NXP ADC1613D080HN Dual 16-bit adc; 65 msps, 80 msps, 105 msps or 125 msps; serial jesd204a interface Datasheet

ADC1613D series
Dual 16-bit ADC; 65 Msps, 80 Msps, 105 Msps or 125 Msps;
serial JESD204A interface
Rev. 3 — 9 February 2011
Product data sheet
1. General description
The ADC1613D is a dual-channel 16-bit Analog-to-Digital Converter (ADC) optimized for
high dynamic performance and low power at sample rates up to 125 Msps. Pipelined
architecture and output error correction ensure the ADC1613D is accurate enough to
guarantee zero missing codes over the entire operating range. Supplied from a 3.3 V
source for analog and a 1.8 V source for the output driver, it embeds two serial outputs.
Each lane is differential and complies with the JESD204A standard. An integrated Serial
Peripheral Interface (SPI) allows the user to easily configure the ADC. A set of IC
configurations is also available via the binary level control pins taken, which are used at
power-up. The device also includes a programmable full-scale SPI to allow a flexible input
voltage range of 1 V to 2 V (peak-to-peak).
Excellent dynamic performance is maintained from the baseband to input frequencies of
170 MHz or more, making the ADC1613D ideal for use in communications, imaging, and
medical applications.
2. Features and benefits
„ SNR, 72.5 dBFS; SFDR, 88 dBc
„ Sample rate up to 125 Msps
„ Clock input divided by 2 for less jitter
contribution
„ 3 V, 1.8 V single supplies
„ Flexible input voltage range:
1 V (p-p) to 2 V (p-p)
„ Two configurable serial outputs
„ Compliant with JESD204A serial
transmission standard
„ Pin compatible with the ADC1413D
series, the ADC1213D series and the
ADC1113D125
„ Input bandwidth, 600 MHz
„ Power dissipation, 995 mW at 80 Msps
„ SPI register programming
„ Duty Cycle Stabilizer (DCS)
„ High IF capability
„ Offset binary, two’s complement, gray
code
„ Power-down mode and Sleep mode
„ HVQFN56 package
ADC1613D series
NXP Semiconductors
Dual 16-bit ADC: serial JESD204A interface
3. Applications
„ Wireless and wired broadband
communications
„ Spectral analysis
„ Ultrasound equipment
„ Portable instrumentation
„ Imaging systems
„ Software defined radio
4. Ordering information
Table 1.
Ordering information
Type number
Sampling
frequency
(Msps)
Package
Name
Description
ADC1613D125HN/C1 125
HVQFN56
plastic thermal enhanced very thin quad flat package; SOT684-7
no leads; 56 terminals; body 8 × 8 × 0.85 mm
ADC1613D105HN/C1 105
HVQFN56
plastic thermal enhanced very thin quad flat package; SOT684-7
no leads; 56 terminals; body 8 × 8 × 0.85 mm
ADC1613D080HN/C1 80
HVQFN56
plastic thermal enhanced very thin quad flat package; SOT684-7
no leads; 56 terminals; body 8 × 8 × 0.85 mm
ADC1613D065HN/C1 65
HVQFN56
plastic thermal enhanced very thin quad flat package; SOT684-7
no leads; 56 terminals; body 8 × 8 × 0.85 mm
ADC1613D_SER
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 9 February 2011
Version
© NXP B.V. 2011. All rights reserved.
2 of 43
ADC1613D series
NXP Semiconductors
Dual 16-bit ADC: serial JESD204A interface
5. Block diagram
CFG (0 to 3)
SDIO
SCLK
ERROR
CORRECTION AND
DIGITAL
PROCESSING
CS
SPI
SYNCP
SYNCN
INAP
SWING_n
8-bit
FRAME ASSEMBLY
CLOCK INPUT
STAGE AND DUTY
CYCLE CONTROL
CLKP
DLL
PLL
CLKM
ERROR
CORRECTION AND
DIGITAL
PROCESSING
8-bit
OTR
INBP
T/H
INPUT
STAGE
8-bit
ADC B CORE
16-BIT
PIPELINED
8-bit
ENCODER 8-bit/10-bit B
OTR
INAM
ENCODER 8-bit/10-bit A
D15 to D0
SCRAMBLER A
ADC A CORE
16-BIT
PIPELINED
SCRAMBLER B
T/H
INPUT
STAGE
SERIALIZER A
CMLPA
OUTPUT
BUFFER A
CMLNA
SERIALIZER B
CMLPB
OUTPUT
BUFFER B
CMLNB
10-bit
10-bit
D15 to D0
SWING_n
INBM
CLOCK INPUT
STAGE AND DUTY
CYCLE CONTROL
SYSTEM
REFERENCE AND
POWER
MANAGEMENT
ADC1613D
SCRAMBLER RESET
REFBT
REFAB
REFBB
REFAT
VCMB
VCMA
SENSE VREF
Fig 1.
005aaa168
Block diagram
ADC1613D_SER
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 9 February 2011
© NXP B.V. 2011. All rights reserved.
3 of 43
ADC1613D series
NXP Semiconductors
Dual 16-bit ADC: serial JESD204A interface
6. Pinning information
43 SYNCP
44 SYNCN
45 DGND
46 VDDD
47 SWING_0
48 SWING_1
49 DNC
50 VDDA
51 AGND
52 AGND
53 VDDA
54 SENSE
55 VREF
56 VDDA
6.1 Pinning
INAP
1
42 DGND
INAM
2
41 DGND
VCMA
3
40 VDDD
REFAT
4
39 CMLPA
REFAB
5
38 CMLNA
AGND
6
37 VDDD
CLKP
7
CLKM
8
AGND
9
36 DGND
ADC1613D
35 DGND
34 VDDD
REFBB 10
33 CMLNB
REFBT 11
32 CMLPB
DGND 28
VDDD 27
CFG3 26
CFG2 25
CFG1 24
CFG0 23
SCRAMBLER 22
RESET 21
AGND 20
CS 19
SDIO 18
29 DGND
SCLK 17
30 DGND
INBP 14
VDDA 16
31 VDDD
INBM 13
VDDA 15
VCMB 12
005aaa169
Transparent top view
Fig 2.
Pinning diagram
6.2 Pin description
ADC1613D_SER
Product data sheet
Table 2.
Pin description
Symbol
Pin
Type [1]
Description
INAP
1
I
channel A analog input
INAM
2
I
channel A complementary analog input
VCMA
3
O
channel A output common voltage
REFAT
4
O
channel A top reference
REFAB
5
O
channel A bottom reference
AGND
6
G
analog ground
CLKP
7
I
clock input
CLKM
8
I
complementary clock input
AGND
9
G
analog ground
REFBB
10
O
channel B bottom reference
REFBT
11
O
channel B top reference
VCMB
12
O
channel B output common voltage
INBM
13
I
channel B complementary analog input
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 9 February 2011
© NXP B.V. 2011. All rights reserved.
4 of 43
ADC1613D series
NXP Semiconductors
Dual 16-bit ADC: serial JESD204A interface
ADC1613D_SER
Product data sheet
Table 2.
Pin description …continued
Symbol
Pin
Type [1]
Description
INBP
14
I
channel B analog input
VDDA
15
P
analog power supply 3 V
VDDA
16
P
analog power supply 3 V
SCLK
17
I
SPI clock
SDIO
18
I/O
SPI data IO
CS
19
I
chip select
AGND
20
G
analog ground
RESET
21
I
JEDEC digital IP reset
SCRAMBLER
22
I
scrambler enable and disable
CFG0
23
I/O
Table 30 (input) or OTRA (output)[2]
CFG1
24
I/O
Table 30 (input) or OTRB (output)[2]
CFG2
25
I/O
Table 30 (input)
CFG3
26
I/O
Table 30 (input)
VDDD
27
P
digital power supply 1.8 V
DGND
28
G
digital ground
DGND
29
G
digital ground
DGND
30
G
digital ground
VDDD
31
P
digital power supply 1.8 V
CMLPB
32
O
channel B output
CMLNB
33
O
channel B complementary output
VDDD
34
P
digital power supply 1.8 V
DGND
35
G
digital ground
DGND
36
G
digital ground
VDDD
37
P
digital power supply 1.8 V
CMLNA
38
O
channel A complementary output
CMLPA
39
O
channel A output
VDDD
40
P
digital power supply 1.8 V
DGND
41
G
digital ground
DGND
42
G
digital ground
SYNCP
43
I
synchronization from FPGA
SYNCN
44
I
synchronization from FPGA
DGND
45
G
digital ground
VDDD
46
P
digital power supply 1.8 V
SWING_0
47
I
JESD204 serial buffer programmable output swing
SWING_1
48
I
JESD204 serial buffer programmable output swing
DNC
49
O
do not connect
VDDA
50
P
analog power supply 3 V
AGND
51
G
analog ground
AGND
52
G
analog ground
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 9 February 2011
© NXP B.V. 2011. All rights reserved.
5 of 43
ADC1613D series
NXP Semiconductors
Dual 16-bit ADC: serial JESD204A interface
Table 2.
Pin description …continued
Symbol
Pin
Type [1]
Description
VDDA
53
P
analog power supply 3 V
SENSE
54
I
reference programming pin
VREF
55
I/O
voltage reference input/output
VDDA
56
P
analog power supply 3 V
[1]
P: power supply; G: ground; I: input; O: output; I/O: input/output.
[2]
OTRA stands for “OuT of Range” A. OTRB stands for “OuT of Range” B.
7. Limiting values
Table 3.
Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134).
Symbol
Parameter
Min
Max
Unit
VDDA
analog supply voltage
Conditions
−0.4
+4.6
V
VDDD
digital supply voltage
−0.4
+2.5
V
Tstg
storage temperature
−55
+125
°C
Tamb
ambient temperature
−40
+85
°C
Tj
junction temperature
-
125
°C
8. Thermal characteristics
Table 4.
Symbol
Rth(j-a)
Rth(j-c)
[1]
ADC1613D_SER
Product data sheet
Thermal characteristics
Parameter
Conditions
Typ
Unit
thermal resistance from junction to ambient
[1]
17.8
K/W
thermal resistance from junction to case
[1]
6.8
K/W
Value for six layers board in still air with a minimum of 25 thermal vias.
