Features • Low-voltage and Standard-voltage Operation VCC = 1.7V to 5.5V • Internally Organized as 32,768 x 8 • Two-wire Serial Interface • Schmitt Trigger, Filtered Inputs for Noise Suppression • Bidirectional Data Transfer Protocol • Write Protect Pin for Hardware and Software Data Protection Two-wire Serial EEPROM • 64-byte Page Write Mode (Partial Page Writes Allowed) 256K (32,768 x 8) • 1 MHz (5.0V, 2.7V, 2.5V), and 400kHz (1.7V) Compatibility • Self-timed Write Cycle (5ms Max) • High Reliability Atmel AT24C256C Endurance: One Million Write Cycles Data Retention: 40 Years • Lead-free/Halogen-free Devices Available • 8-lead JEDEC SOIC, 8-lead TSSOP, 8-lead UDFN and 8-ball VFBGA Packages • Die Sales: Wafer Form, Waffle Pack and Bumped Wafers Description The AT24C256C provides 262,144-bits of serial electrically erasable and programmable read-only memory (EEPROM) organized as 32,768 words of eight bits each. The device’s cascadable feature allows up to eight devices to share a common two-wire bus. The device is optimized for use in many industrial and commercial applications where low-power and low-voltage operation are essential. The devices are available in space-saving 8-lead JEDEC SOIC, 8-lead TSSOP, 8-lead UDFN, and 8-ball VFBGA packages. In addition, this device operates from 1.7V to 5.5V. Table 1. Pin Configurations Pin Name A0 – A2 8-lead SOIC Function Address Inputs SDA Serial Data SCL Serial Clock Input WP Write Protect GND Ground A0 A1 A2 GND 8-lead TSSOP 1 8 VCC 2 7 3 6 4 5 WP SCL SDA 8-lead UDFN A0 A1 A2 GND 1 8 VCC 2 7 3 6 4 5 WP SCL SDA 8-ball VFBGA VCC 8 1 A0 VCC 8 1 WP 7 SCL 6 SDA 5 2 A1 WP 7 SCL 6 SDA 5 2 3 A2 4 GND Bottom View 3 4 A0 A1 A2 GND Bottom View 8568C–SEEPR–5/10 1. Absolute Maximum Ratings* Operating Temperature .......................... −55°C to +125°C Storage Temperature ........................... −65°C to + 150°C Voltage on Any Pin with Respect to Ground ............................... − 1.0 V +7.0V Maximum Operating Voltage ................................... 6.25V *NOTICE: Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification are not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. DC Output Current ................................................ 5.0 mA Figure 1-1. Block Diagram VCC GND WP START STOP LOGIC SERIAL CONTROL LOGIC LOAD DEVICE ADDRESS COMPARATOR A2 A1 A0 R/W EN H.V. PUMP/TIMING COMP LOAD DATA RECOVERY INC DATA WORD ADDR/COUNTER Y DEC X DEC SCL SDA EEPROM SERIAL MUX DOUT/ACK LOGIC DIN DOUT 2 Atmel AT24C256C 8568C–SEEPR–5/10 Atmel AT24C256C 2. Pin Descriptions SERIAL CLOCK (SCL): The SCL input is used to positive-edge clock data into each EEPROM device and negative-edge clock data out of each device. SERIAL DATA (SDA): The SDA pin is bidirectional for serial data transfer. This pin is open drain driven and may be wire-ORed with any number of other open-drain or open-collector devices. DEVICE/PAGE ADDRESSES (A2, A1, A0): The A2, A1, and A0 pins are device address inputs that are hardwired (directly to GND or to VCC) for compatibility with other Atmel® AT24Cxx devices. When the pins are hardwired, as many as eight 256K devices may be addressed on a single bus system. (Device addressing is discussed in detail under “Device Addressing”) A device is selected when a corresponding hardware and software match is true. If these pins are left floating, the A2, A1, and A0 pins will be internally pulled down to GND. However, due to capacitive coupling that may appear during customer applications, Atmel recommends always connecting the address pins to a known state. When using a pull-up resistor, Atmel recommends using 10kΩ or less. WRITE PROTECT (WP): The write protect input, when connected to GND, allows normal write operations. When WP is connected directly to VCC, all write operations