EPCOS B41044A3337M016 Aluminum electrolytic capacitor Datasheet

AEC-C_B41044_B43044.book Seite 1 Dienstag, 5. August 2008 4:13 16
Aluminum electrolytic capacitors
Alu-X product lines
Single-ended capacitors
Series/Type:
Data
Sheet
Date:
B41044, B43044
August 2008
© EPCOS AG 2008. Reproduction, publication and dissemination of this publication and the information contained therein without EPCOS’ prior express consent is prohibited.
AEC-C_B41044_B43044.book Seite 2 Dienstag, 5. August 2008 4:13 16
Single-ended capacitors
Very low impedance – 105 °C
Single-ended capacitors
Very low impedance – 105 °C
B41044, B43044
B41044, B43044
Long-life grade capacitors for professional applications
Applications
■ Professional switch mode power supplies
Features
■
■
■
■
■
RoHS-compatible
High C/V value
Very low impedance at high frequencies
High reliability
Load life of 5000 h at 105 °C
Construction
■
■
■
■
■
Radial leads
Aluminum case, fully insulated
Charge-discharge proof
Minus pole marking on the insulating sleeve
Case with safety vent from diameter 8 mm
Delivery mode
■
■
■
■
Bulk
Taped, Ammo pack
Cut
Kinked
Please read Cautions and warnings and
Important notes at the end of this document.
2
08/08
AEC-C_B41044_B43044.book Seite 3 Dienstag, 5. August 2008 4:13 16
Single-ended capacitors
Very low impedance – 105 °C
B41044, B43044
Specifications and characteristics in brief
Rated voltage VR
Operating temperature range
Rated capacitance CR
(20 °C, 120 Hz)
Capacitance tolerance
Load life
(105 °C, VR, IAC,R)
Leakage current Ileak
6.3 … 450 V DC
VR < 350 V DC: –40 °C … +105 °C
VR ≥ 350 V DC: –25 °C … +105 °C
0.22 … 15000 µF
±20% M
VR ≤ 100 V DC
2000 h for d = 5 ... 6.3 mm
3000 h for d = 8 mm
5000 h for d ≥ 10 mm
Low temperature
stability
(impedance ratio)
(120 Hz)
Shelf life
Requirements:
∆C/C ≤ ±20% of
initial value
tan δ ≤ 2 times initial
specified value
Ileak ≤ initial
specified limit
VR > 100 V DC
VR ≤ 100 V DC
leak
Dissipation factor
(max.)
(20 °C, 120 Hz)
VR > 100 V DC
2000 h
CR VR
≤ 0.03 µA ⋅ ⎛ ------- ⋅ -------⎞ or 4 µA
⎝ µF V ⎠
whichever is greater
(20 °C, after 1 minute)
VR
6.3
10
16
(V DC)
CR VR
I leak ≤ 0.02 µA ⋅ ⎛ ------- ⋅ -------⎞ +15 µA
⎝ µF V ⎠
(20 °C, after 5 minutes)
160 350
…
…
315 450
tan δ
0.22 0.19 0.16 0.14 0.12 0.10 0.09 0.08 0.15 0.20
For capacitance higher than 1000 µF add 0.02 for every increase of
1000 µF.
VR (V DC)
6.3
10
16
25 ... 100 160 ... 250 315 ... 450
4
3
2
2
3
8
Z ( – 25 °C )
--------------------------Z ( +20 °C )
25
35
50
63
100
8
6
4
3
4
–
Z ( – 40 °C )
--------------------------Z ( +20 °C )
After storage for 1000 h at 105 °C, the capacitors shall meet the
requirement of load life test after reforming process. After test: VR to be
applied for 30 minutes, 24 to 48 hours before measurement.
Please read Cautions and warnings and
Important notes at the end of this document.
3
08/08
AEC-C_B41044_B43044.book Seite 4 Dienstag, 5. August 2008 4:13 16
Single-ended capacitors
Very low impedance – 105 °C
B41044, B43044
Specifications and characteristics in brief
Frequency multiplier Voltage range
for rated ripple current 6.3 ... 100 V DC
50 ... 60 Hz
0.47 … 10 µF
–
22 … 33 µF
–
47 … 330 µF
–
470 … 1000 µF –
2200 ... 15000 µF –
Voltage range
0.40
160 ... 450 V DC
Temperature multiplier
+70 °C
for rated ripple current 6.3 ... 100 V DC 2.0
160 ... 450 V DC 1.8
Please read Cautions and warnings and
Important notes at the end of this document.
4
120 Hz
0.42
0.55
0.70
0.75
0.80
0.50
08/08
Frequency
1 kHz
0.60
0.75
0.85
0.90
0.95
0.75
+85 °C
1.7
1.4
10 kHz
0.80
0.90
0.95
0.98
1.00
0.90
100 kHz
1.00
1.00
1.00
1.00
1.00
1.00
+105 °C
1.0
1.0
AEC-C_B41044_B43044.book Seite 5 Dienstag, 5. August 2008 4:13 16
Single-ended capacitors
Very low impedance – 105 °C
B41044, B43044
Dimensional drawing
l
+
øb
d
a
15 min.
Minus pole
marking
5 min.
