AD AD737 Low cost, low power, true rms-to-dc converter Datasheet

a
FEATURES
COMPUTES
True RMS Value
Average Rectified Value
Absolute Value
PROVIDES
200 mV Full-Scale Input Range
(Larger Inputs with Input Attenuator)
Direct Interfacing with 3 1/2 Digit
CMOS A/D Converters
High Input Impedance of 1012 ⍀
Low Input Bias Current: 25 pA max
High Accuracy: ⴞ0.2 mV ⴞ0.3% of Reading
RMS Conversion with Signal Crest Factors Up to 5
Wide Power Supply Range: +2.8 V, –3.2 V to ⴞ16.5 V
Low Power: 160 ␮A max Supply Current
No External Trims Needed for Specified Accuracy
AD736—A General Purpose, Buffered Voltage
Output Version Also Available
PRODUCT DESCRIPTION
The AD737 is a low power, precision, monolithic true rms-to-dc
converter. It is laser trimmed to provide a maximum error of
± 0.2 mV ± 0.3% of reading with sine-wave inputs. Furthermore,
it maintains high accuracy while measuring a wide range of
input waveforms, including variable duty cycle pulses and triac
(phase) controlled sine waves. The low cost and small physical
size of this converter make it suitable for upgrading the performance of non-rms “precision rectifiers” in many applications.
Compared to these circuits, the AD737 offers higher accuracy at
equal or lower cost.
The AD737 can compute the rms value of both ac and dc input
voltages. It can also be operated ac coupled by adding one external capacitor. In this mode, the AD737 can resolve input signal levels of 100 µV rms or less, despite variations in temperature
or supply voltage. High accuracy is also maintained for input
waveforms with crest factors of 1 to 3. In addition, crest factors
as high as 5 can be measured (while introducing only 2.5%
additional error) at the 200 mV full-scale input level.
The AD737 has no output buffer amplifier, thereby significantly
reducing dc offset errors occuring at the output. This allows the
device to be highly compatible with high input impedance A/D
converters.
Requiring only 160 µA of power supply current, the AD737 is
optimized for use in portable multimeters and other battery
powered applications. This converter also provides a “power
down” feature which reduces the power supply standby current
to less than 30 µA.
Low Cost, Low Power,
True RMS-to-DC Converter
AD737*
FUNCTIONAL BLOCK DIAGRAM
AD737
8kV
CC
1
VIN
2
POWER
DOWN
3
8
FULL
WAVE
RECTIFIER
INPUT
AMPLIFIER
BIAS
SECTION
–VS 4
RMS CORE
8kV
COM
7 +VS
6 OUTPUT
5 CAV
The AD737 allows the choice of two signal input terminals: a
high impedance (1012 Ω) FET input which will directly interface
with high Z input attenuators and a low impedance (8 kΩ) input
which allows the measurement of 300 mV input levels, while
operating from the minimum power supply voltage of +2.8 V,
–3.2 V. The two inputs may be used either singly or differentially.
The AD737 achieves a 1% of reading error bandwidth exceeding 10 kHz for input amplitudes from 20 mV rms to 200 mV
rms while consuming only 0.72 mW.
The AD737 is available in four performance grades. The
AD737J and AD737K grades are rated over the commercial
temperature range of 0°C to +70°C. The AD737A and AD737B
grades are rated over the industrial temperature range of –40°C
to +85°C.
The AD737 is available in three low-cost, 8-lead packages: plastic DIP, plastic SO and hermetic cerdip.
PRODUCT HIGHLIGHTS
1. The AD737 is capable of computing the average rectified
value, absolute value or true rms value of various input
signals.
2. Only one external component, an averaging capacitor, is
required for the AD737 to perform true rms measurement.
3. The low power consumption of 0.72 mW makes the AD737
suitable for many battery powered applications.
*Protected under U.S. Patent Number 5,495,245.
REV. C
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
World Wide Web Site: http://www.analog.com
Fax: 781/326-8703
© Analog Devices, Inc., 1999
(@ +25ⴗC, ⴞ5 V supplies, ac coupled with 1 kHz sine-wave input applied unless
AD737–SPECIFICATIONS otherwise noted.)
