TC74AC109P/F/FN TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic TC74AC109P,TC74AC109F,TC74AC109FN Dual J-K Flip Flop with Preset and Clear Note: The TC74AC109 is an advanced high speed CMOS DUAL J- K FLIP FLOP fabricated with silicon gate and double-layer metal wiring C2MOS technology. It achieves the high speed operation similar to equivalent Bipolar Schottky TTL while maintaining the CMOS low power dissipation. In accordance with the logic level given J and K input this device changes state on positive going transition of the clock pulse. CLEAR and PRESET are independent of the clock and accomplished by a low logic level on the corresponding input. All inputs are equipped with protection circuits against static discharge or transient excess voltage. xxxFN (JEDEC SOP) is not available in Japan. TC74AC109P TC74AC109F Features • High speed: fmax = 200 MHz (typ.) at VCC = 5 V • Low power dissipation: ICC = 4 μA (max) at Ta = 25°C • High noise immunity: VNIH = VNIL = 28% VCC (min) • Symmetrical output impedance: |IOH| = IOL = 24 mA (min) • Capability of driving 50 Ω transmission lines. ∼ tpHL Balanced propagation delays: tpLH − • Wide operating voltage range: VCC (opr) = 2 to 5.5 V • Pin and function compatible with 74F109 TC74AC109FN Pin Assignment Weight DIP16-P-300-2.54A SOP16-P-300-1.27A SOL16-P-150-1.27 1 : 1.00 g (typ.) : 0.18 g (typ.) : 0.13 g (typ.) 2007-10-01 TC74AC109P/F/FN IEC Logic Symbol Truth Table Inputs Outputs CLR PR J K CK Q Q Function L H X X X L H Clear H L X X X H L Preset L L X X X H H H H L H Qn Qn H H L L L H H H H H H L H H H L Qn Qn Toggle H H X X Qn Qn No Change No Change X: Don’t care System Diagram 2 2007-10-01 TC74AC109P/F/FN Absolute Maximum Ratings (Note 1) Characteristics Symbol Rating Unit Supply voltage range VCC −0.5 to 7.0 V DC input voltage VIN −0.5 to VCC + 0.5 V VOUT −0.5 to VCC + 0.5 V Input diode current IIK ±20 mA Output diode current IOK ±50 mA DC output current IOUT ±50 mA DC VCC/ground current ICC ±100 mA Power dissipation PD 500 (DIP) (Note 2)/180 (SOP) mW Storage temperature Tstg −65 to 150 °C DC output voltage Note 1: Exceeding any of the absolute maximum ratings, even briefly, lead to deterioration in IC performance or even destruction. Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings and the operating ranges. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (“Handling Precautions”/Derating Concept and Methods) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Note 2: 500 mW in the range of Ta = −40 to 65°C. From Ta = 65 to 85°C a derating factor of −10 mW/°C should be applied up to 300 mW. Operating Ranges (Note) Characteristics Symbol Rating Unit Supply voltage VCC 2.0 to 5.5 V Input voltage VIN 0 to VCC V VOUT 0 to VCC V Operating temperature Topr −40 to 85 °C Input rise and fall time dt/dV Output voltage Note: 0 to 100 (VCC = 3.3 ± 0.3 V) 0 to 20 (VCC = 5 ± 0.5 V) ns/V The operating ranges must be maintained to ensure the normal operation of the device. Unused inputs must be tied to either VCC or GND. 3 2007-10-01 TC74AC109P/F/FN Electrical Characteristics DC Characteristics High-level input voltage Low-level input voltage Symbol VIH VIL VCC (V) Min Typ. Max Min Max 2.0 1.50 ⎯ ⎯ 1.50 ⎯ 3.0 2.10 ⎯ ⎯ 2.10 ⎯ 5.5 3.85 ⎯ ⎯ 3.85 ⎯ 2.0 ⎯ ⎯ 0.50 ⎯ 0.50 3.0 ⎯ ⎯ 0.90 ⎯ 0.90 5.5 ⎯ ⎯ 1.65 ⎯ 1.65 2.0 1.9 2.0 ⎯ 1.9 ⎯ 3.0 2.9 3.0 ⎯ 2.9 ⎯ 4.5 4.4 4.5 ⎯ 4.4 ⎯ 3.0 2.58 ⎯ ⎯ 2.48 ⎯ 4.5 3.94 ⎯ ⎯ 3.80 ⎯ 5.5 ⎯ ⎯ ⎯ 3.85 ⎯ 2.0 ⎯ 0.0 0.1 ⎯ 0.1 IOL = 50 μA 3.0 ⎯ 0.0 0.1 ⎯ 0.1 VIN = VIH or IOL = 12 mA VIL 4.5 ⎯ 0.0 0.1 ⎯ 0.1 3.0 ⎯ ⎯ 0.36 ⎯ 0.44 4.5 ⎯ ⎯ 0.36 ⎯ 0.44 5.5 ⎯ ⎯ ⎯ ⎯ 1.65 ⎯ ⎯ IOH = −50 μA High-level output voltage VOH VIN = VIH or IOH = −4 mA VIL IOH = −24 mA IOH = −75 mA Low-level output voltage VOL Ta = −40 to 85°C Ta = 25°C Test Condition Characteristics (Note) IOL = 24 mA IOL = 75 mA (Note) Unit V V V V Input leakage current IIN VIN = VCC or GND 5.5 ⎯ ⎯ ±0.1 ⎯ ±1.0 μA Quiescent supply current ICC VIN = VCC or GND 5.5 ⎯ ⎯ 4.0 ⎯ 40.0 μA Note: This spec indicates the capability of driving 50 Ω transmission lines. One output should be tested at a time for a 10 ms maximum duration. 4 2007-10-01 TC74AC109P/F/FN Timing Requirements (input: tr = tf = 3 ns) Characteristics Symbol Minimum pulse width tW (L) (CK) tW (H) Minimum pulse width ⎯ tW (L) ⎯ Minimum set-up time ts ⎯ Minimum hold time th ⎯ trem ⎯ ( CLR , PR ) Minimum removal time ( CLR , PR ) Ta = 25°C Ta = −40 to 85°C VCC (V) Limit Limit 3.3 ± 0.3 8.0 8.0 5.0 ± 0.5 5.0 5.0 3.3 ± 0.3 7.0 7.0 5.0 ± 0.5 5.0 5.0 3.3 ± 0.3 9.0 9.0 5.0 ± 0.5 5.0 5.0 3.3 ± 0.3 0.0 0.0 5.0 ± 0.5 0.0 0.0 3.3 ± 0.3 3.0 3.0 5.0 ± 0.5 2.0 2.0 Test Condition Unit ns ns ns ns ns AC Characteristics (CL = 50 pF, RL = 500 Ω, input: tr = tf = 3 ns) Characteristics Symbol Propagation delay time tpLH (CK-Q, Q ) tpHL Propagation delay time tpLH ( CLR , PR -Q, Q ) tpHL Maximum clock frequency fmax Input capacitance CIN Power dissipation capacitance CPD Note: (Note) Ta = −40 to 85°C Ta = 25°C Test Condition Unit VCC (V) Min Typ. Max Min Max 3.3 ± 0.3 ⎯ 8.2 13.9 1.0 16.0 5.0 ± 0.5 ⎯ 6.1 8.7 1.0 10.0 3.3 ± 0.3 ⎯ 8.5 14.4 1.0 16.6 5.0 ± 0.5 ⎯ 6.4 9.1 1.0 10.5 3.3 ± 0.3 55 120 ⎯ 55 ⎯ 5.0 ± 0.5 100 160 ⎯ 100 ⎯ ⎯ ⎯ 5 10 ⎯ 10 pF ⎯ ⎯ 82 ⎯ ⎯ ⎯ pF ⎯ ⎯ ⎯ ns ns MHz CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption without load. Average operating current can be obtained by the equation: ICC (opr) = CPD･VCC･fIN + ICC/2 (per F/F) 5 2007-10-01 TC74AC109P/F/FN Package Dimensions Weight: 1.00 g (typ.) 6 2007-10-01 TC74AC109P/F/FN Package Dimensions Weight: 0.18 g (typ.) 7 2007-10-01 TC74AC109P/F/FN Package Dimensions (Note) Note: This package is not available in Japan. Weight: 0.13 g (typ.) 8 2007-10-01 TC74AC109P/F/FN RESTRICTIONS ON PRODUCT USE 20070701-EN GENERAL • The information contained herein is subject to change without notice. • TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc. • The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.).These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in his document shall be made at the customer’s own risk. • The products described in this document shall not be used or embedded to any downstream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulations. • The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patents or other rights of TOSHIBA or the third parties. • Please contact your sales representative for product-by-product details in this document regarding RoHS compatibility. Please use these products in this document in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses occurring as a result of noncompliance with applicable laws and regulations. 9 2007-10-01