to the memory are inhibited. If the pin is left floating, the WP pin will be internally pulled down to GND. However, due to capacitive coupling that may appear during customer applications, Atmel recommends always connecting the WP pins to a known state. When using a pull-up resistor, Atmel recommends using 10kΩ or less. 3 8568C–SEEPR–5/10 3. Memory Organization Atmel AT24C256C, 256K SERIAL EEPROM: The 256K is internally organized as 512 pages of 64-bytes each. Random word addressing requires a 15-bit data word address. Table 3-1. Pin Capacitance(1) Applicable over recommended operating range from: TA = 25°C, f = 1.0MHz, VCC = +1.7V Symbol Test Condition Max Units Conditions CI/O Input/Output Capacitance (SDA) 8 pF VI/O = 0V CIN Input Capacitance (A0, A1, SCL) 6 pF VIN = 0V Note: 1. This parameter is characterized and is not 100% tested Table 3-2. DC Characteristics Applicable over recommended operating range from: TAI = − 40°C to +85°C, VCC = +1.7V to +5.5V (unless otherwise noted) Symbol Test Condition Min Typ 1.7 Max Units 5.5 V VCC1 Supply Voltage ICC1 Supply Current VCC = 5.0V READ at 400kHz 1.0 2.0 mA ICC2 Supply Current VCC = 5.0V WRITE at 400kHz 2.0 3.0 mA Standby Current (1.7V option) VCC = 1.7V 1.0 µA ISB1 6.0 µA VIN = VCC or VSS VCC = 5.0V ILI Input Leakage Currentt VCC = 5.0V VIN = VCC or VSS 0.10 3.0 µA ILO Output Leakage Currentt VCC = 5.0V VOUT = VCC or VSS 0.05 3.0 µA VIL Input Low Level(1) -0.6 VCC x 0.3 V VCC x 0.7 VCC + 0.5 V (1) VIH Input High Level VOL2 Output Low Level VCC = 3.0V IOL = 2.1mA 0.4 V VOL1 Output Low Level VCC = 1.7V IOL = 0.15mA 0.2 V Note: 4 Parameter 1. VIL min and VIH max are reference only and are not tested Atmel AT24C256C 8568C–SEEPR–5/10 Atmel AT24C256C Table 3-3. AC Characteristics (Industrial Temperature) Applicable over recommended operating range from: TAI = − 40°C to +85°C, VCC = +1.7V to +5.5V, CL = 100 pF (unless otherwise noted). Test conditions are listed in Note 2. 1.7V Symbol 2.5, 5.0V Parameter Units Min Max Min 400 Max fSCL Clock Frequency, SCL tLOW Clock Pulse Width Low 1.3 0.4 µs tHIGH Clock Pulse Width High 0.6 0.4 µs tI Noise Suppression Time(1) tAA Clock Low to Data Out Valid 0.05 tBUF Time the bus must be free before a new transmission can start(1) 1.3 0.5 µs tHD.STA Start Hold Time 0.6 0.25 µs tSU.STA Start Set-up Time 0.6 0.25 µs tHD.DAT Data In Hold Time 0 0 µs tSU.DAT Data In Set-up Time 100 100 ns 100 0.9 50 ns 0.55 µs 0.3 µs 300 100 ns Inputs Rise Time (1) 0.05 kHz 0.3 (1) tR 1000 tF Inputs Fall Time tSU.STO Stop Set-up Time 0.6 0.25 µs tDH Data Out Hold Time 50 50 ns tWR Write Cycle Time 5 Endurance(1) 25°C, Page Mode, 3.3V 1,000,000 Note: 5 ms Write Cycles 1. This parameter is ensured by characterization and is not 100% tested 2. AC measurement conditions: - RL (connects to VCC): 1.3kΩ (2.5V, 5.5V), 10kΩ (1.7V) - Input pulse voltages: 0.3VCC to 0.7VCC - Input rise and fall times: ≤ 50ns - Input and output timing reference voltages: 0.5VCC 5 8568C–SEEPR–5/10 4. Device Operation CLOCK and DATA TRANSITIONS: The SDA pin is normally pulled high with an external device. Data on the SDA pin may change only during SCL low time periods (refer to Figure 2). Data changes during SCL high periods will indicate a start or stop condition as defined below. Figure 4-1. Data Validity SDA SCL DATA STABLE DATA STABLE DATA CHANGE START CONDITION: A high-to-low transition of SDA with SCL high is a start condition that must precede any other command (refer to Figure 2-2). Figure 4-2. Start and Stop Definition SDA SCL START STOP STOP CONDITION: A low-to-high transition of SDA with SCL high is a stop condition. After a read sequence, the stop command will place the EEPROM in a standby power mode (refer to Figure 3). ACKNOWLEDGE: All addresses and data words are serially transmitted to and from the EEPROM in 8-bit words. The EEPROM sends a “0” during the ninth clock cycle to acknowledge that it has received each word. STANDBY MODE: The Atmel® AT24C256C features a low-power standby mode that is enabled upon power-up and after the receipt of the stop bit and the completion of any internal operations. 