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 9 February 2011
© NXP B.V. 2011. All rights reserved.
6 of 43
ADC1613D series
NXP Semiconductors
Dual 16-bit ADC: serial JESD204A interface
9. Static characteristics
Table 5.
Symbol
Static characteristics[1]
Parameter
Conditions
Min
Typ
Max
Unit
2.85
3.0
3.4
V
Supplies
VDDA
analog supply voltage
VDDD
digital supply voltage
1.65
1.8
1.95
V
IDDA
analog supply current
fclk = 125 Msps;
fi = 70 MHz
-
343
-
mA
IDDD
digital supply current
fclk = 125 Msps;
fi = 70 MHz
-
150
-
mA
Ptot
total power dissipation
fclk = 125 Msps
-
1270
-
mW
fclk = 105 Msps
-
1150
-
mW
fclk = 80 Msps
-
995
-
mW
P
power dissipation
fclk = 65 Msps
-
885
-
mW
Power-down mode
-
30
-
mW
Standby mode
-
200
-
mW
Clock inputs: pins CLKP and CLKM, AC coupled
Low-Voltage Positive Emitter-Coupled Logic (LVPECL)
Vi(clk)dif
differential clock input
voltage
peak-to-peak
-
1.6
-
V
differential clock input
voltage
peak
-
±3.0
-
V
SINE
Vi(clk)dif
Low Voltage Complementary Metal Oxide Semiconductor (LVCMOS)
VIL
LOW-level input voltage
-
-
0.3VDDA
V
VIH
HIGH-level input voltage
0.7VDDA
-
-
V
Logic inputs, Power-down: pins CFG0 to CFG3, SCRAMBLER, SWING_0, SWING_1, and RESET
VIL
LOW-level input voltage
-
0
-
V
VIH
HIGH-level input voltage
-
0.66VDDD
-
V
IIL
LOW-level input current
−6
-
+6
μA
IIH
HIGH-level input current
−30
-
+30
μA
-
0.3VDDA
V
SPI: pins CS, SDIO, and SCLK
VIL
LOW-level input voltage
0
VIH
HIGH-level input voltage
0.7VDDA
-
VDDA
V
IIL
LOW-level input current
−10
-
+10
μA
IIH
HIGH-level input current
−50
-
+50
μA
CI
input capacitance
-
4
-
pF
ADC1613D_SER
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 9 February 2011
© NXP B.V. 2011. All rights reserved.
7 of 43
ADC1613D series
NXP Semiconductors
Dual 16-bit ADC: serial JESD204A interface
Table 5.
Symbol
Static characteristics[1] …continued
Parameter
Conditions
Min
Typ
Max
Unit
Analog inputs: pins INAP, INAM, INBP, and INBM
II
input current
track mode
−5
-
+5
μA
RI
input resistance
track mode
-
15
-
Ω
CI
input capacitance
track mode
-
5
-
pF
VI(cm)
common-mode input
voltage
track mode
0.9
1.5
2
V
Bi
input bandwidth
-
600
-
MHz
VI(dif)
differential input voltage
1
-
2
V
peak-to-peak
Voltage controlled regulator output: pins VCMA and VCMB
VO(cm)
common-mode output
voltage
-
VDDA / 2
-
V
IO(cm)
common-mode output
current
-
4
-
mA
output
0.5
-
1
V
input
0.5
-
1
V
-
pin AGND;
VVREF; VDDA
-
V
Reference voltage input/output: pin VREF
VVREF
voltage on pin VREF
Reference mode selection: pin SENSE
VSENSE
voltage on pin SENSE
Data outputs: pins CMLPA, CMLNA
Output levels, VDDD = 1.8 V; SWING_SEL[2:0] = 000
VOL
VOH
LOW-level output
voltage
DC coupled; output
-
1.5
-
V
AC coupled
-
1.35
-
V
HIGH-level output
voltage
DC coupled; output
-
1.8
-
V
AC coupled
-
1.65
-
V
Output levels, VDDD = 1.8 V; SWING_SEL[2:0] = 001
VOL
LOW-level output
voltage
DC coupled; output
-
1.45
-
V
AC coupled
-
1.275
-
V
VOH
HIGH-level output
voltage
DC coupled; output
-
1.8
-
V
AC coupled
-
1.625
-
V
Output levels, VDDD = 1.8 V; SWING_SEL[2:0] = 010
VOL
VOH
LOW-level output
voltage
DC coupled; output
-
1.4
-
V
AC coupled
-
1.2
-
V
HIGH-level output
voltage
DC coupled; output
-
1.8
-
V
AC coupled
-
1.6
-
V
Output levels, VDDD = 1.8 V; SWING_SEL[2:0] = 011
VOL
VOH
LOW-level output
voltage
DC coupled; output
-
1.35
-
V
AC coupled
-
1.125
-
V
HIGH-level output
voltage
DC coupled; output
-
1.8
-
V
AC coupled
-
1.575
-
V
ADC1613D_SER
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 9 February 2011
© NXP B.V. 2011. All rights reserved.
8 of 43
ADC1613D series
NXP Semiconductors
Dual 16-bit ADC: serial JESD204A interface
Table 5.
Symbol
Static characteristics[1] …continued
Parameter
Conditions
Min
Typ
Max
Unit
Output levels, VDDD = 1.8 V; SWING_SEL[2:0] = 100
VOL
VOH
LOW-level output
voltage
DC coupled; output
-
1.3
-
V
AC coupled
-
1.05
-
V
HIGH-level output
voltage
DC coupled; output
-
1.8
-
V
AC coupled
-
1.55
-
V
Serial configuration: pins SYNCCP, SYNCCN
VIL
LOW-level input voltage
differential; input
-
0.95
-
V
VIH
HIGH-level input voltage differential; input
-
1.47
-
V
INL
integral non-linearity
-
±5
-
LSB
DNL
differential non-linearity
−0.95
±0.5
+0.95
LSB
Eoffset
offset error
-
±2
-
mV
EG
gain error
-
± 0.5
-
%
MG(CTC)
channel-to-channel gain
matching
-
1.1
-
%
-
−54
-
dB
Accuracy
no missing codes
guaranteed
full-scale
Supply
PSRR
[1]
power supply rejection
ratio
200 mV (p-p) on pin
VDDA; fi = DC
Typical values measured at VDDA = 3 V, VDDD = 1.8 V, Tamb = 25 °C. Minimum and maximum values are across the full temperature
range Tamb = −40 °C to +85 °C at VDDA = 3 V, VDDD = 1.8 V; VI (INAP, INBP) − VI (INAM, INBM) = −1 dBFS; internal reference mode;
100 Ω differential applied to serial outputs; unless otherwise specified.
ADC1613D_SER
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 9 February 2011
© NXP B.V. 2011. All rights reserved.
9 of 43
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
NXP Semiconductors
ADC1613D_SER
Product data sheet
10. Dynamic characteristics
10.1 Dynamic characteristics
Table 6.
Dynamic characteristics[1]
Symbol
Parameter
Conditions
ADC1613D065
ADC1613D080
ADC1613D105
ADC1613D125
Unit
Typ
Max
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
α2H
fi = 3 MHz
-
89
-
-
89
-
-
88
-
-
90
-
dBc
fi = 30 MHz
-
88
-
-
88
-
-
88
-
-
89
-
dBc
fi = 70 MHz
-
87
-
-
87
-
-
86
-
-
87
-
dBc
fi = 170 MHz
-
84
-
-
84
-
-
83
-
-
85
-
dBc
THD
ENOB
SNR
10 of 43
© NXP B.V. 2011. All rights reserved.
SFDR
third harmonic level
fi = 3 MHz
-
88
-
-
88
-
-
87
-
-
89
-
dBc
fi = 30 MHz
-
87
-
-
87
-
-
87
-
-
88
-
dBc
fi = 70 MHz
-
86
-
-
86
-
-
85
-
-
86
-
dBc
fi = 170 MHz
-
83
-
-
83
-
-
82
-
-
84
-
dBc
total harmonic distortion
fi = 3 MHz
-
85
-
-
85
-
-
84
-
-
86
-
dBc
fi = 30 MHz
-
84
-
-
84
-
-
84
-
-
85
-
dBc
fi = 70 MHz
-
83
-
-
83
-
-
82
-
-
83
-
dBc
fi = 170 MHz
-
80
-
-
80
-
-
79
-
-
81
-
dBc
effective number of bits
fi = 3 MHz
-
11.7
-
-
11.7
-
-
11.7
-
-
11.6
-
bits
fi = 30 MHz
-
11.6
-
-
11.6
-
-
11.6
-
-
11.6
-
bits
fi = 70 MHz
-
11.5
-
-
11.5
-
-
11.5
-
-
11.5
-
bits
fi = 170 MHz
-
11.4
-
-
11.4
-
-
11.4
-
-
11.4
-
bits
signal-to-noise ratio
fi = 3 MHz
-
72.3
-
-
72.2
-
-
72.0
-
-
71.6
-
dBFS
fi = 30 MHz
-
71.5
-
-
71.4
-
-
71.4
-
-
71.3
-
dBFS
fi = 70 MHz
-
70.9
-
-
70.9
-
-
70.8
-
-
70.7
-
dBFS
fi = 170 MHz
-
70.4
-
-
70.3
-
-
70.2
-
-
70.1
-
dBFS
spurious-free dynamic range
fi = 3 MHz
-
88
-
-
88
-
-
87
-
-
89
-
dBc
fi = 30 MHz
-
87
-
-
87
-
-
87
-
-
88
-
dBc
fi = 70 MHz
-
86
-
-
86
-
-
85
-
-
86
-
dBc
fi = 170 MHz
-
83
-
-
83
-
-
82
-
-
84
-
dBc
Dual 16-bit ADC: serial JESD204A interface
Rev. 3 — 9 February 2011
All information provided in this document is subject to legal disclaimers.
