PRELIMINARY CM2400-02/03/04 Universal Serial Bus Transceiver with Level Translator Features Product Description • • The CM2400-02/03/04 Universal Serial Bus (USB) transceiver is fully compliant with the USB specification Rev 1.1 and 2.0. It supports a speed of 12Mbits/s (Full Speed Mode). • • • • • • • • • • Complies with USB Specification Rev 1.1 & 2.0 Supports full speed (12Mbit/sec.) and low speed (1.5Mbits/sec.) modes Integrated 5V to 3.3V regulator Used as a USB device transceiver or host transceiver VBUS disconnection indication through VP and VM outputs Two single-ended receivers with hysteresis USB Detection of VBUS via level translator Stable RCV output during SE0 condition Low power operation from VCC Supports 1.65V to 3.6V I/O voltage levels Full industrial operating range -40 to 85 °C Available in small HBCC-16 and TSSOP-16 packages Applications • • • • Wireless handsets Digital still cameras PDAs (Personal Digital Assistants) IAs (Information Appliances) An internal level shifter allows interface to Application Specific ICs (ASICs) and Programmable Logic Devices (PLD's) running at core voltages of 1.65V to 3.6V. The CM2400-02/03/04 features an internal 5V to 3.3V regulator which is used to power the USB transceiver via the USB supply VBUS. The CM2400-04 features a Mode Input pin (MODE) which allows the device to operate in either single or differential input mode. This device is ideal for portable electronic devices such as mobile phones, digital still cameras, PDAs (Personal Digital Assistants) and IAs (Information Appliances). The CM2400-02/03/04 is packaged in a small form-factor 16-lead HBCC or TSSOP package to conserve board space. Simplified Block Schematic Voltage Regulator VBUS VCC VREG OE VMO/FSEO VPO/VO SPND RCV SPEED MODE* LEVEL TRANSLATOR VPU ENUM D+ D- VP VM GND * MODE pin available on CM2400-04 only. © 2004 California Micro Devices Corp. All rights reserved. 08/24/04 430 N. McCarthy Blvd., Milpitas, CA 95035-5112 ● Tel: 408.263.3214 ● Fax: 408.263.7846 ● www.calmicro.com 1 PRELIMINARY CM2400-02/03/04 12 D+ VM 6 11 D- SPND 7 10 SPEED GND 8 9 3 RCV 2 OE 1 VCC CM2400-02TS/-03TS Top View HBCC-16 GND 17 16 15 14 D- SPND 5 10 D+ VM 4 11 VPO/VO VP 3 12 VMO/FSEO RCV 2 13 VREG OE 1 SPEED 5 4 VP 9 VCC VP VM 8 6 7 8 HBCC-16 GND 17 16 15 14 9 D- 10 D+ 11 VPO/VO 12 VMO/FSEO 13 VREG VBUS VPO/VO 7 MODE VMO/FSEO 13 6 VPU 14 4 5 ENUM OE RCV SPND SPEED VREG 3 VCC VBUS 15 VBUS 16 2 VPU 1 ENUM VPU ENUM GND PACKAGE / PINOUT DIAGRAM CM2400-04HB Bottom View CM2400-02HB/-03HB Bottom View Note: These drawings are not to scale. PIN DESCRIPTIONS HBCC-16 PINS TSSOP-16 PINS NAME 1 3 OE Input for Output Enable (Active low). Enables transceiver driver to transmit data on the USB bus. When OE pin = LOW, driver circuitry is enabled. 2 4 RCV Differential receiver output of D+ and D- input data lines. The output state of RCV is preserved and stable during an SE0 condition. 3 5 VP Single-ended D+ receiver output for detection of a single-ended zero or error conditions 4 6 VM Single-ended D- receiver output for detection of a single-ended zero or error conditions. 