6 Atmel AT24C256C 8568C–SEEPR–5/10 Atmel AT24C256C SOFTWARE RESET: After an interruption in protocol, power loss or system reset, any 2-wire part can be protocol reset by following these steps: a) b) c) Create a start bit condition, Clock nine cycles, Create another start bit followed by stop bit condition as shown below. The device is ready for next communication after above steps has been completed. Figure 4-3. Software Reset Dummy Clock Cycles Start bit SCL 1 2 3 Start bit 8 Stop bit 9 SDA Figure 4-4. Bus Timing tHIGH tF tR tLOW SCL tSU.STA tLOW tHD.STA tHD.DAT tSU.DAT tSU.STO SDA IN tAA tDH tBUF SDA OUT 7 8568C–SEEPR–5/10 Figure 4-5. Write Cycle Timing SCL SDA ACK 8th BIT WORDn (1) twr START CONDITION STOP CONDITION Note: 1. The write cycle time tWR is the time from a valid stop condition of a write sequence to the end of the internal clear/write cycle Figure 4-6. Output Acknowledge 1 SCL 8 9 DATA IN DATA OUT START 8 ACKNOWLEDGE Atmel AT24C256C 8568C–SEEPR–5/10 Atmel AT24C256C 5. Device Addressing The 256K EEPROM requires an 8-bit device address word following a start condition to enable the chip for a read or write operation (refer to Figure 8). The device address word consists of a mandatory “1”, “0” sequence for the first four most significant bits as shown. This is common to all two-wire EEPROM devices. Figure 5-1. 1 MSB Device Addressing 0 1 0 A2 A1 A0 R/W LSB The next three bits are the A2, A1, A0 device address bits to allow as many as eight devices on the same bus. These bits must compare to their corresponding hardwired input pins. The A2, A1, and A0 pins use an internal proprietary circuit that biases them to a logic low condition if the pins are allowed to float. The eighth bit of the device address is the read/write operation select bit. A read operation is initiated if this bit is high, and a write operation is initiated if this bit is low. Upon a compare of the device address, the EEPROM will output a “0”. If a compare is not made, the device will return to a standby state. DATA SECURITY: The Atmel® AT24C256C has a hardware data protection scheme that allows the user to write protect the whole memory when the WP pin is at VCC. 9 8568C–SEEPR–5/10 6. Write Operations BYTE WRITE: A write operation requires two 8-bit data word addresses following the device address word and acknowledgment. Upon receipt of this address, the EEPROM will again respond with a “0” and then clock in the first 8-bit data word. Following receipt of the 8-bit data word, the EEPROM will output a “0”. The addressing device, such as a microcontroller, must then terminate the write sequence with a stop condition. At this time the EEPROM enters an internally-timed write cycle, tWR, to the nonvolatile memory. All inputs are disabled during this write cycle and the EEPROM will not respond until the write is complete (refer to Figure 9). Figure 6-1. Note: Byte Write * = DON’T CARE bit PAGE WRITE: The 256K EEPROM is capable of 64-byte page writes. A page write is initiated the same way as a byte write, but the microcontroller does not send a stop condition after the first data word is clocked in. Instead, after the EEPROM acknowledges receipt of the first data word, the microcontroller can transmit up to 63 more data words. The EEPROM will respond with a “0” after each data word received. The microcontroller must terminate the page write sequence with a stop condition (refer to Figure 10). Figure 6-2. Note: Page Write * = DON’T CARE bit The data word