TDK ACH32C-104-T001 3-terminal filters for power line ach sery Datasheet

E M C
C o m p o n e n t s
July 2013
3-terminal Filters
For power line
ACH series
ACH32C
ACH3218
[1206 inch]*
[1207 inch]
* Dimensions Code JIS[EIA]
(2/9)
E M C
C o m p o n e n t s
REMINDERS FOR USING THESE PRODUCTS
Before using these products, be sure to request the delivery specifications.
SAFETY REMINDERS
Please pay sufficient attention to the warnings for safe designing when using these products.
REMINDERS
The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH
or less).
If the storage period elapses, the soldering of the terminal electrodes may deteriorate.
Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.).
Before soldering, be sure to preheat components.
The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature
does not exceed 150°C.
Soldering corrections after mounting should be within the range of the conditions determined in the specifications.
If overheated, a short circuit, performance deterioration, or lifespan shortening may occur.
When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to
the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions.
Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal
design.
Carefully lay out the coil for the circuit board design of the non-magnetic shield type.
A malfunction may occur due to magnetic interference.
Use a wrist band to discharge static electricity in your body through the grounding wire.
Do not expose the products to magnets or magnetic fields.
Do not use for a purpose outside of the contents regulated in the delivery specifications.
The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications
equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement
equipment, industrial robots) under a normal operation and use condition.
The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or
quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to
society, person or property.
If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions
set forth in the each catalog, please contact us.
(1) Aerospace/Aviation equipment
(2) Transportation equipment (cars, electric trains, ships, etc.)
(3) Medical equipment
(4) Power-generation control equipment
(5) Atomic energy-related equipment
(6) Seabed equipment
(7) Transportation control equipment
(8) Public information-processing equipment
(9) Military equipment
(10) Electric heating apparatus, burning equipment
(11) Disaster prevention/crime prevention equipment
(12) Safety equipment
(13) Other applications that are not considered general-purpose
applications
When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing
protection circuit/device or providing backup circuits in your equipment.
001-01 / 20130722 / e9611_ach.fm
(3/9)
E M C
C o m p o n e n t s
3-terminal Filters
Product compatible with RoHS directive
Halogen-free
Compatible with lead-free solders
For power line
Overview of the ACH Series
FEATURES
T-type EMC filter that can be used for high-current circuits.
Achieve excellent attenuation characteristics by using it for circuits with stable grounds.
Does not require mounting space due to vertical mounting design, making it perfect for high-density circuits.
Guaranteed temperature range is –40 to +125°C, so it can be used under severe environmental conditions.
Use this product under reflow soldering conditions.
APPLICATION
HE devices (TVs, VTRs, CD players, electronic musical instruments, PCs, etc.)
OA equipment (Computers, terminals, facsimiles, etc.)
FA equipment (Robots, NC machine tools, process controllers, etc.)
AE equipment (Car navigation systems, ECUs, etc.) ACH32C cannot be used for ECUs.
PART NUMBER CONSTRUCTION
ACH32C
ACH
Series name
32C
-
L×W×T Dimensions
(mm)
32C
3.2×1.6×2.1
103
-
Capacitance
(pF)
100
10
103
10000
T
001
Packaging style
Internal code
T
Taping
ACH3218
ACH
Series name
3218
-
L×W×T Dimensions
(mm)
3218
3.2×1.8×2.5
223
-
Capacitance
(pF)
223
22000
T
□□□
Packaging style
Internal code
T
Taping
OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT
Temperature range
Operating
Storage
temperature
temperature
(°C)
(°C)
ACH32C
–40 to +125
–40 to +125
ACH3218
–40 to +125
–40 to +125
The Storage temperature range is for after the circuit board is mounted.
Type
Package quantity
Individual weight
(pieces/reel)
2,000
1,000
(mg)
70
70
RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://www.tdk.co.jp/rohs/
Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm.
• All specifications are subject to change without notice.
001-01 / 20130722 / e9611_ach.fm
(4/9)
E M C
C o m p o n e n t s
Overview of the ACH Series
RECOMMENDED REFLOW PROFILE
Preheating
Soldering
Natural
cooling
Peak
T: Temperature
T4
T3
T2
T3
t3
T1
t1
t2
t: Time
Preheating
Temp.
T1
T2
150°C
180°C
Time
t1
60 to 120s
Soldering
Temp.
Time
T3
t2
230°C
30 to 60s
Peak
Temp.
T4
250 to 260°C
Time
t3
10s max.
• All specifications are subject to change without notice.
001-01 / 20130722 / e9611_ach.fm
(5/9)
E M C
C o m p o n e n t s
ACH series
ACH32C Type
SHAPE & DIMENSIONS
2.1±0.2
1.6±0.2
3.2 ± 0.2
1
3
0.1
2
Dimensions in mm
RECOMMENDED LAND PATTERN
CIRCUIT DIAGRAM
4.2
0.6
1.0
3
1
GND
2
0.5
2.6
1.0
• No polarity
Dimensions in mm
• All specifications are subject to change without notice.
001-01 / 20130722 / e9611_ach.fm
(6/9)
E M C
C o m p o n e n t s
ACH series ACH32C Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
Rated voltage
(V)max.
