A Series Packages
AT17LV65A/
AT17LV128A/
AT17LV256A
AT17LV512A
AT17LV010A
AT17LV002A
8-lead
PDIP
Yes
Yes
Yes
–
20-lead
PLCC
Yes
Yes
Yes
Yes
32-lead
TQFP
–
–
Yes
Yes
Package
2322G–CNFG–03/06
2. Pin Configuration
Figure 2-1.
8-lead PDIP
DATA
DCLK
(1)
(WP ) RESET/OE
nCS
20-lead PLCC
18
17
16
15
14
9
10
11
12
13
4
5
6
7
8
SER_EN
NC
NC
NC (READY(2))
NC
nCS
GND
NC
(A2) nCASC(4)
NC
DCLK
(2)
WP1
NC
NC
(1)
(WP ) RESET/OE
3
2
1
20
19
NC
DATA
NC
VCC
NC
Figure 2-2.
VCC
SER_EN
(A2) nCASC(4)
GND
8
7
6
5
1
2
3
4
32-lead TQFP
32
31
30
29
28
27
26
25
NC
DATA
NC
NC
NC
VCC
NC
NC
Figure 2-3.
24
23
22
21
20
19
18
17
1
2
3
4
5
6
7
8
NC
SER_EN
NC
NC
READY
NC
NC
NC
NC
nCS
NC
GND
NC
NC
(A2) nCASC
NC
9
10
11
12
13
14
15
16
NC
DCLK
NC
(3)
(WP1 ) NC
NC
NC
RESET/OE
NC
Notes:
1. This pin is only available on AT17LV65A/128A/256A devices.
2. This pin is only available on AT17LV512A/010A/002A devices.
3. This pin is only available on AT17LV010A/002A devices.
4. The nCASC feature is not available on the AT17LV65A device.
2
AT17LV65A/128A/256A/512A/002A
2322G–CNFG–03/06
AT17LV65A/128A/256A/512A/002A
Figure 2-4.
Block Diagram
SER_EN
WP1(2)
OSCILLATOR
CONTROLL
OSCILLATOR
(3)
POWER ON
RESET
(2)
DCLK READY
Notes:
RESET/OE
(1)
(WP )
nCS
nCASC
1. This pin is only available on AT17LV65A/128A/256A devices.
2. This pin is only available on AT17LV512A/010A/002A devices.
3. The nCASC feature is not available on the AT17LV65A device.
3
2322G–CNFG–03/06
3. Device Description
The control signals for the configuration EEPROM (nCS, RESET/OE and DCLK) interface
directly with the FPGA device control signals. All FPGA devices can control the entire configuration process and retrieve data from the configuration EEPROM without requiring an external
controller.
The configuration EEPROM’s RESET/OE and nCS pins control the tri-state buffer on the DATA
output pin and enable the address counter and the oscillator. When RESET/OE is driven Low,
the configuration EEPROM resets its address counter and tri-states its DATA pin. The nCS pin
also controls the output of the AT17A series configurator. If nCS is held High after the
RESET/OE pulse, the counter is disabled and the DATA output pin is tri-stated. When nCS is
driven subsequently Low, the counter and the DATA output pin are enabled. When RESET/OE
is driven Low again, the address counter is reset and the DATA output pin is tri-stated, regardless of the state of the nCS.
When the configurator has driven out all of its data and nCASC is driven Low, the device tristates the DATA pin to avoid contention with other configurators. Upon power-up, the address
counter is automatically reset.
This is the default setting for the device. Since almost all FPGAs use RESET Low and OE High,
this document will describe RESET/OE.
4. Pin Description
AT17LV65A/
AT17LV128A/
AT17LV256A
AT17LV512A/
AT17LV010A
AT17LV002A
Name
I/O
20
PLCC
8
PDIP
20
PLCC
32
TQFP
20
PLCC
32
TQFP
DATA
I/O
2
1
2
31
2
31
DCLK
I
4
2
4
2
4
2
WP1
I
–
–
5
4
5
4
RESET/OE
I
8
3
8
7
8
7
nCS
I
9
4
9
10
9
10
10
5
10
12
10
12
12
6
12
15
12
15
GND
nCASC
O
A2
I
READY
O
–
–
15
20
15
20
SER_EN
I
18
7
18
23
18
23
20
8
20
27
20
27
VCC
Note:
4
1. The nCASC feature is not available on the AT17LV65A device.
AT17LV65A/128A/256A/512A/002A
2322G–CNFG–03/06
AT17LV65A/128A/256A/512A/002A
4.1
DATA
Three-state DATA output for configuration. Open-collector bi-directional pin for programming.
