Juxing ES5C Surface mount superfast rectifier Datasheet

ES5A-ES5J
Surface Mount Superfast Rectifiers
Features
• Super fast switching time for high efficiency
• Low forward voltage drop and
high current capability
• Low reverse leakage current
• Plastic material has UL flammability
classification 94V-0
SMC ( DO-214AB )
.128(3.25)
.108(2.75)
Mechanical Data
•
•
•
•
Case: DO-214AB (SMC) molded plastic body
Epoxy: UL 94V-0 rate flame retardant
Lead: Lead formed for surface mount
Mounting Position: Any
Dimensions in inches and (millimeters)
Maximum Ratings and Electrical Characteristics
o
Rating at 25 C
ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or
inductive load. For capacitive load, derate current by 20%
Type Number
Maximum Recurrent Peak Reverse Voltage
Maximum RMS Voltage
Maximum DC Blocking Voltage
Maximum Average Forward Rectified Current
See Fig. 1
Peak Forward Surge Current, 8.3 ms Single
Half Sine-wave Superimposed on Rated
Load (JEDEC method ) @TL = 100 oC
Maximum Instantaneous Forward
Voltage @ 5.0A
Maximum DC Reverse Current @ TA =25 oC
at Rated DC Blocking Voltage @ TA=100 oC
Maximum Reverse Recovery Time ( Note 1 )
Typical Junction Capacitance ( Note 2 )
Typical Thermal Resistance (Note 3)
Operating Temperature Range
Storage Temperature Range
Notes:
Symbol
ES
5A
ES
5B
ES
5C
ES
5D
ES
5F
ES
5G
VRRM
VRMS
VDC
50
35
50
100 150 200 300 400 500 600
70 105 140 210 280 350 420
100 150 200 300 400 500 600
ES
5J
Units
V
V
V
I(AV)
5.0
A
IFSM
150
A
VF
0.95
TJ
1.7
V
10
500
35
IR
Trr
Cj
RθJA
RθJL
1.3
45
uA
uA
nS
pF
30
47
12
-55 to +150
-55 to +150
TSTG
1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A
2. Measured at 1 MHz and Applied VR=4.0 Volts
3. Units Mounted on P.C.B. with 0.6” x 0.6”(16mm x 16mm) Copper Pad Areas
http://www.trr-jx.com
ES
5H
o
C /W
o
o
C
C
ES5A-ES5J
Surface Mount Superfast Rectifiers
FIG.1- MAXIMUM FORWARD CURRENT DERATING
CURVE
6
RESISTIVE OR
INDUCTIVE LOAD
100
2
P.C.B. MOUNTED ON
0.6X0.6"(16X16mm) COPPER PADS
80
90
100
110
120
130
o
LEAD TEMPERATURE. ( C)
140
75
50
25
0
150
100
10
1
NUMBER OF CYCLES AT 60Hz
FIG.3- TYPICAL INSTANTANEOUS
FORWARD CHARACTERISTICS
100
8.3ms Single Half Sine Wave
o
(JEDEC Method) at TL=120 C
125
4
0
FIG.2- MAXIMUM NON-REPETITIVE PEAK FORWARD
SURGE CURRENT
150
PEAK FORWARD SURGE
CURRENT. (A)
AVERAGE FORWARD CURRENT. (A)
Characteristic Curves (TA=25 ℃ unless otherwise noted)
FIG.4- TYPICAL REVERSE CHARACTERISTICS
1000
-G
ES
5A
-D
10
INSTANTANEOUS REVERSE CURRENT. ( A)
INSTANTANEOUS FORWARD CURRENT. (A)
0
Tj=25 C
PULSE WIDTH-300 S
1% DUTY CYCLE
ES
5F
1
ES
5H
-J
0.1
0.01
0.4
0.8
1.0
1.2
1.4
FORWARD VOLTAGE. (V)
1.6
JUNCTION CAPACITANCE.(pF)
Tj=25 C
f=1.0MHz
Vsig=50mVp-p
90
75
60
45
ES5
F-J
A-
D
15
0
1
Tj=75 0C
1
Tj=25 0C
0.1
100
0
ES5
10
20
40
60
80
100
120
10
REVERSE VOLTAGE. (V)
100
FIG.6- TYPICAL TRANSIENT THERMAL IMPEDANCE
10
1
0.1
0.01
0.1
1
T, HEATING TIME (sec.)
FIG.7- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM
50W
NONINDUCTIVE
10W
NONINDUCTIVE
trr
+0.5A
(+)
50Vdc
(approx)
(-)
(-)
DUT
PULSE
GENERATOR
(NOTE 2)
1W
NON
INDUCTIVE
OSCILLOSCOPE
(NOTE 1)
NOTES: 1. Rise Time=7ns max. Input Impedance=
1 megohm 22pf
2. Rise Time=10ns max. Sourse Impedance=
50 ohms
http://www.trr-jx.com
140
PERCENT OF RATED PEAK REVERSE VOLTAGE. (%)
FIG.5- TYPICAL JUNCTION CAPACITANCE
30
Tj=100 0C
0.01
0
1.8
TRANSIENT THERMAL IMPEDANCE ( OC/W)
105
0.6
100
0
-0.25A
(+)
-1.0A
1cm
SET TIME BASE FOR
5/ 10ns/ cm
10
100
Similar pages