5 7 SPND Suspend input. Allows the device to enter a low power state while the USB is inactive. 6 8 MODE Mode input (CM2400-04). Selects between differential (VPO, VMO) and singleended mode (VO, FSEO). DESCRIPTION GND Ground input (CM2400-02/03). Supply voltage for digital I/O pins. Voltages supported: 1.65 to 3.6V. 7 9 VCC 8 10 SPEED 9 11 D- Negative USB data connection. 10 12 D+ Positive USB data connection. In full-speed connect mode, connect to VPU via a 1.5kΩ resistor. Tolerance of this resistor is defined in the USB specification REV 1.1 & 2.0 11 13 VPO/VO Driver data input. 12 14 VMO/FSEO Driver data input. 13 15 VREG Regulated supply voltage output during USB operation of VBUS. 1µF decoupling capacitor is required. 14 16 VBUS Supply voltage input. Can be directly connected to USB VBUS. 15 1 VPU Pull-up supply voltage. Pin function is controlled by input ENUM. Speed Input. If SPEED is logic '1', selects full speed. If SPEED is logic '0', selects low speed. SPEED changes slope rise and fall time on D+ and D-. © 2004 California Micro Devices Corp. All rights reserved. 2 430 N. McCarthy Blvd., Milpitas, CA 95035-5112 ● Tel: 408.263.3214 ● Fax: 408.263.7846 ● www.calmicro.com 08/24/04 PRELIMINARY CM2400-02/03/04 PIN DESCRIPTIONS (CONT’D) 16 2 ENUM 17 − GND Enumerate, allows software to control connection of the external pull-up via the level translator. If ENUM = LOW then VPU is floating. If ENUM = HIGH then VPU is internally connected to VREG. The ground terminal is connected to the exposed diepad (heatsink). Ordering Information PART NUMBERING INFORMATION Lead-free FInishing2 Standard FInishing PADS/ LEADS Package 16 16 Ordering Part Number1 Part Marking Ordering Part Number1 Part Marking HBCC-16 CM2400-02HB CM240002HB CM2400-02HA CM240002HA TSSOP-16 CM2400-02TS CM240002TS CM2400-02TR CM240002TR 16 HBCC-16 CM2400-03HB CM240003HB CM2400-03HA CM240003HA 16 TSSOP-16 CM2400-03TS CM240003TS CM2400-03TR CM240003TR 16 HBCC-16 CM2400-04HB CM240004HB CM2400-04HA CM240004HA Note 1: Parts are shipped in Tape & Reel form unless otherwise specified. Note 2: Lead-free, 100% tin plated. Specifications ABSOLUTE MAXIMUM RATINGS PARAMETER RATING UNITS ESD Protection (All Pins except D+/D- pins, HBM, See Note 1) +1000 V ESD Protection (D+/D- pins, HBM, See Note 1) +4000 V VBUS [GND - 0.5] to +5.5 V VCC [GND - 0.5] to +6.0 V [GND - 0.5] to [VCC + 0.5] V Storage Temperature Range -65 to +150 °C Operating Temperature Range Junction -40 to +150 °C VI (INPUT) Note 1: Equivalent to discharging a 100pF capacitor via a 1.5kΩ resistor (Human body model). STANDARD (RECOMMENDED) OPERATING CONDITIONS SYMBOL PARAMETER MIN TYP MAX UNITS VBUS USB VBUS Supply 4.0 5.0 5.5 V VCC DC System Supply 1.65 3.3 3.6 V DC Input Voltage 0 - VCC V Analog I/O Pins (D+, D-) 0 - 3.6 V -40 - +85 °C VI VI(AI/O) TA Ambient Operating Temperature Range © 2004 California Micro Devices Corp. All rights reserved. 