AD AD8592ARM-REEL Cmos single-supply, rail-to-rail input/output operational amplifiers with shutdown Datasheet

CMOS Single-Supply, Rail-to-Rail Input/Output
Operational Amplifiers with Shutdown
AD8591/AD8592/AD8594
FEATURES
PIN CONFIGURATIONS
Single-supply operation: 2.5 V to 6 V
High output current: ±250 mA
Extremely low shutdown supply current: 100 nA
Low supply current: 750 μA/Amp
Wide bandwidth: 3 MHz
Slew rate: 5 V/μs
No phase reversal
Very low input bias current
High impedance outputs when in shutdown mode
Unity-gain stable
OUT A 1
6
5 SD
TOP VIEW
(Not to Scale)
+IN A 3
4
Figure 1. 6-Lead SOT-23 (RJ Suffix)
OUT A 1
10 V+
–IN A 2
AD8592
9
+IN A 3
TOP VIEW
(Not to Scale)
8
–IN B
7
+IN B
6
SDB
Figure 2. 10-Lead MSOP (RM Suffix)
OUT A 1
16 OUT D
–IN A 2
+IN A 3
V+ 4
15 –IN D
AD8594
14 +IN D
13 V–
TOP VIEW
+IN B 5 (Not to Scale) 12 +IN C
–IN B 6
11 –IN C
OUT B 7
NC 8
9
SD
The AD8591, AD8592, and AD8594 are single, dual, and quad
rail-to-rail, input and output single-supply amplifiers featuring
250 mA output drive current and a power saving shutdown mode.
The AD8592 includes an independent shutdown function for
each amplifier. When both amplifiers are in shutdown mode,
the total supply current is reduced to less than 1 μA. The AD8591
and AD8594 include a single master shutdown function that
reduces the total supply current to less than 1 μA. All amplifier
outputs are in a high impedance state when in shutdown mode.
These amplifiers have very low input bias currents, making them
suitable for integrators and diode amplification. Outputs are stable
with virtually any capacitive load. Supply current is less than
750 μA per amplifier in active mode.
Applications for these amplifiers include audio amplification for
portable computers, portable phone headsets, sound ports, sound
cards, and set-top boxes. The AD859x family is capable of driving
heavy capacitive loads, such as LCD panel reference levels.
The ability to swing rail to rail at both the input and output enables
designers to buffer CMOS DACs, ASICs, and other wide output
swing devices in single-supply systems.
01106-003
10 OUT C
NC = NO CONNECT
GENERAL DESCRIPTION
01106-002
V– 4
OUT B
Figure 3. 16-Lead Narrow SOIC (R Suffix)
16 OUT D
OUT A 1
–IN A
15 –IN D
2
+IN A 3
AD8594
TOP VIEW
(Not to Scale)
V+ 4
14 +IN D
13 V–
+IN B
5
–IN B
6
11 –IN C
OUT B
7
10 OUT C
NC 8
12 +IN C
9
SD
NC = NO CONNECT
01106-004
Mobile communication handset audio
PC audio
PCMCIA/modem line driving
Battery-powered instrumentation
Data acquisition
ASIC input or output amplifiers
LCD display reference level drivers
–IN A
01106-001
V– 2
SDA 5
APPLICATIONS
V+
AD8591
Figure 4. 16-Lead TSSOP (RU Suffix)
The AD8591, AD8592, and AD8594 are specified over the
industrial temperature range (−40°C to +85°C). The AD8591,
single, is available in the tiny 6-lead SOT-23 package. The AD8592,
dual, is available in the 10-lead surface-mount MSOP package. The
AD8594, quad, is available in 16-lead narrow SOIC and 16-lead
TSSOP packages.
Rev. B
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2009 Analog Devices, Inc. All rights reserved.
AD8591/AD8592/AD8594
TABLE OF CONTENTS
Features .............................................................................................. 1
Output Short-Circuit Protection .............................................. 11
Applications ....................................................................................... 1
Power Dissipation....................................................................... 11
General Description ......................................................................... 1
Capacitive Loading..................................................................... 12
Pin Configurations ........................................................................... 1
PC98-Compliant Headphone/Speaker Amplifier .................. 12
Revision History ............................................................................... 2
Specifications..................................................................................... 3
A Combined Microphone and Speaker Amplifier for
Cellphone and Portable Headsets ............................................ 13
Electrical Characteristics ............................................................. 3
An Inexpensive Sample-and-Hold Circuit ............................. 13
Absolute Maximum Ratings............................................................ 5
Direct Access Arrangement for PCMCIA Modems
(Telephone Line Interface) ........................................................ 14
Thermal Resistance ...................................................................... 5
ESD Caution .................................................................................. 5
Typical Performance Characteristics ............................................. 6
Theory of Operation ...................................................................... 11
Single-Supply Differential Line Driver .................................... 14
Outline Dimensions ....................................................................... 15
Ordering Guide .......................................................................... 16
Input Voltage Protection............................................................ 11
Output Phase Reversal ............................................................... 11
REVISION HISTORY
1/09—Rev. A to Rev. B
Updated Format .................................................................. Universal
Changes to Table 1 ............................................................................ 3
Changes to Table 2 ............................................................................ 4
Deleted Spice Model for AD8591/AD8592/AD8594 Amplifiers
Sections ............................................................................................ 12
Changes to PC98-Compliant Headphone/Speaker Amplifier
Section and Figure 38 ..................................................................... 12
Changes to Figure 39 ...................................................................... 13
Changes to Figure 42 and Figure 43 ............................................. 14
Updated Outline Dimensions ....................................................... 15
Changes to Ordering Guide .......................................................... 16
Rev. B | Page 2 of 16
AD8591/AD8592/AD8594
SPECIFICATIONS
ELECTRICAL CHARACTERISTICS
VS = 2.7 V, VCM = 1.35 V, TA = 25°C, unless otherwise noted.