4.2
DCLK
Clock output or clock input. Rising edges on DCLK increment the internal address counter and
present the next bit of data to the DATA pin. The counter is incremented only if the RESET/OE
input is held High, the nCS input is held Low, and all configuration data has not been transferred
to the target device (otherwise, as the master device, the DCLK pin drives Low).
4.3
WP1
WRITE PROTECT (1). This pin is used to protect portions of memory during programming, and
it is disabled by default due to internal pull-down resistor. This input pin is not used during FPGA
loading operations. This pin is only available on AT17LV512A/010A/002A devices.
4.4
RESET/OE
Output Enable (active High) and RESET (active Low) when SER_EN is High. A Low logic level
resets the address counter. A High logic level (with nCS Low) enables DATA and permits the
address counter to count. In the mode, if this pin is Low (reset), the internal oscillator becomes
inactive and DCLK drives Low. The logic polarity of this input is programmable and must be programmed active High (RESET active Low) by the user during programming for Altera
applications.
4.5
WP
Write protect (WP) input (when nCS is Low) during programming only (SER_EN Low). When
WP is Low, the entire memory can be written. When WP is enabled (High), the lowest block of
the memory cannot be written. This pin is only available on AT17LV65A/128A/256A devices.
4.6
nCS
Chip Select input (active Low). A Low input (with OE High) allows DCLK to increment the
address counter and enables DATA to drive out. If the AT17A series is reset with nCS Low, the
device initializes as the first (and master) device in a daisy-chain. If the AT17A series is reset
with nCS High, the device initializes as a subsequent AT17A series device in the chain.
4.7
GND
Ground pin. A 0.2 µF decoupling capacitor between VCC and GND is recommended.
4.8
nCASC
Cascade Select Output (active Low). This output goes Low when the address counter has
reached its maximum value. In a daisy-chain of AT17A series devices, the nCASC pin of one
device is usually connected to the nCS input pin of the next device in the chain, which permits
DCLK from the master configurator to clock data from a subsequent AT17A series device in the
chain. This feature is not available on the AT17LV65A device.
4.9
A2
Device selection input, A2. This is used to enable (or select) the device during programming
(i.e., when SER_EN is Low). A2 has an internal pull-down resistor.
5
2322G–CNFG–03/06
4.10
READY
Open collector reset state indicator. Driven Low during power-on reset cycle, released when
power-up is complete. (recommended 4.7 kΩ pull-up on this pin if used).
4.11
SER_EN
Serial enable must be held High during FPGA loading operations. Bringing SER_EN Low
enables the 2-wire Serial Programming Mode. For non-ISP applications, SER_EN should be tied
to VCC.
4.12
VCC
3.3V (±10%) and 5.0V (±5% Commercial, ±10% Industrial) power supply pin.
5. FPGA Master Serial Mode Summary
The I/O and logic functions of any SRAM-based FPGA are established by a configuration program. The program is loaded either automatically upon power-up, or on command, depending
on the state of the FPGA mode pins. In Master mode, the FPGA automatically loads the configuration program from an external memory. The AT17A Serial Configuration EEPROM has been
designed for compatibility with the Master Serial mode.
This document discusses the Altera FLEX FPGA device interfaces
6. Control of Configuration
Most connections between the FPGA device and the AT17A Serial EEPROM are simple and
self-explanatory.
• The DATA output of the AT17A series configurator drives DIN of the FPGA devices.
• The master FPGA DCLK output or external clock source drives the DCLK input of the AT17A
series configurator.
• The nCASC output of any AT17A series configurator drives the nCS input of the next
configurator in a cascaded chain of EEPROMs.
• SER_EN must be connected to VCC (except during ISP).
7. Cascading Serial Configuration EEPROMs
For multiple FPGAs configured as a daisy-chain, or for FPGAs requiring larger configuration
memories, cascaded configurators provide additional memory.
After the last bit from the first configurator is read, the next clock signal to the configurator
asserts its nCASC output low and disables its DATA line driver. The second configurator recognizes the low level on its nCS input and enables its DATA output.
After configuration is complete, the address counters of all cascaded configurators are reset if
the RESET/OE on each configurator is driven to a Low level.
