ACDC 120960 Watts DNR120960TS Series xppower.com • Three Phase AC Input • Up to 93% Efficiency • Wide Adjustment Range • Full Power 40 º C to +60 º C • Rugged Design for Industrial Applications • Single Phase Input Operation (340575 VAC) • 3 Year Warranty Specification Input General • 340-575 VAC 3 phase (single phase operation with 75% of rated output), 480-820 VDC Input Frequency • 47-63 Hz Input Current • See tables Inrush Current • DNR120: 10.0 A, DNR240: 20.0 A, DNR480: 20.0 A, DNR960: 30.0 A, typical at 480 VAC, cold start Power Factor • 0.6 typical at 480 VAC input and nominal load, DNR960TS: 0.8 typical at 480 VAC input and nominal load Earth Leakage Current • 0.32 mA Input Protection • 3 internal fuses, DNR120TS, DNR240TS: T2.0 A, 600 VAC, DNR480TS: T3.15 A, 500 VAC, DNR960TS: T5.0 A, 500 VAC Input Voltage Output Output Voltage Output Voltage Trim Initial Set Accuracy Minimum Load Start Up Delay • • • • • Start Up Rise Time Hold Up Time • • Line Regulation Load Regulation • • Parallel Operation • Transient Response • Ripple & Noise • Overvoltage Protection • Overload Protection • Temperature Coefficient • Short Circuit Protection • See table See table ±1% No minimum load required <1 s (may increase at low temperature extremes) <150 ms 20 ms min at 480 VAC, DNR960TS: 15 ms min at 480 VAC ±1% ±1% max (±5% for units in parallel (not DNR120TS)) 2 units can be connected in parallel (not DNR120TS), total power available is 90% of the rated current of each unit, minimum load per unit 10%, use Ishare connection for DNR960TS. Redundancy module DPM10 available for load currents up to 10 A, contact sales 4% max deviation recovering to within 1% in 2 ms for 50% load change 100 mV pk-pk 20 MHz bandwidth, DNR960TS: 80 mV pk-pk 20 MHz bandwidth, (may increase at low temperature extremes) 120-145%, auto recovery 110%-140%, constant current, auto recovery ±0.03%/°C Continuous trip and restart (hiccup mode) (DNR480TS switchable hiccup mode or power limited ) Efficiency Isolation Switching Frequency Signals MTBF DIN Rail • See table • 3000 VAC Input to Output, 1500 VAC Input to Ground, 500 VAC Output to Ground • DNR120TS: 70 kHz typical, DNR240TS: 25 kHz typical, DNR480TS: 80 kHz typical, DNR960TS: 52 kHz typical • DC ON indicator LED Green, DC LOW indicator LED Red DC OK: normally open relay on 24 V models • DNR120TS: 550 kHrs, 240TS: 500 kHrs 480TS: 420 kHrs, 960TS: 380 kHrs to Bellcore Issue 6, at +40 °C, GB • Compatible with TS35/7.5 or TS35/15 Environmental Operating Temperature • -40 °C to 70 °C (DNR480TS -30 °C), derate linearly from 60 °C at 2.5%/°C (3.5%/°C for DNR960TS), start up at -35 °C (DNR480TS -20 °C) see derating curves Cooling • Convection-cooled with 25 mm free space all sides Operating Humidity • 20-95% RH, non-condensing Storage Temperature • -40 °C to +85 °C Shock • 15 g, 11 ms, 3 axis, 6 faces, 3 shocks/face Vibration • 2 g, 10 Hz to 500 Hz, along X, Y & Z axis, 60 min/axis, mounted on rail EMC & Safety Emissions Harmonic Currents Voltage Flicker ESD Immunity Radiated