Table 1.
Parameter
INPUT CHARACTERISTICS
Offset Voltage
Symbol
Test Conditions
Min
Typ
VOS
−40°C < TA < +85°C
Input Bias Current
IB
5
−40°C < TA < +85°C
Input Offset Current
IOS
1
−40°C < TA < +85°C
Input Voltage Range
Common-Mode Rejection Ratio
Large Signal Voltage Gain
Offset Voltage Drift
Bias Current Drift
Offset Current Drift
OUTPUT CHARACTERISTICS
Output Voltage High
Output Voltage Low
Output Current
Open-Loop Impedance
POWER SUPPLY
Power Supply Rejection Ratio
Supply Current per Amplifier
Supply Current Shutdown Mode
SHUTDOWN INPUTS
Logic High Voltage
Logic Low Voltage
Logic Input Current
DYNAMIC PERFORMANCE
Slew Rate
Settling Time
Gain Bandwidth Product
Phase Margin
Channel Separation
NOISE PERFORMANCE
Voltage Noise Density
Current Noise Density
CMRR
AVO
ΔVOS/ΔT
ΔIB/ΔT
ΔIOS/ΔT
VCM = 0 V to 2.7 V
RL = 2 kΩ, VO = 0.3 V to 2.4 V
−40°C < TA < +85°C
−40°C < TA < +85°C
−40°C < TA < +85°C
VOH
IL = 10 mA
−40°C to +85°C
IL = 10 mA
−40°C to +85°C
VOL
IOUT
ZOUT
PSRR
ISY
0
38
2.55
2.5
25
30
50
60
25
30
2.7
mV
mV
pA
pA
pA
pA
V
dB
V/mV
μV/°C
fA/°C
fA/°C
2.61
100
125
±250
60
f = 1 MHz, AV = 1
45
ISD1
ISD2
VINH
VINL
IIN
−40°C < TA < +85°C
−40°C < TA < +85°C
−40°C < TA < +85°C
1.6
SR
tS
GBP
Φo
CS
RL = 2 kΩ
To 0.01%
en
in
Unit
45
25
20
50
20
60
VS = 2.5 V to 6 V
VO = 0 V
−40°C < TA < +85°C
All amplifiers shut down
−40°C < TA < +85°C
Amplifier 1 shut down (AD8592)
Amplifier 2 shut down (AD8592)
ISD
Max
55
0.1
V
V
mV
mV
mA
Ω
1
1.25
1
1
1.4
1.4
dB
mA
mA
μA
μA
mA
mA
0.5
1
V
V
μA
f = 1 kHz, RL = 2 kΩ
3.5
1.4
2.2
67
65
V/μs
μs
MHz
Degrees
dB
f = 1 kHz
f = 10 kHz
f = 1 kHz
45
30
0.05
nV/√Hz
nV/√Hz
pA/√Hz
Rev. B | Page 3 of 16
AD8591/AD8592/AD8594
VS = 5.0 V, VCM = 2.5 V, TA = 25°C, unless otherwise noted.
Table 2.
Parameter
INPUT CHARACTERISTICS
Offset Voltage
Symbol
Test Conditions
Min
VOS
Typ
Max
Unit
2
25
30
50
60
25
30
5
mV
mV
pA
pA
pA
pA
V
dB
V/mV
μV/°C
fA/°C
fA/°C
−40°C < TA < +85°C
Input Bias Current
IB
5
−40°C < TA < +85°C
Input Offset Current
IOS
1
−40°C < TA < +85°C
Input Voltage Range
Common-Mode Rejection Ratio
Large Signal Voltage Gain
Offset Voltage Drift
Bias Current Drift
Offset Current Drift
OUTPUT CHARACTERISTICS
Output Voltage High
Output Voltage Low
Output Current
Open-Loop Impedance
POWER SUPPLY
Power Supply Rejection Ratio
Supply Current per Amplifier
Supply Current Shutdown Mode
SHUTDOWN INPUTS
Logic High Voltage
Logic Low Voltage
Logic Input Current
DYNAMIC PERFORMANCE
Slew Rate
Full Power Bandwidth
Settling Time
Gain Bandwidth Product
Phase Margin
Channel Separation
NOISE PERFORMANCE
Voltage Noise Density
Current Noise Density
CMRR
AVO
ΔVOS/ΔT
ΔIB/ΔT
ΔIOS/ΔT
VCM = 0 V to 5 V
RL = 2 kΩ, VO = 0.5 V to 4.5 V
−40°C < TA < +85°C
−40°C < TA < +85°C
−40°C < TA < +85°C
VOH
IL = 10 mA
−40°C to +85°C
IL = 10 mA
−40°C to +85°C
VOL
IOUT
ZOUT
PSRR
ISY
0
38
15
4.9
4.85
100
125
±250
40
f = 1 MHz, AV = 1
45
ISD1
ISD2
VINH
VINL
IIN
−40°C < TA < +85°C
−40°C < TA < +85°C
−40°C < TA < +85°C
2.4
SR
BWP
tS
GBP
Φo
CS
RL = 2 kΩ
1% distortion
To 0.01%
en
in
4.94
50
VS = 2.5 V to 6 V
VO = 0 V
−40°C < TA < +85°C
All amplifiers shut down
−40°C < TA < +85°C
Amplifier 1 shut down (AD8592)
Amplifier 2 shut down (AD8592)
ISD
47
30
20
50
20
55
0.1
V
V
mV
mV
mA
Ω
1.25
1.75
1
1
1.6
1.6
dB
mA
mA
μA
μA
mA
mA
0.8
1
V
V
μA
f = 1 kHz, RL = 10 kΩ
5
325
1.6
3
70
65
V/μs
kHz
μs
MHz
Degrees
dB
f = 1 kHz
f = 10 kHz
f = 1 kHz
45
30
0.05
nV/√Hz
nV/√Hz
pA/√Hz
Rev. B | Page 4 of 16
AD8591/AD8592/AD8594
ABSOLUTE MAXIMUM RATINGS
THERMAL RESISTANCE
Table 3.