Model
Conditions
Min
V OUT =
TRANSFER FUNCTION
CONVERSION ACCURACY
Total Error, Internal Trim1
All Grades
AD737J/A
Typ
1 kHz Sine Wave
ac Coupled Using C C
0–200 mV rms
200 mV–1 V rms
TMIN-TMAX
A&B Grades
@ 200 mV rms
J&K Grades
@ 200 mV rms
vs. Supply Voltage
@ 200 mV rms Input
VS = ±5 V to ± 16.5 V
@ 200 mV rms Input
VS = ±5 V to ± 3 V
dc Reversal Error, dc Coupled @ 600 mV dc
Nonlinearity2, 0–200 mV
@ 100 mV rms
Total Error, External Trim
0–200 mV rms
ERROR vs. CREST FACTOR3
Crest Factor 1 to 3
CAV , CF = 100 µF
Crest Factor = 5
CAV , CF = 100 µF
INPUT CHARACTERISTICS
High Impedance Input (Pin 2)
Signal Range
Continuous rms Level
VS = +2.8 V, –3.2 V
Continuous rms Level
VS = ±5 V to ± 16.5 V
Peak Transient Input
VS = +2.8 V, –3.2 V
Peak Transient Input
VS = ±5 V
Peak Transient Input
VS = ±16.5 V
Input Resistance
Input Bias Current
VS = ±5 V
Low Impedance Input (Pin 1)
Signal Range
Continuous rms Level
VS = +2.8 V, –3.2 V
Continuous rms Level
VS = ±5 V to ± 16.5 V
Peak Transient Input
VS = +2.8 V, –3.2 V
Peak Transient Input
VS = ±5 V
Peak Transient Input
VS = ±16.5 V
Input Resistance
Maximum Continuous
Nondestructive Input
All Supply Voltages
Input Offset Voltage4
ac Coupled
J&K Grades
A&B Grades
vs. Temperature
vs. Supply
VS = ±5 V to ± 16.5 V
vs. Supply
VS = ±5 V to ± 3 V
OUTPUT CHARACTERISTICS
Output Voltage Swing
No Load
VS = +2.8 V, –3.2 V
No Load
VS = ±5 V
No Load
VS = ±16.5 V
Output Resistance
@ dc
FREQUENCY RESPONSE
High Impedance Input (Pin 2)
For 1% Additional Error
Sine-Wave Input
VIN = 1 mV rms
VIN = 10 mV rms
VIN = 100 mV rms
VIN = 200 mV rms
± 3 dB Bandwidth
Sine-Wave Input
VIN = 1 mV rms
VIN = 10 mV rms
VIN = 100 mV rms
VIN = 200 mV rms
Max
2
V OUT =
Avg.(V IN )
0.2/0.3
–1.2
AD737K/B
Typ
Min
0.4/0.5
ⴞ2.0
2
0.5/0.7
0
0
0
+0.06
–0.18
1.3
+0.25
0.1/0.2
0
0
0
0.7
2.5
ⴞ0.9
ⴞ4.0
6.4
± 2.7
± 1.7
± 3.8
± 11
8
8
50
80
0 to –1.6
0 to –3.3
0 to –4
6.4
–1.7
–3.4
–5
8
± mV/± % of Reading
% of Reading
0.3/0.5
± mV/± % of Reading
± % of Reading/°C
+0.06
–0.18
1.3
+0.25
0.1/0.2
+0.1
–0.3
2.5
+0.35
%/V
%/V
% of Reading
% of Reading
± mV/± % of Reading
0.7
2.5
200
1
1012
1
0.2/0.3
ⴞ2.0
0.007
+0.1
–0.3
2.5
+0.35
ⴞ0.9
ⴞ4.0
25
300
l
Units
Avg.(V IN )
0.2/0.2
–1.2
0.007
Max
% Additional Error
% Additional Error
200
1
± 2.7
1012
1
25
9.6
mV rms
V rms
V
V
V
kΩ
± 12
± 12
V p-p
ⴞ3
ⴞ3
30
150
ⴞ3
ⴞ3
30
150
mV
mV
µV/°C
µV/V
µV/V
9.6
9.6
6.4
± 1.7
± 3.8
± 11
8
8
50
80
0 to –1.6
0 to –3.3
0 to –4
6.4
–1.7
–3.4
–5
8
300
l
mV rms
V rms
V
V
V
Ω
pA
9.6
V
V
V
kΩ
1
6
37
33
1
6
37
33
kHz
kHz
kHz
kHz
5
55
170
190
5
55
170
190
kHz
kHz
kHz
kHz
–2–
REV. C
AD737
Model
FREQUENCY RESPONSE
Low Impedance Input (Pin 1)
For 1% Additional Error
VIN = 1 mV rms
VIN = 10 mV rms
VIN = 100 mV rms
VIN = 200 mV rms
± 3 dB Bandwidth
VIN = 1 mV rms
VIN = 10 mV rms
VIN = 100 mV rms
VIN = 200 mV rms
POWER SUPPLY
Operating Voltage Range
Quiescent Current
VIN = 200 mV rms, No Load
Power Down Mode Current
Conditions
Min
AD737J/A
Typ
Max
Min