Safety vent
KAL1080-C-E
Safety vent for diameter ≥ 8 mm.
Case dimensions
d×l
mm
dmax × Imax
mm
a
mm
b
mm
× 11
5.5 × 12.5
2.0 ±0.5
0.5 ±0.1
6.3 × 11
6.8 × 12.5
2.5 ±0.5
0.5 ±0.1
5
8
× 11.5
8.5 × 13.0
3.5 ±0.5
0.6 ±0.1
8
× 15
8.5 × 16.5
3.5 ±0.5
0.6 ±0.1
8
× 20
8.5 × 21.5
3.5 ±0.5
0.6 ±0.1
10
× 12.5
11.0 × 14.0
5.0 ±0.5
0.6 ±0.1
10
× 16
11.0 × 17.5
5.0 ±0.5
0.6 ±0.1
10
× 20
11.0 × 22.0
5.0 ±0.5
0.6 ±0.1
12.5 × 20
13.5 × 22.0
5.0 ±0.5
0.6 ±0.1
12.5 × 25
13.5 × 27.0
5.0 ±0.5
0.6 ±0.1
16
× 20
17.0 × 22.0
7.5 ±0.5
0.8 ±0.1
16
× 25
17.0 × 27.0
7.5 ±0.5
0.8 ±0.1
16
× 31.5
17.0 × 33.5
7.5 ±0.5
0.8 ±0.1
16
× 35.5
17.0 × 37.5
7.5 ±0.5
0.8 ±0.1
18
× 20
19.0 × 22.0
7.5 ±0.5
0.8 ±0.1
18
× 25
19.0 × 27.0
7.5 ±0.5
0.8 ±0.1
18
× 31.5
19.0 × 33.5
7.5 ±0.5
0.8 ±0.1
18
× 35.5
19.0 × 37.5
7.5 ±0.5
0.8 ±0.1
18
× 40
19.0 × 42.0
7.5 ±0.5
0.8 ±0.1
Please read Cautions and warnings and
Important notes at the end of this document.
5
08/08
AEC-C_B41044_B43044.book Seite 6 Dienstag, 5. August 2008 4:13 16
Single-ended capacitors
Very low impedance – 105 °C
B41044, B43044
Overview of available types B41044
VR (V DC)
6.3
10
16
25
Case dimensions d × l (mm)
CR (µF)
4.7
5
10
22
5
× 11
5
× 11
× 11
5
× 11
5
× 11
5
× 11
5
× 11
33
5
× 11
5
× 11
5
× 11
5
× 11
47
5
× 11
5
× 11
5
× 11
5
× 11
× 11
5
100
5
× 11
6.3 × 11
150
6.3 × 11
6.3 × 11
6.3 × 11
6.3 × 11
8
× 11.5
220
6.3 × 11
6.3 × 11
8
× 11.5
8
× 11.5
330
6.3 × 11
8
× 11.5
8
× 11.5
10
× 12.5
470
8
× 11.5
8
× 11.5
10
× 12.5
10
× 16
680
10
× 12.5
10
× 12.5
10
× 16
10
× 20
1000
10
× 12.5
10
× 16
10
× 20
12.5 × 20
1500
10
× 20
10
× 20
12.5 × 20
16
× 20
2200
12.5 × 20
12.5 × 20
12.5 × 25
16
× 25
3300
12.5 × 20
12.5 × 25
16
× 25
16
× 31.5
4700
16
× 25
16
× 25
16
× 31.5
18
× 35.5
6800
16
× 25
16
× 31.5
18
× 35.5
10000
16
× 31.5
16
× 35.5
15000
16
× 35.5
Please read Cautions and warnings and
Important notes at the end of this document.
6
08/08
AEC-C_B41044_B43044.book Seite 7 Dienstag, 5. August 2008 4:13 16
Single-ended capacitors
Very low impedance – 105 °C
B41044, B43044
Overview of available types B41044
VR (V DC)
35
50
63
100
Case dimensions d × l (mm)
CR (µF)
× 11
0.22
5
0.47
5
× 11
1.0
5
× 11
2.2
5
× 11
5
× 11
3.3
5
× 11
5
× 11
5
× 11
× 11
5
× 11
5
× 11
5
× 11
5
10
5
× 11
5
× 11
5
× 11
6.3 × 11
22
5
× 11
5
× 11
6.3 × 11
8
× 11.5
33
5
× 11
6.3 × 11
6.3 × 11
10
× 12.5
47
6.3 × 11
× 11.5
10
× 16
12.5 × 20
4.7
8
× 11.5
8
10
× 16
8
× 11.5
8
× 11.5
150
8
× 11.5
10
× 12.5
10
× 20
12.5 × 25
220
10
× 12.5
10
× 16
10
× 25
16
× 25
330
10
× 16
10
× 20
12.5 × 20
16
× 31.5
470
10
× 20
12.5 × 20
16
× 20
18
× 40
680
12.5 × 20
12.5 × 25
16
× 25
1000
12.5 × 25
16
× 25
16
× 35.5
1500
16
× 25
16
× 31.5
2200
16
× 31.5
18
× 35.5
3300
18
× 35.5
100
Please read Cautions and warnings and
Important notes at the end of this document.