α3H
second harmonic level
ADC1613D series
Min
Analog signal processing
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Dynamic characteristics[1] …continued
Symbol
Parameter
IMD
αct(ch)
[1]
Conditions
intermodulation distortion
channel crosstalk
ADC1613D065
ADC1613D080
ADC1613D105
ADC1613D125
NXP Semiconductors
ADC1613D_SER
Product data sheet
Table 6.
Unit
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
fi = 3 MHz
-
89
-
-
89
-
-
88
-
-
89
-
dBc
fi = 30 MHz
-
88
-
-
88
-
-
88
-
-
88
-
dBc
fi = 70 MHz
-
87
-
-
87
-
-
86
-
-
86
-
dBc
fi = 170 MHz
-
84
-
-
85
-
-
83
-
-
84
-
dBc
fi = 70 MHz
-
100
-
-
100
-
-
100
-
-
100
-
dBc
Typical values measured at VDDA = 3 V, VDDD = 1.8 V, Tamb = 25 °C. Minimum and maximum values are across the full temperature range Tamb = −40 °C to +85 °C at VDDA = 3 V,
VDDD = 1.8 V; VI (INAP, INBP) − VI (INAM, INBM) = −1 dBFS; internal reference mode; 100 Ω differential applied to serial outputs; unless otherwise specified.
Table 7.
Symbol
Clock and digital output timing characteristics[1]
Parameter
Conditions
ADC1613D065
ADC1613D080
ADC1613D105
ADC1613D125
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
Unit
Clock timing input: pins CLKP and CLKM
clock frequency
40
-
65
60
-
80
75
-
105
100
-
125
Msps
tlat(data)
data latency time
17
-
20
17
-
20
17
-
20
17
-
20
clock
cycle
δclk
clock duty cycle
DCS_EN = 1: en
30
50
70
30
50
70
30
50
70
30
50
70
%
DCS_EN = 0: dis
45
50
55
45
50
55
45
50
55
45
50
55
%
td(s)
sampling delay time
-
0.8
-
-
0.8
-
-
0.8
-
-
0.8
-
ns
twake
wake-up time
-
76
-
-
76
-
-
76
-
-
76
-
μs
[1]
Typical values measured at VDDA = 3 V, VDDD = 1.8 V, Tamb = 25 °C. Minimum and maximum values are across the full temperature range Tamb = −40 °C to +85 °C at VDDA = 3 V,
VDDD = 1.8 V; VI (INAP, INBP) − VI (INAM, INBM) = −1 dBFS; internal reference mode; 100 Ω differential applied to serial outputs; unless otherwise specified.
11 of 43
© NXP B.V. 2011. All rights reserved.
ADC1613D series
fclk
Dual 16-bit ADC: serial JESD204A interface
Rev. 3 — 9 February 2011
All information provided in this document is subject to legal disclaimers.
10.2 Clock and digital output timing
ADC1613D series
NXP Semiconductors
Dual 16-bit ADC: serial JESD204A interface
10.3 Serial output timing
The eye diagram of the serial output is shown in Figure 3 and Figure 4. Test conditions
are:
• 3.125 Gbps data rate
• Tamb = 25 °C
• DC coupling with two different receiver common-mode voltages
005aaa088
Fig 3.
Eye diagram at 1 V receiver common-mode
005aaa089
Fig 4.
ADC1613D_SER
Product data sheet
Eye diagram at 2 V receiver common-mode
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 9 February 2011
© NXP B.V. 2011. All rights reserved.
12 of 43
ADC1613D series
NXP Semiconductors
Dual 16-bit ADC: serial JESD204A interface
10.4 SPI timing
Table 8.
SPI timing characteristics[1]
Symbol
Parameter
tw(SCLK)
Min
Typ
Max
Unit
SCLK pulse width
-
40
-
ns
tw(SCLKH)
SCLK HIGH pulse
width
-
16
-
ns
tw(SCLKL)
SCLK LOW pulse
width
-
16
-
ns
tsu
set-up time
data to SCLK H
-
5
-
ns
CS to SCLK H
-
5
-
ns
th
hold time
data to SCLK H
-
2
-
ns
CS to SCLK H
-
2
-
ns
-
25
-
MHz
fclk(max)
[1]
Conditions
maximum clock
frequency
Typical values measured at VDDA = 3 V, VDDD = 1.8 V, Tamb = 25 °C. Minimum and maximum values are
across the full temperature range Tamb = −40 °C to +85 °C at VDDA = 3 V, VDDD = 1.8 V; VI (INAP,
INBP) − VI (INAM,INBM) = −1 dBFS; internal reference mode; 100 Ω differential applied to serial outputs;
unless otherwise specified.
tsu
tsu
th
CS
tw(SCLKL)
th
tw(SCLKH)
tw(SCLK)
SCLK
SDIO
R/W
W1
W0
A12
A11
D2
D1
D0
005aaa065
Fig 5.
ADC1613D_SER
Product data sheet
SPI timing
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 9 February 2011
© NXP B.V. 2011. All rights reserved.
13 of 43
ADC1613D series
NXP Semiconductors
Dual 16-bit ADC: serial JESD204A interface
11. Application information
11.1 Analog inputs
11.1.1 Input stage description
The analog input of the ADC1613D supports a differential or a single-ended input drive.
Optimal performance is achieved using differential inputs with the common-mode input
voltage (VI(cm)) on pins INP and INM set to 0.5VDDA.
The full-scale analog input voltage range is configurable between 1 V (p-p) and 2 V (p-p)
via a programmable internal reference (see Section 11.2 and Table 21).
Figure 6 shows the equivalent circuit of the sample-and-hold input stage, including
ElectroStatic Discharge (ESD) protection and circuit and package parasitics.
package
ESD
parasitics
switch
INAP
INBP
1, 14
Ron = 15 Ω
4 pF
Cs
internal
clock
switch
INAM
INBM
2, 13
Ron = 15 Ω
4 pF
Cs
internal
clock
005aaa069
Fig 6.
Input sampling circuit
The sample phase occurs when the internal clock (derived from the clock signal on pin
CLKP/CLKM) is HIGH. The voltage is then held on the sampling capacitors. When the
clock signal goes LOW, the stage enters the hold phase and the voltage information is
transmitted to the ADC core.
11.1.2 Anti-kickback circuitry
Anti-kickback circuitry (Figure 7) is needed to counteract the effects of a charge injection
generated by the sampling capacitance.
The RC filter is also used to filter noise from the signal before it reaches the sampling
stage. The value of the capacitor should be chosen to maximize noise attenuation without
degrading the settling time excessively.
ADC1613D_SER
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 9 February 2011
© NXP B.V. 2011. All rights reserved.
14 of 43
ADC1613D series
NXP Semiconductors
Dual 16-bit ADC: serial JESD204A interface
INPA/
INBP
R
C
INAM/
INBM
R
001aan679
Fig 7.
Anti-kickback circuit
The component values are determined by the input frequency and should be selected so
as not to affect the input bandwidth.
Table 9.
RC coupling versus input frequency - typical values
Input frequency (MHz)
Resistance (Ω)
Capacitance (pF)
3
25
12
70
12
8
170
12
8
11.1.3 Transformer
The configuration of the transformer circuit is determined by the input frequency. The
configuration shown in Figure 8 would be suitable for a baseband application.
100 nF
Analog
input
100 nF
25 Ω
ADT1-1WT
INAP
INBP
25 Ω
12 pF
100 nF
100 nF
25 Ω
25 Ω
INAM
INBM
VCM
100 nF
100 nF
005aaa070
Fig 8.
ADC1613D_SER
Product data sheet
Single transformer configuration
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 9 February 2011
© NXP B.V. 2011. All rights reserved.
15 of 43
ADC1613D series
NXP Semiconductors
Dual 16-bit ADC: serial JESD204A interface
ADT1-1WT
Analog
input
100 nF
ADT1-1WT
50 Ω
12 Ω
INAP
INBP
50 Ω
8.2 pF
50 Ω
100 nF
50 Ω
12 Ω
INAM
INBM
VCM
100 nF
100 nF
005aaa071
Fig 9.
Dual transformer configuration
The configuration shown in Figure 9 is recommended for high frequency applications. In
both cases, the choice of transformer is a compromise between cost and performance.
11.2 System reference and power management
11.2.1 Internal/external reference
The ADC1613D has a stable and accurate built-in internal reference voltage to adjust the
ADC full-scale. This reference voltage can be set internally via SPI or with pins VREF and
SENSE (see Figure 11 to Figure 14), in 1 dB steps between 0 dB and −6 dB, via SPI
control bits INTREF[2:0] (when bit INTREF_EN = logic 1; see Table 21). The equivalent
reference circuit is shown in Figure 10. An external reference is also possible by providing
a voltage on pin VREF as described in Figure 13.
ADC1613D_SER
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 9 February 2011
© NXP B.V. 2011. All rights reserved.
16 of 43
ADC1613D series
NXP Semiconductors
Dual 16-bit ADC: serial JESD204A interface
REFAT/
REFBT
REFAB/
REFBB
REFERENCE
AMP
VREF
EXT_ref
BUFFER
EXT_ref
BANDGAP
REFERENCE
ADC CORE
SENSE
SELECTION
LOGIC
001aan670
Fig 10. Reference equivalent schematic
If bit INTREF_EN is set to logic 0, the reference voltage is determined either internally or
externally as detailed in Table 10.
Table 10.
Reference modes
Mode
SPI bit, “Internal
reference”
SENSE pin
VREF pin
Full-scale
(V (p-p))
Internal (Figure 11)
0
GND
330 pF capacitor 2
to GND
Internal (Figure 12)
0
VREF pin = SENSE pin and
330 pF capacitor to GND
External (Figure 13)
0
VDDA
Internal, SPI mode
(Figure 14)
1
VREF pin = SENSE pin and
330 pF capacitor to GND
1
external voltage 1 to 2
from 0.5 V to 1 V
1 to 2
Figure 11 to Figure 14 illustrate how to connect the SENSE and VREF pins to select the
required reference voltage source.
ADC1613D_SER
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 9 February 2011
© NXP B.V. 2011. All rights reserved.