AD737K/B
Typ
Max
Units
Sine-Wave Input
1
6
90
90
1
6
90
90
kHz
kHz
kHz
kHz
5
55
350
460
5
55
350
460
kHz
kHz
kHz
kHz
Sine-Wave Input
Zero Signal
Sine-Wave Input
Pin 3 Tied to +VS
TEMPERATURE RANGE
Operating, Rated Performance
Commercial (0°C to +70°C)
Industrial (–40°C to +85°C)
+2.8, –3.2 ± 5
120
170
25
± 16.5
160
210
40
+2.8, –3.2
AD737J
AD737A
±5
120
170
25
± 16.5
160
210
40
V
µA
µA
µA
AD737K
AD737B
NOTES
l
Accuracy is specified with the AD737 connected as shown in Figure 16 with capacitor C C.
2
Nonlinearity is defined as the maximum deviation (in percent error) from a straight line connecting the readings at 0 and 200 mV rms.
3
Error vs. Crest Factor is specified as additional error for a 200 mV rms signal. C.F. = V PEAK /V rms.
4
DC offset does not limit ac resolution.
Specifications are subject to change without notice.
Specifications shown in boldface are tested on all production units at final electrical test. Results from those tests are used to calculate outgoing quality levels.
ABSOLUTE MAXIMUM RATINGS 1
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 16.5 V
Internal Power Dissipation2 . . . . . . . . . . . . . . . . . . . . . 200 mW
Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output Short-Circuit Duration . . . . . . . . . . . . . . . . . Indefinite
Differential Input Voltage . . . . . . . . . . . . . . . . . . +VS and –VS
Storage Temperature Range (Q) . . . . . . –65°C to +150°C
Storage Temperature Range (N, R) . . . . . –65°C to +125°C
Operating Temperature Range
AD737J/K . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to +70°C
AD737A/B . . . . . . . . . . . . . . . . . . . . . . . . . . –40°C to +85°C
Lead Temperature Range (Soldering 60 sec) . . . . . . . . +300°C
ESD Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500 V
NOTES
1
Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
2
8-Lead Plastic DIP Package: θ JA = 165°C/W
8-Lead Cerdip Package: θJA = 110°C/W
8-Lead Small Outline Package: θ JA = 155°C/W
ORDERING GUIDE
Model
Temperature
Range
Package
Description
Package
Option
AD737AQ
AD737BQ
AD737JN
AD737JR
AD737JR-REEL
AD737JR-REEL7
AD737KN
AD737KR
AD737KR-REEL
AD737KR-REEL7
–40°C to +85°C
–40°C to +85°C
0°C to +70°C
0°C to +70°C
0°C to +70°C
0°C to +70°C
0°C to +70°C
0°C to +70°C
0°C to +70°C
0°C to +70°C
Cerdip
Cerdip
Plastic DIP
SOIC
13" Tape and Reel
7" Tape and Reel
Plastic DIP
SOIC
13" Tape and Reel
7" Tape and Reel
Q-8
Q-8
N-8
SO-8
SO-8
SO-8
N-8
SO-8
SO-8
SO-8
PIN CONFIGURATIONS
Plastic DIP (N-8), Cerdip (Q-8), SOIC (SO-8)
1
VIN
2
POWER
DOWN
3
–VS 4
REV. C
AD737
8kV
CC
–3–
8
INPUT
AMPLIFIER
BIAS
SECTION
FULL
WAVE
RECTIFIER
RMS CORE
8kV
COM
7 +VS
6 OUTPUT
5 CAV
AD737 –Typical Characteristics
Figure 1. Additional Error vs.
Supply Voltage
Figure 2. Maximum Input Level
vs. Supply Voltage
Figure 3. Power Down Current vs.
Supply Voltage
Figure 4. Frequency Response
Driving Pin 1
Figure 5. Frequency Response
Driving Pin 2
Figure 6. Additional Error vs.
