Seoul FCW100Z Flash led device Datasheet

Technical Data Sheet
Pb Free
Specification
SSC-FCW100Z
(Rev 1.7, General)
SSC
Drawn
Approval
Customer
Approval
SSCSSC-FCW100Z
Revision 1.7
www.ZLED.com
서식번호 : SSC-QP-7-07-24 (Rev.0.0)
Technical Data Sheet
[ Contents ]
1.
Absolute maximum ratings
2.
Electro-optical characteristics
3.
CIE chromaticity diagram
4.
Characteristic diagram
5.
Soldering profile
6.
Outline dimension
7.
Recommended soldering pad design
8.
Reel packing dimension
9.
Packing
10. Precaution for use
SSCSSC-FCW100Z
Revision 1.7
www.ZLED.com
서식번호 : SSC-QP-7-07-24 (Rev.0.0)
Technical Data Sheet
SSC-FCW100Z
Description
• White colored SMT package
• Suitable for all SMT assembly
methods and all soldering methods
SSC-FCW100Z
Features
• 2.0 X 1.5 X 0.5 mm
• x, y coordination
x: 0.31, Y 0.31
Applications
• Cellular phone’s
Flash lighting
• Other decoration
lighting
SSCSSC-FCW100Z
Revision 1.7
www.ZLED.com
서식번호 : SSC-QP-7-07-24 (Rev.0.0)
Technical Data Sheet
1. Absolute maximum ratings
*1
(Ta=25℃)
Parameter
Symbol
Value
Unit
Power Dissipation *1
Pd
900
mW
Forward Current
IF
175
mA
Peak Forward Current *2
IFM
600
mA
Reverse Voltage
VR
5
V
LED Junction Temperature
Tj
125
℃
Rθ
10
℃/W
Operation Temperature
Topr.
-30 ~ 85
℃
Storage Temperature
Tstg.
-40 ~ 100
℃
Thermal Resistance
*3
*1. Care is to be taken that Power Dissipation does not exceed the Absolute Maximum Rating of the product.
*2. IFM conditions is Pulse width Tw≤2 sec, Duty ratio≤2/7
*3. Thermal Resistance is junction to case
2. Electro-Optical Characteristics
Parameter
Forward Voltage
Symbol
VF
(Ta=25℃)
Condition
Min
Typ
Max
IF=175 ㎃
2.7
3.0
3.7
3.2
50
㎂
cd
IF=320 ㎃
(Flash mode*2)
Reverse Current
Luminous Intensity*4
IR
IV
lx
Chromaticity
Coordination
X
Viewing Angle*7
2θ1/2
Y
V
VR=5V
-
-
IF=175 ㎃
6
9
IF=320 ㎃
-
13
-
IF=600 ㎃
-
20
-
IF=320 ㎃
-
30.5
-
[email protected]
-
13
-
lx@1m
-
0.31
-
-
0.31
-
(Flash mode*5)
(Peak current mode*6)
Illumination
Unit
(Flash mode*5)
IF=175 ㎃
IF=175㎃
130
˚
*4. The luminous intensity IV is measured at the peak of the spatial pattern which may not be aligned with the
mechanical axis of the LED package. Luminous Intensity Measurement allowance is ± 10%.
*5. Flash mode condition is Pulse width Tw = 2 sec, Duty ratio = 2/ 7.
*6. Peak current mode is pulsed width Tw ≤ 300ms, duty ratio ≤ 1/10
*7. θ 1/2 is the off-axis where the luminous intensity is 1/2 of the peak intensity.
Note : All measurements were made under the standardized environment of SSC. ( Tolerance : IV±10%, color
coordinate ±0.005, VF ±0.1 )
SSCSSC-FCW100Z
Revision 1.7
www.ZLED.com
서식번호 : SSC-QP-7-07-24 (Rev.0.0)
0.9
0.36
0.34
0.8
C
y Coord.
0.32
0.7
0.30
B
0.28
0.6
y Coord.
Technical Data Sheet
3. CIE Chromaticity Diagram
0.26
0.5
0.24
0.24
0.26
0.28
0.30
0.32
0.34
0.36
x Coord.