17 of 43
ADC1613D series
NXP Semiconductors
Dual 16-bit ADC: serial JESD204A interface
VREF
VREF
330 pF
330
pF
REFERENCE
EQUIVALENT
SCHEMATIC
REFERENCE
EQUIVALENT
SCHEMATIC
SENSE
SENSE
005aaa117
005aaa116
Fig 11. Internal reference, 2 V (p-p) full-scale
Fig 12. Internal reference, 1 V (p-p) full-scale
VREF
VREF
V
0.1 μF
330 pF
REFERENCE
EQUIVALENT
SCHEMATIC
REFERENCE
EQUIVALENT
SCHEMATIC
SENSE
SENSE
VDDA
005aaa118
005aaa119
Fig 13. External reference, 1 V (p-p) to 2 V (p-p)
full-scale
Fig 14. Internal reference via SPI, 1 V (p-p) to 2 V (p-p)
full-scale
11.2.2 Programmable full-scale
The full-scale is programmable between 1 V (p-p) to 2 V (p-p) (see Table 11).
Table 11.
ADC1613D_SER
Product data sheet
Reference SPI gain control
INTREF[2:0]
Level (dB)
Full-scale (V (p-p))
000
0
2
001
−1
1.78
010
−2
1.59
011
−3
1.42
100
−4
1.26
101
−5
1.12
110
−6
1
111
not used
x
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 9 February 2011
© NXP B.V. 2011. All rights reserved.
18 of 43
ADC1613D series
NXP Semiconductors
Dual 16-bit ADC: serial JESD204A interface
11.2.3 Common-mode output voltage (VO(cm))
An 0.1 μF filter capacitor should be connected between the pins VCMA and VCMB and
ground to ensure a low-noise common-mode output voltage. When AC-coupled, these
pins can be used to set the common-mode reference for the analog inputs, for instance
via a transformer middle point.
PACKAGE
ESD
PARASITICS
COMMON MODE
REFERENCE
1.5 V
VCMA
VCMB
0.1 μF
ADC CORE
005aaa077
Fig 15. Reference equivalent schematic
11.2.4 Biasing
The common-mode input voltage, VI(cm), at the inputs to the sample-and-hold stage
(pins INAM, INBM, INAP, and INBP) must be between 0.9 V and 2 V for optimal
performance.
11.3 Clock input
11.3.1 Drive modes
The ADC1613D can be driven differentially (LVPECL). It can also be driven by a
single-ended LVCMOS signal connected to pin CLKP (pin CLKM should be connected to
ground via a capacitor) or pin CLKM (pin CLKP should be connected to ground via a
capacitor).
LVCMOS
clock input
CLKP
CLKP
CLKM
LVCMOS
clock input
005aaa053
005aaa174
a. Rising edge LVCMOS
CLKM
b. Falling edge LVCMOS
Fig 16. LVCMOS single-ended clock input
ADC1613D_SER
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 9 February 2011
© NXP B.V. 2011. All rights reserved.
19 of 43
ADC1613D series
NXP Semiconductors
Dual 16-bit ADC: serial JESD204A interface
Sine
clock input
CLKP
Sine
clock input
CLKP
CLKM
CLKM
005aaa173
005aaa054
a. Sine clock input
b. Sine clock input (with transformer)
CLKP
LVPECL
clock input
CLKM
005aaa172
c. LVPECL clock input
Fig 17. Differential clock input
11.3.2 Equivalent input circuit
The equivalent circuit of the input clock buffer is shown in Figure 18. The common-mode
voltage of the differential input stage is set via 5 kΩ internal resistors.
package
ESD
parasitics
CLKP
Vcm(clk)
SE_SEL
SE_SEL
5 kΩ
5 kΩ
CLKM
005aaa081
Vcm(clk) = common-mode voltage of the differential input stage.
Fig 18. Equivalent input circuit
ADC1613D_SER
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 9 February 2011
© NXP B.V. 2011. All rights reserved.
20 of 43
ADC1613D series
NXP Semiconductors
Dual 16-bit ADC: serial JESD204A interface
Single-ended or differential clock inputs can be selected via the SPI (see Table 20). If
single-ended is selected, the input pin (CLKM or CLKP) is selected via control bit
SE_SEL.
If single-ended is implemented without setting bit SE_SEL accordingly, the unused pin
should be connected to ground via a capacitor.
11.3.3 Clock input divider
The ADC1613D contains an input clock divider that divides the incoming clock by a factor
of 2 (when bit CLKDIV2_SEL = logic 1; see Table 20). This feature allows the user to
deliver a higher clock frequency with better jitter performance, leading to a better SNR
result once acquisition has been performed.
11.3.4 Duty cycle stabilizer
The duty cycle stabilizer can improve the overall performances of the ADC by
compensating the input clock signal duty cycle. When the duty cycle stabilizer is active
(bit DCS_EN = logic 1; see Table 20), the circuit can handle signals with duty cycles of
between 30 % and 70 % (typical). When the duty cycle stabilizer is disabled
(DCS_EN = logic 0), the input clock signal should have a duty cycle of between 45 % and
55 %.
Table 12.
Duty cycle stabilizer
Bit DCS_EN
Description
0
duty cycle stabilizer disable
1
duty cycle stabilizer enable
11.4 Digital outputs
11.4.1 Serial output equivalent circuit
The JESD204A standard specifies that if the receiver and the transmitter are DC-coupled,
both must be fed from the same supply.
VDDD
50 Ω
CMLPA/CLMPB
100 Ω
RECEIVER
CMLNA/CLMNB
+
−
12 mA to 26 mA
AGND
005aaa082
Fig 19. CML output connection to the receiver (DC-coupled)
The output should be terminated when 100 Ω (typical) is reached at the receiver side.
ADC1613D_SER
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 9 February 2011
© NXP B.V. 2011. All rights reserved.
21 of 43
ADC1613D series
NXP Semiconductors
Dual 16-bit ADC: serial JESD204A interface
VDDD
50 Ω
CMLPA/CMLPB
10 nF
CMLNA/CMLNB
−
+
100 Ω
RECEIVER
10 nF
12 mA to 26 mA
005aaa083
Fig 20. CML output connection to the receiver (AC-coupled)
11.5 JESD204A serializer
For more information about the JESD204A standard refer to the JEDEC web site.
11.5.1 Digital JESD204A formatter
The block placed after the ADC cores is used to implement all functionalities of the
JESD204A standard. This ensures signal integrity and guarantees the clock and the data
recovery at the receiver side.
The block is highly parameterized and can be configured in various ways depending on
the sampling frequency and the number of lanes used.
M CONVERTERS
N bits from Cr0 +
CS bits for control
L LANES
F octets
TX transport layer
FRAME
TO
OCTETS
SCRAMBLER
ALIGNMENT
CHARACTER
GENERATOR
8-bit/
10-bit
SER
LANE 0
8-bit/
10-bit
SER
LANE 1
TX CONTROLLER
SYNC~
samples stream to
lane stream mapping
N bits from CrM−1 +
CS bits for control
N' = N+CS
S samples per frame cycle
F octets
FRAME
TO
OCTETS
SCRAMBLER
ALIGNMENT
CHARACTER
GENERATOR
CF: position of control bits
HD: frame boundary break
Padding with Tail bits (TT)
Mx(N'xS) bits
Lx(F) octets
L octets
005aaa084
Fig 21. General overview of the JESD204A serializer
ADC1613D_SER
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 9 February 2011
© NXP B.V. 2011. All rights reserved.
22 of 43
ADC1613D series
NXP Semiconductors
Dual 16-bit ADC: serial JESD204A interface
ADC_MODE[1:0]
PRBS
DUMMY
SCR_IN_MODE
11
16
10
16
N
AND
CS
LANE_MODE[1:0]
16
8-bit/
10-bit
SCR
PRBS
ADC_PD
ADC A
00
8
N + CS
01
´1
frame CLK
´F
character CLK
´ 10F
FSM
(frame
assembly,
character
replication,
ILA,
test mode)
FRAME
ASSEMBLY
bit CLK
16
'0'
01
'0/1'
10
PRBS
11
PRBS
11
PRBS
16
10
16
N
AND
CS
'0/1'
10
'0'
01
SER
LANE_POL
01
8-bit/
10-bit
SCR
N + CS
8
10
00
00
LANE_MODE[1:0]
11
PRBS
SER
00
ADC_PD
DUMMY
LANE_POL
SWING_SEL[2:0]
sync_request
ADC B
00
00
bypass alignment
disable_char_repl
PLL
AND
DLL
10
SCR_IN_MODE
ADC_MODE[1:0]
005aaa170
Fig 22. Detailed view of the JESD204A serializer with debug functionality
11.5.2 ADC core output codes versus input voltage
Table 13 shows the data output codes for a given analog input voltage.
Table 13.
ADC1613D_SER
Product data sheet
Output codes versus input voltage
INP − INM (V)
Offset binary
Two’s complement
OTR
< −1
0000 0000 0000 0000
1000 0000 0000 0000
1
−1
0000 0000 0000 0000
1000 0000 0000 0000
0
−0.99996948
0000 0000 0000 0001
1000 0000 0000 0001
0
−0.99993896
0000 0000 0000 0010
1000 0000 0000 0010
0
−0.99990845
0000 0000 0000 0011
1000 0000 0000 0011
0
−0.99987793
0000 0000 0000 0100
1000 0000 0000 0100
0
....
....
....
0
−0.00006104
0111 1111 1111 1110
1111 1111 1111 1110
0
−0.00003052
0111 1111 1111 1111
1111 1111 1111 1111
0
0
1000 0000 0000 0000
0000 0000 0000 0000
0
+0.00003052
1000 0000 0000 0001
0000 0000 0000 0001
0
+0.00006104
1000 0000 0000 0010
0000 0000 0000 0010
0
....
....
....
0
+0.99987793
1111 1111 1111 1011
0111 1111 1111 1011
0
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 9 February 2011
© NXP B.V. 2011. All rights reserved.
23 of 43
ADC1613D series
NXP Semiconductors
Dual 16-bit ADC: serial JESD204A interface
Table 13.