Rated current
(A)max.
Insulation resistance
(M: )min.
DC resistance
(m: )max.
50
50
50
50
50
50
50
50
50
50
6
6
6
6
6
6
6
6
6
6
100
100
100
100
100
100
100
100
100
100
2
2
2
2
2
2
2
2
2
2
○ Measurement equipment
Measurement item
Product No.
Insertion loss
E5071B
DC resistance
4338A
Insulation resistance
4339A
* Equivalent measurement equipment may be used.
Guaranteed
insertion loss
(dB)
–15
–15
–15
–20
–20
–25
–25
–25
–25
–25
Guaranteed frequency
Part No.
bandwidth
(MHz)
2000 to 6000
ACH32C-100-T001
1300 to 2500
ACH32C-220-T001
650 to 2500
ACH32C-470-T001
450 to 1300
ACH32C-101-T001
200 to 800
ACH32C-331-T001
100 to 350
ACH32C-102-T001
55 to 300
ACH32C-222-T001
30 to 200
ACH32C-103-T001
10 to 300
ACH32C-333-T001
3.5 to 200
ACH32C-104-T001
Manufacturer
Agilent Technologies
Agilent Technologies
Agilent Technologies
INSERTION LOSS VS. FREQUENCY CHARACTERISTICS
0
10
Insertion loss (dB)
20
30
220
100
470
101
40
331
50
102
104
60
103
222
333
70
80
1
10
100
Frequency (MHz)
1000
10000
○ Measurement equipment
Product No.
Manufacturer
E5071B
Agilent Technologies
* Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20130722 / e9611_ach.fm
(7/9)
E M C
C o m p o n e n t s
ACH series
ACH3218 Type
SHAPE & DIMENSIONS
2.5± 0.25
3.2± 0.3
0.45
1.8± 0.2
0.6
Dimensions in mm
RECOMMENDED LAND PATTERN
CIRCUIT DIAGRAM
3
1.94
1
GND
2
• No polarity
1.4
0.6
2.2
1.4
Dimensions in mm
• All specifications are subject to change without notice.
001-01 / 20130722 / e9611_ach.fm
(8/9)
E M C
C o m p o n e n t s
ACH series ACH3218 Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
Insertion loss 25dB
frequency range
(MHz)
11 to 55
17 to 60
22 to 75
30 to 85
37 to 90
45 to 105
60 to 115
80 to 140
95 to 150
120 to 180
130 to 210
170 to 250
205 to 280
265 to 340
340 to 420
420 to 500
500 to 600
600 to 700
Rated voltage
(V)max.
Rated current
(A)max.
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
DC resistance
(: )max.
[Terminal No.1 to 3]
0.06
0.06
0.06
0.06
0.06
0.06
0.06
0.06
0.06
0.06
0.06
0.06
0.06
0.06
0.06
0.06
0.06
0.06
Insulation resistance
(M: )min.
[Terminal No.1 to 2/No.2 to 3]
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
Part No.
ACH3218-223-T□□□
ACH3218-103-T□□□
ACH3218-682-T□□□
ACH3218-472-T□□□
ACH3218-332-T□□□
ACH3218-222-T□□□
ACH3218-152-T□□□
ACH3218-102-T□□□
ACH3218-681-T□□□
ACH3218-471-T□□□
ACH3218-331-T□□□
ACH3218-221-T□□□
ACH3218-151-T□□□
ACH3218-101-T□□□
ACH3218-680-T□□□
ACH3218-470-T□□□
ACH3218-330-T□□□
ACH3218-220-T□□□
INSERTION LOSS VS. FREQUENCY CHARACTERISTICS
0
Insertion loss (dB)
10
332
20
102
222
30
330 220
40
152
223
50
470
680
1
3
10
103
221 151 101
471 331
472 682
30
Frequency (MHz)
681
100
300
1000
• All specifications are subject to change without notice.
001-01 / 20130722 / e9611_ach.fm
(9/9)
E M C
C o m p o n e n t s
ACH series
Packaging style
REEL DIMENSIONS
2.0±0.5
W1
W2
9±0.3
13+1.4
13.0±0.3 17.0±0.4
ø60min.
Type
ACH32C
ACH3218
1.0
ø13±0.2
W1
ø21±0.8
W2
+0
ø180 –3
Dimensions in mm
B
F
4.0±0.1
8.0±0.3
2.0±0.05
1.5 +0.1
0
1.75±0.1
TAPE DIMENSIONS
4.0±0.1
A
K
Dimensions in mm
Type
ACH32C
ACH3218
A
1.9±0.1
2.2±0.1
B
3.5±0.1
3.7±0.05
F
3.5±0.05
5.5±0.05
W
8.0±0.2
12.0±0.3
K
2.3±0.1
3.15max.
500 to 560min.
160min.
Taping
440min.
ACH32C TYPE
Drawing direction
40 to 80
Dimensions in mm
Taping
200min.
ACH3218 TYPE
Drawing direction
300min.
Dimensions in mm
• All specifications are subject to change without notice.
001-01 / 20130722 / e9611_ach.fm
Similar pages