Parameter
Supply Voltage
Input Voltage
Differential Input Voltage
Output Short-Circuit Duration to GND1
Storage Temperature Range
Operating Temperature Range
Junction Temperature Range
Lead Temperature (Soldering, 60 sec)
1
Rating
6V
GND to VS
±6 V
Observe Derating Curves
−65°C to +150°C
−40°C to +85°C
−65°C to +150°C
300°C
For supplies less than ±5 V, the differential input voltage is limited to the
supplies.
θJA is specified for the worst-case conditions, that is, a device
soldered in a circuit board for surface-mount packages.
Table 4.
Package Type
6-Lead SOT-23 (RJ)
10-Lead MSOP (RM)
16-Lead SOIC (R)
16-Lead TSSOP (RU)
ESD CAUTION
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those listed in the operational sections
of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Rev. B | Page 5 of 16
θJA
230
200
120
180
θJC
92
44
36
35
Unit
°C/W
°C/W
°C/W
°C/W
AD8591/AD8592/AD8594
TYPICAL PERFORMANCE CHARACTERISTICS
0.8
100
SOURCE
10
SINK
1
0.1
1
10
100
1k
LOAD CURRENT (mA)
0.3
0.2
0.1
1.25
2.25
2.75
3.00
–2
VS = 5V
VCM = 2.5V
SINK
SOURCE
10
1
10
100
1k
LOAD CURRENT (mA)
–4
–5
–6
–7
–8
–50
01106-006
0.1
–3
–35
–15
5
25
45
65
85
01106-009
INPUT OFFSET VOLTAGE (mV)
100
1
85
TEMPERATURE (°C)
Figure 6. Output Voltage to Supply Rail vs. Load Current
Figure 9. Input Offset Voltage vs. Temperature
8
0.90
VS = 2.7V, 5V
VCM = VS/2
0.85
7
INPUT BIAS CURRENT (pA)
0.80
0.75
VS = 5V
0.70
0.65
0.60
VS = 2.7V
0.50
–40
–20
0
20
6
5
4
3
0.55
40
60
80
TEMPERATURE (°C)
100
01106-007
SUPPLY CURRENT/AMPLIFIER (mA)
1.75
Figure 8. Supply Current per Amplifier vs. Supply Voltage
1k
ΔOUTPUT VOLTAGE (mV)
0.4
SUPPLY VOLTAGE (±V)
VS = 5V
TA = 25°C
0.1
0.01
0.5
0
0.75
Figure 5. Output Voltage to Supply Rail vs. Load Current
10k
0.6
01106-010
0.1
0.01
TA = 25°C
0.7
01106-008
SUPPLY CURRENT/AMPLIFIER (mA)
VS = 2.7V
TA = 25°C
01106-005
ΔOUTPUT VOLTAGE (mV)
1k
2
–50
–35
–15
5
25
45
65
TEMPERATURE (°C)
Figure 10. Input Bias Current vs. Temperature
Figure 7. Supply Current per Amplifier vs. Temperature
Rev. B | Page 6 of 16
AD8591/AD8592/AD8594
VS = 2.7V, 5V
VCM = VS/2
60
3
INPUT OFFSET CURRENT (pA)
VS = 5V
RL = NO LOAD
TA = 25°C
45
40
90
20
135
0
180
GAIN (dB)
2
1
0
PHASE SHIFT (Degrees)
80
4
–1
–15
5
25
45
65
85
TEMPERATURE (°C)
1k
100k
1M
100M
Figure 14. Open-Loop Gain and Phase vs. Frequency
5
VS = 5V
TA = 25°C
VS = 2.7V
RL = 2kΩ
TA = 25°C
VIN = 2.5V p-p
7
4
INPUT BIAS CURRENT (pA)
10M
FREQUENCY (Hz)
Figure 11. Input Offset Current vs. Temperature
8
10k
01106-014
–35
01106-011
–2
–50
OUTPUT SWING (V p-p)
6
5
4
3
3
2
1
1
2
3
4
5
COMMON-MODE VOLTAGE (V)
0
1k
VS = 2.7V
RL = NO LOAD
TA = 25°C
60
100k
VS = 5V
RL = 2kΩ
TA = 25°C
VIN = 2.5V p-p
45
0
180
1k
10k
100k
1M
10M
100M
FREQUENCY (Hz)
OUTPUT SWING (V p-p)
135
PHASE SHIFT (Degrees)
20
3
2
1
01106-013
GAIN (dB)
4
90
10M
Figure 15. Closed-Loop Output Voltage Swing vs. Frequency
5
40
1M
FREQUENCY (Hz)
Figure 12. Input Bias Current vs. Common-Mode Voltage
80
10k
0
1k
10k
100k
1M
10M
FREQUENCY (Hz)
Figure 16. Closed-Loop Output Voltage Swing vs. Frequency
