AZETTLER AZ2500P2-1A-24D 60 amp latching power relay Datasheet

AZ
AZ2500
60 AMP LATCHING
POWER RELAY
FEATURES
•
•
•
•
•
•
Low cost
60 Amp switching
Heavy loads to 15000 VA
4 kV dielectric
Epoxy sealed construction available
UL, CUR file E43203
CONTACTS
GENERAL DATA
Arrangement
SPST (1 Form A)
Ratings
Resistive load:
Life Expectancy
Mechanical
Electrical
Minimum operations
1 x 106
1 x 105 at 40 A 250 VAC Res.
Max. switched power: 15000 VA
Max. switched current: 60 A
Max. switched voltage: 400 VAC
Set and Reset
Pulse Duration
50 ms minimum
60 A at 250 VAC, 6k cycles, General Use
50 A at 250 VAC, 10k cycles, General Use
40 A at 250 VAC, 100k cycles, General Use
Set Time (typical)
20 ms at nominal coil voltage
Reset Time (typical)
20 ms at nominal coil voltage
Material
Silver cadmium oxide or silver tin oxide
Dielectric Strength
4000 Vrms coil to contact
(at sea level for 1 min.) 1500 Vrms between open contacts
Resistance
< 50 milliohms initially
(24 V, 1 A voltage drop method)
Rated Load
UL, CUR
COIL
Insulation
Resistance
1000 megohms min. at 20°C, 500 VDC,
50% RH
Creepage Distance
8 mm
Ambient Temperature
Operating
Storage
At nominal coil voltage
-40°C (-40°F) to 70°C (158°F)
-40°C (-40°F) to 105°C (221°F)
Vibration
0.062" DA at 10–55 Hz
Power
At Pickup Voltage
(typical)
Temperature
666 mW single coil
1.3 W dual coil
Shock
Operating
20 g, 11 ms, 1/2 sine (no false operation)
Non-Operating 100 g, 11 ms, 1/2 sine (no damage)
Max. 105°C (221°F)
NOTES
1. All values at 20°C (68°F).
2. Relay may pull in with less than “Must Operate” value.
Enclosure
P.B.T. polyester
Terminals
Tinned copper alloy
P. C. (coil), heavy tabs (power)
Max. Solder Temp.
270°C (518°F)
Max. Solder Time
5 seconds
Weight
33 grams
3. Specifications subject to change without notice.
4. Allow suitable slack on leads when wiring, and do not subject the
terminals to excessive force.
10/26/06W
AZ
AZ2500
RELAY ORDERING DATA
COIL SPECIFICATIONS -Standard Single Coil - Termination Style 1
ORDER NUMBER*
Nominal Coil
Must Operate
Max. Continuous
Coil Resistance
VDC
VDC
VDC [1]
± 10%
5
4.0
6.5
24
6
4.8
7.8
35
9
7.2
11.7
80
12
9.6
15.6
145
24
19.2
31.2
575
48
38.4
62.4
2270
* Add suffix “K” for Coil Termination Style 2. For silver tin oxide contacts change “1A” to “1AE.”
Unsealed
AZ2500P1–1A–5D
AZ2500P1–1A–6D
AZ2500P1–1A–9D
AZ2500P1–1A–12D
AZ2500P1–1A–24D
AZ2500P1–1A–48D
COIL SPECIFICATIONS -Standard Dual Coil
Sealed
AZ2500P1–-1A–5DE
AZ2500P1–-1A–6DE
AZ2500P1–-1A–9DE
AZ2500P1–-1A–12DE
AZ2500P1–-1A–24DE
AZ2500P1–-1A–48DE
ORDER NUMBER*
Nominal Coil
Must Operate
Max. Continuous
Coil Resistance
Unsealed
VDC
VDC
VDC [1]
± 10%
5
4.0
6.5
12
AZ2500P2–1A–5D
6
4.8
7.8
17.5
AZ2500P2–1A–6D
9
7.2
11.7
40
AZ2500P2–1A–9D
12
9.6
15.6
72
AZ2500P2–1A–12D
24
19.2
31.2
285
AZ2500P2–1A–24D
48
38.4
62.4
1135
AZ2500P2–1A–48D
NOTE: Relays may be ordered with twisted copper wire terminations (Styles A-K) as shown below. Contact factory for ordering
[1] max. continuous voltage should not be applied for more than 30 seconds.
* For silver tin oxide contacts change “1A” to “1AE.”
Sealed
AZ2500P2–-1A–5DE
AZ2500P2–-1A–6DE
AZ2500P2–-1A–9DE
AZ2500P2–-1A–12DE
AZ2500P2–-1A–24DE
AZ2500P2–-1A–48DE
information.
MECHANICAL DATA
Outline Dimensions
PC Board Layout
.751
[19.08]
1.51 MAX
[38.25]
1.000
[25.4]
.850
[21.59]
.751
[19.08]
.751
[19.08]
3-Ø.047
[Ø1.20]
1.000
[25.4]
1.000
[25.4]
.850
[21.59]
3-Ø.047
[Ø1.20]
.115
[2.93]
1.20 MAX
[30.25]
.200
[5.08]
.105
[2.67]
AZ2500P1-Style 1
.200
[5.08]
.105
[2.67]
.105
[2.67]
AZ2500P2
AZ2500P1-Style 2
(Bottom View)
.031
.346
[8.80]
4-Ø.047
[Ø1.20]
.115
[2.93]
.115
[2.93]
.315
.039
Wiring Diagram
2x
Ø.138
[Ø3.50]
.364MAX .640MAX
[16.25]
[9.25]
+
-
Set coil
(Contact close)
.142
[3.60]
Reset polarity
Set polarity
Set polarity
0.025X0.025
[0.64X0.64]
-
+
+
-
-
+
Reset polarity
AZ2500P1-Style 1
AZ2500P1-Style 2
+
Reset coil
(Contact open)
-
+
AZ2500P2
Dimensions in inches with metric equivalents in parentheses. Tolerance: ± .010"
10/26/06W
AZ
AZ2500
Weld style of twisted copper wire (A to K)
A
F
C
B
G
H
K
D
E
Notes: Weld figures for AZ2500
with twisted copper wire. Please
show welding style (A to K) and
the length of wires when ordering.
Please note the length of each
wire from left to right if the length
is different.
10/26/06W
Similar pages