0.4
0.3
0.2
0.1
0.0
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
x Coord.
※ Color Rank
Rank
B
Chromaticity Coordination
X
0.247
0.292
0.272
0.317
Y
0.255
0.255
0.300
0.300
x
0.272
0.397
0.342
0.317
y
0.300
0.350
0.350
0.300
C
SSCSSC-FCW100Z
Revision 1.7
www.ZLED.com
서식번호 : SSC-QP-7-07-24 (Rev.0.0)
Relative Intensity vs Forward Current
Forward Current vs Forward Voltage
300
Ratio of Luminous Intensity (%)
Forward Current IF (mA)
1000
100
10
250
200
150
100
50
0
2.6
2.8
3.0
3.2
3.4
3.6
3.8
0
100
200
Forward Voltage VF (V)
300
400
500
600
700
800
Forward Current IF (mA)
Forward Current vs Derating Curve
Forward Current vs Chromaticity Coordinate
200
0.33
x
y
Chromatisity Coordinate x, y [a.u.]
180
160
Forward current IF(mA)
Technical Data Sheet
4. Characteristic Diagram
140
120
100
80
60
40
0.32
0.31
0.30
20
0
-2 5
0
25
50
75
o
A m b ie n t te m p e ra tu re T a ( C )
100
0.29
50
100
150
200
250
300
350
Forward Current [mA]
SSCSSC-FCW100Z
Revision 1.7
www.ZLED.com
서식번호 : SSC-QP-7-07-24 (Rev.0.0)
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
110
100
90
(Ta=25℃, IF=175mA)
80
70
120
60
130
50
140
40
30
150
160
20
170
10
180
0
Y
Y
Spectrum
o
Ta = 25 C
1.0
0.8
Intensity [a.u.]
Technical Data Sheet
Radiation Diagram
0.6
0.4
0.2
0.0
400
450
500
550
600
650
700
750
W avelength [nm ]
SSCSSC-FCW100Z
Revision 1.7
www.ZLED.com
서식번호 : SSC-QP-7-07-24 (Rev.0.0)
Reflow Soldering Conditions/ Profile
(1) Lead Solder
• Preliminary heating to be at 210℃ max. for 2 minutes max.
• Soldering heat to be at 240℃max. for 10 seconds max.
o
Device Surface Temperature [ C]
280
240
200
160
120
80
40
0
0
15
30
45
60
75
90
105
120
135
150
165
180
195
Soldering Times [sec]
(2) Lead-Free Solder
• Preliminary heating to be at 220℃max. for 2 minutes max.
• Soldering heat to be at 260℃max. for 10 seconds max.
280
o
Device Surface Temperature [ C]
Technical Data Sheet
5. Soldering profile
240
200
160
120
80
40
0
0
15
30
45
60
75
90
105 120 135 150 165 180 195
Soldering Times [sec]
(3) Hand Soldering Condition
• Not more than 3 seconds @MAX280℃, under Soldering iron.
[Note] In case the soldered products are reused in soldering process, we don’t guarantee the products.
SSCSSC-FCW100Z
Revision 1.7
www.ZLED.com
서식번호 : SSC-QP-7-07-24 (Rev.0.0)
Tolerance: ±0.05, Unit: ㎜
0.18
Resin
Anode
[SIDE VIEW]
0.50
1.20
2.00
0.50 ±0.05
1.50
[TOP VIEW]
±0.03
PCB
1.60
2.00
Technical Data Sheet
6. Outline Dimension
1.50
[BOTTOM VIEW]
Cathode
[Circuit Diagram]
7. Recommended Soldering Pad Design
[ Normal Solder pad ]
[ Solder pad for heat radiation ]
SSCSSC-FCW100Z
Revision 1.7
www.ZLED.com
서식번호 : SSC-QP-7-07-24 (Rev.0.0)
1.75±0.1
8.0±0.2
4.0±0.1
0.65±0.1
? 1.5
+0.1
-0
(2.75) 3.5±0.05
0.2±0.05
180
11.4
+0
-3
9
±0.2
+0.2
-0
2
±0.3
60
Technical Data Sheet
8. Reel Packing Dimension
22
13 ±0.2
Label
Tolerance: ±0.2, Unit: ㎜
(1) Quantity: 2,000pcs./Reel
(2) Cumulative Tolerance: Cumulative Tolerance/10pitches to be ±0.2mm
(3) Adhesion Strength of Cover Tape: Adhesion strength to be 0.1-0.7N when the over tape is
turned off from the carrier tape at10˚angle to be the carrier tape.