7
08/08
AEC-C_B41044_B43044.book Seite 8 Dienstag, 5. August 2008 4:13 16
Single-ended capacitors
Very low impedance – 105 °C
B41044, B43044
Overview of available types B43044
VR (V DC)
160
200
250
Case dimensions d × l (mm)
CR (µF)
10
10
× 20
22
10
× 20
10
× 20
12.5 × 20
33
10
× 20
12.5 × 20
12.5 × 25
47
12.5 × 20
12.5 × 20
12.5 × 25
68
12.5 × 20
12.5 × 25
16
× 25
100
16
× 25
16
× 25
16
× 31.5
150
16
× 31.5
18
× 25
18
× 31.5
220
16
× 31.5
18
× 31.5
18
× 40
330
18
× 31.5
VR (V DC)
350
400
450
Case dimensions d × l (mm)
CR (µF)
× 20
3.3
10
4.7
12.5 × 20
× 20
10
10
22
12.5 × 20
33
16
× 20
47
16
68
100
10
× 20
12.5 × 25
12.5 × 25
16
× 25
16
× 25
16
× 31.5
× 25
16
× 25
18
× 31.5
16
× 31.5
18
× 31.5
18
× 35.5
18
× 31.5
18
× 40
8
08/08
Please read Cautions and warnings and
Important notes at the end of this document.
AEC-C_B41044_B43044.book Seite 9 Dienstag, 5. August 2008 4:13 16
Single-ended capacitors
Very low impedance – 105 °C
B41044, B43044
Technical data and ordering codes B41044
VR
V DC
6.3
10
CR
120 Hz
20 °C
µF
Case
dimensions
d×l
mm
Zmax
100 kHz
20 °C
Ω
IAC,R
100 kHz
105 °C
mA
Ordering code
(composition see
below)
22
33
47
100
150
220
330
470
680
1000
1500
2200
3300
4700
6800
10000
15000
5
5
5
5
6.3
6.3
6.3
8
10
10
10
12.5
12.5
16
16
16
16
× 11
× 11
× 11
× 11
× 11
× 11
× 11
× 11.5
× 12.5
× 12.5
× 20
× 20
× 20
× 25
× 25
× 31.5
× 35.5
0.700
0.700
0.650
0.650
0.300
0.300
0.300
0.140
0.100
0.100
0.054
0.050
0.050
0.030
0.030
0.025
0.022
180
180
180
180
280
280
280
450
660
660
1100
1400
1400
2100
2100
2600
3000
B41044A2226M***
B41044A2336M***
B41044A2476M***
B41044A2107M***
B41044A2157M***
B41044A2227M***
B41044A2337M***
B41044A2477M***
B41044A2687M***
B41044A2108M***
B41044A2158M***
B41044A2228M***
B41044A2338M***
B41044A2478M***
B41044A2688M***
B41044A2109M***
B41044A2159M***
22
33
47
100
150
220
330
470
680
1000
1500
2200
3300
4700
6800
10000
5
5
5
5
6.3
6.3
8
8
10
10
10
12.5
12.5
16
16
16
× 11
× 11
× 11
× 11
× 11
× 11
× 11.5
× 11.5
× 12.5
× 16
× 20
× 20
× 25
× 25
× 31.5
× 35.5
0.700
0.700
0.650
0.650
0.300
0.300
0.140
0.140
0.100
0.080
0.054
0.050
0.038
0.030
0.025
0.022
180
180
180
180
280
280
450
450
660
850
1100
1400
1700
2100
2600
3000
B41044A3226M***
B41044A3336M***
B41044A3476M***
B41044A3107M***
B41044A3157M***
B41044A3227M***
B41044A3337M***
B41044A3477M***
B41044A3687M***
B41044A3108M***
B41044A3158M***
B41044A3228M***
B41044A3338M***
B41044A3478M***
B41044A3688M***
B41044A3109M***
*** = Version
000 = for
001 = for
002 = for
016 = for
007 = for
006 = for
008 = for
standard leads, bulk
kinked leads, bulk
cut leads, bulk
taped leads, Ammo pack,
taped leads, Ammo pack,
taped leads, Ammo pack,
taped leads, Ammo pack,
lead
lead
lead
lead
Please read Cautions and warnings and
Important notes at the end of this document.