Output codes versus input voltage …continued
INP − INM (V)
Offset binary
Two’s complement
OTR
+0.99990845
1111 1111 1111 1100
0111 1111 1111 1100
0
+0.99993896
1111 1111 1111 1101
0111 1111 1111 1101
0
+0.99996948
1111 1111 1111 1110
0111 1111 1111 1110
0
+1
1111 1111 1111 1111
0111 1111 1111 1111
0
> +1
1111 1111 1111 1111
0111 1111 1111 1111
1
11.6 Serial Peripheral Interface (SPI)
11.6.1 Register description
The ADC1613D serial interface is a synchronous serial communications port allowing for
easy interfacing with many industry microprocessors. It provides access to the registers
that control the operation of the chip in both read and write modes.
This interface is configured as a 3-wire type (SDIO as bidirectional pin).
Pin SCLK acts as the serial clock, and pin CS acts as the serial chip select.
Each read/write operation is sequenced by the CS signal and enabled by a LOW level to
to drive the chip with 2 bytes to 5 bytes, depending on the content of the instruction byte
(see Table 14).
Table 14.
SPI instruction bytes
MSB
LSB
Bit
7
6
5
4
3
2
1
0
Description
R/W[1]
W1
W0
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
[1]
R/W indicates whether a read (logic 1) or write (logic 0) transfer occurs after the instruction byte
Table 15.
Read or Write mode access description
R/W[1]
Description
0
Write mode operation
1
Read mode operation
[1]
Bits W1 and W0 indicate the number of bytes transferred after the instruction byte.
Table 16.
Number of bytes to be transferred
W1
W0
Number of bytes transferred
0
0
1 byte
0
1
2 bytes
1
0
3 bytes
1
1
4 or more bytes
Bits A12 to A0 indicate the address of the register being accessed. In the case of a
multiple byte transfer, this address is the first register to be accessed. An address counter
is incremented to access subsequent addresses.
ADC1613D_SER
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 9 February 2011
© NXP B.V. 2011. All rights reserved.
24 of 43
ADC1613D series
NXP Semiconductors
Dual 16-bit ADC: serial JESD204A interface
The steps for a data transfer:
1. A falling edge on pin CS in combination with a rising edge on pin SCLK determine the
start of communications.
2. The first phase is the transfer of the 2-byte instruction.
3. The second phase is the transfer of the data which can vary in length but always a
multiple of 8 bits. The MSB is always sent first (for instruction and data bytes)
4. A rising edge on pin CS indicates the end of data transmission.
CS
SCLK
SDIO
R/W
W1
W0
A12 A11 A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
Instruction bytes
D7
D6
D5
D4
D3
D2
Register N (data)
D1
D0
D7
D6
D5
D4
D3
D2
D1
D0
Register N + 1 (data)
005aaa086
Fig 23. Transfer diagram for two data bytes (3-wire type)
11.6.2 Channel control
The two ADC channels can be configured at the same time or separately. By using the
register “Channel index”, the user can choose which ADC channel receives the next
SPI-instruction. By default the channel A and B receives the same instructions in write
mode. In read mode only A is active.
ADC1613D_SER
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 9 February 2011
© NXP B.V. 2011. All rights reserved.
25 of 43
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
NXP Semiconductors
ADC1613D_SER
Product data sheet
Table 17.
Register allocation map
Address Register name
(hex)
Access[1]
Bit definition
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
ADCB
ADCA
Default
(bin)
ADC control register
Channel index
R/W
-
-
-
-
-
-
0005
Reset and
Power-down
modes
R/W
SW_RST
-
-
-
-
-
0006
Clock
R/W
-
-
-
SE_SEL
DIFF_SE
-
0008
Vref
R/W
-
-
-
-
INTREF_EN
0013
Offset
R/W
-
-
0014
Test pattern 1
R/W
-
-
-
-
-
0015
Test pattern 2
R/W
TESTPAT_2[15:8]
0000 0000
0016
Test pattern 3
R/W
TESTPAT_3[7:0]
0000 0000
PD[1:0]
CLKDIV2_SEL
1111 1111
0000 0000
DCS_EN
0000 0001
INTREF[2:0]
0000 0000
TESTPAT_1[2:0]
0000 0000
DIG_OFFSET[5:0]
0000 0000
JESD204A control
Ser_Status
R
RXSYNC_
ERROR
RESERVED[2:0]
0
0
POR_TST
FSM_SW_
RST
0
0
RESERVED 0111 0000
0802
Ser_Reset
R/W
SW_RST
0
0
0
0803
Ser_Cfg_Setup
R/W
0
0
0
0
0805
Ser_Control1
R/W
0
TRISTATE_
CFG_PINS
SYNC_
POL
SYNC_
SINGLE_
ENDED
1
REV_
SCR
REV_
ENCODER
REV_
SERIAL
0100 1001
0806
Ser_Control2
R/W
0
0
0
0
0
0
SWAP_
LANE_0_1
SWAP_
ADC_A_B
0000 0011
0808
Ser_Analog_Ctrl
R/W
0
0
0
0
0
0809
Ser_ScramblerA
R/W
0
080A
Ser_ScramblerB
R/W
080B
Ser_PRBS_Ctrl
R/W
0820
Cfg_0_DID
R*
0821
Cfg_1_BID
R/W*
0
0
0
0
0822
Cfg_3_SCR_L
R/W*
SCR
0
0
0
0
0823
Cfg_4_F
R/W*
0
0
0
0
0
0824
Cfg_5_K
R/W*
0
0
0
0825
Cfg_6_M
R/W*
0
0
0
0
CFG_SETUP[3:0]
0000 1000
SWING_SEL[2:0]
0000 0011
LSB_INIT[6:0]
0000 0000
MSB_INIT[7:0]
0
0
0
0
0
1111 1111
0
PRBS_TYPE[1:0]
DID[7:0]
BID[3:0]
0
0000 0000
1110 1101
0
0000 1010
0
L
F[2:0]
0
0000 0000
0000 0001
K[4:0]
0
0000 0000
0000 1000
0
M
0000 0000
ADC1613D series
26 of 43
© NXP B.V. 2011. All rights reserved.
0801
Dual 16-bit ADC: serial JESD204A interface
Rev. 3 — 9 February 2011
All information provided in this document is subject to legal disclaimers.
0003
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Register allocation map …continued
Address Register name
(hex)
Access[1]
0826
R/W*
Cfg_7_CS_N
Bit definition
Bit 7
Bit 6
Bit 5
Bit 4
0
CS[0]
0
0
Bit 3
Bit 2
Bit 1
Bit 0
N[3:0]
Default
(bin)
0100 0111
Cfg_8_Np
R/W
0
0
0
0828
Cfg_9_S
R/W*
0
0
0
0
0
NP[4:0]
0
0000 1111
0829
Cfg_10_HD_CF
R/W*
HD
0
0
0
0
0
082C
Cfg_01_2_LID
R/W*
0
0
0
082D
Cfg_02_2_LID
R/W*
0
0
0
084C
Cfg01_13_FCHK
R
FCHK[7:0]
0000 0000
084D
Cfg02_13_FCHK
R
FCHK[7:0]
0000 0000
0870
Lane0_0_Ctrl
R/W
0
SCR_IN_
MODE
LANE_MODE[1:0]
0
LANE_
POL
LANE_CLK_
POS_EDGE
LANE_PD
0000 0001
0871
Lane1_0_Ctrl
R/W
0
SCR_IN_
MODE
LANE_MODE[1:0]
0
LANE_
POL
LANE_CLK_
POS_EDGE
LANE_PD
0000 0000
0890
ADCA_0_Ctrl
R/W
0
0
ADC_MODE[1:0]
0
0
0
ADC_PD
0000 0001
0891
ADCB_0_Ctrl
R/W
0
0
ADC_MODE[1:0]
0
0
0
ADC_PD
0000 0000
0
S
CF[1:0]
0000 0000
0000 0000
LID[4:0]
0001 1011
LID[4:0]
0001 1100
an "*" in the Access column means that this register is subject to control access conditions in Write mode.
ADC1613D series
27 of 43
© NXP B.V. 2011. All rights reserved.
Dual 16-bit ADC: serial JESD204A interface
Rev. 3 — 9 February 2011
All information provided in this document is subject to legal disclaimers.
0827
[1]
NXP Semiconductors
ADC1613D_SER
Product data sheet
Table 17.
ADC1613D series
NXP Semiconductors
Dual 16-bit ADC: serial JESD204A interface
11.6.3 Register description
11.6.3.1
ADC control registers
Table 18. Register Channel index (address 0003h)
Default values are highlighted.
Bit
Access Value
Description
7 to 2 -
-
not used
1
R/W
0
Symbol
ADCB
ADCA
111111
ADC B gets the next SPI command:
0
ADC B not selected
1
ADC B selected
R/W
ADC A gets the next SPI command:
0
ADC A not selected
1
ADC A selected
Table 19. Register Reset and Power-down mode (address 0005h)
Default values are highlighted.
Bit
Symbol
Access Value
Description
7
SW_RST
R/W
reset digital part:
6 to 2 -
-
1 to 0 PD[1:0]
R/W
0
no reset
1
performs a reset of the digital part
00000
not used
power-down mode:
00
normal (power-up)
01
full power-down
10
sleep
11
normal (power-up)
Table 20. Register Clock (address 0006h)
Default values are highlighted.
Bit
Symbol
Access Value
7 to 5 -
-
4
R/W
3
SE_SEL
DIFF_SE
-
-
1
CLKDIV2_SEL
R/W
DCS_EN
ADC1613D_SER
Product data sheet
not used
select SE clock input pin:
0
select CLKM input
1
select CLKP input
R/W
2
0
000
Description
differential/single-ended clock input select:
0
fully differential
1
single-ended
0
not used
select clock input divider by 2:
0
disable
1
active
R/W
duty cycle stabilizer enable:
0
disable
1
active
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 9 February 2011
© NXP B.V. 2011. All rights reserved.
28 of 43
ADC1613D series
NXP Semiconductors
Dual 16-bit ADC: serial JESD204A interface
Table 21. Register Vref (address 0008h)
Default values are highlighted.