(4) Package: P/N, Manufacturing data Code No. and quantity to be indicated on a damp proof
Package.
SSCSSC-FCW100Z
Revision 1.7
www.ZLED.com
서식번호 : SSC-QP-7-07-24 (Rev.0.0)
Reel
#
#
#
#
#
#
#
#
#
#
:
N
/
P
##
제 품 명 : SSC-FCW 100Z
#
#
#
#
#
#
#
#
#
#
o
N
t
o
L
Technical Data Sheet
9. Packing
수 량 : 2,000
Aluminum Vinyl Bag
#
#
#
#
#
#
#
#
#
#
:
N
/
P
##
제 품 명 : SSC -FCW 100Z
#
#
#
#
#
#
#
#
#
#
o
N
t
o
L
수 량 : 2,000
Outer Box
*Material: Paper(SW3B(B))
SIZE(mm)
TYPE
a
245
7inch
c
142
b
220
c
CHIP LED
PART : SSC -FCW 100Z
C OD E :
CHIP LED
Q 'YT
b
a
: 20,000EA
LOT NO :
D ATE
:
S EO UL S EM IC ON DUCTOR C O.,L TD
SSCSSC-FCW100Z
Revision 1.7
www.ZLED.com
서식번호 : SSC-QP-7-07-24 (Rev.0.0)
Technical Data Sheet
10. Precaution for Use
(1) Storage
In order to avoid the absorption of moisture, it is recommended to store in the dry box (or
desiccator) with a desiccant. Otherwise, to store them in the following environment is
recommended.
Temperature : 5℃~30℃ Humidity : 60%HR max.
(2) Attention after opened
However LED is corresponded SMD, when LED be soldered dip, interfacial separation may
affect the light transmission efficiency, causing the light intensity to drop. Attention in followed.
a. After opened and mounted, the soldering shall be quickly.
b. Keeping of a fraction
Temperature : 5 ~ 40℃
Humidity : less than 30%
(3) In case of more than 1 week passed after opening or change color of indicator on desiccant
components shall be dried 10-12hr. at 60±5℃.
(4) In case of supposed the components is humid, shall be dried dip-solder just before.
100Hr at 80±5℃ or 12Hr at 100±5℃.
(5) Any mechanical force or any excess vibration shall not be accepted to apply during cooling
process to normal temp. after soldering.
(6) Quick cooling shall not be avoid.
(7) Components shall not be mounted on warped direction of PCB.
(8) Anti radioactive ray design is not considered for the products listed here in.
(9) Gallium arsenide is used in some of the products listed in this publication. These products are
dangerous if they are burned or smashed in the process of disposal. It is also dangerous to
drink the liquid or inhale the gas generated by such products when chemically disposed.
(10) This device should not be used in any type of fluid such as water, oil, organic solvent and etc.
When washing is required, IPA should be used.
(11) When the LEDs are illuminating, operating current should be decided after considering the
ambient maximum temperature.
(12) LEDs must be stored to maintain a clean atmosphere. If the LEDs are stored for 3 months or
more after being shipped from SSC, a sealed container with a nitrogen atmosphere should be
used for storage.
(13) The LEDs must be soldered within seven days after opening the moisture-proof packing.
(14) Repack unused products with anti-moisture packing, fold to close any opening and then
store in a dry place.
(15) The appearance and specifications of the product may be modified for improvement without
notice.
SSCSSC-FCW100Z
Revision 1.7
www.ZLED.com
서식번호 : SSC-QP-7-07-24 (Rev.0.0)
Similar pages