spacing
spacing
spacing
spacing
a
a
a
a
=
=
=
=
9
2.0
2.5
3.5
5.0
mm
mm
mm
mm
08/08
AEC-C_B41044_B43044.book Seite 10 Dienstag, 5. August 2008 4:13 16
Single-ended capacitors
Very low impedance – 105 °C
B41044, B43044
Technical data and ordering codes B41044
VR
V DC
CR
120 Hz
20 °C
µF
Case
dimensions
d×l
mm
Zmax
100 kHz
20 °C
Ω
IAC,R
100 kHz
105 °C
mA
Ordering code
(composition see
below)
16
10
22
33
47
100
150
220
330
470
680
1000
1500
2200
3300
4700
6800
5
5
5
5
6.3
6.3
8
8
10
10
10
12.5
12.5
16
16
18
× 11
× 11
× 11
× 11
× 11
× 11
× 11.5
× 11.5
× 12.5
× 16
× 20
× 20
× 25
× 25
× 31.5
× 35.5
0.70
0.70
0.70
0.65
0.30
0.30
0.14
0.14
0.10
0.080
0.054
0.050
0.038
0.030
0.025
0.022
180
180
180
180
280
280
450
450
660
850
1100
1400
1700
2100
2600
3000
B41044A4106M***
B41044A4226M***
B41044A4336M***
B41044A4476M***
B41044A4107M***
B41044A4157M***
B41044A4227M***
B41044A4337M***
B41044A4477M***
B41044A4687M***
B41044A4108M***
B41044A4158M***
B41044A4228M***
B41044A4338M***
B41044A4478M***
B41044A4688M***
25
4.7
10
22
33
47
100
150
220
330
470
680
1000
1500
2200
3300
4700
5
5
5
5
5
6.3
8
8
10
10
10
12.5
16
16
16
18
× 11
× 11
× 11
× 11
× 11
× 11
× 11.5
× 11.5
× 12.5
× 16
× 20
× 20
× 20
× 25
× 31.5
× 35.5
0.70
0.70
0.70
0.70
0.65
0.30
0.14
0.14
0.10
0.080
0.054
0.050
0.030
0.030
0.025
0.022
180
180
180
180
180
280
450
450
660
850
1100
1400
2100
2100
2600
3000
B41044A5475M***
B41044A5106M***
B41044A5226M***
B41044A5336M***
B41044A5476M***
B41044A5107M***
B41044A5157M***
B41044A5227M***
B41044A5337M***
B41044A5477M***
B41044A5687M***
B41044A5108M***
B41044A5158M***
B41044A5228M***
B41044A5338M***
B41044A5478M***
*** =Version
000 =
001 =
002 =
016 =
007 =
006 =
008 =
for
for
for
for
for
for
for
standard leads, bulk
kinked leads, bulk
cut leads, bulk
taped leads, Ammo pack,
taped leads, Ammo pack,
taped leads, Ammo pack,
taped leads, Ammo pack,
lead
lead
lead
lead
Please read Cautions and warnings and
Important notes at the end of this document.
spacing
spacing
spacing
spacing
a
a
a
a
=
=
=
=
10
2.0
2.5
3.5
5.0
mm
mm
mm
mm
08/08
AEC-C_B41044_B43044.book Seite 11 Dienstag, 5. August 2008 4:13 16
Single-ended capacitors
Very low impedance – 105 °C
B41044, B43044
Technical data and ordering codes B41044
VR
V DC
CR
120 Hz
20 °C
µF
Case
dimensions
d×l
mm
Zmax
100 kHz
20 °C
Ω
IAC,R
100 kHz
105 °C
mA
Ordering code
(composition see
below)
35
4.7
10
22
33
47
100
150
220
330
470
680
1000
1500
2200
3300
5
5
5
5
6.3
8
8
10
10
10
12.5
12.5
16
16
18
× 11
× 11
× 11
× 11
× 11
× 11.5
× 11.5
× 12.5
× 16
× 20
× 20
× 25
× 25
× 31.5
× 35.5
0.70
0.70
0.70
0.65
0.30
0.14
0.14
0.10
0.080
0.054
0.050
0.038
0.030
0.025
0.022
180
180
180
180
280
450
450
660
850
1100
1400
1700
2100
2600
3000
B41044A7475M***
B41044A7106M***
B41044A7226M***
B41044A7336M***
B41044A7476M***
B41044A7107M***
B41044A7157M***
B41044A7227M***
B41044A7337M***
B41044A7477M***
B41044A7687M***
B41044A7108M***
B41044A7158M***
B41044A7228M***
B41044A7338M***
50
0.22
0.47
1.0
2.2
3.3
4.7
10
22
33
47
100
150
220
330
470
680
1000
1500
2200
5
5
5
5
5
5
5
5
6.3
8
8
10
10
10
12.5
12.5
16
16
18
× 11
× 11
× 11
× 11
× 11
× 11
× 11
× 11
× 11
× 11.5
× 11.5
× 12.5
× 16
× 20
× 20
× 25
× 25
× 31.5
× 35.5
8.0
5.0
3.5
3.0
2.6
2.3
1.4
1.2
0.60
0.43
0.35
0.17
0.20
0.10
0.085
0.065
0.043
0.038
0.034
18
25
40
55
65
90
120
150
200
250
340
490
650
810
1100
1200
1600
2000
2300
B41044A6224M***
B41044A6474M***
B41044A6105M***
B41044A6225M***
B41044A6335M***
B41044A6475M***
B41044A6106M***
B41044A6226M***
B41044A6336M***
B41044A6476M***
B41044A6107M***
B41044A6157M***
B41044A6227M***
B41044A6337M***
B41044A6477M***
B41044A6687M***
B41044A6108M***
B41044A6158M***
B41044A6228M***
*** = Version
000 = for
001 = for
002 = for
016 = for
007 = for
006 = for
008 = for
standard leads, bulk
kinked leads, bulk
cut leads, bulk
taped leads, Ammo pack,
taped leads, Ammo pack,
taped leads, Ammo pack,
taped leads, Ammo pack,
lead
lead
lead
lead
Please read Cautions and warnings and
Important notes at the end of this document.