Bit
Symbol
Access Value
7 to 4 -
-
3
R/W
INTREF_EN
2 to 0 INTREF[2:0]
0000
Description
not used
enable internal programmable VREF mode:
0
disable
1
active
R/W
programmable internal reference:
000
0 dB (FS=2 V)
001
−1 dB (FS=1.78 V)
010
−2 dB (FS=1.59 V)
011
−3 dB (FS=1.42 V)
100
−4 dB (FS=1.26 V)
101
−5 dB (FS=1.12 V)
110
−6 dB (FS=1 V)
111
not used
Table 22. Digital offset adjustment (address 0013h)
Default values are highlighted.
Register offset
Decimal
DIG_OFFSET[5:0]
+31
011111
+31 LSB
...
...
...
0
000000
0
...
...
...
−32
100000
−32 LSB
Table 23. Register Test pattern 1 (address 0014h)
Default values are highlighted.
Access Value
Description
7 to 3 -
Bit
Symbol
-
not used
2 to 0 TESTPAT_1[2:0]
R/W
00000
digital test pattern:
000
ADC1613D_SER
Product data sheet
off
001
mid-scale
010
− FS
011
+ FS
100
toggle ‘1111..1111’/’0000..0000’
101
custom test pattern, to be written in register 0015h and 0016h
110
‘010101...’
111
‘101010...’
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 9 February 2011
© NXP B.V. 2011. All rights reserved.
29 of 43
ADC1613D series
NXP Semiconductors
Dual 16-bit ADC: serial JESD204A interface
Table 24. Register Test pattern 2 (address 0015h)
Default values are highlighted.
Bit
Symbol
7 to 0 TESTPAT_2[15:8]
Access Value
R/W
Description
00000000 custom digital test pattern (bit 15 to 8)
Table 25. Register Test pattern 3 (address 0016h)
Default values are highlighted.
Bit
Symbol
7 to 0 TESTPAT_3[7:0]
Access Value
R/W
Description
00000000 custom digital test pattern (bit 7 to 0)
11.6.4 JESD204A digital control registers
Table 26. Ser_Status (address 0801h)
Default values are highlighted.
Bit
Symbol
Access Value
Description
7
RXSYNC_ERROR
R
set to 1 when a synchronization error occurs
0
6 to 4 RESERVED[2:0]
-
111
reserved
3 to 2 -
-
00
not used
1
POR_TST
R
0
power-on-reset
0
RESERVED
-
0
reserved
Table 27. SER_Reset (address 0802h)
Default values are highlighted.
Bit
Symbol
Access Value
Description
7
SW_RST
R/W
0
initiates a software reset of the JESD204A unit
6 to 4 -
-
000
not used
3
R/W
0
initiates a software reset of the internal state machine of
JESD204A unit
-
000
not used
FSM_SW_RST
2 to 0 -
ADC1613D_SER
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 9 February 2011
© NXP B.V. 2011. All rights reserved.
30 of 43
ADC1613D series
NXP Semiconductors
Dual 16-bit ADC: serial JESD204A interface
Table 28. SER_Cfg_Setup (address 0803h)
Default values are highlighted.
Bit
Symbol
Access Value
Description
7 to 4 -
-
0000
not used
3 to 0 CFG_SETUP[3:0]
R/W
1000
quick configuration of JESD204A. These settings overrule the
configuration of pins CFG3 to CFG0 (see Table 29).
Table 29.
JESD204A configuration table
CFG_SETUP[3:0] ADC A
ADC B
Lane 0
Lane 1
F[1] HD[1] K[1] M[1] L[1]
Comment
CS[1] CF[1] S[1]
0
0000
ON
ON
ON
ON
2
0
9
2
2
(F × K) ≥ 17
0
0
1
1
0001
ON
ON
ON
OFF
4
0
5
2
1
(F × K) ≥ 17
0
0
1
2
0010
ON
ON
OFF
ON
4
0
5
2
1
(F × K) ≥ 17
0
0
1
3
0011
ON
OFF
ON
ON
1
1
17
1
2
(F × K) ≥ 17
0
0
1
4
0100
OFF
ON
ON
ON
1
1
17
1
2
(F × K) ≥ 17
0
0
1
5
0101
ON
OFF
ON
OFF
2
0
9
1
1
(F × K) ≥ 17
0
0
1
6
0110
ON
OFF
OFF
ON
2
0
9
1
1
(F × K) ≥ 17
0
0
1
7
0111
OFF
ON
ON
OFF
2
0
9
1
1
(F × K) ≥ 17
0
0
1
8
1000
OFF
ON
OFF
ON
2
0
9
1
1
(F × K) ≥ 17
0
0
1
9
1001
reserved
10
1010
reserved
11
1011
reserved
12
1100
reserved
13
1101
reserved
14
1110
ON
ON
ON
ON
2
0
9
2
2
test: loop
alignment
0
0
1
15
1111
OFF
OFF
OFF
OFF
2
0
9
2
2
chip
power-down
0
0
1
[1]
F: Octets per frame clock cycle
HD: High-density mode
K: Frame per multi-frame
M: Converters per device
L: Lane per converter device
CS: Number of control bits per conversion sample
CF: Control words per frame clock cycle and link
S: Number of samples transmitted per single converter per frame cycle
ADC1613D_SER
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 9 February 2011
© NXP B.V. 2011. All rights reserved.
31 of 43
ADC1613D series
NXP Semiconductors
Dual 16-bit ADC: serial JESD204A interface
Table 30. SER_Control1 (address 0805h)
Default values are highlighted.
Bit
Symbol
Access Value
Description
7
-
-
0
not used
6
TRISTATE_CFG_PINS
R/W
1
pins CFG3 to CFG0 are set to high-impedance. Switch to 0
automatically after start-up or reset.
5
SYNC_POL
R/W
4
SYNC_SINGLE_ENDED
defines the sync signal polarity:
0
synchronization signal is active LOW
1
synchronization signal is active HIGH
R/W
defines the input mode of the sync signal:
0
synchronization input mode is set in Differential mode
1
3
-
-
2
REV_SCR
-
synchronization input mode is set in Single-ended mode
1
not used
LSBs are swapped with MSBs at the scrambler input:
0
disable
1
1
0
REV_ENCODER
REV_SERIAL
enable
-
LSBs are swapped with MSBs at the 8-bit/10-bit encoder input:
0
disable
1
enable
-
LSBs are swapped with MSBs at the lane input:
0
disable
1
enable
Table 31. SER_Control2 (address 0806h)
Default values are highlighted.
Bit
Access Value
Description
7 to 2 -
-
not used
1
R/W
0
Symbol
SWAP_LANE_0_1
SWAP_ADC_A_B
000000
swaps the outputs of the JESD204A unit (output buffer A is
connected to Lane 1, output buffer B is connected to Lane 0)
0
disable
1
enable
R/W
swaps the inputs of the JESD204A unit (ADC A output is
connected to ADC input B, ADC B is connected to ADC input A)
0
disable
1
enable
Table 32. SER_Analog_Ctrl (address 0808h)
Default values are highlighted.
Bit
Symbol
Access Value
Description
7 to 3 -
-
00000
not used
2 to 0 SWING_SEL[2:0]
R/W
011
defines the swing of output buffers A and B
ADC1613D_SER
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 9 February 2011
© NXP B.V. 2011. All rights reserved.
32 of 43
ADC1613D series
NXP Semiconductors
Dual 16-bit ADC: serial JESD204A interface
Table 33. SER_ScramblerA (address 0809h)
Default values are highlighted.
Bit
Symbol
Access Value
7
-
-
0
not used
R/W
0000000
defines the initialization vector for the scrambler polynomial
(lower)
6 to 0 LSB_INIT[6:0]
Description
Table 34. SER_ScramblerB (address 080Ah)
Default values are highlighted.
Bit
Symbol
7 to 0 MSB_INIT[7:0]
Access Value
Description
R/W
defines the initialization vector for the scrambler polynomial
(upper)
11111111
Table 35. SER_PRBS_Ctrl (address 080Bh)
Default values are highlighted.
Bit
Symbol
Access Value
Description
7 to 2 -
-
not used
1 to 0 PRBS_TYPE[1:0]
R/W
000000
defines the type of Pseudo-Random Binary Sequence (PRBS)
generator to be used:
00 (reset)
PRBS-7
01
PRBS-7
10
PRBS-23
11
PRBS-31
Table 36. Cfg_0_DID (address 0820h)
Default values are highlighted.
Bit
Symbol
7 to 0 DID[7:0]
Access Value
Description
R
defines the device (= link) identification number
11101101
Table 37. Cfg_1_BID (address 0821h)
Default values are highlighted.
Access Value
Description
7 to 4 -
Bit
Symbol
-
0000
not used
3 to 0 BID[3:0]
R/W
1010
defines the bank ID – extension to DID
Table 38. Cfg_3_SCR_L (address 0822h)
Default values are highlighted.
Bit
Symbol
Access Value
Description
7
SCR
R/W
0
scrambling enabled
6 to 1 -
-
000000
not used
0
R/W
0
defines the number of lanes per converter device, minus 1
L
Table 39. Cfg_4_F (address 0823h)
Default values are highlighted.
Bit
Symbol
Access Value
Description
7 to 3 -
-
00000
not used
2 to 0 F[2:0]
R/W
001
defines the number of octets per frame, minus 1
ADC1613D_SER
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 9 February 2011
© NXP B.V. 2011. All rights reserved.
33 of 43
ADC1613D series
NXP Semiconductors
Dual 16-bit ADC: serial JESD204A interface
Table 40. Cfg_5_K (address 0824h)
Default values are highlighted.
Bit
Symbol
Access Value
Description
7 to 5 -
-
000
not used
4 to 0 K[4:0]
R/W
01000
defines the number of frames per multiframe, minus 1
Table 41. Cfg_6_M (address 0825h)
Default values are highlighted.
Access Value
Description
7 to 1 -
Bit
Symbol
-
0000000
not used
0
R/W
0
defines the number of converters per device, minus 1
M
Table 42. Cfg_7_CS_N (address 0826h)
Default values are highlighted.
Bit
Symbol
Access Value
Description
7
-
-
0
not used
6
CS[0]
R/W
1
defines the number of control bits per sample, minus 1
5 to 4 -
-
00
not used
3 to 0 N[3:0]
R/W
0111
defines the converter resolution
Table 43. Cfg_8_Np (address 0827h)
Default values are highlighted.