08/24/04 430 N. McCarthy Blvd., Milpitas, CA 95035-5112 ● Tel: 408.263.3214 ● Fax: 408.263.7846 ● www.calmicro.com 3 PRELIMINARY CM2400-02/03/04 Specifications (cont’d) ELECTRICAL OPERATING CHARACTERISTICS (SEE NOTE 1) Supply Pins (VBUS = 4.0V to 5.5V; VCC = 1.65V to 3.6V) SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS VREG Regulated supply output Unloaded 3.0 3.3 3.6 V IBUS Operating supply current Full-speed TX and RX; CL=50pF on D+/D- outputs; Note 2 8 mA IBUS(IDLE) Supply current during full speed idle and SE0 Full-speed idle; Notes 3 & 4 500 µA IBUS(DIS) Disable mode supply current VCC not present; Note 4 60 µA SPND = HIGH; Notes 3 & 4 60 µA Operating I/O supply current Full-speed TX and RX; Note 5 1.0 mA Static I/O supply current Full-speed idle, SE0 or suspend; Note 5 1.0 µA ICC(SHARE) Supply current during sharing mode VBUS not connected; Note 5 1.0 µA IDX(SHARE) D+/D- load current during sharing mode 1.0 µA IBUS(SUSP) Suspend mode supply current ICC ICC(STAT) VTH(VBUS) VBUS not connected; ENUMERATE = LOW; Note 5 VBUS supply detection threshold Supply lost 0.8 Supply present VTH(VCC) VCC supply detection threshold V 2.4 V Supply lost (USB_D low) 0.5 Supply present V 1.4 V Digital Pins (VBUS = 4.0V to 5.5V; VCC = 1.8V ± 0.15V) SYMBOL PARAMETER CONDITIONS VIL Logic LOW input voltage VIH Logic HIGH input voltage VOL Logic LOW output voltage IOL = 100µA IOL = 2mA VOH Logic HIGH output voltage IOH = 100µA IOH = 2mA Note 1: Note 2: Note 3: Note 4: Note 5: MIN TYP MAX UNITS 0.5 V 1.2 V 0.15 0.40 1.50 1.25 V V V V Operating Characteristics are over Standard Operating Conditions unless otherwise specified. Equivalent to discharging a 100pF capacitor via a 1.5kΩ resistor (Human body model). Excluding any load current and VPU/VSW source current to 1.5kΩ and 15kΩ pull-up and pull-down resistors (200 µA). Current is drawn from VBUS of Host when device is a peripheral. Low current ideal for battery powered applications. © 2004 California Micro Devices Corp. All rights reserved. 4 430 N. McCarthy Blvd., Milpitas, CA 95035-5112 ● Tel: 408.263.3214 ● Fax: 408.263.7846 ● www.calmicro.com 08/24/04 PRELIMINARY CM2400-02/03/04 Specifications (cont’d) ELECTRICAL OPERATING CHARACTERISTICS (CONT’D) Digital Pins (VBUS = 4.0V to 5.5V; VCC = 2.5V ± 0.2V) SYMBOL PARAMETER CONDITIONS VIL Logic LOW input voltage VIH Logic HIGH input voltage VOL Logic LOW output voltage IOL = 100µA IOL = 2mA VOH Logic HIGH output voltage IOH = 100µA IOH = 2mA MIN TYP MAX UNITS 0.7 V 1.7 V 0.15 0.40 2.15 1.90 V V V V Digital Pins (VBUS = 4.0V to 5.5V; VCC = 1.65V to 3.6V) SYMBOL PARAMETER CONDITIONS VIL Logic LOW input voltage VIH Logic HIGH input voltage VOL Logic LOW output voltage IOL = 100µA IOL = 2mA VOH Logic HIGH output voltage IOH = 100µA IOH = 2mA MIN TYP MAX UNITS 0.3 ∗ VCC V 0.6 ∗ VCC V 0.15 0.40 VCC - 0.15 VCC - 0.40 V V V V Analog I/O Pins (VBUS = 4.0V to 5.5V; VCC = 1.65V to 3.6V) SYMBOL PARAMETER CONDITIONS MIN VDI Differential receiver input sensitivity | VI(D+) - VI(D-) | 0.2 VCM Differential receiver common mode voltage VIL Single-ended receiver logic LOW input voltage VIH Single-ended receiver logic HIGH input voltage 2.0 Single-ended receiver Hysteresis voltage 0.4 VHYS TYP Logic LOW output voltage RL = 1.5KΩ tied to +3.6V VOH Logic HIGH output voltage RL = 15KΩ tied to GND ILZ OFF-state leakage current CIN Transceiver Capacitance RSW Internal switch resistance at VPU ZDRV Driver output impedance (includes 33 ohm 1% resistor) 2.5 V 0.8 V V 2.8 Pin to GND 0.7 V 0.3 V 3.6 V +1 µA 20 pF Ω 50 Measured with steady-state drive; See Note 6 28 UNITS V 0.8 VOL MAX 39 44 Ω Note 6: Rev 2.0 states ZDRV must be between 28Ω and 44Ω, when the driver is not high speed capable. © 2004 California Micro Devices Corp. All rights reserved. 