spacing
spacing
spacing
spacing
a
a
a
a
=
=
=
=
11
2.0
2.5
3.5
5.0
mm
mm
mm
mm
08/08
AEC-C_B41044_B43044.book Seite 12 Dienstag, 5. August 2008 4:13 16
Single-ended capacitors
Very low impedance – 105 °C
B41044, B43044
Technical data and ordering codes B41044
VR
V DC
CR
120 Hz
20 °C
µF
Case
dimensions
d×l
mm
Zmax
100 kHz
20 °C
Ω
IAC,R
100 kHz
105 °C
mA
Ordering code
(composition see
below)
63
3.3
4.7
10
22
33
47
100
150
220
330
470
680
1000
5
5
5
6.3
6.3
8
10
10
10
12.5
16
16
16
× 11
× 11
× 11
× 11
× 11
× 11.5
× 16
× 20
× 25
× 20
× 20
× 25
× 35.5
2.0
2.0
2.0
0.60
0.60
0.50
0.12
0.10
0.090
0.085
0.050
0.043
0.025
64
76
111
190
233
328
456
610
809
1036
1411
1843
1967
B41044A8335M***
B41044A8475M***
B41044A8106M***
B41044A8226M***
B41044A8336M***
B41044A8476M***
B41044A8107M***
B41044A8157M***
B41044A8227M***
B41044A8337M***
B41044A8477M***
B41044A8687M***
B41044A8108M***
100
2.2
3.3
4.7
10
22
33
47
100
150
220
330
470
5
5
5
6.3
8
10
10
12.5
12.5
16
16
18
× 11
× 11
× 11
× 11
× 11.5
× 12.5
× 16
× 20
× 25
× 25
× 31.5
× 40
2.5
2.5
2.5
1.0
0.60
0.40
0.30
0.15
0.12
0.070
0.050
0.030
52
64
76
128
224
319
417
570
762
1048
1404
1980
B41044A9225M***
B41044A9335M***
B41044A9475M***
B41044A9106M***
B41044A9226M***
B41044A9336M***
B41044A9476M***
B41044A9107M***
B41044A9157M***
B41044A9227M***
B41044A9337M***
B41044A9477M***
*** = Version
000 = for
001 = for
002 = for
016 = for
007 = for
006 = for
008 = for
standard leads, bulk
kinked leads, bulk
cut leads, bulk
taped leads, Ammo pack,
taped leads, Ammo pack,
taped leads, Ammo pack,
taped leads, Ammo pack,
lead
lead
lead
lead
Please read Cautions and warnings and
Important notes at the end of this document.
spacing
spacing
spacing
spacing
a
a
a
a
=
=
=
=
12
2.0
2.5
3.5
5.0
mm
mm
mm
mm
08/08
AEC-C_B41044_B43044.book Seite 13 Dienstag, 5. August 2008 4:13 16
Single-ended capacitors
Very low impedance – 105 °C
B41044, B43044
Technical data and ordering codes B43044
VR
V DC
CR
120 Hz
20 °C
µF
Case
dimensions
d×l
mm
Zmax
100 kHz
20 °C
Ω
IAC,R
100 kHz
105 °C
mA
Ordering code
(composition see
below)
160
22
33
47
68
100
150
220
330
10
10
12.5
12.5
16
16
16
18
× 20
× 20
× 20
× 20
× 25
× 31.5
× 31.5
× 31.5
1.3
1.3
0.91
0.63
0.27
0.22
0.22
0.22
440
565
725
950
1280
1300
1300
1700
B43044A1226M***
B43044A1336M***
B43044A1476M***
B43044A1686M***
B43044A1107M***
B43044A1157M***
B43044A1227M***
B43044A1337M***
200
22
33
47
68
100
150
220
10
12.5
12.5
12.5
16
18
18
× 20
× 20
× 20
× 25
× 25
× 25
× 31.5
1.5
0.91
0.91
0.63
0.27
0.27
0.22
440
590
780
950
1280
1500
1700
B43044A2226M***
B43044A2336M***
B43044A2476M***
B43044A2686M***
B43044A2107M***
B43044A2157M***
B43044A2227M***
250
10
22
33
47
68
100
150
220
10
12.5
12.5
12.5
16
16
18
18
× 20
× 20
× 25
× 25
× 25
× 31.5
× 31.5
× 40
3.5
2.3
1.7
1.7
0.78
0.63
0.42
0.35
300
480
630
630
1000
1400
1450
1485
B43044F2106M***
B43044F2226M***
B43044F2336M***
B43044F2476M***
B43044F2686M***
B43044F2107M***
B43044F2157M***
B43044F2227M***
350
10
22
33
47
68
100
10
12.5
16
16
16
18
× 20
× 20
× 20
× 25
× 31.5
× 31.5
2.9
2.1
0.91
0.73
0.49
0.40
180
270
600
700
1100
1170
B43044A4106M***
B43044A4226M***
B43044A4336M***
B43044A4476M***
B43044A4686M***
B43044A4107M***
*** = Version
000 = for
001 = for
002 = for
016 = for
007 = for
006 = for
008 = for
standard leads, bulk
kinked leads, bulk
cut leads, bulk
taped leads, Ammo pack,
taped leads, Ammo pack,
taped leads, Ammo pack,
taped leads, Ammo pack,
lead
lead
lead
lead
Please read Cautions and warnings and
Important notes at the end of this document.