If the address counters are not to be reset upon completion, then the RESET/OE input can be
tied to a High level.
The AT17LV65A devices do not have the nCASC feature to perform cascaded configurations.
6
AT17LV65A/128A/256A/512A/002A
2322G–CNFG–03/06
AT17LV65A/128A/256A/512A/002A
8. AT17A Series Reset Polarity
The AT17A series configurator allows the user to program the polarity of the RESET/OE pin as
either RESET/OE or RESET/OE. This feature is supported by industry-standard programmer
algorithms.
9. Programming Mode
The programming mode is entered by bringing SER_EN Low. In this mode the chip can be programmed by the 2-wire serial bus. The programming is done at VCC supply only. Programming
super voltages are generated inside the chip.
10. Standby Mode
The AT17LV65A/128A/256A enters a low-power standby mode whenever nCS is asserted High.
In this mode, the configurator consumes less than 50 µA of current at 3.3V (100 µA for the
AT17LV512A/010A/002A). The output remains in a high-impedance state regardless of the state
of the RESET/OE input.
11. Absolute Maximum Ratings*
Operating Temperature.................................... -40°C to +85 °C
*NOTICE:
Storage Temperature ..................................... -65°C to +150°C
Voltage on Any Pin
with Respect to Ground ..............................-0.1V to VCC +0.5V
Supply Voltage (VCC) .........................................-0.5V to +7.0V
Stresses beyond those listed under Absolute
Maximum Ratings may cause permanent damage to the device. This is a stress rating only and
functional operation of the device at these or any
other conditions beyond those listed under operating conditions is not implied. Exposure to Absolute Maximum Rating conditions for extended
periods of time may affect device reliability.
Maximum Soldering Temp. (10 sec. @ 1/16 in.).............260°C
ESD (RZAP = 1.5K, CZAP = 100 pF)................................. 2000V
12. Operating Conditions
3.3V
Symbol
Description
5V
Min
Max
Min
Max
Units
Commercial
Supply voltage relative to GND
-0°C to +70°C
3.0
3.6
4.75
5.25
V
Industrial
Supply voltage relative to GND
-40°C to +85°C
3.0
3.6
4.5
5.5
V
VCC
7
2322G–CNFG–03/06
13. DC Characteristics
VCC = 3.3V ± 10%
AT17LV65A/
AT17LV128A/
AT17LV256A
AT17LV512A/
AT17LV010A
AT17LV002A
Symbol
Description
Min
Max
Min
Max
Min
Max
Units
VIH
High-level Input Voltage
2.0
VCC
2.0
VCC
2.0
VCC
V
VIL
Low-level Input Voltage
0
0.8
0
0.8
0
0.8
V
VOH
High-level Output Voltage (IOH = -2.5 mA)
VOL
Low-level Output Voltage (IOL = +3 mA)
VOH
High-level Output Voltage (IOH = -2 mA)
VOL
Low-level Output Voltage (IOL = +3 mA)
ICCA
Supply Current, Active Mode
IL
Input or Output Leakage Current (VIN = VCC or GND)
ICCS
Supply Current, Standby Mode
2.4
2.4
2.4
V
Commercial
0.4
2.4
0.4
2.4
0.4
2.4
V
V
Industrial
-10
0.4
0.4
0.4
V
5
5
5
mA
10
µA
10
-10
10
-10
Commercial
50
100
150
µA
Industrial
100
100
150
µA
AT17LV65A/
AT17LV128A/
AT17LV256A
AT17LV512A/
AT17LV010A
AT17LV002A
14. DC Characteristics
VCC = 5V ± 5% Commercial; VCC = 5V ± 10% Industrial
Symbol
Description
Min
Max
Min
Max
Min
Max
Units
VIH
High-level Input Voltage
2.0