address lower six bits are internally incremented following the receipt of each data word. The higher data word address bits are not incremented, retaining the memory page row location. When the word address, internally generated, reaches the page boundary, the following byte is placed at the beginning of the same page. If more than 64 data words are transmitted to the EEPROM, the data word address will “roll over” and previous data will be overwritten. The address “roll over” during write is from the last byte of the current page to the first byte of the same page. ACKNOWLEDGE POLLING: Once the internally-timed write cycle has started and the EEPROM inputs are disabled, acknowledge polling can be initiated. This involves sending a start condition followed by the device address word. The read/write bit is representative of the operation desired. Only if the internal write cycle has completed will the EEPROM respond with a “0”, allowing the read or write sequence to continue. 10 Atmel AT24C256C 8568C–SEEPR–5/10 Atmel AT24C256C 7. Read Operations Read operations are initiated the same way as write operations with the exception that the read/write select bit in the device address word is set to “1”. There are three read operations: current address read, random address read, and sequential read. CURRENT ADDRESS READ: The internal data word address counter maintains the last address accessed during the last read or write operation, incremented by one. This address stays valid between operations as long as the chip power is maintained. The address “roll over” during read is from the last byte of the last memory page, to the first byte of the first page. Once the device address with the read/write select bit set to “1” is clocked in and acknowledged by the EEPROM, the current address data word is serially clocked out. The microcontroller does not respond with an input “0” but does generate a following stop condition (refer to Figure 11). Figure 7-1. Current Address Read RANDOM READ: A random read requires a “dummy” byte write sequence to load in the data word address. Once the device address word and data word address are clocked in and acknowledged by the EEPROM, the microcontroller must generate another start condition. The microcontroller now initiates a current address read by sending a device address with the read/write select bit high. The EEPROM acknowledges the device address and serially clocks out the data word. The microcontroller does not respond with a “0” but does generate a following stop condition. (Refer to Figure 12) Figure 7-2. Note: Random Read * = DON’T CARE bit 11 8568C–SEEPR–5/10 SEQUENTIAL READ: Sequential reads are initiated by either a current address read or a random address read. After the microcontroller receives a data word, it responds with an acknowledge. As long as the EEPROM receives an acknowledge, it will continue to increment the data word address and serially clock out sequential data words. When the memory address limit is reached, the data word address will “roll over” and the sequential read will continue. The sequential read operation is terminated when the microcontroller does not respond with a “0” but does generate a following stop condition (refer to Figure 13). Figure 7-3. 