Figure 13. Open-Loop Gain and Phase vs. Frequency
Rev. B | Page 7 of 16
01106-017
0
01106-012
1
01106-016
2
AD8591/AD8592/AD8594
140
VS = 5V
TA = 25°C
AV = 10
100
80
120
60
PSRR (dB)
140
100
80
AV = 1
20
0
–20
20
–40
100k
1M
10M
100M
FREQUENCY (Hz)
–60
100
110
60
SMALL SIGNAL OVERSHOOT (%)
100
CMRR (dB)
90
80
70
100k
1M
10M
FREQUENCY (Hz)
50
SMALL SIGNAL OVERSHOOT (%)
+PSRR
40
–PSRR
0
–20
20
10
100
1k
10k
50
10k
VS = 5V
RL = 2kΩ
TA = 25°C
40
–OS
+OS
30
20
10
–40
–60
100
1k
10k
100k
1M
FREQUENCY (Hz)
10M
01106-020
PSRR (dB)
–OS
30
60
80
20
+OS
Figure 21. Small Signal Overshoot vs. Load Capacitance
100
60
10M
CAPACITANCE (pF)
VS = 2.5V
TA = 25°C
120
1M
40
Figure 18. Common-Mode Rejection Ratio vs. Frequency
140
100k
VS = 2.5V
RL = 2kΩ
TA = 25°C
0
10
01106-019
60
10k
10k
Figure 20. Power Supply Rejection Ratio vs. Frequency
VS = 5V
TA = 25°C
1k
1k
FREQUENCY (Hz)
Figure 17. Closed-Loop Output Impedance vs. Frequency
50
+PSRR
40
40
10k
–PSRR
01106-021
60
01106-018
IMPEDANCE (Ω)
160
0
1k
VS = 5V
TA = 25°C
120
01106-022
180
01106-023
200
Figure 19. Power Supply Rejection Ratio vs. Frequency
0
10
100
1k
CAPACITANCE (pF)
Figure 22. Small Signal Overshoot vs. Load Capacitance
Rev. B | Page 8 of 16
AD8591/AD8592/AD8594
VS = ±2.5V
AV = +1
RL = 2kΩ
TA = 25°C
100
20mV/DIV
90
VS = ±1.35V
VIN = ±50mV
AV = +1
RL = 2kΩ
CL = 300pF
TA = 25°C
0V
10
01106-024
500mV
500 ns/DIV
01106-027
0
500ns
Figure 26. Large Signal Transient Response
Figure 23. Small Signal Transient Response
1V
10µs
100
VS = ±2.5V
VIN = ±50mV
AV = +1
RL = 2kΩ
CL = 300pF
TA = 25°C
0V
10
0
Figure 24. Small Signal Transient Response
0
500ns
VS = 5V
TA = 25°C
0.1
0.01
10
100
1k
10k
FREQUENCY (Hz)
Figure 28. Current Noise Density vs. Frequency
Figure 25. Large Signal Transient Response
Rev. B | Page 9 of 16
100k
01106-029
10
CURRENT NOISE DENSITY (pA/√Hz)
1
90
500mV
01106-028
Figure 27. No Phase Reversal
VS = ±1.35V
AV = +1
RL = 2kΩ
TA = 25°C
100
VS = ±2.5V
AV = +1
TA = +25°C
1V
01106-025
500 ns/DIV
01106-026
20mV/DIV
90
AD8591/AD8592/AD8594
100
600
VS = 5V
AV = +1000
TA = 25°C
FREQUENCY = 1kHz
VS = 2.7V
VCM = 1.35V
TA = 25°C
500
100µV/DIV
QUANTITY (Amplifiers)
90
10
0
400
300
200
–12
–10
–8
–6
–4
–2
0
2
4
6
01106-032
0
–14
MARKER 41µV/√Hz
6
01106-033
01106-030
100
INPUT OFFSET VOLTAGE (mV)
Figure 29. Voltage Noise Density vs. Frequency
100
Figure 31. Input Offset Voltage Distribution
600
VS = 5V
AV = +1000
TA = 25°C
FREQUENCY = 10kHz
VS = 5V
VCM = 2.5V
TA = 25°C
500
200µV/DIV
QUANTITY (Amplifiers)
90
10
400
300
200
0
01106-031
100
0
–14
MARKER 25.9 µV/√Hz
–12
–10
–8
–6
–4
–2
0
2
INPUT OFFSET VOLTAGE (mV)
Figure 30. Voltage Noise Density vs. Frequency
Figure 32. Input Offset Voltage Distribution
Rev. B | Page 10 of 16
4
AD8591/AD8592/AD8594
THEORY OF OPERATION
The AD859x amplifiers are CMOS, high output drive, rail-torail input and output single-supply amplifiers designed for low
cost and high output current drive. The parts include a power
saving shutdown function that makes the AD8591/AD8592/
AD8594 op amps ideal for portable multimedia and
telecommunications applications.
