MITSUBISHI IGBT MODULES CM400DY-24NF HIGH POWER SWITCHING USE CM400DY-24NF ¡IC ................................................................... 400A ¡VCES ......................................................... 1200V ¡Insulated Type ¡2-elements in a pack APPLICATION General purpose inverters & Servo controls, etc OUTLINE DRAWING & CIRCUIT DIAGRAM Dimensions in mm Tc measured point (Base plate) C1 29 7 18 6 TAB #110. t=0.5 8.5 18 4-φ6.5 MOUNTING HOLES LABEL C2E1 E2 21.2 7 +1.0 –0.5 18 21.5 25 E2 G2 25 G1 E1 15 80 62±0.25 3-M6 NUTS C1 G1 E1 E2 30 (20.5) C2E1 4 6 14 E2 G2 14 110 93±0.25 14 CIRCUIT DIAGRAM Mar.2003 MITSUBISHI IGBT MODULES CM400DY-24NF HIGH POWER SWITCHING USE MAXIMUM RATINGS (Tj = 25°C) Symbol VCES VGES IC ICM IE (Note 1) IEM (Note 1) PC (Note 3) Tj Tstg Viso — — — Parameter Collector-emitter voltage Gate-emitter voltage Collector current Emitter current Maximum collector dissipation Junction temperature Storage temperature Isolation voltage Torque strength Weight Conditions G-E Short C-E Short DC, TC’ = 111°C*3 Pulse Ratings 1200 ±20 400 800 400 800 1470 –40 ~ +150 –40 ~ +125 2500 3.5 ~ 4.5 3.5 ~ 4.5 580 (Note 2) Pulse TC = 25°C (Note 2) Main Terminal to base plate, AC 1 min. Main Terminal M6 Mounting holes M6 Typical value Unit V V A A A A W °C °C V N•m N•m g ELECTRICAL CHARACTERISTICS (Tj = 25°C) Symbol Parameter Test conditions Limits Typ. — Max. 1 Unit ICES Collector cutoff current VCE = VCES, VGE = 0V Min. — VGE(th) Gate-emitter threshold voltage IC = 40mA, VCE = 10V 6 7 8 V IGES Gate leakage current Collector-emitter saturation voltage Cies Coes Cres QG td(on) tr td(off) tf trr (Note 1) Qrr (Note 1) VEC(Note 1) Rth(j-c)Q Rth(j-c)R Rth(c-f) Rth(j-c’)Q RG Input capacitance Output capacitance Reverse transfer capacitance Total gate charge Turn-on delay time Turn-on rise time Turn-off delay time Turn-off fall time Reverse recovery time Reverse recovery charge Emitter-collector voltage — — — — — — — — — — — — — — — — — — 0.73 — 1.8 2.0 — — — 2700 — — — — — 16 — — — 0.02 — — 0.5 2.5 — 94 8 1.8 — 600 160 700 350 250 — 3.2 0.085 0.15 — µA VCE(sat) VGE = VGES, VCE = 0V Tj = 25°C IC = 400A, VGE = 15V Tj = 125°C Thermal resistance*1 Contact thermal resistance Thermal resistance VCE = 10V VGE = 0V VCC = 600V, IC = 400A, VGE = 15V VCC = 600V, IC = 400A VGE1 = VGE2 = 15V RG = 0.73Ω, Inductive load switching operation IE = 400A IE = 400A, VGE = 0V IGBT part (1/2 module) FWDi part (1/2 module) Case to fin, Thermal compound Applied*2 (1/2 module) Tc measured point is just under the chips External gate resistance 0.034*3 7.3 mA V nF nF nF nC ns ns ns ns ns µC V °C/W °C/W °C/W °C/W Ω *1 : Tc measured point is shown in page OUTLINE DRAWING. *2 : Typical value is measured by using Shin-etsu Silicone “G-746”. *3 : Tc’ measured point is just under the chips. If you use this value, Rth(f-a) should be measured just under the chips. Note 1. IE, VEC, trr & Qrr represent characteristics of the anti-parallel, emitter to collector free-wheel diode (FWDi). 