DS3680 QUAD TELEPHONE RELAY DRIVER SLRS014C – MARCH 1986 – REVISED SEPTEMBER 1995 • • • • • • • • D OR N PACKAGE (TOP VIEW) Designed for – 52-V Battery Operation 50-mA Output Current Capability Input Compatible With TTL and CMOS High Common-Mode Input Voltage Range Very Low Input Current Fail-Safe Disconnect Feature Built-in Output Clamp Diode Direct Replacement for National DS3680 and Fairchild µA3680 description 1 IN + 1 IN – 2 IN – 2 IN + 3 IN + 3 IN – 4 IN – 1 14 2 13 3 12 4 11 5 10 6 9 7 8 BAT GND 1 OUT 2 OUT 3 OUT 4 OUT BAT NEG 4 IN + symbol (each driver) The DS3680 telephone relay driver is a monolithic integrated circuit designed to interface – 48-V relay systems to TTL or other systems in telephone applications. It is capable of sourcing up to 50 mA from standard – 52-V battery power. To reduce the effects of noise and IR drop between logic ground and battery ground, these drivers are designed to operate with a common-mode input range of ± 20 V referenced to battery ground. The common-mode input voltages for the four drivers can be different, so a wide range of input elements can be accommodated. The high-impedance inputs are compatible with positive TTL and CMOS levels or negative logic levels. A clamp network is included in the driver outputs to limit high-voltage transients generated by the relay coil during switching. The complementary inputs ensure that the driver output is off as a fail-safe condition when either output is open. BAT GND IN + + IN – – OUT BAT NEG schematic diagram (each driver) IN + 15 kΩ BAT GND IN – The DS3680 is characterized for operation from 0°C to 70°C. OUT BAT NEG All resistor values shown are nominal. Copyright 1995, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 DS3680 QUAD TELEPHONE RELAY DRIVER SLRS014C – MARCH 1986 – REVISED SEPTEMBER 1995 absolute maximum ratings over operating free-air temperature range (unless otherwise noted) Supply voltage range at BAT NEG, VBAT – (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 70 V to 0.5 V Input voltage range with respect to BAT GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 70 V to 20 V Input voltage range with respect to BAT NEG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.5 V to 70 V Differential input voltage, VID (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 20 V Output current, IO: Resistive load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 100 mA Inductive load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 50 mA Inductive output load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 H Continuous total dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table Operating free-air temperature range, TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C Lead temperature 1,6 mm (1/16 inch) from case for 60 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C NOTES: 1. All voltages are with respect to BAT GND, unless otherwise specified. 2. Differential input voltages are at the noninverting input terminal IN + with respect to the inverting input terminal IN –. DISSIPATION RATING TABLE TA ≤ 25°C POWER RATING DERATING FACTOR ABOVE TA = 25°C TA = 70°C POWER RATING D 950 mW 7.6 mW/°C 608 mW N 1150 mW 9.2 mW/°C 736 mW PACKAGE recommended operating conditions Supply voltage, VBAT – Input voltage, either input High-level differential input voltage, VIDH Low-level differential input voltage, VIDL MIN MAX UNIT – 10 – 20† – 60 V 20 V 2 † – 20 20 V 0.8 V Operating free-air temperature, TA 0 70 °C † The algebraic convention, in which the less positive (more negative) limit is designated minimum, is used in this data sheet for input voltage levels. electrical characteristics over recommended operating free-air temperature range, VBAT– = –52 V (unless otherwise noted) PARAMETER TEST CONDITIONS IIH High level input current (into IN + ) High-level VID = 2 V VID = 7 V IIL Low level input current (into IN + ) Low-level VID = 0.4 V VID = – 7 V VO(on) On-stage output voltage IO = 50 mA, IO(off) O( ff) Off stage output current Off-stage VO = VBAT – IR Clamp diode reverse current VOK Output clamp voltage VO = 0 IO = 50 mA IO = – 50 mA, All drivers on IBAT(on) On-state battery current IBAT(off) Off-state battery current ‡ All typical values are at TA = 25°C. 2 All drivers off POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 MIN TYP‡ MAX 40 100 375 1000 0.01 5 –1 – 100 VID = 2 V VID = 0.8 V – 1.6 – 2.1 –2 – 100 Inputs open –2 – 100 2 100 VBAT – = 0 0.9 1.2 – 0.9 – 1.2 UNIT µA µA V µA µA V –2 – 4.4 mA –1 – 100 µA DS3680 QUAD TELEPHONE RELAY DRIVER SLRS014C – MARCH 1986 – REVISED SEPTEMBER 1995 switching characteristics VBAT– = –52 V, TA = 25°C PARAMETER ton toff TEST CONDITIONS Turn-on time VID = 3-V pulse, L = 1 H, Turn-off time MIN RL = 1 kΩ, See Figure 2 TYP MAX 1 10 UNIT µs 1 10 µs PARAMETER MEASUREMENT INFORMATION BAT GND II + VI IO Load – BAT NEG VO – 52 V – 52 V Figure 1. Generalized Test Circuit, Each Driver BAT GND + Input Output – RL = 1 kΩ BAT NEG L=1H – 52 V TEST CIRCUIT 3V Input – 1.5 V 0V ton toff VO(on) Output – 25 V – 25 V VOLTAGE WAVEFORMS ≈ – 52 V Figure 2. Test Circuit and Voltage Waveforms, Each Driver POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 DS3680 QUAD TELEPHONE RELAY DRIVER SLRS014C – MARCH 1986 – REVISED SEPTEMBER 1995 APPLICATION INFORMATION 52-V Battery + – SN74XX 9 DS3680 1 2 3 4 5 6 8 7 K1 BAT NEG 1 IN + 1 IN – 13 2 IN + 1 OUT 2 IN – K2 3 IN + 3 IN – 12 4 IN + 2 OUT 4 IN – K3 ControlSignal Source 11 3 OUT K4 10 4 OUT K1 – K4 50-V Relay Coils – 50 mA MAX BAT GND 14 Figure 3. Relay Driver 4 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 PACKAGE OPTION ADDENDUM www.ti.com 30-Jan-2016 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (°C) Device Marking (4/5) DS3680D ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 0 to 70 DS3680 DS3680DE4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 0 to 70 DS3680 DS3680N ACTIVE PDIP N 14 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type 0 to 70 DS3680N (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 30-Jan-2016 continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2016, Texas Instruments Incorporated