OUTPUT PHASE REVERSAL
Figure 33 shows the simplified schematic for the AD8591/AD8592/
AD8594 amplifiers. Two input differential pairs, consisting of
an n-channel pair (M1, M2) and a p-channel pair (M3, M4),
provide a rail-to-rail input common-mode range. The outputs of
the input differential pairs are combined in a compound foldedcascode stage that drives the input to a second differential pair
gain stage. The outputs of the second gain stage provide the gate
voltage drive to the rail-to-rail output stage.
The rail-to-rail output stage consists of M15 and M16, which
are configured in a complementary common source configuration.
As with any rail-to-rail output amplifier, the gain of the output
stage, and thus the open-loop gain of the amplifier, is dependent
on the load resistance. In addition, the maximum output voltage
swing is directly proportional to the load current. The difference
between the maximum output voltage to the supply rails, known as
the dropout voltage, is determined by the on-channel resistance
of the AD8591/AD8592/AD8594 output transistors. The output
dropout voltage is given in Figure 5 and Figure 6.
100µA
50µA
*
M337
M5
M3
M12
M30
M4
M15
IN–
OUT
M2
M6
M9
20µA
INV
M340
*
50µA
M7
M10
V–
*ALL CURRENT SOURCES GO TO 0µA IN SHUTDOWN MODE.
(2)
+5V
*
AD8592
M13
M31
Although not shown in the simplified schematic, ESD protection
diodes are connected from each input to each power supply rail.
These diodes are normally reverse-biased, but turn on if either
input voltage exceeds either supply rail by more than 0.6 V. If this
condition occurs, limit the input current to less than ±5 mA.
This is done by placing a resistor in series with the input(s).
The minimum resistor value should be
5 mA
VSY
250 mA
VIN
INPUT VOLTAGE PROTECTION
VIN , MAX
RX ≥
M14
Figure 33. Simplified Schematic
RIN ≥
By placing a resistor in series with the output of the amplifier,
as shown in Figure 34, the output current can be limited. The
minimum value for RX is
RX
20Ω
VOUT
01106-035
VB3
To achieve high output current drive and rail-to-rail performance,
the outputs of the AD859x family do not have internal shortcircuit protection circuitry. Although these amplifiers are
designed to sink or source as much as 250 mA of output current,
shorting the output directly to the positive supply could damage or
destroy the device. To protect the output stage, limit the maximum
output current to ±250 mA.
M16
01106-034
IN+
OUTPUT SHORT-CIRCUIT PROTECTION
For a 5 V single-supply application, RX should be at least 20 Ω.
Because RX is inside the feedback loop, VOUT is not affected. The
trade-off in using RX is a slight reduction in output voltage
swing under heavy output current loads. RX also increases the
effective output impedance of the amplifier to RO + RX, where RO
is the output impedance of the device.
20µA
M8
VB2
M1
*
*
100µA
M11
INV
The technique recommended in the Input Voltage Protection
section should be applied in applications where the possibility
of input voltages exceeding the supply voltages exists.
V+
*
SD
The AD8591/AD8592/AD8594 are immune to output voltage
phase reversal with an input voltage within the supply voltages
of the device. However, if either of the inputs of the device exceeds
0.6 V outside of the supply rails, the output could exhibit phase
reversal. This is due to the ESD protection diodes becoming
forward-biased, thus causing the polarity of the input terminals
of the device to switch.
(1)
Figure 34. Output Short-Circuit Protection
POWER DISSIPATION
Although the AD859x amplifiers are able to provide load
currents of up to 250 mA, proper attention should be given to
not exceeding the maximum junction temperature for the device.
The junction temperature equation is
TJ = PDISS × θJA + TA
(3)
where:
TJ is the AD859x junction temperature.
PDISS is the AD859x power dissipation.
θJA is the AD859x junction-to-ambient thermal resistance of the
package.
TA is the ambient temperature of the circuit.
Rev. B | Page 11 of 16
AD8591/AD8592/AD8594
In any application, the absolute maximum junction temperature
must be limited to 150°C. If the junction temperature is exceeded,
the device could suffer premature failure. If the output voltage
and output current are in phase, for example, with a purely resistive
load, the power dissipated by the AD859x can be found as
PDISS = ILOAD × (VSY − VOUT)
47nF LOAD
ONLY
(4)
where:
ILOAD is the AD859x output load current.
VSY is the AD859x supply voltage.
VOUT is the output voltage.