08/24/04 430 N. McCarthy Blvd., Milpitas, CA 95035-5112 ● Tel: 408.263.3214 ● Fax: 408.263.7846 ● www.calmicro.com 5 PRELIMINARY CM2400-02/03/04 Specifications (cont’d) ELECTRICAL OPERATING CHARACTERISTICS (CONT’D) Driver Characteristics & Timings (Full-speed mode only, SPEED=HIGH) SYMBOL PARAMETER CONDITIONS tFR Rise time CL = 50 to 125pF, measured 10% to 90% (VOH-VOL); See Figure 6 tFF Fall time CL = 50 to 125pF, measured 10% to 90% (VOH-VOL); See Figure 6 FRFM Differential rise / fall time matching (tFR / tFF) Excluding the first transition from idle state 100 % VCRS Output signal crossover voltage Excluding the first transition from idle state; See Figure 9 1.65 V tPLH(DRV) Driver propagation delay (VO / VPO ➔ D+ / D- ; FSEO / VMO ➔ D+ / D- LOW-to-HIGH transition; See Figure 9 18 ns HIGH-to-LOW transition; See Figure 9 18 ns Driver disable delay (OE ➔ D+ / D-) HIGH-to-OFF; See Figure 7 15 ns LOW-to-OFF; See Figure 7 15 ns OFF-to-HIGH; See Figure 7 15 ns OFF-to-LOW; See Figure 7 15 ns tPHL(DRV) tPHZ tPLZ tPZH tPZL Driver enable delay (OE ➔ D+ / D-) MIN TYP MAX UNITS 4 20 ns 4 20 ns Driver Characteristics & Timings (Low-speed mode only, SPEED=LOW) SYMBOL PARAMETER CONDITIONS MAX UNITS tLR Rise time CL = 200 to 600pF, measured 10% to 90% (VOH-VOL); See Figure 6 MIN 75 TYP 300 ns tLF Fall time CL = 200 to 600pF, measured 10% to 90% (VOH-VOL); See Figure 6 75 300 ns FRFM Differential rise / fall time matching (tFR / tFF) Excluding the first transition from idle state 80 125 % VCRS Output signal crossover voltage Excluding the first transition from idle state; See Figure 9 1.3 2.0 V MAX UNITS LOW-to-HIGH transition; See Figure 8 15 ns HIGH-to-LOW transition; See Figure 8 15 ns LOW-to-HIGH transition; See Figure 8 18 ns HIGH-to-LOW transition; See Figure 8 18 ns Receiver Timings (Full-speed and low-speed modes) SYMBOL PARAMETER CONDITIONS MIN TYP Differential Receiver tPLH(RCV) tPHL(RCV) Driver propagation delay (D+ / D- ➔ RCV) Single-ended Receiver tPLH(SE) tPHL(SE) Driver propagation delay (D+ / D- ➔ VP / VM) © 2004 California Micro Devices Corp. All rights reserved. 6 430 N. McCarthy Blvd., Milpitas, CA 95035-5112 ● Tel: 408.263.3214 ● Fax: 408.263.7846 ● www.calmicro.com 08/24/04 PRELIMINARY CM2400-02/03/04 Specifications (cont’d) Test Loads Test Point Test Point 15pF 50pF Load for VP / VM and RCV delay measurements 15kΩ 33Ω DUT DUT Load for D+ and D- delay measurements (MAX and MIN Timing) Test Point 33Ω 200Ω DUT V V = VREG(3.3) for tPZL and tPLZ 50pF V = 0 v for tPZH and tPHZ Load for ENABLE and DISABLE delay measurements. © 2004 California Micro Devices Corp. All rights reserved. 