12 Sequential Read Atmel AT24C256C 8568C–SEEPR–5/10 Atmel AT24C256C 8. Ordering Code Detail AT 2 4 C 2 5 6 C - S S H L - B Atmel Designator Shipping Carrier Option B or blank = Bulk (tubes) T = Tape and reel Product Family Operating Voltage L Device Density 256 = 256K Device Revision = 1.7V to 5.5V Package Device Grade or Wafer/Die Thickness H = Green, NiPdAu lead finish, Industrial Temperature Range (-40°C to +85°C) U = Green, matte Sn lead finish, Industrial Temperature Range (-40°C to +85°C) 11 = 11mil wafer thickness Package Option SS = JEDEC SOIC X = TSSOP MA = UDFN C = VFBGA WWU = Wafer unsawn WDT = Die in Tape and Reel 13 8568C–SEEPR–5/10 9. Part Markings Atmel AT24C256C-SSHL Top Mark Seal Year | Seal Week | | | |---|---|---|---|---|---|---|---| A T M L H Y W W |---|---|---|---|---|---|---|---| 2 E C L * LOT NUMBER |---|---|---|---|---|---|---|---| | PIN 1 INDICATOR (DOT) Y = SEAL YEAR 6: 2006 0: 7: 2007 1: 8: 2008 2: 9: 2009 3: 2010 2011 2012 2013 WW = SEAL WEEK 02 = Week 2 04 = Week 4 :: : :::: : :: : :::: :: 50 = Week 50 52 = Week 52 Lot Number to Use ALL Characters in Marking BOTTOM MARK No Bottom Mark Y = SEAL YEAR 6: 2006 0: 7: 2007 1: 8: 2008 2: 9: 2009 3: 2010 2011 2012 2013 Atmel AT24C256C-XHL Top Mark PIN 1 INDICATOR (DOT) | |---|---|---|---| * H Y W W |---|---|---|---|---| 2 E C L |---|---|---|---|---| Bottom Mark |---|---|---|---|---|---|---| X X |---|---|---|---|---|---|---| A A A A A A A <- PIN 1 INDICATOR WW 02 04 :: :: 50 52 = = = : : = = SEAL Week Week :::: :::: Week Week WEEK 2 4 : :: 50 52 WW 02 04 :: :: 50 52 = = = : : = = SEAL Week Week :::: :::: Week Week WEEK 2 4 : :: 50 52 XX = Country of Origin Atmel AT24C256C-MAHL Top Mark Seal Year | Seal Week | | | |---|---|---|---|---|---|---|---| A T M L H Y W W |---|---|---|---|---|---|---|---| 2 E C L LOT NUMBER |---|---|---|---|---|---|---|---| * | PIN 1 INDICATOR (DOT) 14 Y = SEAL YEAR 6: 2006 0: 7: 2007 1: 8: 2008 2: 9: 2009 3: 2010 2011 2012 2013 Atmel AT24C256C 8568C–SEEPR–5/10 Atmel AT24C256C Atmel AT24C256C-CUL Top Mark Line 1 -----------> Line 2 -----------> 2ECU YMTC | <--- PIN 1 INDICATOR (DOT) Y = ONE DIGIT YEAR CODE 4: 2004 7: 2007 5: 2005 8: 2008 6: 2006 9: 2009 M A B " J K L = = = " = = = SEAL MONTH (USE ALPHA DESIGNATOR A-L) JANUARY FEBRUARY """""""" OCTOBER NOVEMBER DECEMBER TC = TRACE CODE 15 8568C–SEEPR–5/10 10. Ordering Codes Atmel AT24C256C Ordering Information Ordering Code Voltage Package Operating Range AT24C256C-SSHL-B AT24C256C-SSHL-T(2) AT24C256C-XHL-B(1) AT24C256C-XHL-T(2) AT24C256C-MAHL-T(2) AT24C256C-CUL-T(2) 1.7V to 5.5V 1.7V to 5.5V 1.7V to 5.5V 1.7V to 5.5V 1.7V to 5.5V 1.7V to 5.5V 8S1 8S1 8A2 8A2 8MA2 8U2-1 Lead-free/Halogen-free Industrial Temperature (−40°C to 85°C) AT24C256C-WWU11L(3) 1.7V to 5.5V Die Sale Industrial Temperature (−40°C to 85°C) (1) Note: 1. Bulk delivery in tubes (SOIC and TSSOP 100/tube) 2. Tape and reel delivery (SOIC 4k/reel, TSSOP, UDFN and VFBGA 5k/reel) 3. Contact Atmel Sales for Wafer sales Package Type 16 8S1 8-lead, 0.150” Wide, Plastic Gull Wing Small Outline Package (JEDEC SOIC) 8A2 8-lead, 4.40mm Body, Plastic Thin Shrink Small Outline Package (TSSOP) 8MA2 8-lead, 2.00mm x 3.00mm Body, 0.50mm Pitch, Dual No Lead Package (UDFN) 8U2-1 8-ball, die Ball Grid Array Package (VFBGA) Atmel AT24C256C 8568C–SEEPR–5/10 Atmel AT24C256C 11. Packaging Information 8S1 – JEDEC SOIC END VIEW COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX A 1.35 – 1.75 A1 0.10 – 0.25 b 0.31 – 0.51 C 0.17 – 0.25 D 4.80 – 5.05 E1 3.81 – 3.99 E 5.79 – 6.20 e Notes: This drawing is for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc. L NOTE 1.27 BSC 0.40 – 1.27 0° – 8° 5/19/10 TITLE Package Drawing Contact: 8S1, 8-lead (0.150” Wide Body), Plastic Gull [email protected] Wing Small Outline (JEDEC SOIC) GPC SWB DRAWING NO. 8S1 REV. F 17 8568C–SEEPR–5/10 8A2 – TSSOP 3 2 1 Pin 1 indicator this corner E1 E L1 N L Top View End View COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL D A b e A2 NOM MAX NOTE 3.00 3.10 2, 5 3, 5 6.40 BSC E1 4.30 4.40 4.50 A – – 1.20 A2 0.80 1.00 1.05 b 0.19 – 0.30 e L Side View L1 4 0.65 BSC 0.45 0.60 0.75 1.00 REF 1. This drawing is for general information only. Refer to JEDEC Drawing MO-153, Variation AA, for proper dimensions, tolerances, datums, etc. 2. Dimension D does not include mold Flash, protrusions or gate