CAPACITIVE LOADING
The AD859x exhibits excellent capacitive load driving capabilities
and can drive to 10 nF directly. Although the device is stable
with large capacitive loads, there is a decrease in amplifier
bandwidth as the capacitive load increases. Figure 35 shows
a graph of the AD8592 unity-gain bandwidth under various
capacitive loads.
4.0
VS = ±2.5V
RL = 1kΩ
TA = 25°C
3.5
3.0
50mV
10µs
01106-038
SNUBBER
IN CIRCUIT
By calculating the power dissipation of the device and using the
thermal resistance value for a given package type, the maximum
allowable ambient temperature for an application can be found
using Equation 3.
Figure 37. Snubber Network Reduces Overshoot and Ringing
Caused by Driving Heavy Capacitive Loads
The optimum values for the snubber network should be
determined empirically based on the size of the capacitive load.
Table 5 shows a few sample snubber network values for a given
load capacitance.
Table 5. Snubber Networks for Large Capacitive Loads
Snubber Network
RS (Ω)
CS (μF)
300
0.1
30
1
5
1
Load Capacitance, CL (nF)
0.47
4.7
47
PC98-COMPLIANT HEADPHONE/SPEAKER
AMPLIFIER
2.5
Because of its high output current performance and shutdown
feature, the AD8592 makes an excellent amplifier for driving an
audio output jack in a computer application. Figure 38 shows
how the AD8592 can be interfaced with an AC’97 codec to
drive headphones or speakers.
2.0
1.5
1.0
0.5
+5V
1
0.1
100
10
CAPACITIVE LOAD (nF)
AVDD2 38
Figure 35. Unity-Gain Bandwidth vs. Capacitive Load
When driving heavy capacitive loads directly from the AD859x
output, a snubber network can be used to improve the transient
response. This network consists of a series RC connected from
the output of the amplifier to ground, placing it in parallel with
the capacitive load. The configuration is shown in Figure 36.
Although this network does not increase the bandwidth of the
amplifier, it significantly reduces the amount of overshoot, as
shown in Figure 37.
LINE_OUT_L 35
U1-A
4
1
3
R4
20Ω
R2 NC
2kΩ
+5V
R1
100kΩ
AD1881A*
(AC’97)
6
LINE_OUT_R 36
7
AVSS1 26
C2
100µF
U1-B
9
8
R5
20Ω
R3
2kΩ
U1 = AD8592
RS
5Ω
CS
1µF
*ADDITIONAL PINS OMITTED FOR CLARITY.
VOUT
CL
47nF
Figure 38. PC98-Compliant Headphone/Line Out Amplifier
01106-037
AD8592
C1
100µF
10
2
5
+5V
VIN
100mV p-p
+5V
AVDD1 25
01106-036
0
0.01
Figure 36. Configuration for Snubber Network to Compensate for Capacitive Loads
Rev. B | Page 12 of 16
01106-039
BANDWIDTH (MHz)
50mV
AD8591/AD8592/AD8594
A COMBINED MICROPHONE AND SPEAKER
AMPLIFIER FOR CELLPHONE AND PORTABLE
HEADSETS
The dual amplifiers in the AD8592 make an efficient design for
interfacing with a headset containing a microphone and speaker.
Figure 40 demonstrates a simple method for constructing an
interface to a codec.
If gain is required from the output amplifier, add four additional
resistors, as shown in Figure 39. The gain of the AD8592 can
be set as
R7
R6
AVDD2 38
+5V
R7
1kΩ
U1-A
4
1
5
VREF 27
LINE_OUT_R 36
+5V
U1 = AD8592
U1-B
9
8
R5
20Ω
FROM CODEC
MONO OUT
(OR LEFT OUT)
U1-A is used as a microphone preamplifier, where the gain of
the preamplifier is set as R3/R2. R1 is used to bias an electret
microphone, and C1 blocks any dc voltages from the amplifier.
U1-B is the speaker amplifier, and its gain is set at R5/R4. To
sum a stereo output, add R6, equal in value to R4.
R3
2kΩ
R6
= 6dB WITH VALUES SHOWN
01106-040
R7
U1 = AD8592
*ADDITIONAL PINS OMITTED FOR CLARITY.
Figure 39. PC98-Compliant Headphone/Line Out Amplifier with Gain
Input coupling capacitors are not required for either circuit
because the reference voltage is supplied from the AD1881A.
R4 and R5 help protect the AD8592 output in case the output
jack or headphone wires accidentally are shorted to ground. The
output coupling capacitors, C1 and C2, block dc current from the
headphones and create a high-pass filter with a corner frequency of
=
R4
10kΩ
Figure 40. Speaker/Microphone Headset Amplifier Circuit
R7
10kΩ
− 3dB
7
(RIGHT OUT)
R6
10kΩ
(OPTIONAL)
R5
10kΩ
AVSS1 26
f
U1-B
8
R1
100kΩ
C2
100µF
AV =
6
9
6
7
5
VREF
FROM CODEC
R4
20Ω
R2 NC
2kΩ
TO
CODEC
1
R8
100kΩ
C2
10µF
C1
100µF
10
2
+5V
MICROPHONE
AND SPEAKER
JACK
3
R6
10kΩ
U1-A
3
R7
10kΩ
AD1881A*
(AC’97)
10
2
4
AVDD1 25
R6
10kΩ
+5V
R2
10kΩ
NC
(5)
+5V
LINE_OUT_L 35
C1
0.1µF
R1
2.2kΩ
1
2π C1 (R 4 + R L )
where RL is the resistance of the headphones.