08/24/04 430 N. McCarthy Blvd., Milpitas, CA 95035-5112 ● Tel: 408.263.3214 ● Fax: 408.263.7846 ● www.calmicro.com 7 PRELIMINARY CM2400-02/03/04 Performance Information CM2400-02/03/04 Typical DC Characteristics (nominal conditions unless specified otherwise) 300 VBUS CURRENT [µA] VCC CURRENT [µA] 1.00 0.50 0.00 -0.50 250 200 150 100 -1.00 4.1 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 4.3 V CC VOLTAGE [V] 4.7 4.9 5.1 5.3 5.5 V BUS VOLTAGE [V] Figure 1. VCC Current in Idle Mode (SPND=LOW) Figure 3. VBUS Current in Idle Mode (SPND=LOW) 1.00 60.0 VBUS CURRENT [µA] VCC CURRENT [µA] 4.5 0.50 0.00 -0.50 55.0 50.0 45.0 40.0 -1.00 4.1 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 4.3 4.5 4.7 4.9 5.1 5.3 5.5 V BUS VOLTAGE [V] VCC VOLTAGE [V] Figure 4. VBUS Current in Suspend Mode (SPND=HIGH) Figure 2. VCC Current in Suspend Mode (SPND=HIGH) © 2004 California Micro Devices Corp. All rights reserved. 8 430 N. McCarthy Blvd., Milpitas, CA 95035-5112 ● Tel: 408.263.3214 ● Fax: 408.263.7846 ● www.calmicro.com 08/24/04 PRELIMINARY CM2400-02/03/04 Performance Information (cont’d) CM2400-02/03/04 Typical AC Characteristics (nominal conditions unless specified otherwise) D+ D- Figure 5. Rise and Fall Time Matching for Full-Speed Mode D+ D- Figure 6. Rise and Fall Time Matching for Low-Speed Mode © 2004 California Micro Devices Corp. All rights reserved. 08/24/04 430 N. McCarthy Blvd., Milpitas, CA 95035-5112 ● Tel: 408.263.3214 ● Fax: 408.263.7846 ● www.calmicro.com 9 PRELIMINARY CM2400-02/03/04 Performance Information (cont’d) CM2400 Timing Diagrams 3.3V INPUT tFF, tLF tFR, tLR VOH 90% 0V 90% VCRS VCRS tPLH(RCV) tPLH(SE) tPHL(RCV) tPHL(SE) VOH 0.9V 0.9V OUTPUT 10% 10% VOL VOL Figure 7. Rise and Fall Timing Figure 9. D+, D- to RCV, VP and VM Timing 1.65V 1.65V 0.9V INPUT 0.9V INPUT 0V tPHZ tPLZ tPZH tPZL VOH 0.9V tPLH(DRV) tPHL(DRV) 0V -0.3V OUTPUT 0.9V VOH VCRS OUTPUT VCRS VCRS +0.3V VOL VOL Figure 8. OE to D+, D- Timing Figure 10. VO/VPO, FSEO/VMO to D+, D- Timing © 2004 California Micro Devices Corp. All rights reserved. 10 430 N. McCarthy Blvd., Milpitas, CA 95035-5112 ● Tel: 408.263.3214 ● Fax: 408.263.7846 ● www.calmicro.com 08/24/04 PRELIMINARY CM2400-02/03/04 Functional Description The CM2400-02/03/04 USB Transceiver supports 3 different power supply configurations, which can be configured dynamically. Table 1 details the various configurations. In Normal Mode the internal regulator produces 3.3V from VBUS to power the internal drivers and receivers associated with the USB protocol. VBUS VCC CONFIGURATION Connected Connected Normal Mode Connected Not Connected Disable Mode Not Connected Connected Sharing Mode D- lines while in sharing mode. In this mode, VP and VM are driven high while RCV and USB_DET are driven low. In Disable and Sharing Mode, all input/output pins follow the states defined in Table 2. Table 1: Power Supply Connections There are three power supply configurations for the CM2400-02/03/04: Normal mode, Disable mode and Sharing mode. These three modes can be changed dynamically. Normal mode occurs when the VCC and VBUS inputs are both connected to a source. VBUS is tied to a 5V source