AM1DR-N Series DC-DC CONVERTERS 1 watt dc-dc converters • 7PIN SIP PACKAGE • INPUT/OUTPUT ISOLATION: 1000VDC • REGULATED OUTPUT VOLTAGE • OPERATING TEMPERATURE: -40°C ... +85°C • LOW RIPPLE & NOISE • PIN-COMPATIBLE WITH MULTIPLE MANUFACTURERS • HIGH EFFICIENCY UP TO 79% • UL94-VO PACKAGE GENERAL DESCRIPTION Our AM1DR-N series is a family of cost effective 1W single output isolated DC-DC converters. These converters achieve low cost and ultra-miniature SIP7 pin size without compromising performance and reliability. Twelve models operates from input voltages of 5, 12 & 24VDC; producing regulated output voltage levels of 5, 9, 12, 15VDC. Full SMD-design and a 100% production test of parameters ensures a high reliability in this product. ELECTRICAL SPECIFICATIONS Specifications typical at +25°C, nominal input voltage, rated output current unless otherwise specified Input Specifications: Voltage range Filter ±5% Capacitor Isolation Specifications: Rated voltage (60 sec) Resistance Capacitance 1000VDC > 1000MOhm 60pF, typ. Output Specifications: Voltage accuracy Ripple & noise (at 20MHz BW) Short circuit protection Line voltage regulation Load voltage regulation Temperature coefficient ±3%, max. 50 mVp-p, typ. 1 sec. ±0.5%, max. ±0.5%, max. ±0.02%/ºC, typ. General Specifications: Efficiency Switching frequency 72% to 79% 100KHz, typ. 100% load Environmental Specifications: Operating temperature (ambient) -40°C ... +85°C Storage temperature -55°C ... +125°C Case temperature +95°C, max. Derating None required Humidity (non-condensing) Up to 90% Cooling Free-air Convection Physical Specifications: Dimensions Weight Case material 19.6x6.0x10.2mm 0.77x0.24x0.4inches 2.7g Plastic UL94-VO MTBF: > 900,000 hrs (MIL-HDBK-217F, Ground Benign, t=+25ºC) Specifications are subject to change without notification OUTLINE DIMENSIONS & PIN CONNECTIONS Pin 1000VDC Single 22 1 2 4 5 6 7 +V Input -V Input -V Output Omitted +V Output Omitted TO ORDER CALL 1-888-9-AIMTEC AM1DR-N Series MODELS AM1DR-0505S-N AM1DR-0509S-N AM1DR-0512S-N AM1DR-0515S-N AM1DR-1205S-N AM1DR-1209S-N AM1DR-1212S-N AM1DR-1215S-N AM1DR-2405S-N AM1DR-2409S-N AM1DR-2412S-N AM1DR-2415S-N Input Voltage 5V±5% 12V±5% 24V±5% Ouput Voltage Ouput Current max. 5VDC 9VDC 12VDC 15VDC 5VDC 9VDC 12VDC 15VDC 5VDC 9VDC 12VDC 15VDC 150mA 111mA 83mA 67mA 150mA 111mA 83mA 67mA 150mA 111mA 83mA 67mA DC-DC CONVERTERS Models TYPICAL CHARACTERISTICS APPLICATION NOTE Filtering In some circuits which are sensitive to noise and ripple, a filtering capacitor may be added to the DC/DC output end and input end to reduce the noise and ripple. However, the capacitance of the output filter capacitor must be proper. If the capacitance is too big, a startup problem might arise. For every channel of output, provided the safe and reliable operation is ensured, the greatest capacitance of its filter capacitor sees the external capacitor table. To get an extremely low ripple, an “LC” filtering network may be connected to the input and output ends of the DC/DC converter, which may produce a more significant filtering effect. It should also be noted that the inductance and the frequency of the “LC” filtering network should be staggered with the DC/DC frequency to avoid mutual interference (see figure 1). Requirement On Output Load To ensure this module can operate efficiently and reliably, a minimum load is specified for this kind of DC/DC converter in addition to a maximum load (namely full load). During operation, make sure the specified range of input voltage is not exceeded, the minimum output load is not less than 10% of the full load, and that this product should never be operated under no load! If the actual output power is very small, please connect a resistor with proper resistance at the output end in parallel to increase the load. External Capacitor Table Vin External Capacitor Vout External Capacitor 5VDC 12VDC 24VDC - 4.7uF 2.2uF 1uF - 5VDC 9VDC 12VDC 15VDC 10uF 4.7uF 2.2uF 1uF 23 VISIT US AT WWW.AIMTEC.CA