VCC
2.0
VCC
2.0
VCC
V
VIL
Low-level Input Voltage
0
0.8
0
0.8
0
0.8
V
VOH
High-level Output Voltage (IOH = -2.5 mA)
VOL
Low-level Output Voltage (IOL = +3 mA)
VOH
High-level Output Voltage (IOH = -2 mA)
VOL
Low-level Output Voltage (IOL = +3 mA)
ICCA
Supply Current, Active Mode
IL
Input or Output Leakage Current (VIN = VCC or GND)
ICCS1
Supply Current, Standby Mode
8
3.7
3.86
3.86
V
Commercial
0.32
3.6
0.32
3.76
0.32
3.76
V
V
Industrial
-10
0.37
0.37
0.37
V
10
10
10
mA
10
µA
10
-10
10
-10
Commercial
75
200
350
µA
Industrial
150
200
350
µA
AT17LV65A/128A/256A/512A/002A
2322G–CNFG–03/06
AT17LV65A/128A/256A/512A/002A
15. AC Waveforms
nCS
TSCE
TSCE
THCE
RESET/OE
TLC
THOE
THC
DCLK
TOE
TCAC
TOH
TDF
TCE
DATA
TOH
16. AC Waveforms when Cascading
RESET/OE
nCS
DCLK
TCDF
DATA
LAST BIT
TOCK
FIRST BIT
TOCE
TOOE
nCASL
TOCE
9
2322G–CNFG–03/06
17. AC Characteristics
VCC = 3.3V ± 10%
AT17LV65A/128A/256A
Commercial
Symbol
Description
Min
Max
AT17LV512A/010A/002A
Industrial
Min
Max
Units
50
55
ns
60
55
60
ns
80
55
60
ns
OE to Data Delay
50
55
TCE(1)
CE to Data Delay
60
CLK to Data Delay
75
TCAC
(1)
TOH
TDF
(2)
Data Hold from CE, OE, or CLK
0
0
CE or OE to Data Float Delay
Min
Max
0
55
Industrial
Max
(1)
TOE
Commercial
Min
0
55
ns
50
50
ns
TLC
CLK Low Time
25
25
25
25
ns
THC
CLK High Time
25
25
25
25
ns
TSCE
CE Setup Time to CLK
(to guarantee proper counting)
35
60
30
35
ns
THCE
CE Hold Time from CLK
(to guarantee proper counting)
0
0
0
0
ns
THOE
OE High Time (guarantees counter is reset)
25
25
25
25
ns
FMAX
Maximum Input Clock Frequency
10
10
15
10
MHz
Notes:
1. AC test lead = 50 pF.
2. Float delays are measured with 5 pF AC loads. Transition is measured ± 200 mV from steady-state active levels.
18. AC Characteristics when Cascading
VCC = 3.3V ± 10%
AT17LV65A/128A/256A
Commercial
Description
TCDF(2)
CLK to Data Float Delay
60
60
TOCK(1)
CLK to CEO Delay
55
TOCE(1)
CE to CEO Delay
TOOE(1)
RESET/OE to CEO Delay
FMAX
Maximum Input Clock Frequency
8
Max
Industrial
Symbol
Notes:
Min
AT17LV512A/010A/002A
Min
Min
Units
50
50
ns
60
50
55
ns
55
60
35
40
ns
40
45
35
35
ns
12.5
Max
Industrial
Max
8
Max
Commercial
Min
10
MHz
1. AC test lead = 50 pF.
2. Float delays are measured with 5 pF AC loads. Transition is measured ± 200 mV from steady-state active levels.
10
AT17LV65A/128A/256A/512A/002A
2322G–CNFG–03/06
AT17LV65A/128A/256A/512A/002A
19. AC Characteristics
VCC = 5V ± 5% Commercial; VCC = 5V ± 10% Industrial
AT17LV65A/128A/256A
Commercial
Symbol
Description
Min
Max
AT17LV512A/010A/002A
Industrial
Min
Max
Units
30
35
ns
45
45
45
ns
55
50
50
ns
OE to Data Delay
30
35
TCE(1)
CE to Data Delay
45
CLK to Data Delay
50
TCAC
(1)
TOH
TDF
(2)
Data Hold from CE, OE, or CLK
0
0
CE or OE to Data Float Delay
Min
Max
0
50
Industrial
Max
(1)
TOE
Commercial
Min
0
50
ns
50
50
ns
TLC
CLK Low Time
20
20
20
20
ns
THC
CLK High Time
20
20
20
20
ns
TSCE
CE Setup Time to CLK (to guarantee proper
counting)
35
40
20
25
ns
THCE
CE Hold Time from CLK (to guarantee proper
counting)
0
0
0
0
ns
THOE
OE High Time (guarantees counter is reset)
20
20
20
20
ns
FMAX
Maximum Input Clock Frequency
12.5
12.5
15
15
MHz
Notes:
1. AC test lead = 50 pF.
2. Float delays are measured with 5 pF AC loads. Transition is measured ± 200 mV from steady-state active levels.
20. AC Characteristics when Cascading
VCC = 5V ± 5% Commercial; VCC = 5V ± 10% Industrial
AT17LV65A/128A/256A
Commercial
Description
TCDF(2)
CLK to Data Float Delay
50
50
TOCK(1)
CLK to CEO Delay
35
TOCE(1)
CE to CEO Delay
TOOE(1)
RESET/OE to CEO Delay
FMAX
Maximum Input Clock Frequency
10
Max
Industrial
Symbol
Notes:
Min
AT17LV512A/010A/002A
Min
Min
Units
50
50
ns
40
35
40
ns
35
35
35
35
ns
30
35
30
30
ns
12.5
Max
Industrial
Max
10
Max
Commercial
Min
12.5
MHz
1. AC test lead = 50 pF.
2. Float delays are measured with 5 pF AC loads. Transition is measured ± 200 mV from steady-state active levels.
11
2322G–CNFG–03/06
21. Thermal Resistance Coefficients(1)
AT17LV65A/
AT17LV128A/
AT17LV256A
Package Type
8P3
20J
Plastic Dual Inline Package (PDIP)
Plastic Leaded Chip Carrier (PLCC)
32A
Thin Plastic Quad Flat Package
(TQFP)
44J
Plastic Leaded Chip Carrier (PLCC)
Notes:
θJC [°C/W]
θJA [°C/W]
AT17LV512A/
AT17LV010A
AT17LV002A
37
(2)
107
θJC [°C/W]
35
35
35
θJA [°C/W](2)
90
90
90
θJC [°C/W]
–
–
15
θJA [°C/W](2)
–
–
50
θJC [°C/W]
θJA [°C/W](2)
1. For more information refer to the “Thermal Characteristics of Atmel’s Packages”, available on the Atmel web site.
2. Airflow = 0 ft/min.
12
AT17LV65A/128A/256A/512A/002A
2322G–CNFG–03/06
AT17LV65A/128A/256A/512A/002A
22. Ordering Information
Figure 22-1. Ordering Code(1)
AT17LV65A-10PC
Note:
Voltage
Size (Bits)
Special Pinouts
Package
Temperature
3.3V Nominal to
65
= 65K
A
= Altera
P
= 8P3
C = Commercial
5V Nominal
128
= 128K
Blank = Xilinx/Atmel/
Other
J
= 20J
I = Industrial
256
= 256K
512
= 512K
010
= 1M
002
= 2M
Q = 32A
U = Fully Green
1. The 8-lead LAP and SOIC packages for the AT17LV65A/128A/256A do not have an A label. However, the 8-lead packages
are pin compatible with the 8-lead package of Altera’s EEPROMs, refer to the AT17LV65/128/256/512/010/002/040
datasheet available on the Atmel web site for more information.
Package Type
8P3
8-lead, 0.300" Wide, Plastic Dual Inline Package (PDIP)
20J
20-lead, Plastic J-leaded Chip Carrier (PLCC)
32A
32-lead, Thin (1.0 mm) Plastic Quad Flat Package Carrier (TQFP)
13
2322G–CNFG–03/06
22.1
Standard Package Options(1)
Memory Size
Ordering Code
Package
Operation Range
AT17LV65A-10JC
20J
Commercial
(0°C to 70°C)
AT17LV65A-10JI
20J
Industrial
(-40°C to 85°C)
AT17LV128A-10JC
20J
Commercial
(0°C to 70°C)
AT17LV128A-10JI
20J
Industrial
(-40°C to 85°C)
AT17LV256A-10JC
20J
Commercial
(0°C to 70°C)
AT17LV256A-10JI
20J
Industrial
(-40°C to 85°C)
AT17LV512A-10PC
AT17LV512A-10JC
8P3
20J
Commercial
(0°C to 70°C)
AT17LV512A-10PI
AT17LV512A-10JI
8P3
20J
Industrial
(-40°C to 85°C)
AT17LV010A-10PC
AT17LV010A-10JC
AT17LV010A-10QC
8P3
20J
32A
Commercial
(0°C to 70°C)
AT17LV010A-10PI
AT17LV010A-10JI
AT17LV010A-10QI
8P3
20J
32A
Industrial
(-40°C to 85°C)
AT17LV002A-10JC
AT17LV002A-10QC
20J
32A
Commercial
(0°C to 70°C)
AT17LV002A-10JI
AT17LV002A-10QI
20J
32A
Industrial
(-40°C to 85°C)
64-Kbit(2)(7)
128-Kbit(7)
256-Kbit(3)(7)
512-Kbit(4)(7)
1-Mbit(5)(7)
2-Mbit(6)(7)
22.2
Notes:
Green Package Options (Pb/Halide-free/RoHS Compliant)(1)
Memory Size
Ordering Code
Package
Operation Range
512-Kbit(4)(7)
AT17LV512A-10JU
20J
Industrial
(-40°C to 85°C)
1-Mbit(5)(7)
AT17LV010A-10JU
AT17LV010A-10PU
20J
8P3
Industrial
(-40°C to 85°C)
2-Mbit(4)(7)
AT17LV002A-10JU
20J
Industrial
(-40°C to 85°C)
1. Currently, there are two types of low-density configurators. The new version will be identified by a “B” after the datacode. The
“B” version is fully backward-compatible with the original devices so existing customers will not be affected. The new parts
no longer require a MUX for ISP. See programming specification for more details.