spacing
spacing
spacing
spacing
a
a
a
a
=
=
=
=
13
2.0
2.5
3.5
5.0
mm
mm
mm
mm
08/08
AEC-C_B41044_B43044.book Seite 14 Dienstag, 5. August 2008 4:13 16
Single-ended capacitors
Very low impedance – 105 °C
B41044, B43044
Technical data and ordering codes B43044
VR
V DC
CR
120 Hz
20 °C
µF
400
450
*** = Version
000 = for
001 = for
002 = for
016 = for
007 = for
006 = for
008 = for
10
22
33
47
68
100
3.3
4.7
10
22
33
47
68
Case
dimensions
d×l
mm
Zmax
100 kHz
20 °C
Ω
IAC,R
100 kHz
105 °C
mA
Ordering code
(composition see
below)
10
12.5
16
16
18
18
× 20
× 25
× 25
× 25
× 31.5
× 40
2.9
1.3
0.91
0.73
0.49
0.34
180
300
600
700
1100
1250
B43044A9106M***
B43044A9226M***
B43044A9336M***
B43044A9476M***
B43044A9686M***
B43044A9107M***
10
12.5
12.5
16
16
18
18
× 20
× 20
× 25
× 25
× 31.5
× 31.5
× 35.5
6.5
3.6
2.5
1.7
1.1
0.93
0.71
150
200
315
570
620
900
980
B43044A5335M***
B43044A5475M***
B43044A5106M***
B43044A5226M***
B43044A5336M***
B43044A5476M***
B43044A5686M***
standard leads, bulk
kinked leads, bulk
cut leads, bulk
taped leads, Ammo pack,
taped leads, Ammo pack,
taped leads, Ammo pack,
taped leads, Ammo pack,
lead
lead
lead
lead
Please read Cautions and warnings and
Important notes at the end of this document.
spacing
spacing
spacing
spacing
a
a
a
a
=
=
=
=
14
2.0
2.5
3.5
5.0
mm
mm
mm
mm
08/08
AEC-C_B41044_B43044.book Seite 15 Dienstag, 5. August 2008 4:13 16
Single-ended capacitors
Taping, packing and lead configurations
B41044, B43044
Taping, packing and lead configurations of single-ended capacitors
Single-ended capacitors are available taped in Ammo pack from diameter 4 to 10 mm as follows:
Lead spacing 2.0 mm (∅ d = 4 ... 5 mm)
Last 3 digits of ordering code: 016
ød
P
∆h
P0
W2
1 max.
View B
Base tape
Adhesive tape
l1
t
W
W1
W0
H
H0
D0
∆h
F
P1
B
KAL1138-D-E
Dimensions in mm
∅d
F
4 ... 5 2.0
–0.2
H
W
W0
W1
W2
P
P0
P1
l1
t
∆h
D0
18.5
18.0
7.0
9.0
3.0
12.7
12.7
5.10
1.0
0.7
1
4.0
min.
±0.5
max.
±1.0
±0.3
±0.7
max.
±0.2
±1.0
±0.2
±0.75 ±0.5
Please read Cautions and warnings and
Important notes at the end of this document.
15
08/08
AEC-C_B41044_B43044.book Seite 16 Dienstag, 5. August 2008 4:13 16
Single-ended capacitors
Taping, packing and lead configurations
B41044, B43044
Lead spacing 2.5 mm (∅ d = 4 ... 6.3 mm)
Last 3 digits of ordering code: 007
ød
P
∆h
P0
∆h
View B
t
W
W0
W1
H
H0
W2
1 max.
P1
l1
D0
F
Base tape
Adhesive tape
B
KAL1074-3-E
Dimensions in mm
∅d
F
H
H0
W0
W1
W2
P
4 ... 6.3
2.5
18.5
16.0 18.0 7.0
9.0
3.0
12.7 12.7 5.10 1.0
W
P0
P1
l1
t
∆h
D0
0.7
0
4.0
Tolerance –0.2 ±0.75 ±0.5 ±0.5 min. ±0.5 max. ±1.0 ±0.3 ±0.7 max. ±0.2 ±1.0 ±0.2
Lead spacing 3.5 mm (∅ d = 8 mm)
Last 3 digits of ordering code: 006
ød
P
∆h
P0
W2
1 max.
View B
Base tape
Adhesive tape
l1
t
W
W1
W0
H
H0
D0
∆h
F
P1
B
KAL1138-D-E
Dimensions in mm
∅d
F
H
W
W0
W1
W2
P
8
3.5
18.5
18.0 10
9.0
3.0
12.7 12.7 5.10 1.0
Tolerance ±0.5 ±0.75 ±0.5 min.
Please read Cautions and warnings and
Important notes at the end of this document.
P0
P1
l1
t
∆h
D0
0.7
1
4.0
±0.5 max. ±1.0 ±0.3 ±0.7 max. ±0.2 max. ±0.2
16
08/08
AEC-C_B41044_B43044.book Seite 17 Dienstag, 5. August 2008 4:13 16
Single-ended capacitors
Taping, packing and lead configurations
B41044, B43044
Lead spacing 5.0 mm (∅ d = 4 ... 8 mm)
Last 3 digits of ordering code: 008
ød
P
P0
∆h
∆h
View B
t
W
W1
W0
H
H0
W2
1 max.
