PCA EPA1140-450-RC Smd 8 pin 5 tap ttl compatible active delay line Datasheet

SMD 8 Pin 5 Tap TTL Compatible
Active Delay Lines
ELECTRONICS INC.
EPA1140-XX & EPA1140-XX-RC
Add “-RC” after part number for RoHS Compliant
PCA
Part Number
EPA1140-25(-RC)
EPA1140-30(-RC)
EPA1140-35(-RC)
EPA1140-40(-RC)
EPA1140-45(-RC)
EPA1140-50(-RC)
EPA1140-60(-RC)
EPA1140-75(-RC)
EPA1140-100(-RC)
EPA1140-125(-RC)
Total Delay
(†±5% or ± 2nS)
Tap Delays
(†±5% or ± 2nS)
5, 10, 15, 20
6, 12, 18, 24
7, 14, 21, 28
8, 16, 24, 32
9, 18, 27, 36
10, 20, 30, 40
12, 24, 36, 48
15, 30, 45, 60
20, 40, 60, 80
25, 50, 75, 100
PCA
Part Number
EPA1140-150(-RC)
EPA1140-175(-RC)
EPA1140-200(-RC)
EPA1140-225(-RC)
EPA1140-250(-RC)
EPA1140-300(-RC)
EPA1140-350(-RC)
EPA1140-400(-RC)
EPA1140-450(-RC)
EPA1140-500(-RC)
25
30
35
40
45
50
60
75
100
125
Tap Delays
(†±5% or ± 2nS)
Total Delay
(†±5% or ± 2nS)
30, 60, 90, 120
35, 70, 105, 140
40, 80, 120, 160
45, 90, 135, 180
50, 100, 150, 200
60, 120, 180, 240
70, 140, 210, 280
80, 160, 240, 320
90, 180, 270, 360
100, 200, 300, 400
150
175
200
225
250
300
350
400
450
500
†Whichever is greater. Delay times referenced from input to leading and trailing edges at 25°C, 5.0V, with no load.
DC Electrical Characteristics
Parameter
VOH
VOL
VIK
IIH
Test Conditions
Min.
V CC = min. V IL = max. I OH = max 2.7
V CC = min. V IH = min. I OL = max
V CC = min. II = II K
V CC = max. VIN = 2.7V
V CC = max. VIN = 5.25V
IIL
Low-Level Input Current
V CC = max. VIN = 0.5V
IOS
Short Circuit Output Current V CC = max. V OUT = 0.
-40
(One output at a time)
ICCH High-Level Supply Current
V CC = max. VIN = OPEN
ICCL Low-Level Supply Current
V CC = max. VIN = 0
TRO Output Rise Time
Td ≤ 500 nS (0.75 to 2.4 Volts)
NH
Fanout High-Level Output
V CC = max. V OH = 2.7V
NL
Fanout Low-Level Output
V CC = max. V OL = 0.5V
Max.
Unit
0.5
-1.2
50
1.0
-2
-100
V
V
V
µA
mA
mA
mA
High-Level Output Voltage
Low-Level Output Voltage
Input Clamp Voltage
High-Level Input Current
Schematic
8
VCC
7
2
6
Recommended Operating Conditions Min.
Supply Voltage
High-Level Input Voltage
Low-Level Input Voltage
Input Clamp Current
High-Level Output Current
Low-Level Output Current
Pulse Width of Total Delay
Duty Cycle
Operating Free-Air Temperature
4.75
2.0
Max.
Unit
5.25
V
V
V
mA
mA
mA
%
%
°C
0.8
-18
-1.0
20
40
-55
40
+125
5 OUTPUT
INPUT 1
4 GROUND
75
mA
75
mA
4
nS
20 TTL Load
10 TTL Load
Package
.030
(.762)
PCA
.400
.280
Max. EPA1140-25(-RC) Max.
(10.16)
(7.11)
D.C.
VCC
VIH
VIL
IIK
IOH
IOL
PW*
d*
TA
3
.055
(1.40)
.100
(2.54)
Pad Layout
.410
(10.41)
.100
(2.54)
.500 Max.
.010
Typ.
(.254)
.250
Max.
(6.35)
.020
(.508)
.050
(1.27)
.300
(7.62)
*These two values are inter-dependent.
Notes :
Input Pulse Test Conditions @ 25° C
EIN
PW
TRI
PRR
Pulse Input Voltage
Pulse Width % of Total Delay
Pulse Rise Time (0.75 - 2.4 Volts)
Pulse Repetition Rate @ Td ≤ 200 nS
Pulse Repetition Rate @ Td > 200 nS
VCC Supply Voltage
Unit
3.2
110
2.0
1.0
100
5.0
Volts
%
nS
MHz
KHz
Volts
EPA1140-XX
EPA1140-XX-RC
1. Lead Finish
SnPb
Hot Tin Dip (Sn) †
2. Peak Temperature Rating
225°C
260°C
4. Weight
.976 grams
.976 grams
(Tube) TBD pieces/tube
5. Packaging Information
(*Add “TR” to end of part
(Tape & Reel) TBD pieces/13” reel
number, but in front of
(*EPA1140-XXTR)
“-RC”when placing order)
TBD pieces/tube
TBD pieces/13” reel
(*EPA1140-XXTR-RC)
† Lead Material : Matte Tin with Ni Barrier
Unless Otherwise Specified Dimensions are in Inches /mm ± .010 /.25
PCA ELECTRONICS, INC.
16799 SCHOENBORN ST.
NORTH HILLS, CA 91343
Product performance is limited to specified parameters. Data is subject to change without prior notice.
CSA1140-XX & -RC
Rev. B
8/17/06 RR
TEL: (818) 892-0761
FAX: (818) 894-5791
http://www.pca.com
Similar pages