2. Use 64-Kbit density parts to replace Altera EPC1064.
3. Use 256-Kbit density parts to replace Altera EPC1213.
4. Use 512-Kbit density parts to replace Altera EPC1441.
5. Use 1-Mbit density parts to replace Altera EPC1
6. Use 2-Mbit density parts to replace Altera EPC2. Atmel AT17LV002A devices do not support JTAG programming; Atmel
AT17LV002A devices use a 2-wire serial interface for in-system programming.
7. For operating voltage of 5V ±10%, please refer to the 5V ±10% AC and DC Characteristics.
14
AT17LV65A/128A/256A/512A/002A
2322G–CNFG–03/06
AT17LV65A/128A/256A/512A/002A
23. Packaging Information
23.1
8P3 – PDIP
E
1
E1
N
Top View
c
eA
End View
COMMON DIMENSIONS
(Unit of Measure = inches)
D
e
D1
A2 A
MIN
NOM
A2
0.115
0.130
0.195
b
0.014
0.018
0.022
5
b2
0.045
0.060
0.070
6
b3
0.030
0.039
0.045
6
c
0.008
0.010
0.014
D
0.355
0.365
0.400
D1
0.005
E
0.300
0.310
0.325
4
E1
0.240
0.250
0.280
3
SYMBOL
A
b2
b3
b
4 PLCS
Side View
L
Notes:
0.210
0.100 BSC
eA
0.300 BSC
0.115
NOTE
2
3
3
e
L
MAX
0.130
4
0.150
2
1. This drawing is for general information only; refer to JEDEC Drawing MS-001, Variation BA for additional information.
2. Dimensions A and L are measured with the package seated in JEDEC seating plane Gauge GS-3.
3. D, D1 and E1 dimensions do not include mold Flash or protrusions. Mold Flash or protrusions shall not exceed 0.010 inch.
4. E and eA measured with the leads constrained to be perpendicular to datum.
5. Pointed or rounded lead tips are preferred to ease insertion.
6. b2 and b3 maximum dimensions do not include Dambar protrusions. Dambar protrusions shall not exceed 0.010 (0.25 mm).
01/09/02
R
2325 Orchard Parkway
San Jose, CA 95131
TITLE
8P3, 8-lead, 0.300" Wide Body, Plastic Dual
In-line Package (PDIP)
DRAWING NO.
REV.
8P3
B
15
2322G–CNFG–03/06
23.2
20J – PLCC
PIN NO. 1
1.14(0.045) X 45˚
1.14(0.045) X 45˚
0.318(0.0125)
0.191(0.0075)
IDENTIFIER
e
E1
E
D2/E2
B1
B
A2
D1
A1
D
A
0.51(0.020)MAX
45˚ MAX (3X)
COMMON DIMENSIONS
(Unit of Measure = mm)
Notes:
SYMBOL
MIN
NOM
MAX
A
4.191
–
4.572
A1
2.286
–
3.048
A2
0.508
–
–
D
9.779
–
10.033
1. This package conforms to JEDEC reference MS-018, Variation AA.
2. Dimensions D1 and E1 do not include mold protrusion.
Allowable protrusion is .010"(0.254 mm) per side. Dimension D1
and E1 include mold mismatch and are measured at the extreme
material condition at the upper or lower parting line.