Access Value
Description
7 to 5 -
Bit
Symbol
-
000
not used
4 to 0 NP[4:0]
R/W
01111
defines the total number of bits per sample, minus 1
Table 44. Cfg_9_S (address 0828h)
Default values are highlighted.
Bit
Symbol
Access Value
Description
7 to 1 -
-
0000000
not used
0
R/W
0
defines number of samples per converter per frame cycle
S
Table 45. Cfg_10_HD_CF (address 0829h)
Default values are highlighted.
Bit
Symbol
Access Value
Description
7
HD
R/W
defines high density format
0
6 to 2 -
-
00000
not used
1 to 0 CF[1:0]
R/W
00
defines number of control words per frame clock cycle per link.
Table 46. Cfg01_2_LID (address 082Ch)
Default values are highlighted.
Access Value
Description
7 to 5 -
Bit
Symbol
-
000
not used
4 to 0 LID[4:0]
R/W
11011
defines lane 0 identification number
ADC1613D_SER
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 9 February 2011
© NXP B.V. 2011. All rights reserved.
34 of 43
ADC1613D series
NXP Semiconductors
Dual 16-bit ADC: serial JESD204A interface
Table 47. Cfg02_2_LID (address 082Dh)
Default values are highlighted.
Bit
Symbol
Access Value
Description
7 to 5 -
-
000
not used
4 to 0 LID[4:0]
R/W
11100
defines lane 1 identification number
Table 48. Cfg01_13_FCHK (address 084Ch)
Default values are highlighted.
Bit
Symbol
7 to 0 FCHK[7:0]
Access Value
R
Description
00000000 defines the checksum value for lane 0
checksum corresponds to the sum of all the link configuration
parameters module 256 (as defined in JEDEC Standard
No.204A)
Table 49. Cfg02_13_FCHK (address 084Dh)
Default values are highlighted.
Bit
Symbol
7 to 0 FCHK[7:0]
Access Value
R
Description
00000000 defines the checksum value for lane 1
checksum corresponds to the sum of all the link configuration
parameters module 256 (as defined in JEDEC Standard
No.204A)
Table 50. Lane0_0_Ctrl (address 0870h)
Default values are highlighted.
Bit
Symbol
Access Value
Description
7
-
-
not used
6
SCR_IN_MODE
R/W
5 to 4 LANE_MODE[1:0]
-
-
2
LANE_POL
R/W
LANE_CLK_POS_EDGE
ADC1613D_SER
Product data sheet
defines the input type for scrambler and 8-bit/10-bit units:
0 (reset)
(normal mode) = input of the scrambler and 8-bit/10-bit
units is the output of the frame assembly unit.
1
input of the scrambler and 8-bit/10-bit units is the PRBS
generator (PRBS type is defined with “PRBS_TYPE”
(Ser_PRBS_ctrl register)
R/W
3
1
0
defines output type of lane output unit:
00 (reset)
normal mode: lane output is the 8-bit/10-bit output unit
01
constant mode: lane output is set to a constant (0 × 0)
10
toggle mode: lane output is toggling between 0 × 0 and 0 × 1
11
PRBS mode: lane output is the PRSB generator (PRBS type is
defined with “PRBS_TYPE” (Ser_PRBS_Ctrl register)
0
not used
defines lane polarity:
0
lane polarity is normal
1
lane polarity is inverted
R/W
defines lane clock polarity:
0
lane clock provided to the serializer is active on positive
edge
1
lane clock provided to the serializer is active on negative edge
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 9 February 2011
© NXP B.V. 2011. All rights reserved.
35 of 43
ADC1613D series
NXP Semiconductors
Dual 16-bit ADC: serial JESD204A interface
Table 50. Lane0_0_Ctrl (address 0870h) …continued
Default values are highlighted.
Bit
Symbol
Access Value
Description
0
LANE_PD
R/W
lane power-down control:
0
lane is operational
1
lane is in Power-down mode
Table 51. Lane1_0_ctrl (address 0871h)
Default values are highlighted.
Bit
Symbol
7
-
-
6
SCR_IN_MODE
R/W
5 to 4 LANE_MODE[1:0]
Access Value
0
-
-
2
LANE_POL
R/W
0 (reset)
(normal mode) = input of the scrambler and 8-bit/10-bit
units is the output of the frame assembly unit.
1
input of the scrambler and 8-bit/10-bit units is the PRBS
generator (PRBS type is defined with “PRBS_TYPE”
(Ser_PRBS_Ctrl register)
defines output type of lane output unit:
00 (reset)
normal mode: lane output is the 8-bit/10-bit output unit
01
constant mode: lane output is set to a constant (0x0)
10
toggle mode: lane output is toggling between 0x0 and 0x1
11
PRBS mode: lane output is the PRBS generator (PRBS type is
defined with “PRBS_TYPE” (Ser_PRBS_Ctrl register)
0
1
LANE_CLK_POS_EDGE
R/W
1
LANE_PD
ADC1613D_SER
Product data sheet
lane polarity is normal
lane polarity is inverted
defines lane clock polarity:
0
0
not used
defines lane polarity:
0
1
not used
defines the input type for scrambler and 8-bit/10-bit units:
R/W
3
Description
R/W
lane clock provided to the serializer is active on positive
edge
lane clock provided to the serializer is active on negative edge
lane power-down control:
0
lane is operational
1
lane is in Power-down mode
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 9 February 2011
© NXP B.V. 2011. All rights reserved.
36 of 43
ADC1613D series
NXP Semiconductors
Dual 16-bit ADC: serial JESD204A interface
Table 52. ADCA_0_ctrl (address 0890h)
Default values are highlighted.
Bit
Symbol
Access Value
Description
7 to 6 -
-
not used
5 to 4 ADC_MODE[1:0]
R/W
3 to 1 -
-
0
R/W
ADC_PD
00
defines input type of JESD204A unit:
00 (reset)
ADC output is connected to the JESD204A input
01
not used
10
JESD204A input is fed with a dummy constant, set to:
ADC[15:0] = “1001101110101000”
11
JESD204A is fed with a PRBS generator (PRBS type is
defined with “PRBS_TYPE” (Ser_PRBS_ctrl register)
000
not used
ADC power-down control:
0
ADC is operational
1
ADC is in Power-down mode
Table 53. ADCB_0_ctrl (address 0891h)
Default values are highlighted.
Bit
Symbol
Access Value
Description
7 to 6 -
-
not used
5 to 4 ADC_MODE[1:0]
R/W
3 to 1 -
-
0
R/W
ADC_PD
ADC1613D_SER
Product data sheet
00
defines input type of JESD204A unit
00 (reset)
ADC output is connected to the JESD204A input
01
not used
10
JESD204A input is fed with a dummy constant, set to:
ADC[15:0] = “1001101110101000”
11
JESD204A is fed with a PRBS generator (PRBS type is
defined with “PRBS_TYPE” (Ser_PRBS_ctrl register)
000
not used
ADC power-down control:
0
ADC is operational
1
ADC is in Power-down mode
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 9 February 2011
© NXP B.V. 2011. All rights reserved.
37 of 43
ADC1613D series
NXP Semiconductors
Dual 16-bit ADC: serial JESD204A interface
12. Package outline
HVQFN56: plastic thermal enhanced very thin quad flat package; no leads;
56 terminals; body 8 x 8 x 0.85 mm
A
B
D
SOT684-7
terminal 1
index area
A
E
A1
c
detail X
e1
e
1/2 e
L
15
28
14
C
C A B
C
v
w
b
y1 C
y
29
e
e2
Eh
1/2 e
1
42
terminal 1
index area
56
43
X
Dh
0
2.5
scale
Dimensions
Unit
A(1)
A1
b
max 1.00 0.05 0.30
nom 0.85 0.02 0.21
min 0.80 0.00 0.18
mm
5 mm
c
D(1)
Dh
E(1)
Eh
0.2
8.1
8.0
7.9
5.95
5.80
5.65
8.1
8.0
7.9
6.55
6.40
6.25
e
e1
0.5
6.5
e2
L
v
6.5
0.5
0.4
0.3
0.1
w
y
0.05 0.05
y1
0.1
Note
1. Plastic or metal protrusions of 0.075 mm maximum per side are not included.
References
Outline
version
IEC
JEDEC
JEITA
SOT684-7
---
MO-220
---
sot684-7_po
European
projection
Issue date
08-11-19
09-03-04
Fig 24. Package outline SOT684-7 (HVQFN56)
ADC1613D_SER
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 9 February 2011
© NXP B.V. 2011. All rights reserved.
38 of 43
ADC1613D series
NXP Semiconductors
Dual 16-bit ADC: serial JESD204A interface
13. Abbreviations
Table 54.
ADC1613D_SER
Product data sheet
Abbreviations
Acronym
Description
ADC
Analog-to-Digital Converter
DCS
Duty Cycle Stabilizer
ESD
ElectroStatic Discharge
IF
Intermediate Frequency
IMD
InterModulation Distortion
LSB
Least Significant Bit
LVCMOS
Low Voltage Complementary Metal Oxide Semiconductor
LVPECL
Low-Voltage Positive Emitter-Coupled Logic
MSB
Most Significant Bit
OTR
OuT-of-Range
PRBS
Pseudo-Random Binary Sequence
SFDR
Spurious-Free Dynamic Range
SNR
Signal-to-Noise Ratio
SPI
Serial Peripheral Interface
TX
Transmitter
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 9 February 2011
© NXP B.V. 2011. All rights reserved.
39 of 43
ADC1613D series
NXP Semiconductors
Dual 16-bit ADC: serial JESD204A interface
14. Revision history
Table 55.
Revision history
Document ID
Release date
Data sheet status
Change notice
Supersedes
ADC1613D_SER v.3
20110209
Product data sheet
-
ADC1613D_SER v.2
Modifications:
•
•
•
•
•
Data sheet status changed from Preliminary to Product.
Text and drawings updated throughout entire data sheet.
Table 29 “JESD204A configuration table” added to Section 11.6.4.
All tables in Section 11.6.2 have been updated.