for 5V operation. The internal regulator of the CM2400-02/03/04 provides 3.3V output on VREG. The VCC input is connected to an independent source that can range from 1.65V to 3.6V. When VCC is not connected and VBUS is connected, the device is in Disable mode. The D+ and D- pins are in tri-state and power consumption drops to a suspend state level. In Sharing mode, VCC is connected while VBUS is below 3.6V. The D+ and D- pins are in tri-state and the CM2400-02/03/04 allows external signals (≤3.6V) to share these two lines. The CM2400-02/03/04 is designed to draw almost zero current from the D+ and PIN Sharing Mode State Disable Mode State VBUS VBUS < 3.6V 4.1V to 5.5V VREG Pulled Down 3.3V Out VCC Present Not Present VPU High-Z (off) High-Z (off) D+, D- High-Z High-Z VP , VM H Invalid RCV L Invalid USB_DET L Invalid Inputs High-Z High-Z Table 2: Pin States in Disable or Sharing Mode Table 3 lists the functions of the modes associated with suspend and OE pins. When Suspend is low and OE is high, signal levels on D+ and D- are determined by other USB devices and pull-up/down resistors. In Suspend Mode (SPND = HIGH) the differential receiver is inactive and output RCV is always LOW. Out of suspend signaling is detected via the single-ended receivers VP and VM. During suspend and while the output is still enabled (OE = LOW), D+ and D- lines are driven to their intended states. SUSPEND OE D+ / D- RCV VP/VM Function L L Driver & Receiver Active Active Active Normal driving mode. Differential receiver active L H Receiving Active Active Driver Tri-stated. Differential receiver active. H L Driving Inactive RCV=L Active Driving during ’suspend’. Differential receiver inactive. H H High-Z Inactive RCV=L Active Low-power state. Table 3: Function Selection. © 2004 California Micro Devices Corp. All rights reserved. 08/24/04 430 N. McCarthy Blvd., Milpitas, CA 95035-5112 ● Tel: 408.263.3214 ● Fax: 408.263.7846 ● www.calmicro.com 11 PRELIMINARY CM2400-02/03/04 Functional Description (cont’d) Detailed in Table 4 and Table 5 are the operating modes for the CM2400-02/03/04. The CM2400-02 features a fixed, single-ended input operating mode which is summarized in Table 4. The CM2400-03 features a differential-pair input operating mode which is summarized in Table 5. The CM2400-04 input mode is selectable via the MODE input. Table 4 and Table 5 summarize both operating modes for the CM2400-04. On the CM2400-02, the two driver inputs function as VO and FSE0 inputs. On the CM2400-03, the driver inputs function as VPO and VMO. On the CM2400-04, when the MODE input is HIGH, differential-pair input mode is selected and the two driver inputs function as VPO and VMO. When MODE is LOW, the single-ended input data interface mode is selected and the two driver inputs function as VO and FSE0. MODE VO (VPO) FSE0 (VMO) Result L (single-ended) L L Logic ‘0’ L H SE0 H L Logic ‘1’ H H SE0 Table 6 details the receiving function when OE is HIGH (driver disabled). RCV denotes the signal level on the output RCV just before an SE0 state occurs. This level is stable during the SE0 period. D+/D- RCV VP VM