DC-DC Converter UNIT CER Series (1.5 W REGULATED DC-DC CONVERTER) FEATURES z 1000VDC ISOLATION HIGH EFFICIENCY SIX-SIDED SHIELD TO REDUCE EMI LOW COST NO EXTERNAL COMPONENTS REQUIRED UP TO 1.5W REGULATED OUTPUT POWER DUAL IN LINE PACKAGE z z z 100% BURNED IN LOW NOISE MTBF > 850,000 HOURS z OUTPUT SPECIFICATIONS z z z z z z z Voltage Setpoint Accuracy +/-2% max Temperature Coefficient +/-0.03%/ C O Ripple & Noise (20MHz INPUT SPECIFICATIONS Input Voltage Range +/-10% max Input Filter Pi Network 100mVp-p max BW) Line Regulation1 Load Regulation +/-0.5% max 2 +/-0.5% max Short Circuit Protection Current Limit z GENERAL SPECIFICATIONS Efficiency 58% min Protection Short Circuit Restart z Automatic ENVIRONMENTAL SPECIFICATIONS Operating Temperature Isolation Resistance -25 C to +71 C O Storage Temperature O -55 C to +125 C O Isolation Voltage3 O Switching Frequency Isolation 1000 VDC min 9 10 ohms min 50 KHz min 80pF max Capacitance Cooling Free-Air Convection MTBF Weight ALL SPECIFICATIONS TYPICAL AT NOMINAL Case Material LINE, Case Size FULL LOAD , AND 25 O C UNLESS 850,000 Hours 12.0g-14.4g Six-Sided Shield Case 31.8mm*20.3mm*10.2mm OTHERWISE NOTED. 1 High Line to Low Line. 2 Load Regulation is for output load current change from 10% to 100%. 3 For 60 seconds www.Power-Systems.de Page: 1 / 5 Version: 4-Oct-02 DC-DC Converter UNIT CER Series (1.5 W REGULATED DC-DC CONVERTER) z SELECTION GUIDE 1.5W OUTPUT MODEL NUMBER INPUT OUTPUT OUTPUT VOLTAGE VOLTAGE CURRENT (VDC) (VDC) (mA) INPUT CURRENT(mA) EFF ISOLATION FULL NO (%) (VDC) LOAD LOAD CERS-0505M 4.5-5.5 5 300 500 40 60 1000 CERS-0512M 4.5-5.5 12 125 490 40 61 1000 CERS-0515M 4.5-5.5 15 100 490 40 61 1000 CERD-0512M 4.5-5.5 +/-12 +/-63 490 40 61 1000 CERD-0515M 4.5-5.5 +/-15 +/-50 490 40 61 1000 CERS-1205M 10.8-13.2 5 300 205 15 61 1000 CERS-1212M 10.8-13.2 12 125 195 15 64 1000 CERS-1215M 10.8-13.2 15 100 195 15 64 1000 CERD-1212M 10.8-13.2 +/-12 +/-63 195 15 64 1000 CERD-1215M 10.8-13.2 +/-15 +/-50 190 15 66 1000 CERS-2405M 21.6-26.4 5 300 100 10 63 1000 CERS-2412M 21.6-26.4 12 125 95 10 66 1000 CERS-2415M 21.6-26.4 15 100 95 10 66 1000 CERD-2412M 21.6-26.4 +/-12 +/-63 95 10 66 1000 CERD-2415M 21.6-26.4 +/-15 +/-50 93 10 67 1000 Note: Other input to output voltages may be available. Please contact factory. www.Power-Systems.de Page: 2 / 5 Version: 4-Oct-02 DC-DC Converter UNIT CER Series (1.5 W REGULATED DC-DC CONVERTER) z SIMPLIFIED SCHEMATIC SINGLE OUTPUT +Vin REGULATOR DUAL OUTPUT +Vout OSCILLATOR DRIVER -Vin REGULATOR +Vin OSCILLATOR DRIVER -Vout +Vout Com. -Vout -Vin REGULATOR z MECHANICAL DIMENSIONS & RECOMMENDED FOOTPRINT DETAILS www.Power-Systems.de Page: 3 / 5 PIN SINGLE DUAL 1 & 24 +Vin +Vin 2 & 23 NC -Vout 3 & 22 NC Common 10 & 15 -Vout Common 11 & 14 +Vout +Vout 12 & 13 -Vin -Vin Version: 4-Oct-02 DC-DC Converter UNIT CER Series (1.5 W REGULATED DC-DC CONVERTER) z TYPICAL APPLICATIONS SINGLE OUTPUT INPUT DUAL OUTPUT OUTPUT INPUT OUTPUT +Vout +Vin +Vin +Vout LOAD1 LOAD DC-DC CONVERTER -Vin Common DC-DC CONVERTER -Vin -Vout LOAD2 -Vout z TYPICAL PERFORMANCE CUREVES Specifications typical at ta=25 OC,nominal input voltage , rated output current unless otherwise specified. OUTPUT LOAD vs EFFICIENCY OUTPUT LOAD vs OUTPUT VOLTAGE OUTPUT VOLTAGE CHANGE(%) EFFICIENCY(%) 80% 60% SAFE OPERATING AREA 40% 20% 0% 0% 20% 40% 60% 80% 10% 5% 0% -5% -10% 100% 0% OUTPUT LOAD(%) 40% 60% 80% 100% OUTPUT LOAD(%) TEMPERATURE DERATING INPUT VOLTAGE vs EFFICIENCY 100% EFFICIENCY(%) 2.0 OUTPUT POWER(W) 20% 1.5 1.0 0.5 80% 60% 40% 20% 0% 0.0 -25 0 25 50 70 -10 100 Nom 5 10 INPUT VOLTAGE(%) TA(degree C) www.Power-Systems.de -5 Page: 4 / 5 Version: 4-Oct-02 DC-DC Converter UNIT CER Series (1.5 W REGULATED DC-DC CONVERTER) CER SERIES APPLICATION NOTES: EXTERNAL CAPACITANCE REQUIREMENTS: No external capacitance is required for operation of the CER series. To meet the reflected ripple requirements of the converter, an input impedance of less than 0.5 ohm from DC to 100KHz is required. External output capacitance is not required for operation, however it is recommended that 10uF tantalum and 0.1uF ceramic capacitance be selected for reduced system noise. Additional output capacitance may be added for increased filtering, but should not exceed 220uF. Negative Outputs: A negative output voltage may be obtained by connecting the +OUT to circuit ground and connecting –OUT as the negative output. FOR MORE INFORMATION CALL: Power Systems – The Power Solution Ilsfeld-Auenstein ( Germany ) Dörnet 8 Tel: + 49 / 70 62 / 67 59 – 6 E-mail: [email protected] Home Page: www.Power-Systems.de www.Power-Systems.de Page: 5 / 5 Fax: + 49 / 70 62 / 67 59 -80 Version: 4-Oct-02