(6)
Using the same principle described in the PC98-Compliant
Headphone/Speaker Amplifier section, the normalizing contact
on the microphone/speaker jack can be used to put the AD8592
into shutdown when the headset is not plugged in. The AD8592
shutdown inputs can also be controlled with TTL- or CMOScompatible logic, allowing microphone or speaker muting, if
desired.
AN INEXPENSIVE SAMPLE-AND-HOLD CIRCUIT
The independent shutdown control of each amplifier in the
AD8592 allows a degree of flexibility in circuit design. One
particular application for which this feature is useful is in
designing a sample-and-hold circuit for data acquisition. Figure 41
shows a schematic of a simple, yet extremely effective, sampleand-hold circuit using a single AD8592 and one capacitor.
8
+5V
2
10
U1-B
U1-A
VIN
3
5
4
1
C1
1nF
7
6
9
+5V
U1 = AD8592
SAMPLE
CLOCK
Figure 41. An Efficient Sample-and-Hold Circuit
Rev. B | Page 13 of 16
SAMPLE
AND HOLD
OUTPUT
01106-042
AV =
R3
100kΩ
+5V
01106-041
When headphones are plugged into the jack, the normalizing
contacts disconnect from the audio contacts. This allows the
voltage to the AD8592 shutdown pins to be pulled to 5 V,
activating the amplifiers. With no plug in the output jack, the
shutdown voltage is pulled to 100 mV through the R1 and R3 + R5
voltage divider. This powers the AD8592 down when it is not
needed, saving current from the power supply or battery.
AD8591/AD8592/AD8594
The U1-B amplifier is used as a unity-gain buffer to prevent
loading on C1. Because of the low input bias current of the U1-B
CMOS input stage and the high impedance state of the U1-A
output in shutdown, there is little voltage droop from C1 during
the hold period. This circuit can be used with sample frequencies as
high as 500 kHz and as low as 1 Hz. By increasing the C1 value,
lower voltage droop is achieved for very low sample rates.
SINGLE-SUPPLY DIFFERENTIAL LINE DRIVER
Figure 43 shows a single-supply differential line driver circuit
that can drive a 600 Ω load with less than 0.7% distortion from
20 Hz to 15 kHz with an input signal of 4 V p-p and a single 5 V
supply. The design uses an AD8594 to mimic the performance
of a fully balanced transformer-based solution. However, this
design occupies much less board space, while maintaining low
distortion, and can operate down to dc. Like the transformer-based
design, either output can be shorted to ground for unbalanced
line driver applications without changing the circuit gain of 1.
R3
10kΩ
2
3
R2
10kΩ
DIRECT ACCESS ARRANGEMENT FOR PCMCIA
MODEMS (TELEPHONE LINE INTERFACE)
P1
Tx GAIN
ADJUST
TO TELEPHONE
LINE
1:1
2kΩ
R3
360Ω
1
2
A1
9
R5
10kΩ
6.2V
C1
R1
10kΩ 0.1µF
R6
10kΩ
7
6
A2
5
TRANSMIT
TxA
R9
10kΩ
R10
10kΩ
11
R11
10kΩ
R12
10kΩ
12
9
A3
10
R14
R13
10kΩ 14.3kΩ
15
9
14
A4
P2
Rx GAIN
ADJUST
2kΩ
16
10
A1
8
10
1
9
4
R1
10kΩ
R11
10kΩ
R10
10kΩ
8
7
A2
A1
R8
100kΩ
7
4
R9
100kΩ
RL
600Ω
C2
1µF
R12
10kΩ
9
R14
50Ω
C4
47µF
VO2
R13
10kΩ
The circuit can also be configured to provide additional gain, if
desired. The gain of the circuit is
AV =
R8
10kΩ
RECEIVE
RxA
C2
0.1µF
+5V
R8 and R9 set up the common-mode output voltage equal to
half of the supply voltage. C1 is used to couple the input signal
and can be omitted if the dc voltage of the input is equal to half
of the supply voltage.
R7
10kΩ
10µF
R7
10kΩ
Figure 43. Low Noise, Single-Supply Differential Line Driver
SHUTDOWN
9
3
A1, A2 = 1/2 AD8592
GAIN = R3
R2
SET: R7, R10, R11 = R2
SET: R6, R12, R13 = R3
+5V
T1
MIDCOM
671-8005
2
VO1
+5V
VOUT R3
=
VIN
R2
where:
VOUT = VO1 − VO2
R2 = R7 = R10 = R11
R3 = R6 = R12 = R1
3
6.2V
A1, A2 = 1/4 AD8594
A3, A4 = 1/4 AD8594
VIN
01106-043
ZO
600Ω
R2
9.09kΩ
C1
22µF
C3
47µF
R6
10kΩ
+5V
Figure 42 illustrates a 5 V transmit/receive telephone line
interface for 600 Ω systems. It allows full duplex transmission
of signals on a transformer-coupled 600 Ω line in a differential
manner. Amplifier A1 provides gain that can be adjusted to
meet the modem output drive requirements. Both A1 and A2
are configured to apply the largest possible signal on a single
supply to the transformer. Because of the high output current
drive and low dropout voltages of the AD8594, the largest signal
available on a single 5 V supply is approximately 4.5 V p-p into
a 600 Ω transmission system. Amplifier A3 is configured as a
difference amplifier for two reasons. It prevents the transmit
signal from interfering with the receive signal, and it extracts
the receive signal from the transmission line for amplification
by A4. The gain of A4 can be adjusted in the same manner as
the gain of A1 to meet the input signal requirements of the
modem. Standard resistor values permit the use of single
inline package (SIP) format resistor arrays. Couple this with
the 16-lead TSSOP or SOIC footprint of the AD8594, and this
circuit offers a compact, cost-effective solution.