Differential Logic ’0’ L L H Differential Logic ’1’ H H L SE0 RCV* L L * Denotes RCV is stable in last state before SE0 condition. Table 6: Receiving Function (SPND = L) A regulator bypass option can be utilized by shorting VBUS to VREG and connecting to a 3.3v supply. Table 4: Single-ended Input Operating Mode, CM2400-02 and CM2400-04 in Single-ended Input Mode (OE = L) MODE VO (VPO) FSE0 (VMO) Result H (differential) L L SE0 L H Logic ‘0’ H L Logic ‘1’ H H Undefined Table 5: Differential-pair Input Operating Mode, CM2400-03 and CM2400-04 in Differential-pair Input Mode (OE = L) © 2004 California Micro Devices Corp. All rights reserved. 12 430 N. McCarthy Blvd., Milpitas, CA 95035-5112 ● Tel: 408.263.3214 ● Fax: 408.263.7846 ● www.calmicro.com 08/24/04 PRELIMINARY CM2400-02/03/04 Mechanical Details The CM2400-02/03/04 family is available in a 16-lead HBCC and 16-lead TSSOP packages.The mechanical details for these packages are presented below. Mechanical Package Diagrams HBCC-16 Mechanical Specifications TOP VIEW Dimensions for the CM2400-02HB, CM2400-03HB and CM2400-04HB devices packaged in 16-pin HBCC packages are presented below. D 13 A A1 9 PACKAGE DIMENSIONS E Package HBCC-16 Pins 16 Dimensions Millimeters Inches Min Max A - 0.80 Min 0.0315 Max A1 0.05 0.10 0.0039 b1 0.25 0.35 0.0138 b2 0.30 0.40 0.0157 b3 0.30 0.40 0.0157 D 2.90 3.10 0.1220 e1 Dh 1 Dh 1.45 1.55 0.0610 E 2.90 3.10 0.1220 5 SIDE VIEW BOTTOM VIEW e 13 9 Eh 1.75 1.85 0.0728 e 0.50 TYP. 0.0197 TYP. e1 2.50 TYP. 0.0984 TYP. e2 2.50 TYP. 0.0984 TYP. e3 2.45 TYP. 0.0965 TYP. e4 2.45 TYP 0.0965 TYP. e e4 1/2 e4 5 120 pieces* # per tape and reel 2500 pieces 1 16 Detail C # per tube Eh e2 1/2 e3 Detail A Detail B e3 Controlling dimension: millimeters CONTACT (PIN) DIMENSIONS * This is an approximate number which may vary. CF#0.20x45 ο b3 b2 b1 b1 b2 b3 Detail A Detail B Detail C Dimensions for HBCC-16 Package © 2004 California Micro Devices Corp. All rights reserved. 08/24/04 430 N. McCarthy Blvd., Milpitas, CA 95035-5112 ● Tel: 408.263.3214 ● Fax: 408.263.7846 ● www.calmicro.com 13 PRELIMINARY CM2400-02/03/04 Mechanical Details (cont’d) TSSOP-16 Mechanical Specifications Mechanical Package Diagrams Dimensions for the CM2400-02TS and CM2400-03TS devices packages are presented below. For complete information on the TSSOP-16 package, see the California Micro Devices TSSOP Package Information document. TOP VIEW D 16 15 14 13 12 11 10 9 PACKAGE DIMENSIONS Package TSSOP Pins H 16 Dimensions Millimeters Inches Min Max Min Max A — 1.10 — 0.0433 A1 0.05 0.15 0.002 0.006 B 0.19 0.30 0.0075 0.0118 C 0.09 0.20 0.0035 0.0079 D 4.90 5.10 0.193 0.201 E e E Pin 1 Marking 4.30 4.50 0.169 0.65 BSC 0.177 1 6.25 6.50 0.246 0.256 L 0.50 0.70 0.020 0.028 # per tube Consult Factory # per tape and reel 2500 pcs 3 4 5 6 7 8 SIDE VIEW A A1 SEATING PLANE B 0.0256 BSC H 2 e END VIEW C Controlling dimension: millimeters L Dimensions for the TSSOP-16 Package © 2004 California Micro Devices Corp. All rights reserved. 14 430 N. McCarthy Blvd., Milpitas, CA 95035-5112 ● Tel: 408.263.3214 ● Fax: 408.263.7846 ● www.calmicro.com 08/24/04