Section 13 “Abbreviations” added to the data sheet.
ADC1613D_SER v.2
20100423
Preliminary data sheet
-
ADC1613D_SER v.1
ADC1613D_SER v.1
20100413
Objective data sheet
-
-
ADC1613D_SER
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 9 February 2011
© NXP B.V. 2011. All rights reserved.
40 of 43
ADC1613D series
NXP Semiconductors
Dual 16-bit ADC: serial JESD204A interface
15. Legal information
15.1 Data sheet status
Document status[1][2]
Product status[3]
Definition
Objective [short] data sheet
Development
This document contains data from the objective specification for product development.
Preliminary [short] data sheet
Qualification
This document contains data from the preliminary specification.
Product [short] data sheet
Production
This document contains the product specification.
[1]
Please consult the most recently issued document before initiating or completing a design.
[2]
The term ‘short data sheet’ is explained in section “Definitions”.
[3]
The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status
information is available on the Internet at URL http://www.nxp.com.
15.2 Definitions
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. NXP Semiconductors does not give any
representations or warranties as to the accuracy or completeness of
information included herein and shall have no liability for the consequences of
use of such information.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is intended
for quick reference only and should not be relied upon to contain detailed and
full information. For detailed and full information see the relevant full data
sheet, which is available on request via the local NXP Semiconductors sales
office. In case of any inconsistency or conflict with the short data sheet, the
full data sheet shall prevail.
Product specification — The information and data provided in a Product
data sheet shall define the specification of the product as agreed between
NXP Semiconductors and its customer, unless NXP Semiconductors and
customer have explicitly agreed otherwise in writing. In no event however,
shall an agreement be valid in which the NXP Semiconductors product is
deemed to offer functions and qualities beyond those described in the
Product data sheet.
15.3 Disclaimers
Limited warranty and liability — Information in this document is believed to
be accurate and reliable. However, NXP Semiconductors does not give any
representations or warranties, expressed or implied, as to the accuracy or
completeness of such information and shall have no liability for the
consequences of use of such information.
In no event shall NXP Semiconductors be liable for any indirect, incidental,
punitive, special or consequential damages (including - without limitation - lost
profits, lost savings, business interruption, costs related to the removal or
replacement of any products or rework charges) whether or not such
damages are based on tort (including negligence), warranty, breach of
contract or any other legal theory.
Notwithstanding any damages that customer might incur for any reason
whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards
customer for the products described herein shall be limited in accordance
with the Terms and conditions of commercial sale of NXP Semiconductors.
malfunction of an NXP Semiconductors product can reasonably be expected
to result in personal injury, death or severe property or environmental
damage. NXP Semiconductors accepts no liability for inclusion and/or use of
NXP Semiconductors products in such equipment or applications and
therefore such inclusion and/or use is at the customer’s own risk.
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. NXP Semiconductors makes no
representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Customers are responsible for the design and operation of their applications
and products using NXP Semiconductors products, and NXP Semiconductors
accepts no liability for any assistance with applications or customer product
design. It is customer’s sole responsibility to determine whether the NXP
Semiconductors product is suitable and fit for the customer’s applications and
products planned, as well as for the planned application and use of
customer’s third party customer(s). Customers should provide appropriate
design and operating safeguards to minimize the risks associated with their
applications and products.
NXP Semiconductors does not accept any liability related to any default,
damage, costs or problem which is based on any weakness or default in the
customer’s applications or products, or the application or use by customer’s
third party customer(s). Customer is responsible for doing all necessary
testing for the customer’s applications and products using NXP
Semiconductors products in order to avoid a default of the applications and
the products or of the application or use by customer’s third party
customer(s). NXP does not accept any liability in this respect.
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) will cause permanent
damage to the device. Limiting values are stress ratings only and (proper)
operation of the device at these or any other conditions above those given in
the Recommended operating conditions section (if present) or the
Characteristics sections of this document is not warranted. Constant or
repeated exposure to limiting values will permanently and irreversibly affect
the quality and reliability of the device.
Terms and conditions of commercial sale — NXP Semiconductors
products are sold subject to the general terms and conditions of commercial
sale, as published at http://www.nxp.com/profile/terms, unless otherwise
agreed in a valid written individual agreement. In case an individual
agreement is concluded only the terms and conditions of the respective
agreement shall apply. NXP Semiconductors hereby expressly objects to
applying the customer’s general terms and conditions with regard to the
purchase of NXP Semiconductors products by customer.
Right to make changes — NXP Semiconductors reserves the right to make
changes to information published in this document, including without
limitation specifications and product descriptions, at any time and without
notice. This document supersedes and replaces all information supplied prior
to the publication hereof.
No offer to sell or license — Nothing in this document may be interpreted or
construed as an offer to sell products that is open for acceptance or the grant,
conveyance or implication of any license under any copyrights, patents or
other industrial or intellectual property rights.
Suitability for use — NXP Semiconductors products are not designed,
authorized or warranted to be suitable for use in life support, life-critical or
safety-critical systems or equipment, nor in applications where failure or
Export control — This document as well as the item(s) described herein
may be subject to export control regulations. Export might require a prior
authorization from national authorities.
ADC1613D_SER
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 9 February 2011
© NXP B.V. 2011. All rights reserved.
41 of 43
ADC1613D series
NXP Semiconductors
Dual 16-bit ADC: serial JESD204A interface
Non-automotive qualified products — Unless this data sheet expressly
states that this specific NXP Semiconductors product is automotive qualified,
the product is not suitable for automotive use. It is neither qualified nor tested
in accordance with automotive testing or application requirements. NXP
Semiconductors accepts no liability for inclusion and/or use of
non-automotive qualified products in automotive equipment or applications.
NXP Semiconductors’ specifications such use shall be solely at customer’s
own risk, and (c) customer fully indemnifies NXP Semiconductors for any
liability, damages or failed product claims resulting from customer design and
use of the product for automotive applications beyond NXP Semiconductors’
standard warranty and NXP Semiconductors’ product specifications.
In the event that customer uses the product for design-in and use in
automotive applications to automotive specifications and standards, customer
(a) shall use the product without NXP Semiconductors’ warranty of the
product for such automotive applications, use and specifications, and (b)
whenever customer uses the product for automotive applications beyond
15.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks
are the property of their respective owners.
16. Contact information
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: [email protected]
ADC1613D_SER
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 9 February 2011
© NXP B.V. 2011. All rights reserved.
42 of 43
ADC1613D series
NXP Semiconductors
Dual 16-bit ADC: serial JESD204A interface
17. Contents
1
General description . . . . . . . . . . . . . . . . . . . . . . 1
2
Features and benefits . . . . . . . . . . . . . . . . . . . . 1
3
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
4
Ordering information . . . . . . . . . . . . . . . . . . . . . 2
5
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 3
6
Pinning information . . . . . . . . . . . . . . . . . . . . . . 4
6.1
Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
6.2
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 4
7
Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 6
8
Thermal characteristics . . . . . . . . . . . . . . . . . . 6
9
Static characteristics. . . . . . . . . . . . . . . . . . . . . 7
10
Dynamic characteristics . . . . . . . . . . . . . . . . . 10
10.1
Dynamic characteristics . . . . . . . . . . . . . . . . . 10
10.2
Clock and digital output timing . . . . . . . . . . . . 11
10.3
Serial output timing . . . . . . . . . . . . . . . . . . . . . 12
10.4
SPI timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
11
Application information. . . . . . . . . . . . . . . . . . 14
11.1
Analog inputs . . . . . . . . . . . . . . . . . . . . . . . . . 14
11.1.1
Input stage description . . . . . . . . . . . . . . . . . . 14
11.1.2
Anti-kickback circuitry . . . . . . . . . . . . . . . . . . . 14
11.1.3
Transformer . . . . . . . . . . . . . . . . . . . . . . . . . . 15
11.2
System reference and power management . . 16
11.2.1
Internal/external reference . . . . . . . . . . . . . . . 16
11.2.2
Programmable full-scale . . . . . . . . . . . . . . . . . 18
11.2.3
Common-mode output voltage (VO(cm)) . . . . . 19
11.2.4
Biasing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
11.3
Clock input . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
11.3.1
Drive modes . . . . . . . . . . . . . . . . . . . . . . . . . . 19
11.3.2
Equivalent input circuit . . . . . . . . . . . . . . . . . . 20
11.3.3
Clock input divider . . . . . . . . . . . . . . . . . . . . . 21
11.3.4
Duty cycle stabilizer . . . . . . . . . . . . . . . . . . . . 21
11.4
Digital outputs . . . . . . . . . . . . . . . . . . . . . . . . . 21
11.4.1
Serial output equivalent circuit . . . . . . . . . . . . 21
11.5
JESD204A serializer. . . . . . . . . . . . . . . . . . . . 22
11.5.1
Digital JESD204A formatter . . . . . . . . . . . . . . 22
11.5.2
ADC core output codes versus input voltage . 23
11.6
Serial Peripheral Interface (SPI) . . . . . . . . . . . 24
11.6.1
Register description . . . . . . . . . . . . . . . . . . . . 24
11.6.2
Channel control . . . . . . . . . . . . . . . . . . . . . . . 25
11.6.3
Register description . . . . . . . . . . . . . . . . . . . . 28
11.6.3.1 ADC control registers . . . . . . . . . . . . . . . . . . . 28
11.6.4
JESD204A digital control registers . . . . . . . . . 30
12
Package outline . . . . . . . . . . . . . . . . . . . . . . . . 38
13
Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 39
14
Revision history . . . . . . . . . . . . . . . . . . . . . . . . 40
15
15.1
15.2
15.3
15.4
16
17
Legal information . . . . . . . . . . . . . . . . . . . . . .
Data sheet status . . . . . . . . . . . . . . . . . . . . . .
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . .
Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . .
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . .
Contact information . . . . . . . . . . . . . . . . . . . .
Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
41
41
41
41
42
42
43
Please be aware that important notices concerning this document and the product(s)
described herein, have been included in section ‘Legal information’.
© NXP B.V. 2011.
All rights reserved.
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: [email protected]
Date of release: 9 February 2011
Document identifier: ADC1613D_SER
Similar pages