2. Pulse width and repetition rate should be such that the device junction temp. (Tj) does not exceed Tjmax rating. 3. Junction temperature (Tj) should not increase beyond 150°C. Mar.2003 MITSUBISHI IGBT MODULES CM400DY-24NF HIGH POWER SWITCHING USE PERFORMANCE CURVES COLLECTOR-EMITTER SATURATION VOLTAGE CHARACTERISTICS (TYPICAL) 700 600 13 12 11 400 300 10 200 100 9 2 0 4 6 8 10 4 VGE = 15V 3 2 1 Tj = 25°C Tj = 125°C 0 100 200 300 400 500 600 700 800 0 COLLECTOR-EMITTER VOLTAGE VCE (V) COLLECTOR CURRENT IC (A) COLLECTOR-EMITTER SATURATION VOLTAGE CHARACTERISTICS (TYPICAL) FREE-WHEEL DIODE FORWARD CHARACTERISTICS (TYPICAL) 10 103 Tj = 25°C 7 8 6 4 IC = 400A IC = 800A 2 EMITTER CURRENT IE (A) COLLECTOR-EMITTER SATURATION VOLTAGE VCE (sat) (V) Tj = 25°C 15 500 0 CAPACITANCE Cies, Coes, Cres (nF) VGE = 20V 5 3 2 102 7 5 3 2 Tj = 25°C Tj = 125°C IC = 160A 0 6 8 10 12 14 16 18 101 20 102 7 5 3 2 Cies 101 7 5 3 2 3 4 5 HALF-BRIDGE SWITCHING CHARACTERISTICS (TYPICAL) 104 100 2 CAPACITANCE–VCE CHARACTERISTICS (TYPICAL) 7 5 3 2 7 5 3 2 1 EMITTER-COLLECTOR VOLTAGE VEC (V) 103 7 5 3 2 0 GATE-EMITTER VOLTAGE VGE (V) Coes Cres VGE = 0V 10–1 –1 10 2 3 5 7 100 2 3 5 7 101 2 3 5 7 102 COLLECTOR-EMITTER VOLTAGE VCE (V) SWITCHING TIME (ns) COLLECTOR CURRENT IC (A) 800 COLLECTOR-EMITTER SATURATION VOLTAGE VCE (sat) (V) OUTPUT CHARACTERISTICS (TYPICAL) td(off) 103 7 5 3 2 td(on) tf 102 7 5 3 2 tr Conditions: VCC = 600V, VGE = ±15V, RG = 0.73Ω Tj = 125°C, Inductive load 101 1 10 2 3 5 7 102 2 3 5 7 103 COLLECTOR CURRENT IC (A) Mar.2003 MITSUBISHI IGBT MODULES CM400DY-24NF TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (IGBT part & FWDi part) REVERSE RECOVERY CHARACTERISTICS OF FREE-WHEEL DIODE (TYPICAL) 103 7 5 3 Irr 2 trr 102 7 5 3 2 101 1 10 2 3 5 7 102 Conditions: VCC = 600V VGE = ±15V RG = 0.73Ω Tj = 25°C Inductive load 2 3 5 7 103 EMITTER CURRENT IE (A) 10–3 2 3 5 710–2 2 3 5 710–1 2 3 5 7 100 2 3 5 7 101 100 NORMALIZED TRANSIENT THERMAL IMPEDANCE Zth (j–c) REVERSE RECOVERY TIME trr (ns) REVERSE RECOVERY CURRENT lrr (A) HIGH POWER SWITCHING USE 7 5 3 2 Single Pulse TC = 25°C 10–1 10–1 7 5 3 2 7 5 3 2 IGBT part: 10–2 Per unit base = 7 5 Rth(j–c) = 0.085°C/W FWDi part: 3 Per unit base = 2 Rth(j–c) = 0.15°C/W –3 10 10–2 7 5 3 2 10–3 10–5 2 3 5 710–4 2 3 5 7 10–3 TMIE (s) GATE CHARGE CHARACTERISTICS (TYPICAL) GATE-EMITTER VOLTAGE VGE (V) 20 IC = 400A VCC = 400V 16 VCC = 600V 12 8 4 0 0 500 1000 2000 3000 4000 1500 2500 3500 GATE CHARGE QG (nC) Mar.2003