Crest Factor vs. CAV
Figure 7. Additional Error vs.
Temperature
Figure 8. DC Supply Current vs.
RMS lnput Level
Figure 9. 23 dB Frequency vs.
RMS Input Level (Pin 2)
–4–
REV. C
Applying the AD737
Figure 10. Error vs. RMS Input
Voltage (Pin 2) Using Circuit
of Figure 21
Figure 13. Pin 2 Input Bias
Current vs. Supply Voltage
Figure 11. C AV vs. Frequency for
Specified Averaging Error
Figure 14. Settling Time vs. RMS
Input Level for Various Values of CAV
Figure 12. RMS Input Level vs.
Frequency for Specified Averaging
Error
Figure 15. Pin 2 Input Bias Current
vs. Temperature
CALCULATING SETTLING TIME USING FIGURE 14
TYPES OF AC MEASUREMENT
The graph of Figure 14 may be used to closely approximate the
time required for the AD737 to settle when its input level is reduced in amplitude. The net time required for the rms converter
to settle will be the difference between two times extracted from
the graph – the initial time minus the final settling time. As an
example, consider the following conditions: a 33 µF averaging
capacitor, an initial rms input level of 100 mV and a final (reduced) input level of 1 mV. From Figure 14, the initial settling
time (where the 100 mV line intersects the 33 µF line) is around
80 ms. The settling time corresponding to the new or final input
level of 1 mV is approximately 8 seconds. Therefore, the net
time for the circuit to settle to its new value will be 8 seconds
minus 80 ms which is 7.92 seconds. Note that, because of the
smooth decay characteristic inherent with a capacitor/diode
combination, this is the total settling time to the final value (i.e.,
not the settling time to 1%, 0.1%, etc., of final value). Also, this
graph provides the worst case settling time, since the AD737
will settle very quickly with increasing input levels.
The AD737 is capable of measuring ac signals by operating as
either an average responding or a true rms-to-de converter. As
its name implies, an average responding converter computes the
average absolute value of an ac (or ac and dc) voltage or current
by full wave rectifying and low-pass filtering the input signal;
this will approximate the average. The resulting output, a dc
“average” level, is then scaled by adding (or reducing) gain; this
scale factor converts the dc average reading to an rms equivalent
value for the waveform being measured. For example, the average absolute value of a sine-wave voltage is 0.636 that of VPEAK;
the corresponding rms value is 0.707 times VPEAK. Therefore,
for sine-wave voltages, the required scale factor is 1.11 (0.707
divided by 0.636).
REV. C
In contrast to measuring the “average” value, true rms measurement is a “universal language” among waveforms, allowing the
magnitudes of all types of voltage (or current) waveforms to be
compared to one another and to dc. RMS is a direct measure of
the power or heating value of an ac voltage compared to that of
dc: an ac signal of 1 volt rms will produce the same amount of
heat in a resistor as a 1 volt dc signal.
–5–
AD737
Table I. Error Introduced by an Average Responding Circuit When Measuring Common Waveforms
Waveform Type
1 Volt Peak
Amplitude
Crest Factor
(VPEAK /V rms)
True rms Value
Average Responding
Circuit Calibrated to
Read rms Value of
Sine Waves Will Read
% of Reading Error*
Using Average
Responding Circuit
Undistorted
Sine Wave
Symmetrical
Square Wave
Undistorted
Triangle Wave
1.414
0.707 V
0.707 V
0%
1.00
1.00 V
1.11 V
+11.0%
1.73
0.577 V
0.555 V
–3.8%
3
2
10
0.333 V
0.5 V
0.1 V
0.295 V
0.278 V
0.011 V
–11.4%
–44%
–89%
2
4.7
0.495 V
0.212 V
0.354 V
0.150 V
–28%
–30%
Gaussian
Noise (98% of
Peaks <1 V)
Rectangular
Pulse Train
SCR Waveforms
50% Duty Cycle
25% Duty Cycle
Mathematically, the rms value of a voltage is defined (using a
simplified equation) as:
V rms =
input (Pin 1). The high impedance input, with its low input
bias current, is well suited for use with high impedance input
attenuators. The input signal may be either dc or ac coupled
to the input amplifier. Unlike other rms converters, the AD737
permits both direct and indirect ac coupling of the inputs. AC
coupling is provided by placing a series capacitor between the
input signal and Pin 2 (or Pin 1) for direct coupling and
between Pin 1 and ground (while driving Pin 2) for indirect
coupling.