Immunity EFT/Burst Surge • • • • • • • Conducted Immunity Magnetic Field Dips & Interruptions • • • Safety Approvals • EN55022, Class B conducted & radiated EN61000-3-2, Class A EN61000-3-3 EN61000-4-2, level 4 Perf Criteria A EN61000-4-3, level 3 Perf Criteria A EN61000-4-4, level 4 Perf Criteria A EN61000-4-5, installation class 4, Perf Criteria A EN61000-4-6, level 3 perf criteria A EN61000-4-8, level 4 perf criteria A EN61000-4-11, 30% 500 ms, 60% 200 ms, >95% 5000 ms Perf Criteria A, A, A EN60950-1 UL508 UL60950-1 Pollution Degree 2, UL60950-1 Overvoltage Category II UL508 Overvoltage Category III, ANSI/ISA 12.12.01 Class 1, Division 2, Groups A,B,C and D Output Voltage 12 24 24 48 24 48 24 48 V V V V V V V V Input Current (typ.) 400 VAC 500 VAC 0.36 A 0.30 A 0.36 A 0.30 A 0.65 A 0.55 A 0.65 A 0.55 A 1.10 A 0.93 A 1.10 A 0.93 A 1.72 A 1.50 A 1.72 A 1.50 A Output Voltage Trim 11.4-14.5 22.5-28.5 22.5-28.5 47.0-56.0 22.5-28.5 47.0-56.0 22.5-28.5 47.0-56.0 Output Current(1) V V V V V V V V 10.0 5.0 10.0 5.0 20.0 10.0 40.0 20.0 Efficiency (typ.) Model Number 87% 89% 90% 91% 90% 91% 92% 93% DNR120TS12 DNR120TS24 DNR240TS24-I DNR240TS48-I DNR480TS24-I DNR480TS48-I DNR960TS24-I DNR960TS48-I A A A A A A A A ACDC DNR120960TS Models and Ratings Notes 1. Reduce by 25% for single phase input operation, (340-575 VAC). V Mechanical Details 5.91 (150.0) DC Output 4.39 (111.3) Voltage Trim 6 0.3 (7.0) 1 DC DC + + - OK OK DC LO ON DNR120TS DNR240TS 4.87 (123.6) DC LO ON All Units Voltage Trim L2 L3 1 L1 4 L2 L3 1 L1 + + - - 5 1 6 4 4 AC Input AC Input 2.93 (74.3) DC Output AC Input Parallel Single L1 4.87 (123.6) DNR480TS 4.87 Voltage (123.6) Trim L2 L3 1 DC Output DC OK 4 5 DC DC LO ON 6 +V +V-V -V 4 1 Voltage Adj. Single/parallel & current limit selector switches on underside 3.50 (89.0) DC OK signal connector on underside, Spring type, AWG26-20/0.2-0.5 mm2 10.86 (275.7) Pin 4.96 (125.9) DNR960TS DC Output +V +V -V -V AC Input L1 1 L L2 L3 DC DC LO ON 4 DC DC OK OK +Is -Is 1 8 Pin Connections - AC Input Pin Designation 1 Ground 2 L1 3 L2 4 L3 1 2 3 4 5 6 7 8 Pin Connections - DC Output DNR120 DNR240-480 DNR960TS Designation Designation Designation -V -V DC OK* -V -V DC OK* +V +V +Ishare(8) +V +V -Ishare(8) DC OK* DC OK* +V DC OK* DC OK* +V -V -V * Available on 24 V versions only Voltage trim on underside Notes 1. All dimensions in inches (mm). 2. Tolerance: ±0.02 (0.5) maximum. 3. Weight - DNR120TS: 1.76 lb (800 g) approx. DNR240TS: 2.43 lb (1100 g) approx. DNR480TS: 4.23 lb (1720 g) approx. DNR960TS: 7.05 lb (3200 g) approx. 4. Screw terminal: 10-24 AWG cable size. 5. DC OK Relay rated at 60 VDC at 300 mA. 6. Allow 0.98” (25 mm) clearance all round to ensure adequate ventilation. 7. Connection screw maximum torque: Input: 9 lbs-in (1.0 Nm), Output: 5.5 lbs-in (0.6 Nm). 8. Connecting +Ishare and -Ishare between two power supplies will force the units to current share. Derating Curves 100 Load (%) A 75 65 C B A DNR120-240TS B DNR960TS C DNR480TS 0 -40 -30 Ambient Temp (˚C) 60 70 11-May-11