D0
F
P1
l1
Base tape
Adhesive tape
B
KAL1075-B-E
Lead spacing 5.0 mm (∅ d = 10 mm)
Last 3 digits of ordering code: 008
ød
P
∆h
P0
∆h
View B
t
W
W0
W1
H
W2
1 max.
D0
F
P1
l1
Base tape
Adhesive tape
B
KAL1076-J-E
Dimensions in mm
∅d
F
H
H0
W
W0
W1
W2
P
P0
P1
L1
t
∆h
D0
4 ... 6.3
5.0
18.5
16
18.0 7.0
9.0
3.0
12.7 12.7 3.85 1.0
0.6
2.0
4.0
8
5.0
18.5
16
18.0 10
9.0
3.0
12.7 12.7 3.85 1.0
0.6
2.0
4.0
10
5.0
18.5
–
18.0 12.5 9.0
3.0
12.7 12.7 3.85 1.0
0.6
2.0
4.0
Tolerance
+0.6 ±0.75 ±0.5 +1.0 +1.0 ±0.5 max. ±0.5 ±0.3 ±0.7 max. +0.3 max. ±0.2
–0.2
–0.5 –0
–0.2
Taping is available up to dimensions d × l = 10 × 20 mm. For ∅ 12.5, 16 and 18 mm taping is not
available.
Please read Cautions and warnings and
Important notes at the end of this document.
17
08/08
AEC-C_B41044_B43044.book Seite 18 Dienstag, 5. August 2008 4:13 16
Single-ended capacitors
Taping, packing and lead configurations
B41044, B43044
Kinked or cut leads
Single-ended capacitors are available with kinked or cut leads. Other lead configurations also available on request.
Kinked leads
Last 3 digits of ordering code: 001
2.1±0.1
ød
1.2±0.1
l
3.2±0.1
KAL1137-5
a
ød
l
4.5±0.5
KAL1084-A
Case size d × l (mm)
a (mm)
Case size d × l (mm) a (mm)
4×7
1.5
12.5 × 16
5.0
5×7
2.0
12.5 × 20
5.0
5 × 11
2.0
12.5 × 25
5.0
6.3 × 7
2.5
12.5 × 31.5
5.0
6.3 × 11
2.5
12.5 × 35.5
5.0
6.3 × 15
2.5
12.5 × 40
5.0
8×7
3.5
16 × 20
7.5
8 × 11.5
3.5
16 × 25
7.5
8 × 15
3.5
16 × 31.5
7.5
8 × 20
3.5
16 × 35.5
7.5
10 × 12.5
5.0
16 × 40
7.5
10 × 16
5.0
18 × 20
7.5
10 × 20
5.0
18 × 25
7.5
10 × 25
5.0
18 × 31.5
7.5
10 × 31.5
5.0
18 × 35.5
7.5
18 × 40
7.5
Please read Cautions and warnings and
Important notes at the end of this document.
18
08/08
AEC-C_B41044_B43044.book Seite 19 Dienstag, 5. August 2008 4:13 16
Single-ended capacitors
Taping, packing and lead configurations
B41044, B43044
Cut leads
Last 3 digits of ordering code: 002
a
ød
l
4.5±0.5
KAL1086-R
Case size d × l (mm)
a (mm)
Case size d × l (mm) a (mm)
4×7
1.5
12.5 × 16
5.0
5×7
2.0
12.5 × 20
5.0
5 × 11
2.0
12.5 × 25
5.0
6.3 × 7
2.5
12.5 × 31.5
5.0
6.3 × 11
2.5
12.5 × 35.5
5.0
6.3 × 15
2.5
12.5 × 40
5.0
8×7
3.5
16 × 20
7.5
8 × 11.5
3.5
16 × 25
7.5
8 × 15
3.5
16 × 31.5
7.5
8 × 20
5.0
16 × 35.5
7.5
10 × 12.5
5.0
16 × 40
7.5
10 × 16
5.0
18 × 20
7.5
10 × 20
5.0
18 × 25
7.5
10 × 25
5.0
18 × 31.5
7.5
10 × 31.5
5.0
18 × 35.5
7.5
18 × 40
7.5
Please read Cautions and warnings and
Important notes at the end of this document.
19
08/08
AEC-C_B41044_B43044.book Seite 20 Dienstag, 5. August 2008 4:13 16
Cautions and warnings
General
Also see “Important notes” on page 22.
1
Aluminum electrolytic capacitors have a bi-polar structure. This is marked on the body of the
capacitor. A capacitor must not be mounted with reversed polarity. The application of an AC
or reverse voltage may cause a short circuit or damage the capacitor. Bi-polar capacitors
must not be used in AC applications, where the polarity may be reversed in the circuits or is
unknown.
2
The DC voltage applied to the capacitor terminal must not exceed its rated operating voltage,
as this will result in a rapid increase of the leakage current and may damage the capacitor. It
is recommended to operate the capacitor at 70–80% of its rated voltage to optimize its service life.
