DC/DC Converters SPECIFICATIONS CTDD3120DF-T1K-3 Series Wide Input Isolated & Regulated 3W Output, Twin Output Not shown at actual size. RoHS Compliant ctparts.com Part Number Vin Nom. (VDC) Input Range (VDC) Vin Max.* (VDC) Vo1,Vo2 (VDC) CTDD3120DF-050505-T1K-3 CTDD3120DF-050909-T1K-3 CTDD3120DF-051212-T1K-3 CTDD3120DF-051515-T1K-3 5 5 5 5 4.5-9.0 4.5-9.0 4.5-9.0 4.5-9.0 11 11 11 11 5 9 12 15 CTDD3120DF-120505-T1K-3 CTDD3120DF-120909-T1K-3 CTDD3120DF-121212-T1K-3 CTDD3120DF-121515-T1K-3 12 12 12 12 9.0-18 9.0-18 9.0-18 9.0-18 22 22 22 22 CTDD3120DF-150505-T1K-3 CTDD3120DF-150909-T1K-3 CTDD3120DF-151212-T1K-3 CTDD3120DF-151515-T1K-3 15 15 15 15 12-24 12-24 12-24 12-24 CTDD3120DF-240505-T1K-3 CTDD3120DF-240909-T1K-3 CTDD3120DF-241212-T1K-3 CTDD3120DF-241515-T1K-3 24 24 24 24 CTDD3120DF-480505-T1K-3 CTDD3120DF-480909-T1K-3 CTDD3120DF-481212-T1K-3 CTDD3120DF-481515-T1K-3 48 48 48 48 Io1, Io2 Max. (mA) Io1, Io2 Min. (mA) Effi. Typ. (%) 300 160 125 100 30 16 13 10 72 74 78 78 5 9 12 15 300 160 125 100 30 16 13 10 73 77 79 79 30 30 30 30 5 9 12 15 300 160 125 100 30 16 13 10 74 78 79 79 18-36 18-36 18-36 18-36 40 40 40 40 5 9 12 15 300 160 125 100 30 16 13 10 77 79 80 80 36-72 36-72 36-72 36-72 80 80 80 80 5 9 12 15 300 160 125 100 30 16 13 10 77 80 81 81 *If Input voltage above specified may cause permanent damage to the device ISOLATION SPECIFICATIONS FEATURES Efficiency: To 85% Temperature Range: -40°C to +85°C Package: UL94-V0 Isolation: 1KVDC Miscellaneous: Wide (2:1) Input Range. No heat sink required. Industry Standard Pinout. Twin Isolated Output. Custom service available. Samples available. CHARACTERISTICS Test Condition MIN Isolation Voltage Flash tested for 1 minute 1000 VDC Test at 500VDC 1000 MΩ Isolation Resistance Test Condition 3W Output Power Units MIN TYP MAX Units 3 W ±1 ±3 % Output voltage accuracy Refer to Recommended Circuit Load regulation From 10% to 100% load ±0.5 ±1 % Line regulation Input Voltage from low to high ±0.2 ±0.5 % Temperature drift (Vout) Refer to Temp. Derating Graph Ripple 20Hz to 300kHz Bandwidth Noise DC-20MHz Bandwidth Switching frequency 100% load, nominal input voltage 80 Switching frequency 10% load, nominal input voltage 250 0.03 %/°C 30 60 mVp-p 80 150 mVp-p 200 KHz 600 KHz Note: 1. All specifications measured at TA=25°C, humidity<75%, nominal input voltage and rated output unless otherwise specified. TYPICAL CHARACTERISTICS Temperature Derating Graph 120 100 80 60 Safe Operating Area 40 20 0 120 40 71 85 Ambient Temperature (°C) 12.20.06 Technologies MAX 0.3 0 -40 CENTRAL TYP OUTPUT SPECIFICATIONS Item Output Power (%) Output Short Circuit Protection: Continuous Temperature Rise at Full Load: 30°C (Typ.) Cooling: Free air convection No Load, Power Consumption: 100mW (typical) Operating Temperature Range: -40°C to +85°C Storage Temperature Range: -55°C to +125°C Lead Temperature: 300°C (1.5mm from case for 10 seconds) Storage Humidity Range: < 95% Case Material: Plastic (UL94-V0) MTBF: >3,500,000 hours Miscellaneous: RoHS Compliant. Item Manufacturer of Passive and Discrete Semiconductor Components 800-684-5322 Inside US 949-453-1811 Outside US Copyright © 2006 by CT Magnetics, DBA Central Technologies. All rights reserved. CT Magnetics reserves the right to make improvements or change specifications without notice DC/DC Converters ctparts.com CTDD3120DF-T1K-3 Series Wide Input Isolated & Regulated 3W Output, Twin Output OUTLINE DIMENSIONS & RECOMMENDED FOOTPRINT DETAILS CTDD3120DF-T1K-3 Package 2 Bottom View Side View 31.80 9.45 3 0.50 9 10 11 15.24 20.30 23 22 16 15 14 2.54 5.08 4.00 22.86 Note: All pins on a 2.54mm pitch; all pin diameters are 0.50mm; all dimensions in mm. (Tolerance:±0.25) PIN CONNECTIONS Bottom View 2 3 9 10 11 23 22 16 15 14 Pin Function 2, 3 14 16 11 9 22, 23 GND Vo1 0V1 Vo2 0V2 Vin RECOMMENDED CIRCUIT All the CTDD3120DF-T1K-3 Series have been tested according to the following recommended testing circuit before leaving factory. This series should be tested under load. Never be tested under no load (See figure 1 & 2). If you want to further decrease the input/output ripple, you can increase capacitance properly or choose capacitors with low ESR. However, the capacitance should not be too high (See table 1). If you want to use the products in high EMI, please choose our metal packaged products. External Capacitor Table (table 1) Figure 2 5V & 12V 24V & 48V C in 100µF C out (0+70°C) 100µF (electrolytic capacitor) C out (-40+85°C) 47µF (tantalum capacitor) Figure 1 lp + CS CAP CS PIN Vin DC +Cin 10µF GND Cout + Cout + DC DC 0V1 Vout1 Vout2 Input Current (A) Vin 0V2 CENTRAL Technologies 12.20.06 Manufacturer of Passive and Discrete Semiconductor Components 800-684-5322 Inside US 949-453-1811 Outside US Copyright © 2006 by CT Magnetics, DBA Central Technologies. All rights reserved. CT Magnetics reserves the right to make improvements or change specifications without notice Input Voltage Range Input Voltage (V)