The output of the input amplifier drives a full-wave precision
rectifier, which in turn, drives the rms core. It is in the core that
the essential rms operations of squaring, averaging and square
rooting are performed, using an external averaging capacitor,
CAV. Without CAV, the rectified input signal travels through the
core unprocessed, as is done with the average responding connection (Figure 17).
A final subsection, the bias section, permits a “power down”
function. This reduces the idle current of the AD737 from 160
µA down to a mere 30 µA. This feature is selected by tying Pin
3 to the +VS terminal. In the average responding connection, all
of the averaging is carried out by an RC post filter consisting of
an 8 kΩ internal scale-factor resistor connected between Pins 6
and 8 and an external averaging capacitor, CF. In the rms circuit, this additional filtering stage helps reduce any output
ripple which was not removed by the averaging capacitor, CAV.
Avg.(V 2 )
This involves squaring the signal, taking the average, and then
obtaining the square root. True rms converters are “smart rectifiers”: they provide an accurate rms reading regardless of the
type of waveform being measured. However, average responding
converters can exhibit very high errors when their input signals
deviate from their precalibrated waveform; the magnitude of the
error will depend upon the type of waveform being measured.
As an example, if an average responding converter is calibrated
to measure the rms value of sine-wave voltages, and then is used
to measure either symmetrical square waves or de voltages, the
converter will have a computational error 11% (of reading)
higher than the true rms value (see Table I).
AD737 THEORY OF OPERATION
As shown by Figure 16, the AD737 has four functional subsections: input amplifier, full-wave rectifier, rms core and bias sections. The FET input amplifier allows both a high impedance,
buffered input (Pin 2) or a low impedance, wide-dynamic-range
CC
10mF
(OPTIONAL
8kV
CC
VIN
2
POWER
3
DOWN
–VS
AD737
1
FULL
WAVE
RECTIFIER
INPUT
AMPLIFIER
BIAS
SECTION
8
COM
CF
10mF
7 +VS
6
5
4
Since the external averaging capacitor, CAV, “holds” the rectified input signal during rms computation, its value directly affects the accuracy of the rms measurement, especially at low
frequencies. Furthermore, because the averaging capacitor appears across a diode in the rms core, the averaging time constant will increase exponentially as the input signal is reduced.
This means that as the input level decreases, errors due to
nonideal averaging will reduce while the time it takes for the circuit to settle to the new rms level will increase. Therefore, lower
input levels allow the circuit to perform better (due to increased
averaging) but increase the waiting time between measurements. Obviously, when selecting CAV, a trade-off between
computational accuracy and settling time is required.
(OPTIONAL)
8kV
RMS
CORE
RMS MEASUREMENT – CHOOSING THE OPTIMUM
VALUE FOR C AV
OUTPUT
VOUT
CAV
CAV
33mF
POSITIVE SUPPLY
0.1mF
COMMON
NEGATIVE SUPPLY
+VS
0.1mF
–VS
Figure 16. AD737 True RMS Circuit
–6–
REV. C
AD737
RAPID SETTLING TIMES VIA THE AVERAGE
RESPONDING CONNECTION (FIGURE 17)
AC MEASUREMENT ACCURACY AND CREST FACTOR
The crest factor of the input waveform is often overlooked when
determining the accuracy of an ac measurement. Crest factor is
defined as the ratio of the peak signal amplitude to the rms amplitude (C.F. = VPEAK/V rms). Many common waveforms, such
as sine and triangle waves, have relatively low crest factors (≥2).
Other waveforms, such as low duty cycle pulse trains and SCR
waveforms, have high crest factors. These types of waveforms
require a long averaging time constant (to average out the long
time periods between pulses). Figure 6 shows the additional error vs. crest factor of the AD737 for various values of CAV.
Because the average responding connection does not use an averaging capacitor, its settling time does not vary with input signal level; it is determined solely by the RC time constant of CF
and the internal 8 kΩ output scaling resistor.
SELECTING PRACTICAL VALUES FOR INPUT
COUPLING (C C), AVERAGING (CAV) AND FILTERING
(CF) CAPACITORS
Table II provides practical values of CAV and C F for several
common applications.