burrs. Mold Flash, protrusions and gate burrs shall not exceed 0.15 mm (0.006 in) per side. 3. Dimension E1 does not include inter-lead Flash or protrusions. Inter-lead Flash and protrusions shall not exceed 0.25 mm (0.010 in) per side. 4. Dimension b does not include Dambar protrusion. Allowable Dambar protrusion shall be 0.08 mm total in excess of the b dimension at maximum material condition. Dambar cannot be located on the lower radius of the foot. Minimum space between protrusion and adjacent lead is 0.07 mm. 5. Dimension D and E1 to be determined at Datum Plane H. 5/19/10 TITLE Package Drawing Contact: 8A2, 8-lead 4.4mm Body, Plastic Thin [email protected] Shrink Small Outline Package (TSSOP) 18 2.90 E D Notes: MIN GPC TNR DRAWING NO. 8A2 REV. E Atmel AT24C256C 8568C–SEEPR–5/10 Atmel AT24C256C 8MA2 – UDFN E 1 8 Pin 1 ID 2 7 3 6 4 5 D C A2 A A1 E2 b (8x) 8 1 Pin#1 ID (R0.10) 7 0.35 COMMON DIMENSIONS (Unit of Measure = mm) 2 D2 6 3 5 4 e (6x) K L (8x) Notes: 1. This drawing is for general information only. Refer to JEDEC Drawing MO-229 for proper dimensions, tolerances, datums, etc. 2. The terminal #1 ID is a laser-marked feature. 3. Dimensions b applies to metalized terminal and is measured between 0.15 mm and 0.30 mm from the terminal tip. If the terminal has the optional radius on the other end of the terminal, the dimension should not be measured in that radius area. SYMBOL MIN D NOM MAX 2.00 BSC E 3.00 BSC D2 1.40 1.50 1.60 E2 1.20 1.30 1.40 A 0.50 0.55 0.60 A1 0.00 0.02 0.05 A2 – – 0.55 0.152 REF C L NOTE 0.30 e 0.40 0.35 0.50 BSC b 0.18 0.25 0.30 K 0.20 – – 3 4/15/08 TITLE Package Drawing Contact: [email protected] 8MA2, 8-pad, 2 x 3 x 0.6 mm Body, Thermally Enhanced Plastic Ultra Thin Dual Flat No Lead Package (UDFN) GPC YNZ DRAWING NO. REV. 8MA2 A 19 8568C–SEEPR–5/10 8U2-1 – VFBGA // 0.10 C 0.10 (4X) D A1 Ball Pad Corner 0.08 C C A Øb Ø0.15 M C A B Ø0.08 M C e A1 B A2 A Top View Side View A1 BALL PAD CORNER 2 1 A COMMON DIMENSIONS (Unit of Measure = mm) B e C D (e1) d SYMBOL MIN NOM MAX A 0.81 0.91 1.00 A1 0.15 0.20 0.25 A2 0.40 0.45 0.50 (d1) b 0.25 0.30 0.35 Bottom View D 2.35 BSC 8 SOLDER BALLS E 3.73 BSC e 0.75 BSC e1 0.74 BSC d 0.75 BSC d1 0.80 REF Notes: 1. This drawing is for general information. 2. Dimension 'b' is measured at the maximum solder ball diameter. 3. Solder ball composition shall be 95.5Sn-4.0Ag-.5Cu. NOTE 2/25/08 Package Drawing Contact: [email protected] 20 TITLE GPC 8U2-1, 8 ball, 2.35 x 3.73 mm Body, 0.75 mm pitch, VFBGA Package (dBGA2) GWW DRAWING NO. REV. 8U2-1 C Atmel AT24C256C 8568C–SEEPR–5/10 Atmel AT24C256C Appendix A. Revision History Doc. Rev. Date Comments 8568C 05/2010 Update 8S1 and 8A2 package drawings. 8568B 03/2010 Part Markings and ordering detail/codes updated. 8568A 09/2009 Initial document release 21 8568C–SEEPR–5/10 He ad q ua rt e rs In t er n at io n al Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131 USA Tel: (+1) (408) 441-0311 Fax: (+1) (408) 487-2600 www.atmel.com Atmel Asia Limited Unit 01-5 & 16, 19F BEA Tower, Millennium City 5 418 Kwun Tong Road Kwun Tong, Kowloon HONG KONG Tel: (+852) 2245-6100 Fax: (+852) 2722-1369 Atmel Munich GmbH Business Campus Parkring 4 D-85748 Garching bei Munich GERMANY Tel: (+49) 89-31970-0 Fax: (+49) 89-3194621 Atmel Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 JAPAN Tel: (+81) (3) 3523-3551 Fax: (+81) (3) 3523-7581 Sales Contact www.atmel.com/contacts Literature Requests www.atmel.com/literature P ro d u ct Co n t a ct Technical Support [email protected] Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDEN-TAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. © 2010 Atmel Corporation. All rights reserved. Atmel®, Atmel logo and combinations thereof, and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. 8568C–SEEPR–5/10