1.6x0.8x0.5mm BI-COLOR SURFACE MOUNT LED Part Number: APHB1608ZGKSYKC ATTENTION Green Super Bright Yellow OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Features Descriptions z 1.6mmX0.8mm SMT LED, 0.5mm thickness. z The Green source color devices are made with InGaN z Compatible with reflow soldering. z Available in various color combination. on Sapphire Light Emitting Diode. z The Super Bright Yellow device is made with AlGaInP (on GaAs substrate) light emitting diode chip. z Package: 2000pcs / reel . z Moisture sensitivity level : level 3. z Tinned pads for improved solderability. z Electrostatic discharge and power surge could damage the LEDs. z It is recommended to use a wrist band or anti- z RoHS compliant. electrostatic glove when handling the LEDs. z All devices, equipments and machineries must be electrically grounded. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.15(0.006") unless otherwise noted. 3.The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4.The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAO1005 REV NO: V.1B DATE: JAN/06/2015 PAGE: 1 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203014093 Selection Guide Part No. Dice Green (InGaN) APHB1608ZGKSYKC Viewing Angle [1] Iv (mcd) [2] @ 20mA Lens Type Min. Typ. 200 350 80 150 Water Clear Super Bright Yellow (AlGaInP) 2θ1/2 130° Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity/ luminous Flux: +/-15%. 3. Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Typ. λpeak Peak Wavelength Green Super Bright Yellow λD [1] Dominant Wavelength Δλ1/2 Max. Units Test Conditions 515 590 nm IF=20mA Green Super Bright Yellow 525 590 nm IF=20mA Spectral Line Half-width Green Super Bright Yellow 35 20 nm IF=20mA C Capacitance Green Super Bright Yellow 45 20 pF VF=0V;f=1MHz VF [2] Forward Voltage Green Super Bright Yellow 3.3 2 4.1 2.5 V IF=20mA IR Reverse Current Green Super Bright Yellow 50 10 uA VR = 5V Notes: 1.Wavelength: +/-1nm. 2.Forward Voltage: +/-0.1V. 3.Wavelength value is traceable to the CIE127-2007 compliant national standards. 4.Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25°C Parameter Green Super Bright Yellow Units Power dissipation 102.5 75 mW DC Forward Current 25 30 mA Peak Forward Current [1] 150 175 mA Reverse Voltage 5 Operating Temperature -40°C To +85°C Storage Temperature -40°C To +85°C V Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAO1005 REV NO: V.1B DATE: JAN/06/2015 PAGE: 2 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203014093 APHB1608ZGKSYKC Green SPEC NO: DSAO1005 REV NO: V.1B DATE: JAN/06/2015 PAGE: 3 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203014093 Super Bright Yellow SPEC NO: DSAO1005 REV NO: V.1B DATE: JAN/06/2015 PAGE: 4 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203014093 APHB1608ZGKSYKC Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Reel Dimension Tape Dimensions (Units : mm) SPEC NO: DSAO1005 REV NO: V.1B DATE: JAN/06/2015 PAGE: 5 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203014093 PACKING & LABEL SPECIFICATIONS APHB1608ZGKSYKC Terms and conditions for the usage of this document 1.The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2.The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3.When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4.The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5.The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6.All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAO1005 REV NO: V.1B DATE: JAN/06/2015 PAGE: 6 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203014093