R5
50Ω
1
A2
01106-044
The U1-A amplifier is configured as a unity-gain buffer driving
a 1 nF capacitor. The input signal is connected to the noninverting
input, and the sample clock controls the shutdown for that
amplifier. When the sample clock is high, the U1-A amplifier is
active and the output follows VIN. When the sample clock goes
low, U1-A shuts down with the output of the amplifier going to
a high impedance state, holding the voltage on the C1 capacitor.
Figure 42. Single-Supply Direct Access Arrangement for PCMCIA Modems
Rev. B | Page 14 of 16
(7)
AD8591/AD8592/AD8594
OUTLINE DIMENSIONS
2.90 BSC
6
5
4
1
2
3
2.80 BSC
1.60 BSC
PIN 1
INDICATOR
0.95 BSC
1.90
BSC
1.30
1.15
0.90
1.45 MAX
0.50
0.30
0.15 MAX
0.22
0.08
10°
4°
0°
SEATING
PLANE
0.60
0.45
0.30
COMPLIANT TO JEDEC STANDARDS MO-178-AB
Figure 44. 6-Lead Small Outline Transistor Package [SOT-23]
(RJ-6)
Dimensions shown in millimeters
3.10
3.00
2.90
10
3.10
3.00
2.90
1
6
5
5.15
4.90
4.65
PIN 1
0.50 BSC
0.95
0.85
0.75
1.10 MAX
0.15
0.05
0.33
0.17
SEATING
PLANE
0.80
0.60
0.40
8°
0°
0.23
0.08
COPLANARITY
0.10
COMPLIANT TO JEDEC STANDARDS MO-187-BA
Figure 45. 10-Lead Mini Small Outline Package [MSOP]
(RM-10)
Dimensions shown in millimeters
10.00 (0.3937)
9.80 (0.3858)
4.00 (0.1575)
3.80 (0.1496)
9
16
1
8
1.27 (0.0500)
BSC
0.25 (0.0098)
0.10 (0.0039)
COPLANARITY
0.10
0.51 (0.0201)
0.31 (0.0122)
6.20 (0.2441)
5.80 (0.2283)
1.75 (0.0689)
1.35 (0.0531)
SEATING
PLANE
0.50 (0.0197)
0.25 (0.0098)
45°
8°
0°
0.25 (0.0098)
0.17 (0.0067)
1.27 (0.0500)
0.40 (0.0157)
Figure 46. 16-Lead Standard Small Outline Package [SOIC_N]
Narrow Body (R-16)
Dimensions shown in millimeters and (inches)
Rev. B | Page 15 of 16
060606-A
COMPLIANT TO JEDEC STANDARDS MS-012-AC
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
AD8591/AD8592/AD8594
5.10
5.00
4.90
16
9
4.50
4.40
4.30
6.40
BSC
1
8
PIN 1
1.20
MAX
0.15
0.05
0.30
0.19
0.65
BSC
COPLANARITY
0.10
0.20
0.09
SEATING
PLANE
0.75
0.60
0.45
8°
0°
COMPLIANT TO JEDEC STANDARDS MO-153-AB
Figure 47. 16-Lead Thin Shrink Small Outline Package [TSSOP]
(RU-16)
Dimensions shown in millimeters
ORDERING GUIDE
Model
AD8591ART-REEL
AD8591ART-REEL7
AD8591ARTZ-REEL 1
AD8591ARTZ-REEL71
AD8592ARM-REEL
AD8592ARMZ-REEL1
AD8594AR
AD8594AR-REEL
AD8594AR-REEL7
AD8594ARZ1
AD8594ARZ-REEL1
AD8594ARZ-REEL71
AD8594ARU-REEL
AD8594ARUZ-REEL1
1
Temperature Range
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
Package Description
6-Lead SOT-23
6-Lead SOT-23
6-Lead SOT-23
6-Lead SOT-23
10-Lead MSOP
10-Lead MSOP
16-Lead SOIC_N
16-Lead SOIC_N
16-Lead SOIC_N
16-Lead SOIC_N
16-Lead SOIC_N
16-Lead SOIC_N
16-Lead TSSOP
16-Lead TSSOP
Z = RoHS Compliant Part, # denotes RoHS compliant part may be top or bottom marked.
©2009 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D01106-0-1/09(B)
Rev. B | Page 16 of 16
Package Option
RJ-6
RJ-6
RJ-6
RJ-6
RM-10
RM-10
R-16
R-16
R-16
R-16
R-16
R-16
RU-16
RU-16
Branding
A9A
A9A
A9A#
A9A#
AQA
AQA#
Similar pages