3. Lead coplanarity is 0.004" (0.102 mm) maximum.
D1
8.890
–
9.042
E
9.779
–
10.033
E1
8.890
–
9.042
D2/E2
7.366
–
8.382
B
0.660
–
0.813
B1
0.330
–
0.533
e
NOTE
Note 2
Note 2
1.270 TYP
10/04/01
R
16
2325 Orchard Parkway
San Jose, CA 95131
TITLE
20J, 20-lead, Plastic J-leaded Chip Carrier (PLCC)
DRAWING NO.
REV.
20J
B
AT17LV65A/128A/256A/512A/002A
2322G–CNFG–03/06
AT17LV65A/128A/256A/512A/002A
23.3
32A – TQFP
PIN 1
B
PIN 1 IDENTIFIER
E1
e
E
D1
D
C
0˚~7˚
A1
A2
A
L
COMMON DIMENSIONS
(Unit of Measure = mm)
Notes:
1. This package conforms to JEDEC reference MS-026, Variation ABA.
2. Dimensions D1 and E1 do not include mold protrusion. Allowable
protrusion is 0.25 mm per side. Dimensions D1 and E1 are maximum
plastic body size dimensions including mold mismatch.
3. Lead coplanarity is 0.10 mm maximum.
SYMBOL
MIN
NOM
MAX
A
–
–
1.20
A1
0.05
–
0.15
A2
0.95
1.00
1.05
D
8.75
9.00
9.25
D1
6.90
7.00
7.10
E
8.75
9.00
9.25
E1
6.90
7.00
7.10
B
0.30
–
0.45
C
0.09
–
0.20
L
0.45
–
0.75
e
NOTE
Note 2
Note 2
0.80 TYP
10/5/2001
R
2325 Orchard Parkway
San Jose, CA 95131
TITLE
32A, 32-lead, 7 x 7 mm Body Size, 1.0 mm Body Thickness,
0.8 mm Lead Pitch, Thin Profile Plastic Quad Flat Package (TQFP)
DRAWING NO.
REV.
32A
B
17
2322G–CNFG–03/06
Atmel Corporation
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 487-2600
Regional Headquarters
Europe
Atmel Sarl
Route des Arsenaux 41
Case Postale 80
CH-1705 Fribourg
Switzerland
Tel: (41) 26-426-5555
Fax: (41) 26-426-5500
Asia
Room 1219
Chinachem Golden Plaza
77 Mody Road Tsimshatsui
East Kowloon
Hong Kong
Tel: (852) 2721-9778
Fax: (852) 2722-1369
Japan
9F, Tonetsu Shinkawa Bldg.
1-24-8 Shinkawa
Chuo-ku, Tokyo 104-0033
Japan
Tel: (81) 3-3523-3551
Fax: (81) 3-3523-7581
Atmel Operations
Memory
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 436-4314
RF/Automotive
Theresienstrasse 2
Postfach 3535
74025 Heilbronn, Germany
Tel: (49) 71-31-67-0
Fax: (49) 71-31-67-2340
Microcontrollers
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 436-4314
La Chantrerie
BP 70602
44306 Nantes Cedex 3, France
Tel: (33) 2-40-18-18-18
Fax: (33) 2-40-18-19-60
ASIC/ASSP/Smart Cards
1150 East Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906, USA
Tel: 1(719) 576-3300
Fax: 1(719) 540-1759
Biometrics/Imaging/Hi-Rel MPU/
High Speed Converters/RF Datacom
Avenue de Rochepleine
BP 123
38521 Saint-Egreve Cedex, France
Tel: (33) 4-76-58-30-00
Fax: (33) 4-76-58-34-80
Zone Industrielle
13106 Rousset Cedex, France
Tel: (33) 4-42-53-60-00
Fax: (33) 4-42-53-60-01
1150 East Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906, USA
Tel: 1(719) 576-3300
Fax: 1(719) 540-1759
Scottish Enterprise Technology Park
Maxwell Building
East Kilbride G75 0QR, Scotland
Tel: (44) 1355-803-000
Fax: (44) 1355-242-743
Atmel Programmable SLI Hotline
Literature Requests
(408) 436-4119
www.atmel.com/literature
Atmel Programmable SLI e-mail
[email protected]
FAQ
Available on web site
Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any
intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY
WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT
OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no
representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications
and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided
otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use
as components in applications intended to support or sustain life.
© Atmel Corporation 2006. All rights reserved. Atmel®, logo and combinations thereof, Everywhere You Are®
and others, are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and
product names may be trademarks of others.
Printed on recycled paper.
2322G–CNFG–03/06