Table II. AD737 Capacitor Selection Chart
Application
rms
Input
Level
Figure 17. AD737 Average Responding Circuit
Figure 18 shows the typical output waveform of the AD737 with
a sine-wave input voltage applied. As with all real-world devices,
the ideal output of VOUT = VIN is never exactly achieved; instead, the output contains both a dc and an ac error component.
General Purpose
Average
Responding
SCR Waveform
Measurement
CF
Settling
Time*
to 1%
20 Hz
200 Hz
5
5
150 µF 10 µF 360 ms
15 µF 1 µF 36 ms
0–200 mV 20 Hz
200 Hz
5
5
33 µF 10 µF 360 ms
3.3 µF 1 µF 36 ms
General Purpose 0–1 V
rms Computation
DC ERROR, OUTPUT RIPPLE, AND AVERAGING
ERROR
Low
Max
CAV
Frequency Crest
Cutoff
Factor
(–3 dB)
20 Hz
200 Hz
None
None
33 µF 1.2 sec
3.3 µF 120 ms
0–200 mV 20 Hz
200 Hz
None
None
33 µF 1.2 sec
3.3 µF 120 ms
0–1 V
0–200 mV 50 Hz
60 Hz
5
5
100 µF 33 µF 1.2 sec
82 µF 27 µF 1.0 sec
0–100 mV 50 Hz
60 Hz
5
5
50 µF
47 µF
33 µF 1.2 sec
27 µF 1.0 sec
Audio
Applications
Figure 18. Output Waveform for Sine-Wave Input Voltage
Speech
0–200 mV 300 Hz
3
1.5 µF 0.5 µF 18 ms
As shown, the dc error is the difference between the average of
the output signal (when all the ripple in the output has been
removed by external filtering) and the ideal dc output. The dc
error component is therefore set solely by the value of averaging capacitor used–no amount of post filtering (i.e., using a
very large CF) will allow the output voltage to equal its ideal
value. The ac error component, an output ripple, may be easily
removed by using a large enough post filtering capacitor, CF.
Music
0–100 mV 20 Hz
10
100 µF 68 µF 2.4 sec
* Settling time is specified over the stated rms input level with the input signal increasing
from zero. Settling times will be greater for decreasing amplitude input signals.
The input coupling capacitor, CC, in conjunction with the 8 kΩ
internal input scaling resistor, determine the –3 dB low frequency rolloff. This frequency, FL, is equal to:
FL =
In most cases, the combined magnitudes of both the dc and ac error
components need to be considered when selecting appropriate values
for capacitors CAV and CF. This combined error, representing the
maximum uncertainty of the measurement is termed the “averaging
error” and is equal to the peak value of the output ripple plus the dc
error. As the input frequency increases, both error components decrease rapidly: if the input frequency doubles, the dc error and ripple
reduce to 1/4 and 1/2 their original values, respectively, and rapidly
become insignificant.
REV. C
1
2π(8,000)(TheValue of CC in Farads )
Note that at FL, the amplitude error will be approximately –30%
(–3 dB) of reading. To reduce this error to 0.5% of reading,
choose a value of CC that sets FL at one tenth the lowest frequency to be measured.
In addition, if the input voltage has more than 100 mV of dc
offset, than the ac coupling network at Pin 2 should be used in
addition to capacitor CC .
–7–
C1175b–0–12/99 (rev. C)
AD737–Applications Circuits
Figure 19. 3 1/2 Digit DVM Circuit
Figure 20. Battery Powered Operation for 200 mV max
RMS Full-Scale Input
Figure 21. External Scale Factor Trim
Figure 23. DC Coupled VOS and Scale Factor Trims
Figure 22. dB Output Connection
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
8-Lead Plastic DIP Package (N-8)
8-Lead Cerdip Package (Q-8)
PRINTED IN U.S.A.
8-Lead Small Outline Package (SO-8)
0.1968 (5.00)
0.1890 (4.80)
0.1574 (4.00)
0.1497 (3.80)
8
5
1
4
0.2440 (6.20)
0.2284 (5.80)
PIN 1
0.0196 (0.50)
3 458
0.0099 (0.25)
0.0500 (1.27)
BSC
0.0098 (0.25)
0.0040 (0.10)
SEATING
PLANE
0.0688 (1.75)
0.0532 (1.35)
0.0192 (0.49)
0.0138 (0.35)
88
0.0098 (0.25) 08 0.0500 (1.27)
0.0160 (0.41)
0.0075 (0.19)
–8–
REV. C