3
The ripple current applied to the capacitor must be within the permitted range. An excessive
ripple current leads to impaired electrical properties and may damage the capacitor. Note that
the sum of the peak values of the ripple voltage and the DC operating voltage must not exceed the rated DC voltage.
4
Capacitors must be used within their permitted range of operating temperature. Operation at
room temperature optimizes their service life.
5
Capacitors with case diameter ≥8 mm are equipped with a safety vent. In capacitors fitted
with a lead or soldering lug, the safety vent is usually located at the base of the case. It needs
sufficient space around it to operate optimally. The following dimensions are recommended:
for case diameter d = 8 to 16 mm, more than 2 mm; for d =18 to 35 mm, more than 3 mm;
and for d = 42 mm or more, more than 5 mm.
6
Capacitors should not be mounted with the safety vent face down on the board. Do not locate
any wire or copper trace near the safety vent. Do not reverse the voltage, as this may result
in excess pressure and the leakage of electrolyte.
7
Gas is released through the safety vent when the pressure inside the capacitor is too high. A
gaseous liquid around the safety vent does not indicate a leakage of electrolyte.
8
The capacitor should be stored under conditions of normal temperature and in a non-acid,
non-alkali environment of normal humidity. Exposure to high temperatures, for example under direct sunlight, will reduce its operating life. If the capacitor is stored in an environment
containing acids or alkalis, the solderability of the leads may be affected.
9
The leakage current of an aluminum electrolytic capacitor may increase after a long period
of storage. After such storage, the capacitor must be aged by applying the rated operating
voltage for 6–8 hours before use.
10
Manual soldering:
a Soldering must be performed within the specified conditions.
Bit temperature: 350 °C; application time of soldering iron: 3 seconds.
b Ensure that the soldering iron does not touch any part of the capacitor body.
Please read Cautions and warnings and
Important notes at the end of this document.
20
08/08
AEC-C_B41044_B43044.book Seite 21 Dienstag, 5. August 2008 4:13 16
Cautions and warnings
11
Do not apply excessive force to the leads and terminals. Do not move the capacitor after soldering it onto the PC board and do not carry the PC board by gripping the capacitor. Observe
the following rules to prevent undue stress to the capacitor:
a Do not tilt or bend the capacitor after soldering.
b Ensure that the terminal spacing matches the corresponding hole spacing on the PC
board.
12
The aluminum case is not insulated from the cathode. Do not place a conductor under the
aluminum capacitors on the PC board as this may cause a short circuit. The case and top of
capacitors used in switched mode power supplies have a high-voltage-resistant heat shrink
sleeve to ensure safe usage.
13
The leads of capacitors with a case diameter exceeding 14 mm cannot be used for fixing.
Please read Cautions and warnings and
Important notes at the end of this document.
21
08/08
AEC-C_B41044_B43044.book Seite 22 Dienstag, 5. August 2008 4:13 16
Important notes
Important notes
The following applies to all products named in this publication:
1. Some parts of this publication contain statements about the suitability of our products for
certain areas of application. These statements are based on our knowledge of typical
requirements that are often placed on our products in the areas of application concerned. We
nevertheless expressly point out that such statements cannot be regarded as binding
statements about the suitability of our products for a particular customer application. As
a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them
than the customers themselves. For these reasons, it is always ultimately incumbent on the
customer to check and decide whether an EPCOS product with the properties described in the
product specification is suitable for use in a particular customer application.
2. We also point out that in individual cases, a malfunction of electronic components or failure
before the end of their usual service life cannot be completely ruled out in the current state
of the art, even if they are operated as specified. In customer applications requiring a very
high level of operational safety and especially in customer applications in which the malfunction
or failure of an electronic component could endanger human life or health (e.g. in accident
prevention or life-saving systems), it must therefore be ensured by means of suitable design of
the customer application or other action taken by the customer (e.g. installation of protective
circuitry or redundancy) that no injury or damage is sustained by third parties in the event of
malfunction or failure of an electronic component.
3. The warnings, cautions and product-specific notes must be observed.
4. In order to satisfy certain technical requirements, some of the products described in this
publication may contain substances subject to restrictions in certain jurisdictions (e.g.
because they are classed as hazardous). Useful information on this will be found in our
Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more
detailed questions, please contact our sales offices.
5. We constantly strive to improve our products. Consequently, the products described in this
publication may change from time to time. The same is true of the corresponding product
specifications. Please check therefore to what extent product descriptions and specifications
contained in this publication are still applicable before or when you place an order.
We also reserve the right to discontinue production and delivery of products. Consequently,
we cannot guarantee that all products named in this publication will always be available. The
aforementioned does not apply in case of individual agreements deviating from the foregoing for
customer-specific products.
6. Unless otherwise agreed in individual contracts, all orders are subject to the current version
of the “General Terms of Delivery for Products and Services in the Electrical Industry”
published by the German Electrical and Electronics Industry Association (ZVEI).
7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CSSP, CTVS, DSSP, MiniBlue, MKK,
MLSC, MotorCap, PCC, PhaseCap, PhaseMod, SIFERRIT, SIFI, SIKOREL, SilverCap,
SIMDAD, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap are trademarks
registered or pending in Europe and in other countries. Further information will be found on
the Internet at www.epcos.com/trademarks.
22
08/08